PCF8574PWG4 - 8-Bit I2C I/O Expander | Texas Instruments
MPN: PCF8574PWG4 ✓ NakahandaPCF8574PWG4 Ulas
An I/O expander, also called a port expander, increases the number of digital input and output pins available to a host microcontroller. The PCF8574 belongs to the interface-controller hierarchy: I/O expander → interface IC → integrated circuit → semiconductor. Its I2C interface allows a microcontroller to read and control eight external lines using serial data and clock signals instead of dedicating eight parallel GPIO pins to every peripheral.
The PCF8574PWG4 features an 8-bit quasi-bidirectional port, a 100 kHz I2C interface, and a 20-pin TSSOP package. Its interrupt output can alert the host when an input state changes, helping the controller avoid continuous polling. Power-on reset provides a defined startup state for the I/O port, while the quasi-bidirectional outputs can source or sink current depending on operating state.
The I2C interface supports connection to a broad range of microcontrollers and embedded systems. Address selection is commonly implemented through input pins, allowing multiple expanders to share the same bus when the device configuration supports it. Because the port uses quasi-bidirectional structures, designers should review the device datasheet for output-drive, input, pull-up, and current-limit details before driving external loads.
Typical uses include reading push buttons and selectors, controlling LEDs or discrete relays, monitoring digital sensors, and expanding the I/O capacity of industrial controllers, appliances, instruments, and consumer equipment. The 20-pin TSSOP package also supports compact board layouts where a larger dual-inline package would be inconvenient.
For a new layout, route the I2C pins according to the datasheet pin description and place pull-up resistors close to the bus master. Confirm the logic-level voltage of every connected device, preserve the power-on reset behavior, and calculate the total port and bus loading before enabling multiple expanders. Use the manufacturer pin-description table when assigning PCB tracks and connector signals.
This product page organizes the exact MPN, package, interface details, verified distribution information, replacement guidance, and practical integration considerations for engineers evaluating the PCF8574PWG4.
Mga alternatibo na pwedeng ilagay na PCF8574PWG4 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok PCF8574PWG4 (parehas na form factor at footprint) — pagkakaiba sa Interface, Interrupt Output, Package.
PCF8574PW
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →PCF8574PWR
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →PCF8574APWR
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
PCF8574PWG4 Mga Spesipikasyon
| Device Type | 8-bit remote I/O expander |
| Number of I/O Lines | 8 |
| Interface | I2C |
| Maximum I2C Clock Frequency | 100 kHz |
| Type ng Output | Push-pull |
| Interrupt Output | Yes |
| Power-On Reset | Yes |
| Output Source Current | 1 mA |
| Output Sink Current | 25 mA |
| Packhaging | 20-pin TSSOP |
| Uri ng Pagpapasok | Surface mount |
| Shipping Package | Tape and reel |
Gabay sa Pin Configuration ng PCF8574PWG4 tape and reel
Pin configuration para sa PCF8574PWG4 (tape and reel package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa PCF8574PWG4.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
PCF8574PWG4 ay nararapat para sa 6 aplikasyons: Microcontroller GPIO Expansion, LED and Indicator Control, Industrial Relay and Discrete Control, Appliance and Control Panel Interface, Digital Sensor and Input Aggregation, Test and Measurement Front Panel.
Microcontroller GPIO Expansion
PCF8574PWG4 fits designs in which a host microcontroller has too few direct GPIO pins for buttons, indicators, and discrete control signals. The eight quasi-bidirectional lines connect to the I2C bus, while the interrupt output lets the controller react to a changed input without continuously polling every port bit. At a maximum bus rate of 100 kHz, the device is appropriate for moderate-speed human-interface and control traffic rather than high-rate data acquisition. Designers should treat each port line as a limited quasi-bidirectional resource, configure the correct address, and verify the connected MCU and peripheral logic levels before power-up.
Inirekomenda
LED and Indicator Control
PCF8574PWG4 provides a compact way to add grouped indicator outputs to a controller with limited GPIO resources. Each of the eight quasi-bidirectional lines can control a discrete LED or related interface signal, with the I2C bus carrying output updates at up to 100 kHz. This arrangement reduces direct MCU pin usage and centralizes indicator control in firmware. Because the port has finite source and sink-current ratings, calculate each line's load and avoid exceeding the per-pin and aggregate limits in the Texas Instruments datasheet. High-current LEDs should therefore use a suitable transistor driver rather than being connected directly without validation.
Inirekomenda
Industrial Relay and Discrete Control
PCF8574PWG4 can form the low-current control interface of an industrial monitoring or relay-control board when the external relay drivers include suitable isolation and flyback components. The eight output lines organize the control commands, and the interrupt output supports change-driven communication with the host. The 100 kHz I2C interface provides ample bandwidth for ordinary supervisory commands rather than continuous high-speed feedback. Because the quasi-bidirectional port is not intended for unlimited inductive loads, use transistor or MOSFET driver stages for coils and ensure the driver polarity, isolation, and flyback path match the selected relay.
