PCA9534ADWR - 8-Bit I/O Expander | Texas Instruments
MPN: PCA9534ADWR ✓ פעילPCA9534ADWR סקירה
An I/O expander is an interface IC that converts serial commands into parallel digital control lines. The PCA9534ADWR belongs to the I/O expander class, where the broader hierarchy is interface IC, bus-controlled peripheral, and low-power semiconductor. It connects to a host through the two-wire I2C bus or compatible SMBus interface, allowing the host to read input states and configure output states through registers rather than dedicating eight GPIO pins on the host.
The principal features include eight configurable I/O lines, interrupt and configuration registers, operation across a 2.3 V to 5.5 V supply range, and 400 kHz I2C operation. Maximum standby current is listed as 1 uA, making the expander suitable for power-conscious embedded systems. The interrupt output is open-drain and active low, allowing multiple expansion devices to share an interrupt line when they are configured for the same bus address.
Each port pin can operate as an input or output, and the configuration registers determine the direction and electrical behavior of those pins. Register-based control permits software-defined mapping between bus commands and external circuitry. The serial interface also provides a practical way to add control lines without increasing the pin count of a microcontroller, processor, or programmable logic device. The PCA9534A family is described by Texas Instruments as pin-to-pin and I2C-address compatible with the PCF8574A, although software changes are required to use its enhanced register functions.
Typical applications include portable instrumentation, industrial control modules, sensor and switch interfaces, LED or relay control, programmable logic expansion, and compact embedded products. In a sensor interface, one device can gather several digital status inputs and drive multiple enables. In a control module, the same expander can operate an alarm line, mode selector, or status indicator while an interrupt tells the host that an input state has changed.
Designers should verify pin multiplexing, address selection, pull-up requirements, and open-drain interrupt wiring against the manufacturer datasheet before layout is released. Bus pull-up resistors depend on the operating voltage, bus capacitance, and selected clock rate. A common interface error is treating configuration-register bits as if they were direct port states, so firmware should initialize the device explicitly and test both input and output modes during bring-up.
This page combines device specifications, package and interface details, practical replacement guidance, and application-specific design guidance. It also distinguishes electrically similar devices from true pin-compatible choices, helping engineers assess replacement risk without treating a similar bus interface as proof of drop-in compatibility.
חלופות תחליף ישיר עבור PCA9534ADWR — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
TCA9534ADWR
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
PCA9534PWRG4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
PCA9534PW,118
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
PCA9534ADWR מפרטים
| Device Type | 8-bit I2C/SMBus I/O expander |
| Number of I/O Ports | 8 ports |
| Number of I/O Lines | 8 lines |
| Operating Supply Voltage Range | 2.3 V to 5.5 V |
| I2C Bus Frequency | 400 kHz |
| סוג ממשק | I2C and SMBus |
| Interrupt Output | Open-drain, active-low |
| Configuration Registers | Present |
| Maximum Standby Current | 1 uA |
| טווח טמפרטורת פעולה | -40 C to +85 C |
| מארז | 16-pin SOIC (DW) |
| סוג הרכבה | Surface mount |
| מספר פינים | 16 pins |
| Address Compatibility | Compatible with PCF8574A, with software changes required |
מדריך תצורת פינים של PCA9534ADWR 16-pin soic (dw)
תצורת פינים עבור PCA9534ADWR (מארזת 16-pin soic (dw)). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור PCA9534ADWR.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
PCA9534ADWR מתאים עבור 6 יישוםs: Portable Sensor and Switch Interface, Industrial Control Module, LED and Indicator Control, Programmable Logic Interface Expansion, Alarm and Security Peripheral, Automotive or Battery-Powered Equipment.
Portable Sensor and Switch Interface
The PCA9534ADWR is well suited to portable systems that must monitor several digital sensors and control selectors without assigning a dedicated GPIO to every signal. Its 8-bit port capacity provides eight configurable lines, while the 2.3 V to 5.5 V range supports low-voltage embedded systems. The 400 kHz I2C interface transfers port states efficiently, and the open-drain, active-low interrupt can notify the host when an input changes. Maximum standby current is 1 uA, helping preserve battery life during inactive periods. Place the device close to the external signal connector, keep the interrupt route away from high-current switching edges, and verify pull-up values against the intended bus voltage.
מומלץ
Industrial Control Module
In an industrial control module, PCA9534ADWR can consolidate digital mode inputs, fault flags, relay enables, and status LEDs behind an I2C bus. The device operates from 2.3 V to 5.5 V and supports 400 kHz communication, allowing it to coexist with common embedded control architectures. The interrupt output provides an efficient way for the controller to detect a changed input rather than continuously polling all eight lines. Configure input pins for the external voltage levels, define output polarities explicitly, and account for inrush current when switching inductive loads. Keep the expander’s supply and ground return close to the relevant circuitry so switching disturbances do not create false input transitions.
