STM32F098RCT6 - 48MHz Cortex-M0 256KB MCU | STMicroelectronics
MPN: STM32F098RCT6 ✓ 啟用中STM32F098RCT6 概覽
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. In the hierarchy of embedded semiconductors, the STM32F098RCT6 is an MCU based on the Arm Cortex-M0 processor, an entry-level 32-bit architecture within the wider Arm Cortex family. The STM32F0 series extends into the broader category of embedded processors and microcontrollers used for industrial controls, consumer equipment, communications, and compact automation.
The principal device characteristics include an ARM Cortex-M0 processor operating at 48 MHz, 256 KB of Flash organized as 256K by 8 bits, and operation from low-voltage rails including 1.8 V, 2.5 V, and 3.3 V. Its 64-LQFP package provides 64 external connection points in a 10 mm by 10 mm surface-mount footprint. These characteristics make the device suitable for cost-sensitive embedded products that require more memory and peripheral connectivity than an 8-bit controller.
The STM32F098 integrates a high-performance 32-bit core with fast Flash access and a peripheral set intended for general embedded control. Its operating frequency supports responsive control loops, serial communication, data acquisition, and supervisory tasks. The 256 KB Flash capacity accommodates application firmware, configuration data, and boot logic while allowing developers to implement moderate protocol stacks and human-machine-interface functions without relying on external program memory.
Typical applications include industrial sensing and control equipment, motor and actuator controllers, communication modules, instrumentation, and compact consumer products. In each case, the MCU can combine real-time control with serial communications and multiple digital inputs or outputs. The STM32F098RCT6 is particularly appropriate when a 48 MHz Cortex-M0 core, 256 KB Flash, and 64-pin LQFP package are required in a space-constrained embedded design.
PCB planning should account for the exposed package dimensions, pin pitch, oscillator routing, decoupling, and any communication interfaces used by the design. Place input and output decoupling capacitors close to the appropriate supply pins, keep sensitive clock and signal routes short, and follow the pin-description table in the manufacturer datasheet when assigning tracks. Firmware migration should also confirm startup configuration, peripheral assignment, and low-power behavior.
This page combines the core STM32F098RCT6 specifications, qualified same-footprint alternatives, application guidance, and engineering design notes. It is intended to support MCU selection, PCB footprint planning, procurement, and embedded-system architecture without replacing the complete manufacturer datasheet or reference manual.
直接替換替代品,適用於 STM32F098RCT6 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: STM32F098RCT6 (相同外形與佔位) — 差異在於 Package, Flash Memory, ADC, Core, DAC.
STM32F090RCT6
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
STM32F091RCT6
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →STM32F099RCT6
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
STM32F358RCT6
✅ 直接替換聯絡詢價
查看資料表 →GD32F103RCT6
✅ 直接替換📋 參考替代品(不在目錄中)
STM32F098RCT6 最大額定值與電氣特性
| Product Type | 32-bit microcontroller |
| Processor Core | Arm Cortex-M0 |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 256 KB |
| Flash Organization | 256K x 8 bits |
| Operating Voltage Options | 1.8 V, 2.5 V, 3.3 V |
| 封裝 | 64-LQFP (10 mm x 10 mm) |
| 腳位數 | 64 pins |
| Series | STM32F0 |
| Architecture | ARM Cortex-M0 |
| Program Memory Type | Flash |
| 安裝類型 | Surface mount |
| Delivery Format | Tray |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
STM32F098RCT6 64-lqfp (10 mm x 10 mm) 腳位配置指南
STM32F098RCT6(64-lqfp (10 mm x 10 mm) 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: STM32F098RCT6.
請參閱 資料表 以查看完整腳位配置。
典型應用
STM32F098RCT6 適用於 6 應用s: Industrial Sensor and Control, Motor and Actuator Control, Communication Gateway, Data Acquisition and Instrumentation, LED Lighting Controller, Battery-Powered Embedded Product.
Industrial Sensor and Control
The STM32F098RCT6 fits compact industrial sensing and control nodes that need real-time digital control without the cost of a higher-end processor. Its 48 MHz Arm Cortex-M0 core supports responsive sampling, state-machine execution, and communications handling, while 256 KB Flash provides room for firmware, calibration parameters, and protocol code. The 64-LQFP package exposes substantially more I/O than a small microcontroller package, allowing sensors, relays, status indicators, and serial interfaces to coexist. Designers should allocate pins from the manufacturer pin table, decouple the 1.8 V, 2.5 V, or 3.3 V supply close to the device, and verify the operating-temperature and isolation requirements of the target installation.
推薦
Motor and Actuator Control
The STM32F098RCT6 can serve as the supervisory controller in a motor, valve, or actuator module because its 48 MHz Cortex-M0 core is fast enough for timing, debouncing, fault detection, and closed-loop control functions. The 256 KB Flash capacity can store motion tables, state machines, diagnostic logs, and field-update logic, while the 64-pin LQFP package provides connections for position feedback, drive commands, and protection signals. In such designs, keep switching devices and high-current return paths away from sensitive control traces, use the timer and interrupt resources according to the reference manual, and validate that the selected external drivers remain compatible with the MCU's low-voltage supply levels and specified operating range.
