PCF8575PWE4 - 16-Bit I2C/SMBus I/O Expander by TI
MPN: PCF8575PWE4 ✓ NakahandaPCF8575PWE4 Ulas
An I/O expander is an interface IC that increases the number of digital input and output lines available to a host microcontroller or other bus controller. The PCF8575 connects through the two-wire I2C or SMBus interface, while its parallel port provides individual control and status signals for attached peripherals. In the product hierarchy, it is an I/O expander, bus interface IC, and semiconductor designed for embedded control and general-purpose remote I/O.
The principal features include 16 individually addressable I/O lines, two parallel ports, a 2.5 V to 5.5 V operating supply range, and an open-drain interrupt output. The I2C interface operates up to 400 kHz, and the device has maximum standby-current consumption of 10 uA. Address selection by hardware pins allows multiple expanders to coexist on one bus without using a large number of host I/O pins.
Communication with the PCF8575 uses serial clock and serial data lines, while power-down, reset, port 0, port 1, and interrupt functions occupy dedicated pins. Quasi-bidirectional ports can source output current, accept logic inputs, and participate in partial high-impedance operation. The open-drain interrupt output provides a common hardware indication that one or more port inputs have changed, allowing the host to service the device without continuously polling every line.
Typical uses include industrial control panels, sensor and actuator interfaces, programmable instrument front panels, embedded data-acquisition systems, and compact control boards that need more digital lines than the host controller provides. The 2.5 V minimum supply supports low-voltage embedded systems, while the 5.5 V maximum allows operation from a conventional 5 V rail. The 24-pin TSSOP package also fits densely populated PCB layouts with 0.65 mm lead spacing.
Design the bus pull-up network for the selected SCL and SCL frequency and system capacitance, and account for the voltage drop contributed by pull-up resistance when more than one expander drives the bus low. Confirm that every connected node is 5 V tolerant before using the 5.5 V maximum supply. Preserve the interrupt output's open-drain behavior and provide suitable pull-up or signal-conditioning arrangements where required.
This page organizes the key electrical characteristics, complete package information, direct replacement options, and practical bus-layout guidance for engineers evaluating the PCF8575PWE4. It also provides focused comparisons for determining whether an alternative offers a meaningful functional or lifecycle advantage without requiring a PCB footprint change.
Mga alternatibo na pwedeng ilagay na PCF8575PWE4 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok PCF8575PWE4 (parehas na form factor at footprint) — pagkakaiba sa Maximum Standby Current.
PCF8575PWRE4
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
TCA6416PWTG4
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
PCF8575PWE4 Mga Spesipikasyon
| Number of I/O Lines | 16 lines |
| Port Configuration | 2 ports of 8 I/O lines |
| Supply Voltage na Operasyon | 2.5 V to 5.5 V |
| Nominal Supply Voltage | 3.3 V |
| I2C Bus Frequency | 400 kHz maximum |
| Supported Serial Interfaces | I2C and SMBus |
| Interrupt Output | Open-drain |
| Maximum Standby Current | 10 uA maximum |
| Port Output Characteristics | Quasi-bidirectional CMOS I/O |
| Address Configuration | Hardware-selectable bus address |
| Terminal Pitch | 0.65 mm |
| Package Description | 24-pin PDSO/TSSOP |
| Uri ng Pagpapasok | Surface mount |
| Device Category | Remote 16-bit parallel I/O expander |
Gabay sa Pin Configuration ng PCF8575PWE4 24-pin pdso/tssop
Pin configuration para sa PCF8575PWE4 (24-pin pdso/tssop package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa PCF8575PWE4.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
PCF8575PWE4 ay nararapat para sa 6 aplikasyons: Industrial Control Panel Interface, Sensor and Actuator Hub, Programmable Instrument Front Panel, Data Acquisition Front End, LED and Discrete Control Module, Embedded Communication Interface Hub.
Industrial Control Panel Interface
The PCF8575PWE4 fits industrial control panels where a host controller needs more panel I/O than its native pin count allows. Its 16 quasi-bidirectional lines can drive status indicators and read discrete inputs, while the 2.5 V to 5.5 V operating range supports both 3.3 V and 5 V control logic. The open-drain interrupt output allows the controller to respond to a changed input without continuously polling all 16 lines. The 24-pin TSSOP package with 0.65 mm pitch preserves board area in compact panels. Designers should verify relay-driver interfaces, input debouncing, and the exact operating-temperature grade for the deployed enclosure.
Inirekomenda
Sensor and Actuator Hub
The PCF8575PWE4 can act as a remote sensor and actuator hub when the primary controller has too few direct GPIO pins for discrete devices. Sixteen independently controlled lines support digital sensors, relay-control stages, and status feedback through the two 8-bit ports. Operation from 2.5 V to 5.5 V accommodates common embedded logic levels, and the 400 kHz I2C capability allows updates to occur quickly enough for many control loops. The interrupt function signals an input transition, helping the host avoid constant register reads. Engineering checks should include output-load current, input thresholds, external pull-ups, isolation requirements, and protection against connector-borne transients.
