STM32L451CCU6 - 80MHz Cortex-M4 MCU | STMicroelectronics
MPN: STM32L451CCU6 ✓ NakahandaSTM32L451CCU6 Ulas
An ultra-low-power microcontroller is designed to maintain useful processing performance while minimizing energy consumption during active, sleep, and low-power operating states. In the system hierarchy, the STM32L451CCU6 is a microcontroller MCU based on a 32-bit RISC processor, combining embedded processing, memory, peripherals, and power-management functions on one integrated circuit.
Key features include an Arm Cortex-M4 core operating up to 80 MHz, an integrated FPU, 256 KB of Flash memory, and a 48-UFQFPN package. According to the STM32L451xx manufacturer datasheet, the broader STM32L451xx family is positioned for ultra-low-power applications and can deliver performance up to 100 DMIPS. These characteristics support responsive control loops and efficient firmware execution without requiring a separate processor and supporting ICs.
The device belongs to the STM32L4 product family, where low-power design is combined with a high-performance Cortex-M4 core and extensive mixed-signal peripherals. Its 256 KB Flash capacity provides on-chip program storage for control firmware, configuration data, and application logic. The compact 7 x 7 mm package also reduces board footprint, although designers must plan adequate copper area for thermal dissipation and careful layout around exposed-pad and high-speed signals.
Typical applications include industrial sensor nodes, low-power wireless equipment, building controls, battery-powered instruments, motor-control subsystems, compact data loggers, and consumer accessories. The MCU is especially suitable where low-power behavior, compact size, and real-time 32-bit processing are required in the same device. Analog and timing capabilities can reduce the component count in measurement and control designs.
For implementation, review the complete UFQFPN pin definition, exposed-pad connection, decoupling requirements, clock configuration, and low-power mode constraints in the manufacturer datasheet. Firmware should enable peripheral clocks individually, retain the correct reset and boot configuration, and use the documented low-power transitions to obtain the intended energy savings.
This product page combines the manufacturer specifications, package and memory details, practical application guidance, same-package replacement analysis, and design considerations to support faster component selection and PCB planning. It emphasizes engineering trade-offs that matter when embedding the STM32L451CCU6 in a compact, low-power system.
Mga alternatibo na pwedeng ilagay na STM32L451CCU6 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok STM32L451CCU6 (parehas na form factor at footprint) — pagkakaiba sa Package, Processor Core.
STM32L452CCU6
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →STM32L431CCU6
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
STM32L471CCU6
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
STM32L432CCU6
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
STM32L441CCU6
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
STM32L451CCU6 Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | Ultra-low-power 32-bit microcontroller |
| Manufacturer | STMicroelectronics |
| Processor Core | Arm Cortex-M4 |
| Architecture | 32-bit RISC |
| Maximum Core Frequency | 80 MHz |
| Floating-Point Unit | Integrated FPU |
| Family Performance Rating | Up to 100 DMIPS |
| Flash Memory | 256 KB |
| Flash Organization | 256K x 8 bits |
| Packhaging | 48-UFQFPN, 7 x 7 mm |
| Bilang ng Pin | 48 pins |
| Uri ng Pagpapasok | Surface mount |
Gabay sa Pin Configuration ng STM32L451CCU6 48-ufqfpn, 7 x 7 mm
Pin configuration para sa STM32L451CCU6 (48-ufqfpn, 7 x 7 mm package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa STM32L451CCU6.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
STM32L451CCU6 ay nararapat para sa 6 aplikasyons: Industrial Sensor Nodes, Battery-Powered Instruments, Building Automation, Motor Control Subsystems, Compact Data Loggers, Low-Power Connectivity Equipment.
Industrial Sensor Nodes
STM32L451CCU6 fits industrial sensor nodes that need local signal conditioning, configuration, and control while maintaining a compact board footprint. Its 80 MHz Arm Cortex-M4 core and integrated FPU can execute filtering and control algorithms, while 256 KB of Flash stores firmware, calibration tables, and configuration data. The 48-pin UFQFPN package supports integration beside sensors and interface ICs without expanding the design beyond a 7 x 7 mm device footprint. Low-power operation is particularly valuable when measurements occur at intervals and the main MCU spends substantial time between active processing cycles. Validate the selected sleep mode, wake sources, analog performance, and peripheral availability against the application workload.
Inirekomenda
Battery-Powered Instruments
STM32L451CCU6 is suitable for battery-powered measurement instruments that must balance responsive processing with energy efficiency. The 80 MHz Cortex-M4 core provides enough performance for local calculations, menu logic, and sensor fusion, while 256 KB of Flash provides dedicated program storage for a compact embedded design. Low-power STM32L4 operation can help reduce energy use during idle intervals, provided the designer configures clocks, peripherals, debug behavior, and wake conditions correctly. The 48-pin UFQFPN package also leaves board space for power conversion and storage. For a final battery-life assessment, measure the complete system rather than the MCU alone, including regulator efficiency, pull-up networks, indicator currents, and sensor standby consumption.
