onsemi

SN74LS640M - Octal Bus Transceiver | onsemi | SOIC-20

MPN: SN74LS640M ✓ فعال
5 V Vdss SOIC-20 (SOEIAJ-20) Package
MOQ: 1 |

SN74LS640M جائزہ

The onsemi SN74LS640M is an octal bus transceiver designed for asynchronous, two-way communication between data buses, with eight data channels and a 20-pin SOIC-20 (SOEIAJ-20) package. It provides directional control for bus communication and an active-low output-enable function for placing the transceiver outputs in a high-impedance state when the bus is not being driven.

A bus transceiver is an interface-circuit category that connects two independently timed digital buses while adding direction and output control. The SN74LS640 belongs to the broader 74LS low-power Schottky TTL logic family, combining bidirectional data paths with bus-driver and bus-receiver functions. Its octal organization allows an entire eight-bit data word to be transferred between two buses through one 20-pin device.

The primary benefit of the SN74LS640M is integrated directional control. The DIR input determines the direction of data flow, while the output-enable input provides shared control over the eight output drivers. This arrangement reduces the number of external control gates and simplifies asynchronous system interfacing. Its octal structure also allows parallel processors, memory systems, peripheral controllers, and data-acquisition equipment to use one package for full-width bus buffering.

As a member of the SN54LS64x and SN74LS64x bus-transceiver family, the SN74LS640M is covered by the manufacturer's octal bus transceiver datasheet. That document also describes related SN74LS641, SN74LS642, SN74LS645, and military-temperature SN54LS64x devices. Because this is a low-power Schottky TTL device, system designers should preserve adequate input rise and fall times, maintain compatible VCC rails, and avoid excessive capacitive loading on the bus outputs.

Typical uses include bidirectional processor-bus isolation, memory-buffer interfaces, peripheral data buses, industrial control data exchange, and legacy digital test equipment. The transceiver is especially useful where two bus masters may alternate control of a shared eight-bit data path. The enable input can also isolate the device during reset, test, or bus turnaround, reducing contention risk when multiple sources share a conductive path.

PCB implementation should prioritize short, clean signal traces and a solid ground reference. Place the device close to the bus connector or processor interface, keep the DIR and output-enable traces away from high-current switching paths, and provide local bypass capacitance at VCC. Confirm that the connected devices use compatible TTL signal levels and that the enabled direction matches the intended source and destination buses.

This page consolidates the device function, package details, operating context, design guidance, and documented replacement options into one engineering reference. It also identifies where compatibility must be checked against pinout, power requirements, timing, and lifecycle constraints before approving a substitute for an existing design.

کے لیے ڈراپ اِن متبادل SN74LS640M — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

SN74LS640MEL

✅ ڈراپ-اِن
📦 SOIC-20 (SOEIAJ-20)
Same 20-pin footprint and transceiver function; ordering suffix differs with 0 pin assignments changed.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

SN74LS640-1NSR

✅ ڈراپ-اِن
📦 SOIC-20 (SOEIAJ-20)
Same 20-terminal footprint and core transceiver ratings; no published voltage or pinout change is indicated in the cross-reference result.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

SN74LS640NSRE4

✅ ڈراپ-اِن
📦 SOIC-20 (SOEIAJ-20)
Same 20-terminal footprint and core transceiver ratings; no published voltage or pinout change is indicated in the cross-reference result.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

SN74LS640DW

✅ ڈراپ-اِن
📦 SOIC-20 (SOEIAJ-20)
Same 20-pin SOIC footprint and transceiver function; ordering-code terms differ with 0 pin assignments changed.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

SN74LS640M زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Product Type Octal Bus Transceiver
Number of Data Channels 8 channels
ڈیٹا بس چوڑائی 8 bits
Communication Mode Asynchronous, two-way
Direction Control 1 DIR input
Output Enable 1 active-low OE input
Power Supply 5 V
Logic Family 74LS low-power Schottky TTL
آپریٹنگ درجہ حرارت رینج 0 °C to 70 °C
Military Temperature Range -55 °C to 125 °C for SN54LS64x versions
پیکیج SOIC-20 (SOEIAJ-20)
پن کی تعداد 20 pins
ماؤنٹنگ ٹائپ Surface Mount
High-Impedance Output Control 8 outputs controlled by OE
AEC-Q100 Qualification Not applicable

