Texas Instruments

SN75172N - 4-Channel RS-485 Driver | Texas Instruments

MPN: SN75172N ✓ Nakahanda
4.75 V to 5.25 V Vdss ANSI EIA/TIA-422-B and ITU Recommendation V.11 Rds(on) 16-pin PDIP Package
MOQ: 1 |

SN75172N Ulas

Texas Instruments SN75172N is a monolithic quadruple differential line driver with four 3-state outputs, a 4.75 V to 5.25 V supply range, and operation at rates up to 4 megabaud. The device is packaged in a 16-pin PDIP and is designed for balanced multipoint transmission on long bus lines in noisy environments. Its four channels support RS-422, RS-485, EIA/TIA-422-B, and ITU-T V.11-compatible interfaces.

A differential line driver is a type of interface transceiver component that converts a digital logic signal into a balanced differential output. It belongs to the interface IC hierarchy, where line drivers are used with line receivers to form robust communications links over cables or backplanes. Balanced signaling reduces susceptibility to common-mode interference, while 3-state outputs allow multiple devices to share a bus when they are not actively transmitting.

The SN75172 provides four independent differential driver channels in one package. Each channel can be placed in a high-impedance state to permit party-line operation, and the wide positive and negative common-mode output voltage ranges support noisy multipoint networks. Operation up to 4 megabaud makes the device suitable for industrial control, instrumentation, communications, and data-acquisition systems using balanced differential buses.

Technically, each driver translates complementary TTL-compatible input states into a differential output. The true differential outputs support current-mode signaling, while the three-state outputs provide bus-enable control without requiring a separate bus driver. Because the SN75172N is a driver-only device, a receiving node requires a compatible differential receiver or transceiver elsewhere in the system.

Typical implementations include four isolated or non-isolated RS-485 transmitters, factory automation links, test and measurement equipment, industrial peripheral interfaces, and point-to-point RS-422 links. In each case, the system must preserve the differential pair routing, provide a correctly sized termination strategy, and account for common-mode voltage at the cable interface.

A key design consideration is that the SN75172N is intended for a 4.75 V to 5.25 V supply and does not provide galvanic isolation. Designers should use a suitable regulated supply, route each differential pair as a tightly coupled pair, and protect exposed bus connectors as required by the installation environment. Enable polarity and timing should be checked against the system requirement before sharing a party-line bus.

This page organizes the manufacturer's principal electrical and interface characteristics with design guidance, application context, package information, and replacement guidance. It also distinguishes driver-only devices from combined transceivers and receivers so that board-level replacements are evaluated for actual pin and functional compatibility rather than broad RS-485 similarity.

Mga alternatibo na pwedeng ilagay na SN75172N — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

SN75114NE4

✅ Drop-In
📦 16-pin PDIP
Related quadruple differential line-driver family; pin, timing, and output-function compatibility require confirmation against the SN75172N datasheet.

📋 Alternatibo na Reference (hindi sa katalogo)

SN75176BPE4

✅ Drop-In
📦 16-pin PDIP
Related TI differential interface family; the available comparison identifies different receiver-oriented functionality, so pin-level compatibility must be verified.

📋 Alternatibo na Reference (hindi sa katalogo)

SN75172N Mga Spesipikasyon

Product Type Quadruple differential line driver
Driver Channel Count 4 channels
Receiver Channel Count 0 channels
Type ng Output 3-state differential outputs
Supply Voltage Range 4.75 V to 5.25 V
Maximum Data Rate 4 megabaud
Supported Interfaces RS-422 and RS-485
Standards Compatibility ANSI EIA/TIA-422-B and ITU Recommendation V.11
Packhaging 16-pin PDIP
Uri ng Pagpapasok Through-hole
Isolation None

Gabay sa Pin Configuration ng SN75172N 16-pin pdip

Pin configuration para sa SN75172N (16-pin pdip package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.

Pinout diagram ng 16-pin pdip package para sa SN75172N

Wala ng detalyadong pinout data na magagamit para sa SN75172N.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

SN75172N ay nararapat para sa 6 aplikasyons: Industrial RS-485 Transmitter, RS-422 Point-to-Point Links, Factory Automation Bus Interface, Test and Measurement Front End, Data Acquisition Equipment, Communications Peripherals.

