PCA9617ADPJ - 1MHz Fm+ I2C Level Shifter | NXP | TSSOP-8
MPN: PCA9617ADPJ ✓ NakahandaPCA9617ADPJ Ulas
A level-translating I2C buffer is an interface IC that allows two connected bus segments to operate at different logic voltages while preserving bidirectional clock and data communication. Its role within an interface hierarchy is a bidirectional bus repeater, followed by a level translator, followed by an interface IC. Bidirectional channels must actively reproduce the bus state in both directions so that pull-up resistors on each side can establish the correct local voltage.
The PCA9617A supports low-side voltages from 0.8 V to 5.5 V and high-side voltages from 2.2 V to 5.5 V. Its 1 MHz operating capability makes it suitable for Fast-mode Plus I2C traffic, while the independent dual-supply arrangement allows a low-voltage controller to communicate with higher-voltage peripherals. The NXP product is also identified as a one-channel signal buffer or re-driver in distributor catalogs.
The PCA9617A combines level translation with buffering. This allows a bus to remain usable when capacitance, voltage, or topology prevents direct connection between the two sections. Both I2C signal lines pass through the bidirectional repeater, and the enable control referenced to the high-side supply provides a way to place the drivers under system control. The enable state should only be changed while the bus is idle, preventing transitions on active clock or data lines.
Typical applications include separating low-voltage sensors from 3.3 V or 5 V controllers, extending I2C runs across voltage domains, protecting a bus segment from another subsystem, and supporting mixed-voltage system partitioning. The device can also be used in industrial control, instrumentation, communications equipment, and compact embedded systems where a 1 MHz I2C interface crosses between domains with incompatible logic levels.
The primary design consideration is correct pull-up placement. Each bus segment requires pull-up resistors referenced to its own supply voltage, and both sides should be configured for the voltages actually present in the design. The enable pin should be driven only while the I2C bus is idle. PCB layout should keep the two interface sections and their pull-up networks physically distinct to minimize coupling and maintain signal integrity.
This page combines the electrical operating ranges, interface function, package information, comparison guidance, and practical implementation considerations needed to evaluate the PCA9617ADPJ as a drop-in bus-interface candidate.
Mga alternatibo na pwedeng ilagay na PCA9617ADPJ — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok PCA9617ADPJ (parehas na form factor at footprint) — pagkakaiba sa Package, Number of Channels, RoHS Status, Function, Bus Compatibility.
TCA9617A
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
PCA9617ADPJ Mga Spesipikasyon
| Product Type | Level-translating bidirectional I2C-bus repeater |
| Low-Side Supply Voltage Range | 0.8 V to 5.5 V |
| High-Side Supply Voltage Range | 2.2 V to 5.5 V |
| Maximum Bus Frequency | 1 MHz |
| Supported Bus | I2C and SMBus |
| Supported I2C Speed | Fast-mode Plus (Fm+) |
| Signal Direction | Bidirectional |
| Channel Count | 1 channel |
| Device Architecture | CMOS integrated circuit |
| Enable Function | System-controlled driver enable referenced to VCC(B) |
| Packhaging | 8-pin TSSOP |
| Package Type | TSSOP-8 |
| Uri ng Pagpapasok | Surface mount |
| Packaging | Tape and reel |
| Tindminan RoHS | unknown |
| REACH Status | unknown |
Gabay sa Pin Configuration ng PCA9617ADPJ tssop-8
Pin configuration para sa PCA9617ADPJ (tssop-8 package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa PCA9617ADPJ.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
PCA9617ADPJ ay nararapat para sa 6 aplikasyons: Mixed-Voltage Sensor Interface, I2C Bus Extension, Industrial Control Module, Communications Equipment, Test and Measurement, Embedded System Power Domains.
Mixed-Voltage Sensor Interface
The PCA9617ADPJ fits when a 1 MHz sensor bus operates at a lower voltage than its controller. Place the repeater between the controller domain and the sensor domain, with each side connected to its own supply and pull-up network. The 0.8 V to 5.5 V low-side range accommodates very-low-voltage sensors, while the 2.2 V to 5.5 V high-side range supports 2.5 V, 3.3 V, or 5 V logic. Compared with a simple two-transistor level shifter, the active bidirectional repeater preserves the clock and data behavior required by Fast-mode Plus traffic while isolating the two bus segments.
Inirekomenda
I2C Bus Extension
The PCA9617ADPJ can divide a long or capacitively loaded I2C connection into separate bus segments while retaining operation up to 1 MHz. Each segment should have its own pull-up resistors connected to the supply used by that segment, and the PCA9617A repeater restores valid logic levels between them. This arrangement is useful when cable length, connector loading, or a bank of peripheral capacitance makes a single uninterrupted bus difficult to route reliably. The active buffer also provides controllable segmentation when two subsystems need to be electrically decoupled during part of the operating cycle.