SN74LS640M پن کنفیگریشن

SOIC-20 Package Pinout Diagram SOIC-20W 20-pin, 7.5x12.8mm, P1.27mm, JEDEC MS-013. 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 SOIC-20
پن 1 A1 — Data bus A input/output
پن 2 B1 — Data bus B input/output
پن 3 DIR — Direction control input
پن 4 A2 — Data bus A input/output
پن 5 B2 — Data bus B input/output
پن 6 A3 — Data bus A input/output
پن 7 B3 — Data bus B input/output
پن 8 GND — Ground
پن 9 B4 — Data bus B input/output
پن 10 A4 — Data bus A input/output
پن 11 OE — Active-low output-enable input
پن 12 B5 — Data bus B input/output
پن 13 A5 — Data bus A input/output
پن 14 B6 — Data bus B input/output
پن 15 A6 — Data bus A input/output
پن 16 B7 — Data bus B input/output
پن 17 A7 — Data bus A input/output
پن 18 B8 — Data bus B input/output
پن 19 A8 — Data bus A input/output
پن 20 VCC — Positive power supply

عام استعمالات

SN74LS640M کے لیے موزوں ہے 6 ایپلیکیشنs: Bidirectional Processor Bus Interface, Memory Buffer Isolation, Peripheral Data Bus, Industrial Control Data Exchange, Legacy Test Equipment Interface, Data Acquisition Module.

🖥️

Bidirectional Processor Bus Interface

The SN74LS640M fits a legacy processor bus when two eight-bit devices must exchange data over a shared parallel path. Its eight A-side and eight B-side paths support a complete byte per transfer, while DIR selects the active transmission direction. The active-low OE input can release the bus during reset or when another master takes control, reducing contention risk. Because the device belongs to the 5 V 74LS logic family, the associated processor must use compatible TTL thresholds, and the PCB should keep the device close to the bus source to limit propagation delay and loading.

🖥️

Memory Buffer Isolation

The SN74LS640M can buffer a memory data bus when the processor and memory devices do not share identical drive timing or bus-turnaround requirements. Eight parallel channels preserve byte-oriented throughput, while DIR and OE allow the interface to be disabled during reset or test. The designer should confirm setup and hold timing against the memory device and account for the additional propagation delay introduced by the transceiver. Short traces, solid ground references, and direct VCC bypass are especially important because simultaneous eight-line transitions can increase bus activity and supply-current variation.

🏭

Peripheral Data Bus

The SN74LS640M is suitable for connecting an 8-bit peripheral controller to another bus segment when the design requires controlled direction changes and a high-impedance state. The DIR input selects which side drives, while OE provides a common isolation control for the output drivers. This makes the device useful in peripheral cards and legacy industrial controllers where multiple modules may share a wired bus. Validate signal levels, bus capacitance, and setup timing at the destination device, and route the control inputs away from switching-node and relay-control traces to prevent false direction changes.

🏭

Industrial Control Data Exchange

The SN74LS640M can serve as a bidirectional interface in legacy 5 V industrial-control equipment where separate control and field buses require isolation from bus contention. Its 8-bit width matches common parallel I/O arrangements, and the output-enable function permits controlled isolation during operating modes or maintenance procedures. The commercial SN74LS640 temperature range of 0 °C to 70 °C must remain within the enclosure's operating conditions; wider environmental requirements call for a device explicitly specified for the corresponding range. Use robust grounding and route direction and enable signals as slow-changing control nets.

🔧

Legacy Test Equipment Interface

The SN74LS640M is useful in legacy test and measurement equipment for routing an eight-bit instrument-control bus between a controller and a peripheral fixture. The transceiver consolidates eight data paths into one 20-pin device, reducing board area compared with separate buffers. DIR provides predictable source selection, while OE can place the peripheral side into a high-impedance state during fixture reset. Designers should preserve the voltage levels of the legacy test system, account for added bus delay, and verify that the enable state remains defined throughout power-up and power-down to avoid partially enabled bus contention.

