SN74LS243N - Quad 4-Bit Bus Transceiver | Texas Instruments
MPN: SN74LS243N ✓ NakahandaSN74LS243N Ulas
A bus transceiver is a digital interface component that places a driver on one side of a bus and a receiver on the other. This arrangement allows two independently operating bus systems to share a physical connection and transfer data in either direction. In the broader integrated-circuit hierarchy, the SN74LS243N belongs to the 74LS TTL logic family and provides the physical-layer interface between a bus driver or peripheral and a processor data bus.
The principal functional attributes include a non-inverting signal path, four parallel data lines per transceiver element, push-pull output capability, and support for terminated lines down to 133 ohms. Its 14-pin PDIP package provides through-hole mounting for industrial, control, instrumentation, and legacy computer-interface designs. The manufacturer describes the SN74LS243 commercial-temperature family variant for operation from 0°C to 70°C.
The SN74LS243N is useful when two bus sections need bidirectional communication but are not always driven by the same controller. The transceiver separates the transmit and receive functions while presenting compatible logic signaling to both sides. This architecture reduces the number of discrete buffers required in multi-master or bus-isolation arrangements and simplifies routing compared with separate one-way buffers.
Typical uses include asynchronous data exchange, test equipment interfaces, peripheral connections, control-panel communication, and industrial systems that retain 74LS logic interfaces. The 133-ohm terminated-line capability makes the device relevant to legacy backplane and cable-oriented bus designs where controlled impedance and reliable signal return are important.
PCB implementation should preserve a continuous ground reference and place bypass capacitance close to the supply pins. Because the SN74LS243N is a through-hole 14-pin PDIP device, its pin spacing and drilled footprint must match the selected package drawing. Designers should also check bus direction-control sequencing and signal termination in the complete circuit.
This product page combines the manufacturer function description, package and ordering information, supported operating characteristics, cross-reference results, practical bus-interface guidance, and engineering selection criteria. Those details help distinguish a genuine 74LS bus-transceiver assembly from CMOS-interface devices that may share a similar footprint but require different logic-level and timing validation.
Mga alternatibo na pwedeng ilagay na SN74LS243N — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
SN74LS243NE4
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
SN74LS243N3
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
SN74LS243N Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | Quad 4-bit bus transceiver |
| Number of Elements | 4 elements |
| Data Lines per Element | 4 bits per element |
| Signal Polarity | Non-inverting |
| Type ng Output | Push-pull |
| Communication Mode | Asynchronous two-way |
| Minimum Terminated Line Resistance | 133 ohm |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Commercial Operating Temperature Range | 0°C to 70°C |
| Military Operating Temperature Range | -55°C to 125°C for SN54LS243 |
| Packhaging | 14-pin PDIP |
| Package Pin Count | 14 pins |
| Uri ng Pagpapasok | Through-hole |
| Logic Family | 74LS TTL |
| Manufacturer Product Page | https://www.ti.com/product/SN74LS243 |
Gabay sa Pin Configuration ng SN74LS243N 14 pins
Pin configuration para sa SN74LS243N (14 pins package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa SN74LS243N.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
SN74LS243N ay nararapat para sa 6 aplikasyons: Asynchronous Two-Way Bus Interface, Industrial Controller Bus Isolation, Test and Measurement Equipment, Legacy Peripheral Data Exchange, Control Panel Communication, Legacy Backplane Data Routing.
Asynchronous Two-Way Bus Interface
The SN74LS243N is suited to linking two asynchronous bus sections that require separate transmit and receive paths. Its four elements each carry four data lines, allowing four parallel bits to cross between the two sides of the interface in a 5 V 74LS system. The non-inverting push-pull architecture preserves signal polarity and supports deterministic bus signaling. When implementing the interface, use the manufacturer pin configuration and establish correct direction-control sequencing for every connected driver so that multiple outputs never contend on the same line.
Inirekomenda
Industrial Controller Bus Isolation
The SN74LS243N can isolate the physical receive and drive functions of a legacy 74LS controller bus from another subsystem. Its four 4-bit groups are useful where several low- and medium-speed control lines must cross a bus boundary without tying the two controllers together. The 5 V operating range and 0°C to 70°C commercial specification suit controlled industrial equipment. The design should include a continuous ground reference, local supply bypassing, and deliberate bus termination; the device’s ability to drive lines down to 133 ohms supports legacy terminated-bus arrangements.