מומלץ
LED and Indicator Control
PCA9534ADWR can drive grouped LED indicators, panel status lights, and selection markers without expanding the host controller’s pin count. Eight configurable outputs provide flexible control for a display or control panel, while the 400 kHz I2C bus supports fast register updates. Because the device is a low-voltage digital expander, LED current limiting and any required transistor driver must be implemented separately rather than assumed to be integrated. Check output drive capability and absolute output limits in the manufacturer datasheet, and use current-limiting resistors on direct LED connections. A common-p cathode or common-anode arrangement can reduce component count, but programming polarity must match the physical wiring.
מומלץ
Programmable Logic Interface Expansion
The PCA9534ADWR is useful when a programmable-logic design needs additional discrete controls but its main I/O budget is constrained. A master controller can write configuration and port registers over I2C at up to 400 kHz, then read the eight input states when required. The 2.3 V to 5.5 V supply range allows integration with compatible logic levels, while the small 16-pin SOIC package supports compact layouts. Treat the interrupt line as a shared resource if several expanders are present, and ensure every attached device uses a unique address or is otherwise isolated. Timing closure must include bus capacitance, pull-up resistance, and the propagation delay of the external signals being monitored.
מומלץ
Alarm and Security Peripheral
PCA9534ADWR can collect door, tamper, presence, or enclosure status signals and drive local alarm-enable outputs in a compact security peripheral. The active-low, open-drain interrupt output is useful for signaling an input-state change to the host, while the eight-port count can combine several monitored inputs with a small number of control outputs. Operating down to 2.3 V supports embedded security equipment, and the 1 uA maximum standby current is beneficial in duty-cycled installations. Confirm the behavior of unused pins and the default state of every output after reset. For reliable detection, debounce mechanical inputs in firmware and account for contact bounce rather than treating every interrupt transition as an immediate alarm event.
מומלץ
Automotive or Battery-Powered Equipment
PCA9534ADWR can add remote control and status lines in battery-powered equipment where host GPIO availability is limited. Its 2.3 V minimum operating voltage, 1 uA maximum standby current, and eight configurable I/O lines support compact, low-power designs. The device can supervise switches, monitor enable signals, and control low-current indicators through I2C rather than direct host wiring. In a vehicle or other electrically noisy environment, maintain short return paths, decouple the supply locally, and validate every external signal against the pin voltage limits. A qualified automotive variant should be selected when AEC-Q100 requirements apply; the qualification status of this exact orderable code must be confirmed before release.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור PCA9534ADWR — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | TCA9534ADWR | PCA9534PWRG4 | PCA9534PW,118 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors |
| Package | 16-pin SOIC (DW) | 16-pin SOIC (DW) | 16-pin SOIC (DW) | 16-pin SOIC (DW) |
| Device Type | I/O Expander | I/O Expander | I/O Expander | I/O Expander |
| Number of I/O Lines | 8 lines | 8 lines | 8 lines | 8 lines |
| Bus Interface | I2C and SMBus | I2C | I2C and SMBus | I2C and SMBus |
| Price | Request a Quote | Request a Quote | Request a Quote | Request a Quote |
מבדילים עיקריים
- Directly identified PCA9534A-family orderable device (לעומתPCA9534PW,118)
- Same-manufacturer TCA9534 option (לעומתTCA9534ADWR)
- Eight configurable lines at a 400 kHz bus rate (לעומתPCA9534PWRG4)
- PCA9534A configuration and interrupt architecture (לעומתPCA9534PW,118)
הערות תכנון
Route SDA and SCL as a compact, continuous bus and place the required pull-up resistors near the master or the appropriate point defined by the system’s bus topology. The target supports 400 kHz, but usable speed also depends on total bus capacitance, pull-up resistance, clock stretching, and peripheral timing. Keep the I2C traces away from switching-power nodes and high-current relay or motor traces to reduce false edges and communication retries.
Do not assume that PCF8574A firmware can operate the PCA9534A without modification. Texas Instruments states that the devices are pin-to-pin and I2C-address compatible, while software changes are required for the PCA9534A enhancements. Review the configuration-register map, reset state, input polarity, output latch behavior, and interrupt semantics. Firmware should also initialize the direction register before driving outputs and account for mechanical input debounce where applicable.
Decouple the PCA9534ADWR supply with the capacitance recommended by the manufacturer datasheet and place it close to the device’s supply and ground pins. Although the listed maximum standby current is 1 uA, operating current and total system demand depend on clock activity and the states of the eight port lines. Use pull-up values appropriate for the operating voltage and bus capacitance, and calculate the worst-case logic-high current for any port that remains continuously active.
Treat the open-drain, active-low interrupt as a wired-AND resource when several expanders share it. Each device should be configured so its interrupt remains deasserted until the relevant input changes, and the shared line requires an appropriate pull-up. Keep the interrupt trace short and isolated from noisy coupling paths. Before production, compare every package drawing, including lead width, pitch, pin numbering, and exposed-pad requirements where applicable.
מידע על תאימות
The manufacturer product page and indexed technical descriptions do not state the complete compliance declarations for this orderable code. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status from the current manufacturer declarations before production release.