📡

Data Acquisition Module

The SN74LS640M can connect an acquisition module's eight-bit parallel control bus to a host processor through two shared bus segments. Eight data lines permit full-width command and status transfers, while DIR manages which module or host drives at a given time. The OE input allows the acquisition interface to disconnect during configuration changes and reduces loading on adjacent circuitry. Timing checks should include the transceiver's propagation delay, the host handshake interval, and the module's input setup requirements. Place the transceiver near the connector or module interface and provide a low-impedance ground plane to minimize noise coupling into the low-level TTL signals.

تجویز کردہ پروڈکٹس کا خلاصہ

SN74LS640 Base octal bus-transceiver ordering option استعمال ہوتا ہے: Bidirectional Processor Bus Interface, Memory Buffer Isolation, Peripheral Data Bus, Industrial Control Data Exchange, Legacy Test Equipment Interface, Data Acquisition Module SN74LS645 Related family member with different output-enable polarity استعمال ہوتا ہے: Bidirectional Processor Bus Interface, Legacy Test Equipment Interface SN74LS642 Related family member for alternative enable polarity استعمال ہوتا ہے: Memory Buffer Isolation, Data Acquisition Module SN74LS641 Related family member with different inversion configuration استعمال ہوتا ہے: Peripheral Data Bus SN54LS640 Military-temperature counterpart in the same transceiver family استعمال ہوتا ہے: Industrial Control Data Exchange
What is the SN74LS640M used for?
The SN74LS640M is an octal bus transceiver used for asynchronous, two-way communication between two eight-bit data buses. According to the onsemi octal bus transceiver datasheet, its eight data channels are controlled by DIR and output-enable inputs. This makes the device suitable for connecting processor, memory, peripheral, or industrial-control buses that need controlled bidirectional data transfer without contention.
What is the SN74LS640M package and pin count?
The SN74LS640M uses the 20-pin SOIC-20 package, identified as SOEIAJ-20 in the manufacturer documentation. The surface-mount package provides eight bidirectional data pins, a direction-control input, an output-enable input, power, and ground. Use the package drawing and pin-description table in the onsemi datasheet when assigning PCB tracks and checking land-pattern orientation.
How does the DIR pin control SN74LS640M operation?
The DIR input determines the direction in which data moves through the eight transceiver channels. Together with the output-enable input, DIR allows the device to be connected to two buses and to reverse the transfer direction without changing the physical wiring. According to the onsemi octal bus transceiver datasheet, these controls are intended to minimize external timing requirements during asynchronous bus communication.
What does the active-low OE input do on the SN74LS640M?
The active-low OE input places all eight transceiver outputs in the high-impedance state when it is asserted, allowing the connected buses to be released. When OE is deasserted and DIR is valid, the outputs actively drive the selected data direction. This bus-isolation function is useful during reset, test modes, bus turnaround, and systems in which more than one source may share a bus.
Where can I download the SN74LS640M datasheet PDF?
The SN74LS640M datasheet PDF is available from the onsemi document hosted at the product datasheet URL on this page. The manufacturer document provides the octal bus-transceiver description, SOEIAJ-20 package drawing, pin assignments, electrical characteristics, and timing information. Use the pin-description table and recommended operating conditions when designing or qualifying a replacement.
Where can I find the SN74LS640M pinout?
The SN74LS640M pinout is presented in the onsemi octal bus transceiver datasheet, whose package is identified as SOEIAJ-20. The 20-pin arrangement contains eight data positions labeled A1 through A8 and B1 through B8, plus DIR, OE, VCC, and GND. Use the manufacturer pin-description table to assign tracks and verify that pin 1 orientation matches the PCB footprint.
What is the difference between SN74LS640M and SN74LS640DW?
