STM32F745VGH6 - 216MHz Cortex-M7 MCU, 1MB Flash | STMicroelectronics
MPN: STM32F745VGH6 ✗ Tapus ng BuhaySTM32F745VGH6 Ulas
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one component. In the embedded-device hierarchy, this MCU belongs to the STM32 family, uses the Arm Cortex-M7 processor architecture, and sits within the broader category of embedded semiconductors. Its 32-bit RISC core executes control, communications, signal-processing, and real-time workloads while consuming less power than many application processors.
The verified device data identifies the STM32F745VGH6 as part of the STM32F7 high-performance series. The STM32F745xx and STM32F746xx families are based on the Arm Cortex-M7 core and operate at up to 216 MHz. The H6 ordering suffix denotes the exact ordering variant, while the 100-TFBGA package provides 100 solderable BGA contacts in an 8 x 8 mm footprint.
Key engineering considerations include adequate PCB routing for the dense BGA land pattern, careful power and decoupling layout, boot configuration, clock stability, and firmware support for every peripheral used. Because the verified search results do not provide a complete pin-by-pin mapping, voltage limits, memory-map details, GPIO count, or peripheral inventory, those values must be confirmed in the manufacturer datasheet before schematic capture or PCB release.
Typical applications include industrial automation controllers, connected industrial equipment, high-speed human-interface systems, audio and digital signal-processing equipment, communications infrastructure, and embedded gateways. The 216 MHz Cortex-M7 performance is particularly useful for workloads combining real-time control with substantial data movement, although actual throughput depends on memory access, cache behavior, peripherals, and firmware optimization.
Design work should begin with the official STM32F745VG documentation and the exact package drawing. Verify every BGA ball, exposed pad connection, power domain, decoupling value, and pin-multiplex alternative before layout. Do not substitute an LQFP footprint or an MCU with fewer I/O resources without a controlled redesign and firmware review.
This page combines verified manufacturer and distributor information, commercial availability references, and engineering-oriented selection guidance. It is intended to support early sourcing decisions while clearly separating confirmed data from parameters that still require datasheet verification.
Mga alternatibo na pwedeng ilagay na STM32F745VGH6 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok STM32F745VGH6 (parehas na form factor at footprint) — pagkakaiba sa Product Type, Package, Flash Memory.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboSTM32F745VGH6 Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | 32-bit microcontroller IC |
| Processor Core | Arm Cortex-M7 |
| Instruction Architecture | 32-bit RISC |
| Maximum CPU Frequency | 216 MHz |
| Flash Memory | 1 MB (1M x 8) |
| Packhaging | 100-TFBGA (8 x 8 mm) |
| Bilang ng Pin | 100 BGA contacts |
| Uri ng Pagpapasok | Surface mount |
| Core Family | STM32F7 series |
| Device Family | STM32F745xx |
| Related High-Performance Family | STM32F746xx |
Gabay sa Pin Configuration ng STM32F745VGH6 100-tfbga (8 x 8 mm)
Pin configuration para sa STM32F745VGH6 (100-tfbga (8 x 8 mm) package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa STM32F745VGH6.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
STM32F745VGH6 ay nararapat para sa 6 aplikasyons: Industrial Automation Controller, High-Speed Communications Gateway, Digital Signal Processing System, Connected Audio and Interface Equipment, Human-Machine Interface Controller, Programmable Test and Measurement Equipment.
Industrial Automation Controller
The STM32F745VGH6 fits an industrial controller that must combine real-time control with communications, diagnostics, and data preparation. Its Arm Cortex-M7 core operates up to 216 MHz, providing substantial control-loop headroom, while 1 MB of flash can hold application firmware, communication stacks, and diagnostics. Place the 100-TFBGA device beside local sensors and power-control interfaces, then isolate analog and high-current paths on the PCB. Confirm exact I/O availability, supply rails, timer mappings, and operating-temperature limits in the manufacturer documentation before freezing the design.
Inirekomenda
High-Speed Communications Gateway
The 216 MHz Cortex-M7 core and 1 MB flash configuration make STM32F745VGH6 suitable for an embedded communications gateway handling protocol processing and control traffic. The device can sit between physical-layer transceivers and a network processor, provided its exact Ethernet, USB, serial, and DMA resources are verified. Keep high-speed clocks, interfaces, and power supplies routed away from sensitive analog sections. Because the supplied evidence does not enumerate the peripheral set, firmware bring-up must begin with the exact reference manual and pin table rather than assumptions based on the STM32 family name.