🏭

Industrial RS-485 Transmitter

The SN75172N is well suited to an industrial RS-485 transmitter because it provides four 3-state differential driver channels from a 4.75 V to 5.25 V supply and supports rates up to 4 megabaud. Each channel can be enabled selectively, allowing one node at a time to drive a party-line bus while the other outputs remain high impedance. The implementation should use tightly coupled differential routing, appropriate bus termination, and connector-level surge protection. Because the SN75172N has no galvanic isolation, long external cables may require a separate isolation strategy.

🌐

RS-422 Point-to-Point Links

For RS-422 point-to-point communication, the SN75172N can provide four balanced differential transmitters with independent 3-state control. Texas Instruments identifies the SN75172 as compliant with the requirements of EIA/TIA-422-B and ITU-T V.11, while its balanced outputs reduce sensitivity to noise picked up between the conductors. Keep each driver-to-receiver pair routed together, terminate the receiving end as required by the system architecture, and verify that only one source drives a differential pair at a time.

🤖

Factory Automation Bus Interface

The four-channel SN75172N fits factory automation equipment that distributes multiple differential command or data signals between a controller and remote modules. Its 4 megabaud capability provides ample link-rate margin for common industrial message traffic, while 3-state outputs support shared-bus implementations. Designers should account for reflected signals on long cables, maintain consistent reference ground within the installation, and add external protection when the bus leaves an enclosure. The 16-pin PDIP package also simplifies inspection and repair in legacy industrial control systems.

🔧

Test and Measurement Front End

Instrumentation systems can use the SN75172N to send control and status information across balanced links between instrument modules, computers, or service equipment. Differential signaling is useful when cables pass near motors, switching supplies, or other industrial noise sources, and the three-state outputs allow bus sharing when required. For accurate measurements, keep the data path separate from sensitive analog inputs and place termination at the physical endpoints. The transmitter must also be paired with a receiver whose input thresholds and common-mode range match the intended RS-422 or RS-485 network.

📊

Data Acquisition Equipment

The SN75172N can supply four balanced command or digital-data channels in a multi-channel data-acquisition system. Its four independent drivers reduce the number of separate transmitter packages required when the acquisition chassis communicates with external sensors, fixtures, or controllers. Up to 4 megabaud operation supports practical telemetry rates, but command-response protocols should include acknowledgments or timeouts to recover from bus contention. External termination, grounding, and protection requirements depend on cable length and topology and should be validated in the assembled system.

📡

Communications Peripherals

The SN75172N is applicable to communications peripherals that transmit only, such as outbound sensor hubs, remote I/O modules, and controller interfaces. Four 3-state differential channels provide flexible enable control, allowing the system to support point-to-point links or a party-line arrangement. The 4.75 V to 5.25 V operating range aligns with conventional 5 V logic systems, while the 16-pin PDIP format supports through-hole construction. Designers should use separate receive channels and avoid confusing this driver-only IC with a full RS-485 transceiver.

