SN75172N - 4-Channel RS-485 Driver | Texas Instruments
料号: SN75172N ✓ 量产中SN75172N 概述
A differential line driver is a type of interface transceiver component that converts a digital logic signal into a balanced differential output. It belongs to the interface IC hierarchy, where line drivers are used with line receivers to form robust communications links over cables or backplanes. Balanced signaling reduces susceptibility to common-mode interference, while 3-state outputs allow multiple devices to share a bus when they are not actively transmitting.
The SN75172 provides four independent differential driver channels in one package. Each channel can be placed in a high-impedance state to permit party-line operation, and the wide positive and negative common-mode output voltage ranges support noisy multipoint networks. Operation up to 4 megabaud makes the device suitable for industrial control, instrumentation, communications, and data-acquisition systems using balanced differential buses.
Technically, each driver translates complementary TTL-compatible input states into a differential output. The true differential outputs support current-mode signaling, while the three-state outputs provide bus-enable control without requiring a separate bus driver. Because the SN75172N is a driver-only device, a receiving node requires a compatible differential receiver or transceiver elsewhere in the system.
Typical implementations include four isolated or non-isolated RS-485 transmitters, factory automation links, test and measurement equipment, industrial peripheral interfaces, and point-to-point RS-422 links. In each case, the system must preserve the differential pair routing, provide a correctly sized termination strategy, and account for common-mode voltage at the cable interface.
A key design consideration is that the SN75172N is intended for a 4.75 V to 5.25 V supply and does not provide galvanic isolation. Designers should use a suitable regulated supply, route each differential pair as a tightly coupled pair, and protect exposed bus connectors as required by the installation environment. Enable polarity and timing should be checked against the system requirement before sharing a party-line bus.
This page organizes the manufacturer's principal electrical and interface characteristics with design guidance, application context, package information, and replacement guidance. It also distinguishes driver-only devices from combined transceivers and receivers so that board-level replacements are evaluated for actual pin and functional compatibility rather than broad RS-485 similarity.
直接替换替代料: SN75172N ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
SN75114NE4
✅ 直接替换📋 参考替代料(不在目录中)
SN75176BPE4
✅ 直接替换📋 参考替代料(不在目录中)
SN75172N 规格参数
| Product Type | Quadruple differential line driver |
| Driver Channel Count | 4 channels |
| Receiver Channel Count | 0 channels |
| 输出类型 | 3-state differential outputs |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Maximum Data Rate | 4 megabaud |
| Supported Interfaces | RS-422 and RS-485 |
| Standards Compatibility | ANSI EIA/TIA-422-B and ITU Recommendation V.11 |
| 封装 | 16-pin PDIP |
| 安装类型 | Through-hole |
| Isolation | None |
SN75172N 16-pin pdip 引脚配置指南
SN75172N(16-pin pdip 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: SN75172N.
请参阅 数据手册 以查看完整引脚配置。
典型应用
SN75172N 适用于 6 应用s: Industrial RS-485 Transmitter, RS-422 Point-to-Point Links, Factory Automation Bus Interface, Test and Measurement Front End, Data Acquisition Equipment, Communications Peripherals.
Industrial RS-485 Transmitter
The SN75172N is well suited to an industrial RS-485 transmitter because it provides four 3-state differential driver channels from a 4.75 V to 5.25 V supply and supports rates up to 4 megabaud. Each channel can be enabled selectively, allowing one node at a time to drive a party-line bus while the other outputs remain high impedance. The implementation should use tightly coupled differential routing, appropriate bus termination, and connector-level surge protection. Because the SN75172N has no galvanic isolation, long external cables may require a separate isolation strategy.
RS-422 Point-to-Point Links
For RS-422 point-to-point communication, the SN75172N can provide four balanced differential transmitters with independent 3-state control. Texas Instruments identifies the SN75172 as compliant with the requirements of EIA/TIA-422-B and ITU-T V.11, while its balanced outputs reduce sensitivity to noise picked up between the conductors. Keep each driver-to-receiver pair routed together, terminate the receiving end as required by the system architecture, and verify that only one source drives a differential pair at a time.