Inirekomenda
Programmable Instrument Front Panel
The PCF8575PWE4 is useful in programmable laboratory instruments where front-panel switches, indicators, and mode controls would otherwise consume most host GPIO resources. The two 8-bit ports provide 16 local lines, and the 400 kHz I2C link supports responsive panel updates from a host processor. Its 24-pin TSSOP footprint helps maintain dense instrument layouts, while the 10 uA maximum standby current supports low-power operating states. The interrupt output can indicate a changed front-panel control before the host performs a complete status read. Designers should use suitable logic buffering for long switch wiring and account for LED current, switch bounce, and exposed-panel ESD protection in the final circuit.
Inirekomenda
Data Acquisition Front End
The PCF8575PWE4 can extend a data-acquisition system by collecting digital channel status, controlling range or mode enables, and reading external instrumentation flags. Its 16 lines and interrupt output reduce the number of host connections required for remote control and status. The 2.5 V minimum supply supports 3.3 V acquisition controllers, while 400 kHz I2C operation supports reasonably rapid configuration updates. The compact 24-pin TSSOP package leaves routing space for analog and mixed-signal circuitry. Signal-integrity review should account for bus capacitance, pull-up sizing, separation from high-switching analog nodes, and any external isolation between field-wired inputs and the logic ground.
Inirekomenda
LED and Discrete Control Module
The PCF8575PWE4 is appropriate for a remote LED and discrete-control module because its 16 quasi-bidirectional lines can operate indicator LEDs or drive external transistor stages while returning device status. The I2C interface keeps the host wiring compact, and the open-drain interrupt output can report a changed status input without continuous polling. Its 2.5 V to 5.5 V range permits integration with 3.3 V systems, and the 24-pin TSSOP package supports compact LED-control boards. Designers must respect each port's current limits, account for LED forward current and resistor tolerances, and use suitable drivers when a load exceeds the direct output capability. Common-anode or common-cathode LED arrangements should be checked against the selected drive method.
Inirekomenda
Embedded Communication Interface Hub
The PCF8575PWE4 can serve as an I/O companion to a communications-oriented controller that needs additional discrete lines for modem control, link status, configuration, or peripheral enables. The 16-bit port capacity consolidates these controls over I2C, while the interrupt output provides an event-driven indication of remote state changes. The device supports 2.5 V to 5.5 V operation and a 400 kHz bus, matching many embedded communication designs. In a network or router-adjacent assembly, the package should be placed away from switching supplies and high-energy lines. Designers should validate signal levels, bus loading, pull-up values, and grounding or isolation requirements for externally accessible communication interfaces.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for PCF8575PWE4 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | PCF8575PWRE4 | TCA6416PWTG4 |
|---|---|---|---|
| Package | TSSOP-24 | TSSOP-24 | TSSOP-24 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| I/O Lines | 16 lines | 16 lines | 16 lines |
| Serial Interface Support | I2C and SMBus | I2C and SMBus | I2C |
Pangunahing mga Pagkakaiba
- Provides 16 remote I/O lines through two 8-bit ports (kumpara saTCA6416PWTG4)
- Supports a broad 2.5 V to 5.5 V operating range (kumpara saTCA6416PWTG4)
- Low 10 uA maximum standby current (kumpara saPCF8575PWRE4)
Talaan ng Disenyo
Use the manufacturer land pattern for the 24-pin PW-family package and verify the 0.65 mm lead pitch against the PCB library. Place the device near the connector or controlled peripheral group, but keep the I2C route away from switching nodes and long parallel spans that can increase capacitive loading. Provide unobstructed access to address-selection, power-down, reset, and interrupt pins. Confirm the pin-direction table in the manufacturer datasheet before connecting circuitry because the port behavior differs between input, output-high, and quasi-bidirectional states.
Size the SDA and SCL pull-ups from bus voltage, total capacitance, rise-time requirements, and the number of attached devices rather than using an arbitrary resistance. The PCF8575 supports I2C operation up to 400 kHz, but long wiring or excessive capacitance can prevent compliant rise times even when the nominal clock rate is acceptable. Check the pull-up current at each logic-low state, account for the parallel contribution of all connected devices, and avoid large pull-up values that make the bus too slow for the selected operating frequency.
Do not treat the quasi-bidirectional ports as unrestricted push-pull outputs. Each port may be driven high by the expander for only a limited period before an external pull-up must sustain the high state. Review the data-sheet timing limits before using an output to drive a continuously energized load, and use a transistor or driver stage where required. Also observe power-down and reset behavior, ensure all connected nodes remain within the device's voltage limits, and confirm the polarity and pull-up arrangement of the open-drain interrupt line.
Impormasyon ng Pagsunod sa Kautusan
The available product information does not explicitly state the requested environmental or material-compliance statuses. These fields remain unknown until confirmed against the manufacturer's compliance documentation for the exact orderable part.