What is the SN75172N?
The SN75172N is a Texas Instruments monolithic quadruple differential line driver with four 3-state outputs. According to the TI product page, it supports balanced multipoint transmission at rates up to 4 megabaud and is designed for EIA/TIA-422-B, RS-485, and ITU-T V.11 applications. The SN75172N provides driver channels only; it does not include receiver channels.
What are the key specifications of SN75172N that engineers should know?
The SN75172N integrates four differential driver channels with 3-state outputs, operates from a 4.75 V to 5.25 V supply, and supports transmission rates up to 4 megabaud. According to the TI product page and product listing, the device is intended for EIA/TIA-422-B, RS-485, and ITU-T V.11-compatible balanced multipoint systems. Its 16-pin PDIP package supports through-hole board assembly.
Is SN75172N an RS-485 transceiver or only a driver?
The SN75172N is only an RS-485 and RS-422 line driver, not a full transceiver. It contains four differential driver channels and no receiver channels. According to Texas Instruments, each driver has a 3-state output for party-line operation. A separate receiver or transceiver is therefore required whenever the equipment must receive data from the bus.
Where can I download the SN75172N datasheet PDF?
The official SN75172N datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/sn75172.pdf. The manufacturer product page is also available at https://www.ti.com/product/SN75172. Use the manufacturer's pin-description table when assigning signals and verify the electrical limits, enable timing, and recommended application circuit before releasing a PCB design.
Where can I find the SN75172N pinout?
The SN75172N pinout is contained in the Texas Instruments SN75172 datasheet and corresponds to the device's 16-pin PDIP package. Use the pin-description table in the manufacturer datasheet to identify input, output, enable, and supply pins. The SN75172N uses a through-hole PDIP package, and no exposed pad or additional hidden thermal connection is required.
What is the maximum data rate of SN75172N?
The SN75172N supports balanced multipoint transmission at rates up to 4 megabaud. According to the Texas Instruments product page, the device is optimized for RS-422 and RS-485 communication over long bus lines in noisy environments. Actual system throughput can be lower because protocol overhead, cable length, terminations, reflections, and grounding also influence reliable bus performance.
Which supply voltage does SN75172N require?
The SN75172N operates from a 4.75 V to 5.25 V supply, making it a 5 V interface device. Texas Instruments describes the IC as a quadruple differential line driver with 3-state outputs. A regulated 5 V rail must remain within this range, and supply bypassing should be placed close to the device's supply and ground pins to limit transient coupling into the bus outputs.
Can SN75172N drive an RS-485 party-line bus?
Yes, the SN75172N can support an RS-485 party-line arrangement when only one transmitter is enabled at a time. Its four differential outputs have 3-state operation, allowing inactive drivers to present a high-impedance state rather than fighting an active node. According to the TI product page, the wide positive and negative common-mode output ranges suit balanced multipoint transmission in noisy environments.
What is the best drop-in replacement for SN75172N?
The SN75172N should be replaced only with a four-channel differential driver that has the same 16-pin PDIP pinout, compatible enable logic, and electrical ratings. No alternative in the retrieved cross-reference results is confirmed as a pin-compatible drop-in replacement, so SN75ALS172N should be evaluated against the TI datasheets rather than treated as automatic. Do not substitute a receiver-only part or a combined transceiver without redesigning the interface.
What can replace SN75172N on an existing PCB?
An existing PCB can accept a replacement only when the candidate has the same 16-pin PDIP footprint, identical pin functions, equivalent 5 V supply requirements, compatible 3-state enable timing, and comparable output drive. The retrieved cross-reference material identifies SN75ALS172N as a related TI part, but it does not establish complete pin compatibility. Verify both datasheets before committing it as a drop-in replacement.
Is SN75172N the same as SN75175N?
No. The SN75172N is a quadruple differential line driver, while the SN75175N is described in the retrieved comparison material as a quadruple differential line receiver. Although both relate to balanced multipoint communications, they perform opposite signal-chain functions and should not be considered interchangeable. Replacing the SN75172N with SN75175N would require a different interface strategy and would not preserve the transmitter function.
SN75172N vs SN75176BPE4 - which is better for a driver-only bus?
The SN75172N is the better match when the PCB specifically needs four 3-state differential driver channels, because it is a dedicated line driver. SN75176BPE4 is a combined interface device rather than an equivalent driver-only footprint, so it is not a drop-in substitute for the SN75172N. The retrieved comparison confirms that these are distinct device types; use the SN75172N when transmitter-only operation is required.
When should I choose SN75172N over a combined RS-485 transceiver?
Choose the SN75172N when a board must transmit on four balanced channels but receives through a separate receiver subsystem. Its dedicated 3-state differential outputs support both point-to-point and party-line transmitter arrangements at rates up to 4 megabaud. A combined transceiver can simplify a design that needs both directions in one package, but it is not a functional drop-in replacement for a transmitter-only PCB.
Is SN75172N suitable for industrial RS-485 equipment?
The SN75172N is architecturally suitable for industrial balanced multipoint links because it supports RS-485, RS-422, and ITU-T V.11 requirements at up to 4 megabaud. The device itself has no galvanic isolation, so an industrial installation still needs appropriate surge, ESD, grounding, and isolation arrangements. Confirm its specified temperature range and protection requirements against the installation environment before production use.
Where can I buy SN75172N and what is its current lead time?
Use the Request a Quote form on this page to obtain current SN75172N availability, commercial terms, and lead-time confirmation for the exact 16-pin PDIP ordering configuration. The distributor listings confirm the exact MPN, but they do not provide a machine-readable quantity-price table or a fixed production lead time. Buyers should avoid relying on cached stock messages when planning a multi-year production run.