Factory Automation Bus Interface
The four-channel SN75172N fits factory automation equipment that distributes multiple differential command or data signals between a controller and remote modules. Its 4 megabaud capability provides ample link-rate margin for common industrial message traffic, while 3-state outputs support shared-bus implementations. Designers should account for reflected signals on long cables, maintain consistent reference ground within the installation, and add external protection when the bus leaves an enclosure. The 16-pin PDIP package also simplifies inspection and repair in legacy industrial control systems.
Test and Measurement Front End
Instrumentation systems can use the SN75172N to send control and status information across balanced links between instrument modules, computers, or service equipment. Differential signaling is useful when cables pass near motors, switching supplies, or other industrial noise sources, and the three-state outputs allow bus sharing when required. For accurate measurements, keep the data path separate from sensitive analog inputs and place termination at the physical endpoints. The transmitter must also be paired with a receiver whose input thresholds and common-mode range match the intended RS-422 or RS-485 network.
Data Acquisition Equipment
The SN75172N can supply four balanced command or digital-data channels in a multi-channel data-acquisition system. Its four independent drivers reduce the number of separate transmitter packages required when the acquisition chassis communicates with external sensors, fixtures, or controllers. Up to 4 megabaud operation supports practical telemetry rates, but command-response protocols should include acknowledgments or timeouts to recover from bus contention. External termination, grounding, and protection requirements depend on cable length and topology and should be validated in the assembled system.
Communications Peripherals
The SN75172N is applicable to communications peripherals that transmit only, such as outbound sensor hubs, remote I/O modules, and controller interfaces. Four 3-state differential channels provide flexible enable control, allowing the system to support point-to-point links or a party-line arrangement. The 4.75 V to 5.25 V operating range aligns with conventional 5 V logic systems, while the 16-pin PDIP format supports through-hole construction. Designers should use separate receive channels and avoid confusing this driver-only IC with a full RS-485 transceiver.
工程参考数据: SN75172N ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Product Type | Quadruple differential line driver |
| Driver Channels | 4 |
| Receiver Channels | 0 |
| Output State Control | 3-state |
| Supply Voltage | 4.75 V to 5.25 V |
| Maximum Data Rate | 4 megabaud |
| Interface Standards | EIA/TIA-422-B, RS-485, and ITU-T V.11 |
| Package | 16-pin PDIP |
| Brand | Texas Instruments |
关键差异点
- Four independently usable 3-state transmitter channels (对比 SN75175N)
- Dedicated multipoint transmitter architecture (对比 SN75176BPE4)
- Four megabaud balanced multipoint operation (对比 SN75175N)
设计说明
Route every differential output as a tightly coupled pair with continuous reference-plane support. Keep the two conductors of a channel together, match their geometry as closely as practical, and avoid routing one conductor around clocks, relays, or switching-power nodes. Place termination components at the physical bus endpoints rather than beside every driver, because excessive termination lowers the loaded bus impedance and can increase driver stress.
Decouple the 4.75 V to 5.25 V supply close to the SN75172N power and ground pins using the capacitance and placement specified in the TI application guidance. Keep the ground connection short and place it in the same return path as the outputs. Verify that the supply remains within tolerance during bus enable transitions because an undersized rail can cause differential output asymmetry, false data reception, or unexpected driver operation.
Do not enable multiple SN75172N channels onto the same bus pair at the same time. The 3-state outputs are intended to support multipoint communication, not simultaneous contention. Likewise, do not substitute a receiver-only IC such as the SN75175N for this transmitter-only device. Confirm enable polarity, output impedance, propagation timing, and common-mode limits against the TI datasheet before modifying a production board.
Treat external RS-422 and RS-485 connections as noisy cable ports even when the IC itself is a logic device. Use controlled-rise-time protection networks or external transceivers where surge and ESD requirements exceed the SN75172N's internal capabilities. Maintain a coherent ground reference along the installation and avoid long unprotected stubs, because these practices reduce common-mode excursions and improve reliability in electrically noisy installations.
合规信息
The retrieved manufacturer and distributor material does not explicitly state the compliance status for SN75172N.