推薦
Communication Gateway
The STM32F098RCT6 is well suited to a small protocol gateway or communications terminator requiring more connectivity and firmware space than an 8-bit MCU. Its 32-bit Cortex-M0 core executes at 48 MHz, supporting protocol framing, buffer management, and host-message handling, while 256 KB Flash accommodates networking stacks, configuration data, and update logic. The 64-LQFP package offers a practical balance of interface availability and board area. Keep UART, SPI, or other communication routing away from noisy switching stages, follow the recommended supply and decoupling arrangement, and confirm that every assigned peripheral is available on the selected pin rather than assuming compatibility from the package count alone.
推薦
Data Acquisition and Instrumentation
The STM32F098RCT6 can act as the acquisition controller in compact instrumentation where an operator needs digital measurements, local processing, and a serial reporting path. The 48 MHz 32-bit Cortex-M0 architecture provides enough execution speed for sampling coordination, filtering, calibration, and status reporting, while 256 KB Flash holds measurement routines and configuration data. The 64-LQFP package is useful when several sensors, display-control signals, and communications lines are required. Maintain short analog input paths, isolate sensitive measurement circuitry from switching nodes, use appropriate external protection for external connectors, and consult the manufacturer electrical characteristics for each supported 1.8 V, 2.5 V, or 3.3 V operating configuration.
推薦
LED Lighting Controller
The STM32F098RCT6 fits LED lighting modules that require deterministic dimming, status patterns, fault handling, and communication with a host controller. Its 48 MHz Cortex-M0 core can execute timing updates and control algorithms, and the 256 KB Flash capacity leaves room for animation tables, calibration data, and multiple lighting modes. With 64 pins in a 10 mm by 10 mm LQFP package, the device can connect a driver interface, push buttons, indicators, and a communications port while conserving board area. Use timer outputs where possible for repeatable PWM behavior, route LED-driver switching returns carefully, and verify that the external power stage and the MCU use compatible voltage levels.
推薦
Battery-Powered Embedded Product
The STM32F098RCT6 can support compact battery-powered products in which a 32-bit processor is valuable for efficient control and moderate program-memory capacity. The 48 MHz Cortex-M0 core handles sensor polling, user interaction, and low-power state transitions, while 256 KB Flash reduces the need for a separate program-memory device. The device is specified for low-voltage operation at 1.8 V, 2.5 V, and 3.3 V, allowing the supply to be matched to an energy-storage design. Designers should select the operating rail that supports all peripherals, verify sleep or stop-mode behavior in the reference manual, place decoupling capacitors close to supply pins, and account for regulator efficiency when calculating battery life.
推薦
推薦產品摘要
工程參考資料,適用於 STM32F098RCT6 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | STM32F090RCT6 | STM32F091RCT6 | STM32F099RCT6 | STM32F358RCT6 | GD32F103RCT6 |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | GigaDevice |
| Package | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) |
| Processor Core | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M4 | Arm Cortex-M3 |
| Flash Memory | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB |
| Series | STM32F0 | STM32F0 | STM32F0 | STM32F0 | STM32F3 | GD32F1 |
主要差異化特點
- Low-complexity 32-bit Cortex-M0 control with substantial Flash memory (對比GD32F103RCT6)
- 64-LQFP footprint within the STM32F0 low-voltage platform (對比STM32F358RCT6)
- 256 KB Flash in a 10 mm by 10 mm package (對比STM32F090RCT6)
設計說明
Use the 64-LQFP land pattern from the manufacturer package drawing and assign every connection from the STM32F098RCT6 pin-description table. Place the required supply-decoupling capacitors immediately adjacent to their corresponding power pins, keep the ground return path short, and route oscillator traces away from relays, motor drivers, and switching-regulator nodes. Because many STM32F0 pins are multiplexed, confirm the alternate function and electrical limits before assigning a peripheral connection.
Design the 1.8 V, 2.5 V, or 3.3 V rail around the voltage range required by the MCU and every attached peripheral. Confirm startup, brownout, and operating limits from the manufacturer datasheet before selecting regulator tolerance and bulk capacitance. Keep the digital supply path separated from noisy analog or power-conversion stages where practical, and use local high-frequency bypass plus controlled return-current paths to reduce supply disturbance at the device.
Do not treat a shared 64-LQFP footprint as proof of automatic firmware compatibility. When changing between STM32F098RCT6 and an alternative, compare boot configuration, interrupt vectors, clock-tree settings, timer assignments, pin multiplexing, peripheral availability, and low-power behavior. For the GD32F103RCT6, also validate register differences and startup code because its Cortex-M3 architecture and 108 MHz maximum clock differ materially from the target Cortex-M0 device at 48 MHz.
Preserve signal integrity by keeping the 48 MHz clock circuit compact, providing a continuous ground reference beneath it, and avoiding test pads or routing discontinuities on sensitive nets. Separate analog inputs from digital and switching paths, use short return routes for external sensors, and apply the manufacturer's recommendations for exposed pad or thermal management where applicable. Validate the final layout with signal-integrity, EMC, and functional tests because the available schematic information does not establish a universal single-layer or two-layer layout.
合規資訊
Compliance status for the exact STM32F098RCT6 ordering code is not stated in the available product information. Obtain the current manufacturer material-declaration and environmental-compliance records before making a finished-product compliance claim.