Inirekomenda
Industrial Control Module
The PCA9617ADPJ is suitable for industrial control modules that separate a low-voltage sensor or logic island from a 3.3 V or 5 V control domain. Its 1 MHz Fast-mode Plus rating supports faster sensor and configuration traffic, while the independent supply ranges permit each island to use an appropriate voltage. Board partitioning should place the low-side and high-side pull-up networks on their respective supply rails and keep the enable control away from noisy switching nodes. The NXP manufacturer datasheet identifies the enable pin as referenced to VCC(B), so its inactive level must be defined by the high-side supply arrangement.
Inirekomenda
Communications Equipment
Communications equipment can use the PCA9617ADPJ to connect a low-voltage controller or transceiver logic section to a higher-voltage I2C peripheral section. The bidirectional repeater allows clock and data to flow in either direction while maintaining separate local voltage domains, which is valuable in line-card, base-station, and network-interface designs. At the 1 MHz operating limit, layout quality remains important: route SCL and SDA as a compact matched pair, terminate each bus segment with its own pull-ups, and avoid placing the repeater beside switching regulators without adequate isolation on the PCB.
Inirekomenda
Test and Measurement
The PCA9617ADPJ can separate a low-voltage acquisition or control section from a higher-voltage instrumentation domain in test and measurement systems. The device's 1 MHz rate and dual voltage ranges support I2C configuration traffic for sensors, converters, and programmable front ends while preventing incompatible logic levels from being applied directly. Each instrument-side bus segment needs pull-ups tied to its own reference supply, and the enable pin should only change state while the bus is idle. This allows a designer to preserve a reusable controller board across instruments that use different peripheral-side voltage levels.
Inirekomenda
Embedded System Power Domains
The PCA9617ADPJ is useful in an embedded system where a low-voltage domain controls sensors while a separate domain operates higher-voltage logic. The 0.8 V minimum low-side supply supports demanding sub-1 V logic, while the 2.2 V to 5.5 V high-side range accommodates conventional embedded rails. Because the part buffers the bus rather than merely translating a one-way signal, both SCL and SDA remain usable in either direction. Design the power-up sequence so that both supplies are stable before enabling the drivers, and observe the NXP manufacturer datasheet restriction against changing enable state during an active bus transfer.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for PCA9617ADPJ — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | TCA9617A |
|---|---|---|
| Package | TSSOP-8 | TSSOP-8 option required for exact PCB match |
| Brand | NXP Semiconductors | Texas Instruments |
| Product Type | Level-translating bidirectional I2C-bus repeater | Dual-supply level-translating I2C-bus repeater |
| Maximum Bus Frequency | 1 MHz | 1 MHz |
| Supported Bus | I2C and SMBus | I2C |
| Signal Direction | Bidirectional | Bidirectional |
Pangunahing mga Pagkakaiba
- Supports a very low 0.8 V low-side domain (kumpara saTCA9617A)
- Combines active buffering with level translation (kumpara saTCA9617A)
- Supports 1 MHz Fast-mode Plus operation (kumpara saTCA9617A)
Talaan ng Disenyo
Connect separate pull-up resistors to each bus segment and reference them to the supply used on that segment. Do not share pull-ups across the PCA9617ADPJ when the two sides operate at different voltages. Keep the SCL and SDA routes on the same side short, symmetrical, and away from switching nodes; the package should sit near the boundary between the two voltage domains so that each short connection remains within its intended supply region.
Change the enable state only while the I2C bus is idle. According to the NXP product information, the enable pin is referenced to VCC(B) and can turn the drivers on or off under system control. Asserting or releasing enable during an active clock or data transfer can create an unintended transition and corrupt the transaction. Define a deterministic startup state and release enable after the relevant supplies and pull-ups are stable.
Treat the PCA9617ADPJ as a partition boundary rather than only a signal-conditioning component. Route the low-voltage and high-side pull-up networks separately, observe current return paths for each supply, and keep the repeater away from high-di/dt switching loops. Because the device supports operation up to 1 MHz, maintain a continuous ground reference and minimize stubs on both SCL and SDA to reduce edge degradation and crosstalk.
Check rise-time behavior at 1 MHz rather than relying only on the nominal clock frequency. The actual bus rate depends on pull-up resistance, total bus capacitance, clock stretching, and the peripheral timing specifications. Use the highest effective capacitance present at the connector or test point when evaluating the design, and ensure the selected values support the required Fast-mode Plus timing across temperature and process variation.
Impormasyon ng Pagsunod sa Kautusan
No definitive target-part compliance declarations were identified. AEC-Q100 is not applicable to this general-purpose interface IC.