STM32F098RCT6 - 48MHz Cortex-M0 256KB MCU | STMicroelectronics
MPN: STM32F098RCT6 ✓ NakahandaSTM32F098RCT6 Ulas
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. In the hierarchy of embedded semiconductors, the STM32F098RCT6 is an MCU based on the Arm Cortex-M0 processor, an entry-level 32-bit architecture within the wider Arm Cortex family. The STM32F0 series extends into the broader category of embedded processors and microcontrollers used for industrial controls, consumer equipment, communications, and compact automation.
The principal device characteristics include an ARM Cortex-M0 processor operating at 48 MHz, 256 KB of Flash organized as 256K by 8 bits, and operation from low-voltage rails including 1.8 V, 2.5 V, and 3.3 V. Its 64-LQFP package provides 64 external connection points in a 10 mm by 10 mm surface-mount footprint. These characteristics make the device suitable for cost-sensitive embedded products that require more memory and peripheral connectivity than an 8-bit controller.
The STM32F098 integrates a high-performance 32-bit core with fast Flash access and a peripheral set intended for general embedded control. Its operating frequency supports responsive control loops, serial communication, data acquisition, and supervisory tasks. The 256 KB Flash capacity accommodates application firmware, configuration data, and boot logic while allowing developers to implement moderate protocol stacks and human-machine-interface functions without relying on external program memory.
Typical applications include industrial sensing and control equipment, motor and actuator controllers, communication modules, instrumentation, and compact consumer products. In each case, the MCU can combine real-time control with serial communications and multiple digital inputs or outputs. The STM32F098RCT6 is particularly appropriate when a 48 MHz Cortex-M0 core, 256 KB Flash, and 64-pin LQFP package are required in a space-constrained embedded design.
PCB planning should account for the exposed package dimensions, pin pitch, oscillator routing, decoupling, and any communication interfaces used by the design. Place input and output decoupling capacitors close to the appropriate supply pins, keep sensitive clock and signal routes short, and follow the pin-description table in the manufacturer datasheet when assigning tracks. Firmware migration should also confirm startup configuration, peripheral assignment, and low-power behavior.
This page combines the core STM32F098RCT6 specifications, qualified same-footprint alternatives, application guidance, and engineering design notes. It is intended to support MCU selection, PCB footprint planning, procurement, and embedded-system architecture without replacing the complete manufacturer datasheet or reference manual.
Mga alternatibo na pwedeng ilagay na STM32F098RCT6 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok STM32F098RCT6 (parehas na form factor at footprint) — pagkakaiba sa Package, Flash Memory, ADC, Core, DAC.
STM32F090RCT6
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
STM32F091RCT6
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →STM32F099RCT6
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
STM32F358RCT6
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →GD32F103RCT6
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
STM32F098RCT6 Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | 32-bit microcontroller |
| Processor Core | Arm Cortex-M0 |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 256 KB |
| Flash Organization | 256K x 8 bits |
| Operating Voltage Options | 1.8 V, 2.5 V, 3.3 V |
| Packhaging | 64-LQFP (10 mm x 10 mm) |
| Bilang ng Pin | 64 pins |
| Series | STM32F0 |
| Architecture | ARM Cortex-M0 |
| Program Memory Type | Flash |
| Uri ng Pagpapasok | Surface mount |
| Delivery Format | Tray |
| Tindminan RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Gabay sa Pin Configuration ng STM32F098RCT6 64-lqfp (10 mm x 10 mm)
Pin configuration para sa STM32F098RCT6 (64-lqfp (10 mm x 10 mm) package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa STM32F098RCT6.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
STM32F098RCT6 ay nararapat para sa 6 aplikasyons: Industrial Sensor and Control, Motor and Actuator Control, Communication Gateway, Data Acquisition and Instrumentation, LED Lighting Controller, Battery-Powered Embedded Product.
Industrial Sensor and Control
The STM32F098RCT6 fits compact industrial sensing and control nodes that need real-time digital control without the cost of a higher-end processor. Its 48 MHz Arm Cortex-M0 core supports responsive sampling, state-machine execution, and communications handling, while 256 KB Flash provides room for firmware, calibration parameters, and protocol code. The 64-LQFP package exposes substantially more I/O than a small microcontroller package, allowing sensors, relays, status indicators, and serial interfaces to coexist. Designers should allocate pins from the manufacturer pin table, decouple the 1.8 V, 2.5 V, or 3.3 V supply close to the device, and verify the operating-temperature and isolation requirements of the target installation.
Inirekomenda
Motor and Actuator Control
The STM32F098RCT6 can serve as the supervisory controller in a motor, valve, or actuator module because its 48 MHz Cortex-M0 core is fast enough for timing, debouncing, fault detection, and closed-loop control functions. The 256 KB Flash capacity can store motion tables, state machines, diagnostic logs, and field-update logic, while the 64-pin LQFP package provides connections for position feedback, drive commands, and protection signals. In such designs, keep switching devices and high-current return paths away from sensitive control traces, use the timer and interrupt resources according to the reference manual, and validate that the selected external drivers remain compatible with the MCU's low-voltage supply levels and specified operating range.
