PCA9535D - 16-Bit I2C I/O Expander | NXP Semiconductors
MPN: PCA9535D ✗ Tapus ng BuhayPCA9535D Ulas
An I/O expander is an interface IC that increases the number of general-purpose input/output lines available to a host controller. In the product hierarchy, the PCA9535D belongs to the I/O expander class of interface ICs, connects to a host through I2C or SMBus, and serves as a bridge between serial control and parallel external circuitry. It is useful when a microcontroller, application processor, or programmable logic controller has too few pins for switches, indicators, sensors, or other digital peripherals.
The PCA9535D combines 16 configurable GPIO ports with a 400 kHz serial interface and an interrupt output. Its configuration registers allow software to select input or output direction and control the output state. The low-power design is a key distinction from the PCA9555: according to the manufacturer documentation, the PCA9535 omits the internal I/O pull-up resistors, which reduces power consumption when the ports are held low. The interrupt output provides a hardware indication that a port input has changed, reducing the need for continuous polling.
The device uses eight I2C addresses, allowing multiple expanders on one bus when their hardware address pins are configured appropriately. Bus operation is handled through SCL and SDA, while the port pins provide the parallel side of the interface. Because the PCA9535D is described as low-power and compatible with the PCA9555 interface concept, existing firmware can be evaluated against the PCA9555 for migration, although software and timing should still be checked for the specific replacement.
Typical uses include industrial control panels, sensor and relay interfaces, LED status panels, programmable instrumentation, and compact embedded systems that need additional digital lines. The interrupt output can wake or notify a host when an external switch or sensor changes state. In battery-powered equipment, configuring unused ports as inputs held low can help avoid unnecessary current consumption.
PCB design should preserve clear access to the SDA, SCL, address, reset, interrupt, supply, and ground pins. The serial bus requires suitable pull-up resistors and routing away from noisy switching nodes. Confirm the exact NXP pin assignments, operating limits, timing requirements, and recommended decoupling directly from the manufacturer datasheet before releasing the PCB or production firmware.
Mga alternatibo na pwedeng ilagay na PCA9535D — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok PCA9535D (parehas na form factor at footprint) — pagkakaiba sa Configuration Registers, Device Type, Interrupt Output, Package.
PCA9535DWR
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →PCA9535D Mga Spesipikasyon
| Device Type | 16-bit I2C/SMBus I/O expander with interrupt |
| Number of GPIO Ports | 16 ports |
| Supply Voltage Range | 2.3 V to 5.5 V |
| Maximum I2C Bus Frequency | 400 kHz |
| Interface | I2C and SMBus |
| Interrupt Output | 1 open-drain interrupt output |
| Configuration Registers | Input/output and output-state configuration registers |
| Device Address Capability | 8 I2C addresses |
| Internal I/O Pull-Up Resistors | Not fitted |
| Power Architecture | Low-power version of the PCA9555 |
| Process Technology | CMOS |
| Bilang ng Pin | 24 pins |
| Packhaging | SO24 |
| Uri ng Pagpapasok | Surface mount |
Pin Configuration ng PCA9535D
| Pin 1 | A0 — I2C address input |
| Pin 2 | A1 — I2C address input |
| Pin 3 | A2 — I2C address input |
| Pin 4 | VSS — Ground connection |
| Pin 5 | P00 — General-purpose I/O port 0 |
| Pin 6 | P01 — General-purpose I/O port 1 |
| Pin 7 | P02 — General-purpose I/O port 2 |
| Pin 8 | P03 — General-purpose I/O port 3 |
| Pin 9 | P04 — General-purpose I/O port 4 |
| Pin 10 | P05 — General-purpose I/O port 5 |
| Pin 11 | P06 — General-purpose I/O port 6 |
| Pin 12 | P07 — General-purpose I/O port 7 |
| Pin 13 | INT — Interrupt output |
| Pin 14 | P10 — General-purpose I/O port 10 |
| Pin 15 | P11 — General-purpose I/O port 11 |
| Pin 16 | P12 — General-purpose I/O port 12 |
| Pin 17 | P13 — General-purpose I/O port 13 |
| Pin 18 | P14 — General-purpose I/O port 14 |
| Pin 19 | P15 — General-purpose I/O port 15 |
| Pin 20 | VDD — Positive supply connection |
| Pin 21 | SCL — I2C or SMBus clock input |
| Pin 22 | SDA — I2C or SMBus bidirectional data line |
| Pin 23 | RESET — Active-low reset input |
| Pin 24 | NC — Not connected |
Tipikal na mga Gamit
PCA9535D ay nararapat para sa 6 aplikasyons: Industrial Control Panels, LED Status and Relay Interfaces, Sensor and Switch Acquisition, Programmable Test and Measurement Equipment, Communication and Network Equipment, Compact Embedded Controller Expansion.
Industrial Control Panels
The PCA9535D fits industrial control panels that require more switch, lamp, and interlock inputs than the host controller can provide directly. Its 16 ports can read panel contacts, operate status indicators, or control discrete interface signals through the I2C bus at up to 400 kHz. The interrupt output lets the controller respond when an input changes instead of continuously polling all 16 lines. Because the device is a low-power PCA9555 relative without internal I/O pull-ups, the panel design should include external pull-ups only where the wiring requires them. Firmware must configure each port direction before driving a connected actuator and account for the end-of-life status during product planning.
Inirekomenda
LED Status and Relay Interfaces
The PCA9535D is useful as a compact output driver for LED status groups and relay-control logic in embedded equipment. Sixteen configurable outputs provide more parallel control than most small microcontrollers while preserving a two-wire command path for configuration and state updates. The 400 kHz I2C rate allows the host to update multiple output bytes efficiently, and software-controlled outputs simplify state sequencing for indicators. For relay boards, keep inductive transient paths away from the compact digital device and provide the required coil suppression and grounding. The absence of internal I/O pull-ups helps minimize current when outputs are held low, but external pull-ups may be needed on open-drain or bus-connected signals.
Inirekomenda
Sensor and Switch Acquisition
The PCA9535D can consolidate binary sensors, selectors, limit switches, and panel contacts into a single I2C peripheral. Sixteen inputs reduce the host pin burden and eliminate separate multiplexers for basic digital states. When the host does not need continuous status, the interrupt output provides an event-driven indication that allows the controller to remain in a lower-power state until an input changes. Software should configure unused pins appropriately and apply suitable debouncing in firmware for mechanical contacts. The 24-pin SO24 footprint is practical for compact embedded boards, but the layout should preserve short, stable I2C routing and isolate switch wiring from sensitive analogue circuitry.
Inirekomenda
Programmable Test and Measurement Equipment
The PCA9535D is appropriate for programmable test equipment that needs numerous front-panel inputs and outputs while keeping the main controller footprint compact. It can control range-select relays, route logic-level signals, capture operator switches, and drive indicator LEDs through the 16 GPIO ports. Configuration registers permit software to change port direction without rewiring the instrument, while interrupt support avoids repeated status reads. The bus operates at up to 400 kHz, which is useful when multiple output groups must change during a test sequence. Because this NXP device is end of life, a new instrument should be reviewed against the PCA9535DWR alternative before schematic release and firmware reuse.
Inirekomenda
Communication and Network Equipment
The PCA9535D can serve as a local I/O endpoint in communication equipment where rear-panel connectors, status lamps, link controls, or alarm inputs exceed the host processor's available pins. The I2C interface allows the equipment controller to share the serial bus with other peripherals, while the interrupt line provides immediate notification of a changed rear-panel input. The device's low-power construction and lack of internal I/O pull-ups can reduce unnecessary current in systems that hold many lines low. In network-oriented products, place the expander away from high-current switching stages, maintain short bus routing, and verify that all address-selection configurations coexist with the intended bus population.
Inirekomenda
Compact Embedded Controller Expansion
The PCA9535D gives a compact microcontroller or application processor 16 additional GPIO lines without requiring a larger host package. A single I2C address can control LEDs, read buttons, operate latches, and monitor discrete system conditions, while the interrupt output supports responsive event handling. This is particularly useful when PCB area is constrained but board-level I/O remains extensive. The SO24 package supports straightforward surface-mount assembly, provided the PCB honors the manufacturer's pin and land-pattern requirements. Firmware should use the configuration and port registers from the manufacturer datasheet, test reset and power-up states, and include an end-of-life migration plan for production releases.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for PCA9535D — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | PCA9535DWR |
|---|---|---|
| Brand | NXP Semiconductors | Texas Instruments |
| Package | SO24 | 24-SOIC |
| GPIO Count | 16 bits | 16 bits |
| Serial Interface | I2C/SMBus | I2C/SMBus |
| Maximum Bus Frequency | 400 kHz | 400 kHz |
| Interrupt Output | Yes | Yes |
| Lifecycle Status | End of life | Active |
| Pin Count | 24 pins | 24 pins |
Pangunahing mga Pagkakaiba
- Low-power I/O expansion without internal port pull-ups (kumpara saPCA9555)
- Sixteen ports with event notification (kumpara saPCA9534APWR)
- Available active transition path for an end-of-life design (kumpara saPCA9535DWR)
Talaan ng Disenyo
Route SDA and SCL as short, continuous traces away from relay coils, switching-regulator power paths, and high-edge-rate inputs. The PCA9535D supports up to 400 kHz, so total bus capacitance, pull-up strength, and trace length must be evaluated together rather than treating the frequency rating as a board-level guarantee. Place the device near the connector or controlled peripheral group it serves, and keep the serial bus away from parallel GPIO traces that can switch simultaneously.
The PCA9535D omits the internal I/O pull-up resistors found on the PCA9555. Add external pull-ups only on signals that require a defined high state, and do not fit them automatically across every GPIO because that can increase current when the port is held low. Account for the selected external resistance, bus capacitance, and operating voltage when confirming that the complete I2C network meets the required rise time.
Do not treat every PCA9535-family ordering code as a footprint-compatible substitute. The target uses an SO24 package, while some family members are offered in TSSOP or other package forms. Compare the exact pin table, exposed dimensions, address inputs, reset behavior, interrupt polarity, electrical limits, and register map before releasing a replacement to production. The lifecycle status of an alternative should also be checked rather than inferred from its device-family name.
Configure unused GPIO pins during startup so they do not float or create unintended paths into external circuitry. For low-power operation, hold inputs in a defined state and avoid external pull-ups that continuously conduct. The PCA9535D's low-power design helps when ports are held low, but the complete current budget still depends on the supply voltage, bus activity, external pull-ups, and the attached peripheral circuits.
Impormasyon ng Pagsunod sa Kautusan
NXP labels PCA9535D as end of life. Compliance attributes were not stated in the manufacturer product listing, so each field remains unknown.