PCA9555BSHP - 16-Bit I2C I/O Expander | NXP | HVQFN-24
MPN: PCA9555BSHP ✓ NakahandaPCA9555BSHP Ulas
An I/O expander is an interface IC that increases the number of general-purpose digital input and output pins available to a host processor. The PCA9555BSHP occupies the level between a microcontroller and the discrete GPIO circuitry connected to it: the controller communicates over I2C or SMBus, while the expander converts eight register bits into eight outputs or reads back eight inputs. The integrated interrupt output reduces the need for continuous bus polling when an input changes state.
Three hardware address pins, A0, A1, and A2, select the fixed I2C-bus address of the device. According to the NXP product page, as many as eight PCA9555 devices can share one bus when the address pins are configured differently. The PCA9555 also uses the same fixed bus address as the PCA9554, allowing the two device types to coexist on a bus in combinations that do not produce an address conflict.
The 5.5 V maximum operating voltage and 400 kHz bus capability suit compact control boards, industrial modules, test equipment, and consumer accessories. The NXP part is identified with a 24-HVQFN exposed-pad package, which keeps the footprint compact while providing a thermal and electrical connection to the PCB ground plane. The exact exposed-pad construction and recommended land pattern should be taken directly from the manufacturer datasheet and package drawing.
Designers should confirm the I2C pull-up resistance, address-strapping levels, output-drive requirements, and exposed-pad connection in the manufacturer datasheet. Because this device expands ports rather than providing level shifting, its VDD and VSS pins must match the logic environment used by the host and attached peripherals. Care is also required when connecting outputs to loads that source current independently.
Mga alternatibo na pwedeng ilagay na PCA9555BSHP — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboPCA9555BSHP Mga Spesipikasyon
| Device Type | 16-bit I2C-bus/SMBus I/O expander with interrupt |
| Number of I/O Ports | 16 ports |
| Maximum I2C Bus Frequency | 400 kHz |
| Standard Bus Frequency | 100 kHz |
| Maximum Supply Voltage | 5.5 V |
| Address Configuration | 3 hardware address pins (A0, A1, A2) |
| Maximum Devices per Bus | 8 devices |
| Bus Compatibility | I2C-bus and SMBus |
| Interrupt Output | Yes |
| Packhaging | 24-HVQFN (4 x 4 mm) with exposed pad |
| Package Pin Count | 24 pins |
| Uri ng Pagpapasok | Surface mount |
| Shipping Format | Tape and reel |
Gabay sa Pin Configuration ng PCA9555BSHP 24 pins
Pin configuration para sa PCA9555BSHP (24 pins package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa PCA9555BSHP.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
PCA9555BSHP ay nararapat para sa 6 aplikasyons: Microcontroller GPIO Expansion, Industrial Control and Status Panel, LED and Relay Control, Battery-Powered Sensor Node, Test and Measurement Equipment, Networking and Communications Module.
Microcontroller GPIO Expansion
The PCA9555BSHP adds 16 configurable digital ports to a microcontroller or system-on-chip that has too few direct GPIO pins. The host writes direction, polarity, and output registers over I2C or SMBus, then reads the input register when the interrupt line indicates a change. At the 400 kHz maximum bus rate, command traffic is compact for a device with 16 ports. Its 4 x 4 mm HVQFN package also saves board area compared with a discrete bank of 16 GPIO components. The design should treat the interrupt line as an event request, not as the complete source of port state, because the firmware must still perform a register read to identify which input changed.
Inirekomenda
Industrial Control and Status Panel
A 16-bit expander is well suited to industrial control panels where limit switches, status lamps, relay enables, and alarm lines would otherwise consume many controller pins. The PCA9555BSHP supports I2C or SMBus operation up to 400 kHz, while the A0, A1, and A2 inputs permit multiple expanders to share one bus. Using the interrupt output, the controller can react to a changed input rather than repeatedly reading all 16 ports. For industrial environments, confirm the exact temperature grade and isolation requirements, and use appropriate board-level protection for external wiring because the expander pins are not inherently isolated surge inputs.
Inirekomenda
LED and Relay Control
The PCA9555BSHP can drive LED indicators, relay-control signals, and other digital loads when the chosen output configuration meets the load current and polarity requirements. Sixteen outputs allow a single bus device to replace separate driver circuitry for multiple indicators. Because the interrupt and address functions are provided in the same compact package, the design can also monitor switch states alongside controlling outputs. Engineers should verify output sink and source ratings in the manufacturer datasheet, account for inductive loads with appropriate suppression, and avoid driving a relay coil directly unless the device's specified output limits permit the peak current.
Inirekomenda
Battery-Powered Sensor Node
The PCA9555BSHP can consolidate multiple digital sensor-enable lines, configuration switches, and fault inputs on a compact sensor node. Its 16-bit I/O structure allows the host to share one serial bus with sensors or memory rather than assigning a dedicated GPIO pin to every function. The 5.5 V maximum operating voltage and 24-HVQFN package make it suitable for tightly spaced embedded assemblies. For battery-powered equipment, verify the device's actual quiescent current and active-state consumption in the manufacturer data, then compare those values with the module's sleep current because the expander may prevent the host controller from remaining the sole active device on the bus.
Inirekomenda
Test and Measurement Equipment
In a test instrument, the PCA9555BSHP can collect front-panel button states, module-present signals, and configuration selectors while also controlling status lamps or relay-select lines. The 400 kHz I2C capability supports efficient register access, and the interrupt output helps the controller avoid continuous serial polling when an operator changes a control. The compact 4 x 4 mm package preserves front-panel board area. A practical design should debounce mechanical inputs in firmware, define defaults for all output states during reset, and use the exposed-pad land pattern specified by the manufacturer to maintain reliable electrical and thermal performance.
Inirekomenda
Networking and Communications Module
The PCA9555BSHP can extend a communications module with additional port-monitor, link-status, configuration, or module-control signals. Its I2C address pins allow several expanders to coexist on a shared bus, including combinations with a PCA9554 because the two families use the same fixed address. The interrupt output is useful for monitoring remote line cards or transceiver-related control events without continuous polling. In network equipment, use the device only for logic-level control functions, and keep externally exposed lines behind the protection network required by the installation environment, including surge, overvoltage, and isolation considerations.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for PCA9555BSHP — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Talaan ng Disenyo
Route the exposed pad to the ground plane using the land pattern and via arrangement in the manufacturer package drawing. A compact 4 x 4 mm HVQFN package can be difficult to inspect after assembly, so verify pad alignment and exposed-pad soldering before releasing large production quantities. Keep the address straps, clock, and data traces away from noisy switching nodes.
Select I2C pull-up resistors using the bus capacitance, target rise time, and the 400 kHz operating rate rather than copying a single value across every board. Place pull-ups where they minimize the effective resistive loop and avoid long stubs from the expander to the bus. Confirm the actual pull-up voltage remains within the device's allowed input and supply levels.
Do not assume that two parts with similar PCA9555 functionality are mechanically interchangeable. The device family includes multiple package options, and exposed-pad construction can differ. Before substituting a component, compare the complete pin list, address behavior, register map, electrical limits, temperature range, and PCB land pattern against the original device.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer product-page summary does not state the requested compliance declarations. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status for the exact ordering code before release to production.