SN74LS640M - Octal Bus Transceiver | onsemi | SOIC-20
MPN: SN74LS640M ✓ NakahandaSN74LS640M Ulas
A bus transceiver is an interface-circuit category that connects two independently timed digital buses while adding direction and output control. The SN74LS640 belongs to the broader 74LS low-power Schottky TTL logic family, combining bidirectional data paths with bus-driver and bus-receiver functions. Its octal organization allows an entire eight-bit data word to be transferred between two buses through one 20-pin device.
The primary benefit of the SN74LS640M is integrated directional control. The DIR input determines the direction of data flow, while the output-enable input provides shared control over the eight output drivers. This arrangement reduces the number of external control gates and simplifies asynchronous system interfacing. Its octal structure also allows parallel processors, memory systems, peripheral controllers, and data-acquisition equipment to use one package for full-width bus buffering.
As a member of the SN54LS64x and SN74LS64x bus-transceiver family, the SN74LS640M is covered by the manufacturer's octal bus transceiver datasheet. That document also describes related SN74LS641, SN74LS642, SN74LS645, and military-temperature SN54LS64x devices. Because this is a low-power Schottky TTL device, system designers should preserve adequate input rise and fall times, maintain compatible VCC rails, and avoid excessive capacitive loading on the bus outputs.
Typical uses include bidirectional processor-bus isolation, memory-buffer interfaces, peripheral data buses, industrial control data exchange, and legacy digital test equipment. The transceiver is especially useful where two bus masters may alternate control of a shared eight-bit data path. The enable input can also isolate the device during reset, test, or bus turnaround, reducing contention risk when multiple sources share a conductive path.
PCB implementation should prioritize short, clean signal traces and a solid ground reference. Place the device close to the bus connector or processor interface, keep the DIR and output-enable traces away from high-current switching paths, and provide local bypass capacitance at VCC. Confirm that the connected devices use compatible TTL signal levels and that the enabled direction matches the intended source and destination buses.
This page consolidates the device function, package details, operating context, design guidance, and documented replacement options into one engineering reference. It also identifies where compatibility must be checked against pinout, power requirements, timing, and lifecycle constraints before approving a substitute for an existing design.
Mga alternatibo na pwedeng ilagay na SN74LS640M — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
SN74LS640MEL
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
SN74LS640-1NSR
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
SN74LS640NSRE4
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
SN74LS640DW
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
SN74LS640M Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | Octal Bus Transceiver |
| Number of Data Channels | 8 channels |
| Width ng Data Bus | 8 bits |
| Communication Mode | Asynchronous, two-way |
| Direction Control | 1 DIR input |
| Output Enable | 1 active-low OE input |
| Power Supply | 5 V |
| Logic Family | 74LS low-power Schottky TTL |
| Hanay ng Temperature na Operasyon | 0 °C to 70 °C |
| Military Temperature Range | -55 °C to 125 °C for SN54LS64x versions |
| Packhaging | SOIC-20 (SOEIAJ-20) |
| Bilang ng Pin | 20 pins |
| Uri ng Pagpapasok | Surface Mount |
| High-Impedance Output Control | 8 outputs controlled by OE |
| AEC-Q100 Qualification | Not applicable |
Pin Configuration ng SN74LS640M
| Pin 1 | A1 — Data bus A input/output |
| Pin 2 | B1 — Data bus B input/output |
| Pin 3 | DIR — Direction control input |
| Pin 4 | A2 — Data bus A input/output |
| Pin 5 | B2 — Data bus B input/output |
| Pin 6 | A3 — Data bus A input/output |
| Pin 7 | B3 — Data bus B input/output |
| Pin 8 | GND — Ground |
| Pin 9 | B4 — Data bus B input/output |
| Pin 10 | A4 — Data bus A input/output |
| Pin 11 | OE — Active-low output-enable input |
| Pin 12 | B5 — Data bus B input/output |
| Pin 13 | A5 — Data bus A input/output |
| Pin 14 | B6 — Data bus B input/output |
| Pin 15 | A6 — Data bus A input/output |
| Pin 16 | B7 — Data bus B input/output |
| Pin 17 | A7 — Data bus A input/output |
| Pin 18 | B8 — Data bus B input/output |
| Pin 19 | A8 — Data bus A input/output |
| Pin 20 | VCC — Positive power supply |
Tipikal na mga Gamit
SN74LS640M ay nararapat para sa 6 aplikasyons: Bidirectional Processor Bus Interface, Memory Buffer Isolation, Peripheral Data Bus, Industrial Control Data Exchange, Legacy Test Equipment Interface, Data Acquisition Module.
Bidirectional Processor Bus Interface
The SN74LS640M fits a legacy processor bus when two eight-bit devices must exchange data over a shared parallel path. Its eight A-side and eight B-side paths support a complete byte per transfer, while DIR selects the active transmission direction. The active-low OE input can release the bus during reset or when another master takes control, reducing contention risk. Because the device belongs to the 5 V 74LS logic family, the associated processor must use compatible TTL thresholds, and the PCB should keep the device close to the bus source to limit propagation delay and loading.