The SN74LS640M and SN74LS640DW implement the octal bus-transceiver function in the 20-pin SOIC-20 class of package, but their ordering codes can carry different manufacturer, temperature, qualification, or commercial terms. The SN74LS640-1NSR and SN74LS640NSRE4 TI devices likewise appear in the documented cross-reference results as terminal- and package-consistent options. Verify the suffix-specific operating range and procurement status before production substitution.
When should I choose SN74LS640M over another 74LS transceiver?
Choose the SN74LS640M when the design needs a non-inverting octal bus transceiver with DIR and output-enable control in a 20-pin SOIC package. The related SN74LS641, SN74LS642, and SN74LS645 devices provide different inversion or output-enable arrangements, so their truth tables must be checked before replacement. The SN74LS640M is appropriate when its documented directional behavior matches the intended bus protocol.
Is the SN74LS640M suitable for industrial-control bus interfaces?
The SN74LS640M can support legacy 5 V industrial-control and peripheral data-bus interfaces when signal levels, timing, and environmental requirements match the device. Its documented commercial operating range is 0 °C to 70 °C, while military SN54LS64x versions cover -55 °C to 125 °C. For wider-temperature industrial equipment, select the temperature grade explicitly stated for the application.
What is the best drop-in replacement for SN74LS640M?
The best drop-in replacement is the documented option that preserves the 20-pin SOIC footprint, pin assignments, voltage, and transceiver truth table. Cross-reference information identifies TI SN74LS640-1NSR and SN74LS640NSRE4 as terminal- and package-consistent alternatives, while SN74LS640DW is another 20-pin SOIC ordering option. Confirm suffix-specific temperature, lifecycle, and timing requirements before approving any substitute.
Can SN74LS640-1NSR replace SN74LS640M?
The SN74LS640-1NSR can be considered for replacement when its complete ordering details satisfy the original design requirements. The cross-reference result describes the SN74LS640-1NSR and SN74LS640NSRE4 devices as functionally and terminally consistent with the SN74LS640M, with the packages matching. Review the manufacturer datasheet for voltage, temperature, propagation timing, enable logic, and lifecycle before production use.
What are the key specifications of SN74LS640M that engineers should know?
The SN74LS640M is a 5 V, eight-channel, 74LS-family bus transceiver in a 20-pin SOIC-20 package. Its main engineering characteristics are asynchronous two-way operation, DIR-controlled direction, active-low output enable, and access to eight A-side and eight B-side data pins. The manufacturer documentation also identifies the commercial temperature range as 0 °C to 70 °C for SN74LS640-series devices.
What can replace an SN74LS640M in an asynchronous bus design?
A replacement for the SN74LS640M must provide the same 20-pin SOIC footprint, compatible 5 V operation, matching DIR and OE behavior, and the required data truth table. SN74LS640-1NSR and SN74LS640NSRE4 are documented as package- and terminal-consistent options, and SN74LS640DW provides another 20-pin SOIC ordering route. Also verify propagation delay, bus-loading capability, temperature range, and current lifecycle status.
Where can I buy SN74LS640M and request a quote?
Use the Request a Quote form on this page to request current SN74LS640M availability, pricing, minimum order quantity, and lead time. The form is the appropriate route for a quote based on the exact MPN, package, quantity, and delivery requirements. Request separate quotes for production quantities, prototype quantities, and any scheduled multi-year deliveries so the manufacturer can confirm allocation accurately.
How long is the lead time for SN74LS640M?
The current lead time for SN74LS640M should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, package configuration, manufacturing status, and production schedule, so a generic figure would not reliably represent the exact order. Include your required quantity, date code requirements, target delivery date, and approved alternate suffix in the request.