Inirekomenda
Building Automation
STM32L451CCU6 can serve as the control MCU in building automation equipment such as room controllers, environmental monitors, and distributed actuator nodes. Its Cortex-M4 processing capability supports event handling, scheduled control, and communication-stack tasks, while 256 KB of Flash is sufficient for a focused control application. The ultra-low-power family positioning supports designs that spend much of their operating cycle waiting for timers, sensor updates, or network events. Its 48-pin UFQFPN package permits compact placement behind controls and in distributed wall or ceiling modules. Before deployment, verify the exact UART, I2C, SPI, timer, and low-power resources required by the building system, along with environmental limits and bus isolation requirements.
Inirekomenda
Motor Control Subsystems
STM32L451CCU6 is suitable for small motor-control and actuator subsystems where local real-time processing, compactness, and low-power behavior are important. The 80 MHz Arm Cortex-M4 core can execute control tasks, while the integrated FPU supports common signal calculations used in motion or current-control loops. Its 256 KB Flash capacity allows firmware, configuration, and lookup data to remain on-chip, and the 48-pin UFQFPN package simplifies compact controller layouts. The MCU does not remove the need for external power-stage components, gate drivers, current sensing, and protection. Validate timer channels, encoder interfaces, ADC characteristics, control-loop latency, and shutdown paths against the STM32L451xx documentation before assigning the device to a safety-relevant motor function.
Inirekomenda
Compact Data Loggers
STM32L451CCU6 works well in compact data loggers that combine periodic sensor acquisition with local processing and nonvolatile data transfer. Its 256 KB Flash can hold operating firmware and a bounded local data buffer, while the 80 MHz Cortex-M4 core can compress, filter, or timestamp collected measurements. The 48-pin UFQFPN package minimizes the controller footprint, leaving room for external storage, interface protection, and power management. Low-power characteristics can benefit designs that record only at scheduled intervals by reducing active time between acquisitions. The engineering trade-off is that external memory, file-system complexity, and continuous communication can dominate total power consumption. Select external interfaces and storage methods based on logging interval, data volume, retention requirements, and the system's maximum idle duration.
Inirekomenda
Low-Power Connectivity Equipment
STM32L451CCU6 can act as the low-power host controller in compact wireless equipment, provided the selected radio interface and protocol stack operate within its available resources. The Cortex-M4 core executes up to 80 MHz, the FPU accelerates common DSP routines, and 256 KB of Flash stores application and protocol firmware. The 48-pin UFQFPN package is useful in wearables, IoT endpoints, and portable accessories where board area is constrained. Low-power execution supports duty-cycled communication designs, but radio current and sleep-mode transitions usually dominate overall energy use. Confirm the MCU's exact communication peripherals, RAM requirement, DMA channels, and package assignments against the manufacturer documentation, and validate the complete firmware stack with the selected wireless module.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for STM32L451CCU6 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | STM32L452CCU6 | STM32L431CCU6 | STM32L471CCU6 | STM32L432CCU6 | STM32L441CCU6 |
|---|---|---|---|---|---|---|
| Package | 48-UFQFPN (7 x 7 mm) | 48-UFQFPN (7 x 7 mm) | 48-UFQFPN (7 x 7 mm) | 48-UFQFPN (7 x 7 mm) | 48-UFQFPN (7 x 7 mm) | 48-UFQFPN (7 x 7 mm) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
Pangunahing mga Pagkakaiba
- Balances an 80 MHz Cortex-M4 core with 256 KB of Flash in a compact package (kumpara saSTM32L431CCU6)
- Supports designs that later need upgraded security capabilities (kumpara saSTM32L452CCU6)
- Provides expanded peripherals for feature-rich connected designs (kumpara saSTM32L471CCU6)
Talaan ng Disenyo
Use the STMicroelectronics UFQFPN48 land pattern and exposed-pad recommendation for the STM32L451CCU6 rather than a generic 48-pin QFN footprint. Confirm pin-one orientation, pad dimensions, solder-mask clearance, and paste stencil geometry against the package drawing. Provide the required local decoupling directly beside the associated supply pins and keep sensitive analog returns away from switching-node and high-current paths.
Plan the power tree around the MCU's internal voltage domains and the STM32L451xx electrical-characteristics tables. Decouple each required rail independently, maintain the documented sequencing relationships, and avoid routing return currents beneath noisy analog or switching areas. If low-power operation is central to the design, include the leakage of pull-ups, level shifters, sensors, and regulators in the system current budget because their consumption can dominate MCU standby current.
Do not assume that every STM32L4 device with a similar package is software-compatible. Before substituting STM32L452CCU6, STM32L431CCU6, STM32L471CCU6, STM32L432CCU6, or STM32L441CCU6, compare the peripheral mix, interrupt assignments, boot behavior, memory map, clock tree, security features, and low-power modes. Rebuild and validate the firmware with the selected device rather than assuming that identical pin placement guarantees identical behavior.
Keep oscillator and decoupling paths compact, preserve continuous ground beneath the MCU where recommended, and route high-current outputs away from analog inputs. The 7 x 7 mm UFQFPN package allows dense placement, but small geometry can increase thermal gradients and coupling between adjacent nets. Review the exposed-pad copper plan with the assembly house and use thermal-via patterns only where compatible with the recommended footprint.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer product page and STM32L451xx datasheet were used for product identity, family, processor, frequency, memory class, and package information. Specific compliance declarations were not stated in the cited material, so each status remains unknown.