Inirekomenda
Test and Measurement Equipment
A quadruple bus transceiver is useful in test equipment that must route control or measurement data between an instrument and an external fixture. The SN74LS243N provides four parallel, non-inverting data paths per element while maintaining 74LS-compatible system signaling. This allows transmitter and receiver circuitry to be placed on opposite sides of a cable or board interface without merging their drive outputs directly. For reliable operation, keep the interconnect short, control reflection with the appropriate termination, and account for the bandwidth and timing margins of the 74LS implementation.
Inirekomenda
Legacy Peripheral Data Exchange
The SN74LS243N supports older processor and peripheral systems that exchange four-bit data groups using 5 V 74LS signaling. Its four transceiver elements can connect host-side and peripheral-side buses while keeping the two interface directions electrically organized. This is particularly useful when upgrading a mixed-vintage installation without changing the established 14-pin through-hole logic footprint. Firmware designers should define bus ownership before enabling either direction, and hardware designers should preserve adequate settling time for the slower LS-series transition behavior.
Inirekomenda
Control Panel Communication
The SN74LS243N can form part of a control-panel communication path where an operator interface or remote controller exchanges four parallel data bits with a central control system. The non-inverting signal path simplifies compatibility with existing 74LS logic, while the push-pull outputs support driven bus lines rather than passive open-collector signaling. In a panel design, keep the transceiver close to the connector and protection circuitry, provide a low-impedance ground return, and isolate the interface from motor switching or relay transients to avoid disturbing the 5 V logic rail.
Inirekomenda
Legacy Backplane Data Routing
The SN74LS243N is applicable to legacy backplanes that use four-bit parallel data paths and require bidirectional communication between bus segments. Its manufacturer-described ability to drive terminated lines down to 133 ohms is relevant when card-edge cables, short backplane traces, or controlled-impedance interconnects are used. The device should be placed where driver and receiver loading can be evaluated separately. Designers must also avoid excessive capacitive loading, maintain return paths, and validate timing at the slowest supported bus rate rather than relying only on rise-time estimates.
Inirekomenda
Impormasyon ng Talumpati sa Engineering for SN74LS243N — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | SN74LS243NE4 | SN74LS243N3 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin PDIP | 14-pin PDIP - same | 14-pin PDIP - same |
| Device Type | Quad bus transceiver | Quad bus transceiver | Quad bus transceiver |
| Elements | 4 elements | 4 elements | 4 elements |
| Data Lines per Element | 4 bits per element | 4 bits per element | 4 bits per element |
| Supply Voltage Range | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Signal Polarity | Non-inverting | Non-inverting | Non-inverting |
| Output Type | Push-pull | Push-pull | Push-pull |
| Minimum Terminated Line Resistance | 133 ohm | 133 ohm | 133 ohm |
Pangunahing mga Pagkakaiba
- Directly preserves the legacy 74LS bus interface (kumpara sa74HC243N)
- Matches the specified 4-bit-per-element bus organization (kumpara saSN74LS243N3)
- Maintains the original 14-pin PDIP implementation (kumpara saSN74LS243NE4)
Talaan ng Disenyo
Use the exact 14-pin PDIP footprint and verify row spacing against the TI package drawing before releasing the PCB. Keep the ground plane continuous beneath and around the device, place input and output traces away from unrelated switching nodes, and connect the supply bypass capacitor close to the package power and ground pins. The DIP outline alone is not enough to confirm mechanical interchangeability.
Termination must match the physical bus rather than being added solely because the SN74LS243N can drive terminated lines down to 133 ohms. Evaluate trace length, connector capacitance, stub branches, and the source impedance of every enabled driver. Disable unused bus drivers before direction changes so that a transition interval does not place two push-pull outputs in contention.
Do not treat a 74HC243 as an unconditional drop-in replacement for a 74LS bus. CMOS-family input thresholds, output levels, supply range, and transition behavior can differ even when the package and broad transceiver function match. For the SN74LS243N alternatives, confirm the ordering suffix and manufacturer ordering information rather than changing the part solely on a distributor search result.
Provide a stable 5 V supply within the 4.75 V to 5.25 V operating range and decouple the device close to its supply pins. When the transceiver drives a terminated line, calculate source current from the actual bus voltage and termination resistance rather than assuming the minimum supported line resistance applies continuously. This helps prevent excess driver dissipation or rail droop during simultaneous data transitions.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer material confirms the function, 5 V supply range, commercial-temperature characterization, package, and terminated-line capability. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified, so those fields remain unknown. AEC-Q100 is not applicable to this standard commercial logic device.