کے لیے انجینئرنگ ریفرنس ڈیٹا SN74LS640M — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the SN74LS640M when a legacy 5 V system needs an eight-channel, non-inverting bidirectional bus transceiver with DIR selection and active-low output enable in a 20-pin SOIC package. It is appropriate when two bus segments require controlled direction changes or high-impedance isolation. Use SN74LS640-1NSR or SN74LS640NSRE4 when a documented terminal-compatible TI source is preferred, but verify operating temperature, lifecycle, and qualification for the exact suffix. Consider SN74LS640MEL for onsemi sourcing continuity. Do not substitute SN74LS641, SN74LS642, or SN74LS645 solely by package match: their inversion and enable-polarity configurations differ and can reverse data or alter bus ownership. Before any replacement, compare pin assignments, DIR truth table, OE behavior, propagation delay, supply current, and capacitive loading against the original design.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ SN74LS640MEL SN74LS640-1NSR SN74LS640NSRE4 SN74LS640DW
Package SOIC-20 (SOEIAJ-20) SOIC-20 (SOEIAJ-20) SOIC-20 SOIC-20 SOIC-20
Brand onsemi onsemi Texas Instruments Texas Instruments Texas Instruments
Function Octal Bus Transceiver Octal Bus Transceiver Octal Bus Transceiver Octal Bus Transceiver Octal Bus Transceiver
Number of Data Channels 8 channels 8 channels 8 channels 8 channels 8 channels
Data Bus Width 8 bits 8 bits 8 bits 8 bits 8 bits
Communication Mode Asynchronous, two-way Asynchronous, two-way Asynchronous, two-way Asynchronous, two-way Asynchronous, two-way
Logic Family 74LS low-power Schottky TTL 74LS low-power Schottky TTL 74LS low-power Schottky TTL 74LS low-power Schottky TTL 74LS low-power Schottky TTL
Output Enable Active-low OE input Active-low OE input Active-low OE input Active-low OE input Active-low OE input
Pin Count 20 pins 20 pins 20 pins 20 pins 20 pins

اہم امتیازی خصوصیات

  • Integrated octal direction and bus-isolation control (بمقابلہSN74LS641)
  • Documented terminal-compatible replacement route (بمقابلہSN74LS640-1NSR)
  • Surface-mount integration in the 20-pin SOIC footprint (بمقابلہSN74LS640N)

ڈیزائن نوٹس

Confirm the full transceiver truth table before substitution. The SN74LS640, SN74LS641, SN74LS642, and SN74LS645 family members differ in inversion and output-enable behavior, so an identical 20-pin footprint does not guarantee identical bus operation. Verify DIR polarity, OE polarity, input-to-output inversion, and the state of every output when OE is asserted. Also check the suffix-specific operating-temperature grade before approving a replacement in an existing design.

Place the SN74LS640M close to the bus connector or the device that owns the shared data path. Keep the eight parallel data traces short, matched in length where practical, and referenced by a continuous ground plane. Route DIR and OE away from clocks, relay coils, motor-control nodes, and switching-power connections. A clean control path reduces the chance that noise-derived timing violations cause two bus participants to drive simultaneously during turnaround.

Provide a stable 5 V supply and place the required VCC bypass capacitor close to the power pin with a short ground return. Eight simultaneous bus transitions can create dynamic current demand, so the supply must not sag enough to alter the TTL thresholds seen by connected devices. Use a solid ground reference, avoid sharing narrow return paths with high-current loads, and validate the power rail under worst-case bus activity rather than only at idle.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The manufacturer family documentation identifies commercial and military temperature options, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration is stated for the exact SN74LS640M ordering code.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-18 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

SN74LS640M datasheet SN74LS640M datasheet pdf SN74LS640M pinout SN74LS640M equivalent SN74LS640M replacement SN74LS640M drop-in replacement SN74LS640M price SN74LS640M stock onsemi SN74LS640M SN74LS640M vs SN74LS645 SN74LS640M SOIC-20 footprint SN74LS640M bidirectional bus interface

متعلقہ اجزاء اور اصطلاحات

onsemi SN74LS640M SN74LS640MEL SN74LS640-1NSR SN74LS640NSRE4 SN74LS640DW Texas Instruments Octal Bus Transceiver bus transceiver bidirectional data bus 74LS low-power Schottky TTL asynchronous communication DIR control input active-low output enable high-impedance output SOIC-20 SOEIAJ-20 surface mount SMD logic IC semiconductor industrial control data acquisition legacy computer bus
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں