STM32F031F4P7 - 48MHz Cortex-M0 16KB Flash MCU | ST
MPN: STM32F031F4P7 ✓ NakahandaSTM32F031F4P7 Ulas
A microcontroller is a programmable system-on-chip that integrates a CPU core, program memory, data memory, peripherals, and I/O into one component. The STM32F031F4P7 belongs to the STM32F0 family, a 32-bit Arm Cortex-M0 product line positioned for general-purpose embedded control. Within the product hierarchy, it combines a microcontroller with embedded Flash, SRAM, timers, an analog-to-digital converter, and communication peripherals.
Key characteristics include a maximum 48 MHz operating frequency, 16 KB (16K x 8) Flash, and 4 KB of SRAM with hardware parity. The family documentation identifies up to nine timers, an ADC, and communication capabilities. A 2.0 V to 3.6 V operating range allows operation from regulated 2.5 V or 3.3 V rails. The extended -40 °C to +105 °C temperature range supports industrial environments where consumer-temperature parts would be unsuitable.
The STM32F031F4P7 uses the Arm Cortex-M0 instruction set with a 32-bit architecture. Hardware parity in the SRAM helps detect memory faults, while the 48 MHz clock rate supports responsive control loops and time-sensitive peripheral operation. Because the device is available in a 20-pin TSSOP package, it offers a practical balance between I/O access, board area, assembly cost, and performance for compact embedded systems.
Typical uses include low-cost sensor controllers, compact industrial monitoring modules, small motor-control subsystems, and communication-enabled edge devices. Its ADC supports analog signal acquisition, its timers support periodic measurement and output functions, and its serial interfaces allow connection to sensors, transceivers, and human-interface modules.
Designers should allocate the 20-pin TSSOP footprint according to the manufacturer pinout and keep decoupling capacitors close to the supply pins. Confirm peripheral availability, alternate-function routing, and firmware support for the specific application before PCB release. The device operates from a 3.6 V maximum supply, so regulator tolerances and transients must remain inside that limit.
This page combines the manufacturer product specification with package-level pinout guidance, drop-in family alternatives, application-oriented design notes, and a practical comparison table for engineers evaluating a TSSOP-20 Cortex-M0 replacement.
Mga alternatibo na pwedeng ilagay na STM32F031F4P7 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok STM32F031F4P7 (parehas na form factor at footprint) — pagkakaiba sa Flash Memory, Package, ADC, Number of Timers, Processor Core.
STM32F031F4P6
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →STM32F031F4P6TR
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
STM32F031F6P6
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →STM32F031F6P6TR
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
STM32F031F4P7 Mga Pinakamataas na Rating at Electrical Characteristics
| Core Processor | ARM Cortex-M0 |
| Architecture | 32-bit RISC |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 16 KB (16K x 8) |
| SRAM | 4 KB with hardware parity |
| Supply Voltage na Operasyon | 2.0 V to 3.6 V |
| Temperature na Operasyon | -40 °C to +105 °C |
| Number of Timers | Up to 9 |
| ADC | 12-bit ADC |
| Packhaging | 20-pin TSSOP |
| Uri ng Pagpapasok | Surface mount |
| Product Line | STM32F0 |
| Supply Configuration | 2.5 V or 3.3 V |
| Processor Core | 32-bit ARM Cortex-M0 |
| Program Memory Type | Flash |
| Peripheral Category | Microcontroller MCU |
Gabay sa Pin Configuration ng STM32F031F4P7 20-pin tssop
Pin configuration para sa STM32F031F4P7 (20-pin tssop package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa STM32F031F4P7.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
STM32F031F4P7 ay nararapat para sa 6 aplikasyons: Compact Industrial Sensor Controller, Low-Cost Motor Control Submodule, Battery-Powered Edge Sensor Node, RS-485 Remote Monitoring Module, Compact IoT Gateway Interface, Human Interface and Control Panel.
Compact Industrial Sensor Controller
The STM32F031F4P7 suits compact sensing modules that must acquire analog measurements, process them locally, and communicate the results over a serial interface. Its 12-bit ADC supports sensor conditioning, while the 48 MHz Cortex-M0 core provides enough performance for filtering and control calculations. The 4 KB SRAM can hold working buffers for short measurement sequences, and the 2.0 V to 3.6 V supply range supports 3.3 V industrial rails. A TSSOP-20 footprint also limits PCB area in densely populated instrument housings.
Inirekomenda
Low-Cost Motor Control Submodule
The STM32F031F4P7 can serve as the control processor in a small motor or actuator module because its family provides up to nine timers for pulse generation, capture, and periodic control. The 48 MHz core allows responsive duty-cycle updates and fault monitoring, while the 16 KB Flash is sufficient for compact control firmware. Its -40 °C to +105 °C range supports industrial environments. External power transistors and protection components remain necessary because the MCU pins are control signals rather than direct motor-power outputs.
Inirekomenda
Battery-Powered Edge Sensor Node
The STM32F031F4P7 is appropriate for small battery-powered sensing nodes where a 3.3 V rail is available and processing must remain compact. The 48 MHz core supports periodic acquisition and event handling, while 16 KB of Flash and 4 KB of SRAM are adequate for small embedded applications. The broad 2.0 V to 3.6 V supply range permits regulated operation above deeply discharged battery voltages. Power-budget decisions should account for sleep modes, peripheral clock gating, and the average current required by the attached sensor and radio.
Inirekomenda
RS-485 Remote Monitoring Module
The STM32F031F4P7 can coordinate an isolated or non-isolated RS-485 measurement node by timestamping readings, applying local thresholds, and formatting data for transmission. Its serial peripherals support communication tasks, and its timers help manage frame timing or periodic sampling. The MCU operates from 2.0 V to 3.6 V, allowing it to share a regulated 3.3 V rail with suitable interface components. The TSSOP-20 package keeps the controller compact, but bus protection, termination, isolation, and grounding must be implemented separately.
Inirekomenda
Compact IoT Gateway Interface
The STM32F031F4P7 can act as the protocol and I/O controller in a small gateway that bridges sensors, local logic, and an upstream communication link. Its 48 MHz Cortex-M0 core handles packet assembly and device-state management, while the ADC permits local analog supervision and the timers provide deterministic intervals. With 16 KB of Flash and 4 KB of SRAM, the MCU is best suited to lightweight gateways rather than high-throughput protocol aggregation. A larger STM32F031F6-family option offers additional Flash when firmware and update buffers require it.
Inirekomenda
Human Interface and Control Panel
The STM32F031F4P7 can manage a small control panel containing buttons, indicator outputs, and one or more simple displays. GPIO multiplexing allows several interface signals to share the limited 20-pin package, while timers support debouncing, periodic updates, or indicator flashing. The 48 MHz core has ample headroom for menu logic and communication with a host controller. Because pin assignment is constrained, plan the panel interface early and confirm alternate-function availability in the manufacturer pinout before placing display and switch connectors.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for STM32F031F4P7 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | STM32F031F4P6 | STM32F031F4P6TR | STM32F031F6P6 | STM32F031F6P6TR |
|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | TSSOP-20 | TSSOP-20 - same footprint | TSSOP-20 - same footprint | TSSOP-20 - same footprint | TSSOP-20 - same footprint |
| Core | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 |
| Maximum Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 16 KB | 16 KB | 16 KB | 32 KB | 32 KB |
| SRAM | 4 KB with hardware parity | 4 KB with hardware parity | 4 KB with hardware parity | 4 KB with hardware parity | 4 KB with hardware parity |
| Operating Supply Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| Operating Temperature | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C |
| Delivery Packaging Code | P7 order code | P6 order code | P6TR order code | P6 order code | P6TR order code |
Pangunahing mga Pagkakaiba
- Compact Cortex-M0 performance with a 20-pin TSSOP footprint (kumpara saSTM32F031F6P6TR)
- Lower program-memory demand for compact control firmware (kumpara saSTM32F031F6P6)
- Same core and memory configuration as the closest order-code alternative (kumpara saSTM32F031F4P6)
Talaan ng Disenyo
Design the supply for a maximum of 3.6 V, including regulator tolerance, startup overshoot, and transient margin. Place the manufacturer-recommended bypass capacitors directly beside the supply and ground pins, with the shortest possible return path. Because several high-speed peripherals can switch simultaneously, route the quiet analog reference and sensitive sensor connections away from digital return currents. A single stable 3.3 V rail is generally easier to implement cleanly than a split 2.5 V and 3.3 V arrangement.
Confirm every signal against the STM32F031F4P7 pin-description table before routing the TSSOP-20 footprint. Alternate functions, oscillator pins, reset behavior, boot configuration, and ground assignments must be considered together; swapping two apparent GPIO positions can disable a timer, communication peripheral, or clock source. Keep the 20-pin footprint free of unnecessary thermal or copper obstacles that interfere with assembly inspection, and follow the manufacturer's land pattern for pin-1 orientation.
Treat analog and digital return paths deliberately. The 12-bit ADC and external sensors can be affected by switching current from timers and communication peripherals. Locate the MCU close to the analog front end when possible, use a quiet analog reference, and separate sensor traces from clock and high-current output routes. If the board mixes sensing and control, review ground-plane partitioning and the placement of decoupling to avoid forcing analog signals across the return current of the digital subsystem.
Do not assume that every STM32F031F4 or STM32F031F6 order code is interchangeable in production. The P6, P6TR, and P7 suffixes encode ordering, grade, or delivery information that must match the assembly process and environmental requirements. Firmware also needs to be validated for the exact MCU, including clock setup, peripheral availability, memory layout, and interrupt configuration. Use the manufacturer ordering guide to confirm each suffix before creating a purchasing line.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer product page and distributor snippets do not state the individual compliance declarations for this order code. Confirm RoHS, REACH, halogen-free, and automotive qualification status with STMicroelectronics before incorporating the claim into a regulated design.