Inirekomenda
Digital Signal Processing System
STM32F745VGH6 is relevant for embedded DSP when the Cortex-M7's 216 MHz execution capability can support filtering, transforms, or waveform control while retaining local flash-based firmware. Its benefit is integration: control code, signal processing, and peripheral management can run in one microcontroller instead of requiring a separate processor. Validate cache behavior, memory bandwidth, timer synchronization, and peripheral DMA paths in the exact device documentation. The 100-TFBGA footprint also demands fine-pitch assembly capability, so prototype fabrication and inspection should be planned alongside software bring-up.
Inirekomenda
Connected Audio and Interface Equipment
The STM32F745VGH6 can serve as the control processor in connected audio equipment, instrument panels, or multimedia interfaces where a fast 32-bit core and 1 MB flash support application logic and real-time control. Pair it with an audio codec or DAC through verified digital interfaces and keep analog audio routing separate from switching and clock-distribution circuitry. Exact I/O mapping, audio clock support, DMA behavior, and peripheral availability are not established by the supplied search snippets, so the engineer must select audio interfaces only after reviewing the official pin table and electrical characteristics.
Inirekomenda
Human-Machine Interface Controller
STM32F745VGH6 is suitable for a graphical or touch-based human-machine interface when the design benefits from a 216 MHz Cortex-M7 and consolidated firmware storage. It can coordinate display updates, touch or keypad input, communications, and application logic in one package. The 8 x 8 mm 100-TFBGA outline supports compact products but requires careful escape routing and a reliable assembly process. Verify LCD or display-interface availability, external memory requirements, operating-temperature range, and pin multiplexing in the exact STM32F745VGH6 documentation before selecting companion display components.
Inirekomenda
Programmable Test and Measurement Equipment
The 216 MHz Cortex-M7 performance can help the STM32F745VGH6 coordinate acquisition, control, calibration, and communications in programmable instrumentation. Its 1 MB flash provides space for control code and test sequences, while the MCU consolidates functions that might otherwise require several processors. The dense BGA package should be paired with a short, controlled analog layout and solid reference-clock design. Verify ADC performance, DAC availability, comparators, timer channels, external-memory interfaces, and calibrated measurement paths directly from the manufacturer documentation before assigning analog functions.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for STM32F745VGH6 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Pangunahing mga Pagkakaiba
- High verified CPU operating point (kumpara saSTM32G474VEH6)
- Large embedded flash configuration (kumpara saSTM32H750XBH6)
- Compact verified BGA package (kumpara saSTM32F746xx devices)
Talaan ng Disenyo
Treat the 100-TFBGA footprint as a fine-pitch assembly constraint rather than a simple 8 x 8 mm land pattern. Obtain the exact package drawing and land pattern from STMicroelectronics before schematic and PCB release. Verify ball size, ball pitch, solder-mask definition, paste apertures, component orientation, and any exposed thermal or ground connection. Prototype assembly should include suitable inspection because hidden BGA joints are not visually inspectable after reflow.
Power planning must begin with the exact voltage domains, regulator ratings, decoupling values, and sequencing requirements in the STM32F745VGH6 documentation; those values are not present in the supplied verified snippets. Place required bulk and local decoupling at the device-side supply and ground connections, preserve the recommended return paths, and isolate noisy switching converters from sensitive references. Do not select inductors, capacitors, or power switches until the datasheet supply limits and transient requirements are confirmed.
Do not assume that another STM32F7 or STM32H7 device is pin-compatible merely because it uses a similar microcontroller family or BGA size. The supplied cross-reference results identify comparison candidates but do not verify a shared 100-ball map, memory organization, voltage architecture, boot configuration, or peripheral assignment. Any substitution requires a formal ball-by-ball review, PCB comparison, clock and power review, peripheral remapping plan, and firmware regression test.
Reserve clean routing for high-speed clock, high-speed serial, and memory-related signals only after the actual pin assignments and external components are known. Keep sensitive analog inputs away from switching nodes and digital return-current discontinuities, and maintain continuous ground references beneath signal routes where the package and stack-up allow. Because the supplied evidence does not include the full pinout or stack-up guidance, use the official package, board-design, and reference-manual documents before releasing layout constraints.
Impormasyon ng Pagsunod sa Kautusan
The supplied verified web data does not state compliance status for this exact ordering code. Compliance claims must be confirmed from the manufacturer product documentation and current distributor records.