Inirekomenda
Communication Gateway
The STM32F098RCT6 is well suited to a small protocol gateway or communications terminator requiring more connectivity and firmware space than an 8-bit MCU. Its 32-bit Cortex-M0 core executes at 48 MHz, supporting protocol framing, buffer management, and host-message handling, while 256 KB Flash accommodates networking stacks, configuration data, and update logic. The 64-LQFP package offers a practical balance of interface availability and board area. Keep UART, SPI, or other communication routing away from noisy switching stages, follow the recommended supply and decoupling arrangement, and confirm that every assigned peripheral is available on the selected pin rather than assuming compatibility from the package count alone.
Inirekomenda
Data Acquisition and Instrumentation
The STM32F098RCT6 can act as the acquisition controller in compact instrumentation where an operator needs digital measurements, local processing, and a serial reporting path. The 48 MHz 32-bit Cortex-M0 architecture provides enough execution speed for sampling coordination, filtering, calibration, and status reporting, while 256 KB Flash holds measurement routines and configuration data. The 64-LQFP package is useful when several sensors, display-control signals, and communications lines are required. Maintain short analog input paths, isolate sensitive measurement circuitry from switching nodes, use appropriate external protection for external connectors, and consult the manufacturer electrical characteristics for each supported 1.8 V, 2.5 V, or 3.3 V operating configuration.
Inirekomenda
LED Lighting Controller
The STM32F098RCT6 fits LED lighting modules that require deterministic dimming, status patterns, fault handling, and communication with a host controller. Its 48 MHz Cortex-M0 core can execute timing updates and control algorithms, and the 256 KB Flash capacity leaves room for animation tables, calibration data, and multiple lighting modes. With 64 pins in a 10 mm by 10 mm LQFP package, the device can connect a driver interface, push buttons, indicators, and a communications port while conserving board area. Use timer outputs where possible for repeatable PWM behavior, route LED-driver switching returns carefully, and verify that the external power stage and the MCU use compatible voltage levels.
Inirekomenda
Battery-Powered Embedded Product
The STM32F098RCT6 can support compact battery-powered products in which a 32-bit processor is valuable for efficient control and moderate program-memory capacity. The 48 MHz Cortex-M0 core handles sensor polling, user interaction, and low-power state transitions, while 256 KB Flash reduces the need for a separate program-memory device. The device is specified for low-voltage operation at 1.8 V, 2.5 V, and 3.3 V, allowing the supply to be matched to an energy-storage design. Designers should select the operating rail that supports all peripherals, verify sleep or stop-mode behavior in the reference manual, place decoupling capacitors close to supply pins, and account for regulator efficiency when calculating battery life.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for STM32F098RCT6 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | STM32F090RCT6 | STM32F091RCT6 | STM32F099RCT6 | STM32F358RCT6 | GD32F103RCT6 |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | GigaDevice |
| Package | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) |
| Processor Core | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M4 | Arm Cortex-M3 |
| Flash Memory | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB |
| Series | STM32F0 | STM32F0 | STM32F0 | STM32F0 | STM32F3 | GD32F1 |
Pangunahing mga Pagkakaiba
- Low-complexity 32-bit Cortex-M0 control with substantial Flash memory (kumpara saGD32F103RCT6)
- 64-LQFP footprint within the STM32F0 low-voltage platform (kumpara saSTM32F358RCT6)
- 256 KB Flash in a 10 mm by 10 mm package (kumpara saSTM32F090RCT6)
Talaan ng Disenyo
Use the 64-LQFP land pattern from the manufacturer package drawing and assign every connection from the STM32F098RCT6 pin-description table. Place the required supply-decoupling capacitors immediately adjacent to their corresponding power pins, keep the ground return path short, and route oscillator traces away from relays, motor drivers, and switching-regulator nodes. Because many STM32F0 pins are multiplexed, confirm the alternate function and electrical limits before assigning a peripheral connection.
Design the 1.8 V, 2.5 V, or 3.3 V rail around the voltage range required by the MCU and every attached peripheral. Confirm startup, brownout, and operating limits from the manufacturer datasheet before selecting regulator tolerance and bulk capacitance. Keep the digital supply path separated from noisy analog or power-conversion stages where practical, and use local high-frequency bypass plus controlled return-current paths to reduce supply disturbance at the device.
Do not treat a shared 64-LQFP footprint as proof of automatic firmware compatibility. When changing between STM32F098RCT6 and an alternative, compare boot configuration, interrupt vectors, clock-tree settings, timer assignments, pin multiplexing, peripheral availability, and low-power behavior. For the GD32F103RCT6, also validate register differences and startup code because its Cortex-M3 architecture and 108 MHz maximum clock differ materially from the target Cortex-M0 device at 48 MHz.
Preserve signal integrity by keeping the 48 MHz clock circuit compact, providing a continuous ground reference beneath it, and avoiding test pads or routing discontinuities on sensitive nets. Separate analog inputs from digital and switching paths, use short return routes for external sensors, and apply the manufacturer's recommendations for exposed pad or thermal management where applicable. Validate the final layout with signal-integrity, EMC, and functional tests because the available schematic information does not establish a universal single-layer or two-layer layout.
Impormasyon ng Pagsunod sa Kautusan
Compliance status for the exact STM32F098RCT6 ordering code is not stated in the available product information. Obtain the current manufacturer material-declaration and environmental-compliance records before making a finished-product compliance claim.