Impormasyon ng Talumpati sa Engineering for SN75172N — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the SN75172N when the board needs four 3-state differential transmitters and reception is handled elsewhere. Its 4.75 V to 5.25 V supply, operation up to 4 megabaud, and support for EIA/TIA-422-B, RS-485, and ITU-T V.11 interfaces suit balanced industrial, instrumentation, and communications links. Do not select a receiver-only device when transmission is required, and do not expect a combined transceiver to be a pin-compatible substitute. If a replacement is needed for an existing 16-pin PDIP board, verify the candidate's pin functions, enable polarity, output drive, timing, and common-mode limits against the manufacturer datasheets. For long external cables or high-noise installations, add appropriate protection and isolation because the SN75172N provides neither galvanic isolation nor a complete surge-protection solution.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto
Product Type Quadruple differential line driver
Driver Channels 4
Receiver Channels 0
Output State Control 3-state
Supply Voltage 4.75 V to 5.25 V
Maximum Data Rate 4 megabaud
Interface Standards EIA/TIA-422-B, RS-485, and ITU-T V.11
Package 16-pin PDIP
Brand Texas Instruments

Pangunahing mga Pagkakaiba

  • Four independently usable 3-state transmitter channels (kumpara saSN75175N)
  • Dedicated multipoint transmitter architecture (kumpara saSN75176BPE4)
  • Four megabaud balanced multipoint operation (kumpara saSN75175N)

Talaan ng Disenyo

Route every differential output as a tightly coupled pair with continuous reference-plane support. Keep the two conductors of a channel together, match their geometry as closely as practical, and avoid routing one conductor around clocks, relays, or switching-power nodes. Place termination components at the physical bus endpoints rather than beside every driver, because excessive termination lowers the loaded bus impedance and can increase driver stress.

Decouple the 4.75 V to 5.25 V supply close to the SN75172N power and ground pins using the capacitance and placement specified in the TI application guidance. Keep the ground connection short and place it in the same return path as the outputs. Verify that the supply remains within tolerance during bus enable transitions because an undersized rail can cause differential output asymmetry, false data reception, or unexpected driver operation.

Do not enable multiple SN75172N channels onto the same bus pair at the same time. The 3-state outputs are intended to support multipoint communication, not simultaneous contention. Likewise, do not substitute a receiver-only IC such as the SN75175N for this transmitter-only device. Confirm enable polarity, output impedance, propagation timing, and common-mode limits against the TI datasheet before modifying a production board.

Treat external RS-422 and RS-485 connections as noisy cable ports even when the IC itself is a logic device. Use controlled-rise-time protection networks or external transceivers where surge and ESD requirements exceed the SN75172N's internal capabilities. Maintain a coherent ground reference along the installation and avoid long unprotected stubs, because these practices reduce common-mode excursions and improve reliability in electrically noisy installations.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The retrieved manufacturer and distributor material does not explicitly state the compliance status for SN75172N.

Kaugnay na Hanapin

sn75172 spice SN75172N datasheet SN75172N pinout SN75172N datasheet pdf SN75172N equivalent SN75172N replacement SN75172N vs SN75175N SN75172N vs SN75176BPE4 SN75172N 4 megabaud SN75172N RS-485 driver SN75172N 16-pin PDIP Texas Instruments SN75172N

Mga kaugnay na Mga Komponente at mga Tuntunin

Texas Instruments SN75172N SN75172 SN75175N SN75176BPE4 SN75ALS172N differential line driver RS-485 RS-422 EIA/TIA-422-B ITU-T V.11 quadruple line driver balanced multipoint transmission 3-state output high-impedance state line transceiver interface IC semiconductor 16-pin PDIP through-hole package common-mode voltage megabaud 5 V logic industrial automation data acquisition
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