Inirekomenda
Memory Buffer Isolation
The SN74LS640M can buffer a memory data bus when the processor and memory devices do not share identical drive timing or bus-turnaround requirements. Eight parallel channels preserve byte-oriented throughput, while DIR and OE allow the interface to be disabled during reset or test. The designer should confirm setup and hold timing against the memory device and account for the additional propagation delay introduced by the transceiver. Short traces, solid ground references, and direct VCC bypass are especially important because simultaneous eight-line transitions can increase bus activity and supply-current variation.
Inirekomenda
Peripheral Data Bus
The SN74LS640M is suitable for connecting an 8-bit peripheral controller to another bus segment when the design requires controlled direction changes and a high-impedance state. The DIR input selects which side drives, while OE provides a common isolation control for the output drivers. This makes the device useful in peripheral cards and legacy industrial controllers where multiple modules may share a wired bus. Validate signal levels, bus capacitance, and setup timing at the destination device, and route the control inputs away from switching-node and relay-control traces to prevent false direction changes.
Inirekomenda
Industrial Control Data Exchange
The SN74LS640M can serve as a bidirectional interface in legacy 5 V industrial-control equipment where separate control and field buses require isolation from bus contention. Its 8-bit width matches common parallel I/O arrangements, and the output-enable function permits controlled isolation during operating modes or maintenance procedures. The commercial SN74LS640 temperature range of 0 °C to 70 °C must remain within the enclosure's operating conditions; wider environmental requirements call for a device explicitly specified for the corresponding range. Use robust grounding and route direction and enable signals as slow-changing control nets.
Inirekomenda
Legacy Test Equipment Interface
The SN74LS640M is useful in legacy test and measurement equipment for routing an eight-bit instrument-control bus between a controller and a peripheral fixture. The transceiver consolidates eight data paths into one 20-pin device, reducing board area compared with separate buffers. DIR provides predictable source selection, while OE can place the peripheral side into a high-impedance state during fixture reset. Designers should preserve the voltage levels of the legacy test system, account for added bus delay, and verify that the enable state remains defined throughout power-up and power-down to avoid partially enabled bus contention.
Inirekomenda
Data Acquisition Module
The SN74LS640M can connect an acquisition module's eight-bit parallel control bus to a host processor through two shared bus segments. Eight data lines permit full-width command and status transfers, while DIR manages which module or host drives at a given time. The OE input allows the acquisition interface to disconnect during configuration changes and reduces loading on adjacent circuitry. Timing checks should include the transceiver's propagation delay, the host handshake interval, and the module's input setup requirements. Place the transceiver near the connector or module interface and provide a low-impedance ground plane to minimize noise coupling into the low-level TTL signals.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for SN74LS640M — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | SN74LS640MEL | SN74LS640-1NSR | SN74LS640NSRE4 | SN74LS640DW |
|---|---|---|---|---|---|
| Package | SOIC-20 (SOEIAJ-20) | SOIC-20 (SOEIAJ-20) | SOIC-20 | SOIC-20 | SOIC-20 |
| Brand | onsemi | onsemi | Texas Instruments | Texas Instruments | Texas Instruments |
| Function | Octal Bus Transceiver | Octal Bus Transceiver | Octal Bus Transceiver | Octal Bus Transceiver | Octal Bus Transceiver |
| Number of Data Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Data Bus Width | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits |
| Communication Mode | Asynchronous, two-way | Asynchronous, two-way | Asynchronous, two-way | Asynchronous, two-way | Asynchronous, two-way |
| Logic Family | 74LS low-power Schottky TTL | 74LS low-power Schottky TTL | 74LS low-power Schottky TTL | 74LS low-power Schottky TTL | 74LS low-power Schottky TTL |
| Output Enable | Active-low OE input | Active-low OE input | Active-low OE input | Active-low OE input | Active-low OE input |
| Pin Count | 20 pins | 20 pins | 20 pins | 20 pins | 20 pins |
Pangunahing mga Pagkakaiba
- Integrated octal direction and bus-isolation control (kumpara saSN74LS641)
- Documented terminal-compatible replacement route (kumpara saSN74LS640-1NSR)
- Surface-mount integration in the 20-pin SOIC footprint (kumpara saSN74LS640N)
Talaan ng Disenyo
Confirm the full transceiver truth table before substitution. The SN74LS640, SN74LS641, SN74LS642, and SN74LS645 family members differ in inversion and output-enable behavior, so an identical 20-pin footprint does not guarantee identical bus operation. Verify DIR polarity, OE polarity, input-to-output inversion, and the state of every output when OE is asserted. Also check the suffix-specific operating-temperature grade before approving a replacement in an existing design.
Place the SN74LS640M close to the bus connector or the device that owns the shared data path. Keep the eight parallel data traces short, matched in length where practical, and referenced by a continuous ground plane. Route DIR and OE away from clocks, relay coils, motor-control nodes, and switching-power connections. A clean control path reduces the chance that noise-derived timing violations cause two bus participants to drive simultaneously during turnaround.
Provide a stable 5 V supply and place the required VCC bypass capacitor close to the power pin with a short ground return. Eight simultaneous bus transitions can create dynamic current demand, so the supply must not sag enough to alter the TTL thresholds seen by connected devices. Use a solid ground reference, avoid sharing narrow return paths with high-current loads, and validate the power rail under worst-case bus activity rather than only at idle.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer family documentation identifies commercial and military temperature options, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration is stated for the exact SN74LS640M ordering code.