Inirekomenda
Appliance and Control Panel Interface
PCF8574PWG4 suits appliance control panels where switches, selectors, indicators, and small solenoid controls exceed the direct I/O budget of the main controller. The I2C connection reduces PCB routing compared with a wide parallel port, while the interrupt line alerts the appliance controller when a user input changes. The compact 20-pin TSSOP format supports space-conscious control boards and can be placed near the panel connector. Firmware should debounce mechanical contacts, establish a deterministic startup state, and avoid driving external loads beyond the published output-current capability of the selected port line.
Inirekomenda
Digital Sensor and Input Aggregation
PCF8574PWG4 can aggregate slow-changing digital signals from limit switches, interlocks, selectors, and discrete sensor outputs behind one I2C address. Eight monitored lines reduce the number of direct host-controller inputs, and the interrupt output supports a responsive polling strategy. The 100 kHz interface is suitable for low-rate supervisory signals but should not be treated as a high-speed data-acquisition channel. The host must correctly handle quasi-bidirectional port reads, debounce contacts, account for address configuration, and keep all connected logic levels within the device's supply-voltage range.
Inirekomenda
Test and Measurement Front Panel
PCF8574PWG4 is useful in an instrument front panel where status LEDs, range indicators, and user switches would otherwise consume a large share of a controller's GPIO resources. The I2C interface allows the main controller to update panel indications and read operating-mode selections efficiently, and the interrupt output provides event-driven input handling. A 100 kHz bus is more than adequate for human interaction and supervisory state changes. Keep the connector and panel circuitry away from noisy analog sections, establish grounding that avoids panel-current paths through sensitive measurement returns, and confirm that every output state during reset is acceptable for the instrument.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for PCF8574PWG4 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | PCF8574PW | PCF8574PWR | PCF8574APWR |
|---|---|---|---|---|
| Package | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of I/O Lines | 8 | 8 | 8 | 8 |
| Interface | I2C | I2C | I2C | I2C |
| I2C Clock Frequency | 100 kHz | 100 kHz | 100 kHz | 100 kHz |
| Output Type | Push-pull | Push-pull | Push-pull | Push-pull |
| Interrupt Output | Yes | Yes | Yes | Yes |
| Power-On Reset | Yes | Yes | Yes | Yes |
| Special Feature | 8-bit quasi-bidirectional I/O port with interrupt | 8-bit I/O port with interrupt | 8-bit I/O port with interrupt | 8-bit I/O port with interrupt and different fixed address |
Pangunahing mga Pagkakaiba
- Provides eight control lines without consuming eight direct MCU GPIO pins (kumpara saPCF8574DWRE4)
- Supports event-driven host-controller operation (kumpara saPCF8574DWRE4)
- Direct same-footprint replacement path exists within the PCF8574 family (kumpara saPCF8574DWRE4)
Talaan ng Disenyo
Use the Texas Instruments PCF8574PWG4 pin-description table when routing the 20-pin TSSOP footprint. Place the device close to the connector or controlled peripheral group to minimize trace length, and keep I2C routing away from switching nodes and high-current relay paths. Confirm whether the application requires a reset connection and preserve access to all address-selection pins; incorrect fixed wiring can place multiple expanders at the same bus address.
The I2C bus requires pull-up resistors to the selected logic voltage. Calculate the resistor value from bus capacitance, sink-current limits, rise-time requirements, and the voltage drop at the lowest bus level. Place the pull-ups at the locations recommended by the system architecture, normally near the bus master or the point where the bus is least susceptible to leakage. Confirm that every pull-up remains within the PCF8574PWG4 input-voltage range during normal operation and power transitions.
Do not treat the eight port pins as unrestricted push-pull outputs or inputs. Review the quasi-bidirectional port behavior, per-line source current of 1 mA, sink current of 25 mA, and the required pull-up arrangement before attaching LEDs, relays, or other loads. Use a transistor driver for higher-current or inductive loads, and include suitable flyback protection. The interrupt signal is useful for input changes but does not remove the need to debounce mechanical contacts.
Keep the I2C traces short, continuous, and away from noisy analog or switching paths when possible. Route SDA and SCL consistently to minimize differential skew, use the package pin assignments shown in the manufacturer datasheet, and avoid unnecessary stubs on the bus. If the assembly requires split routing or long cable-like branches, validate rise time and communication margin at the 100 kHz operating rate before production.
Define the state of all eight external loads during power-on reset. The reset function gives the interface a defined startup condition, but external pull-ups, relay drivers, or connected peripherals can still transform that state into unwanted current or motion. Sequence sensitive loads with suitable gating hardware and verify the complete power-up behavior across the minimum and maximum supply conditions rather than relying only on the PCF8574 port state.
Impormasyon ng Pagsunod sa Kautusan
The product listing identifies the PCF8574PWG4 as an 8-bit I2C 100 kHz I/O expander in a 20-pin TSSOP package. Detailed RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not stated, so these fields remain unknown.