SY87725LHY - 4-Bit 2.5G ONU SerDes | Microchip
MPN: SY87725LHY ✓ NakahandaSY87725LHY Ulas
A SerDes transceiver is an interface IC that converts parallel data into a high-speed serial stream and converts a received serial stream back into parallel data. In the broader semiconductor hierarchy, the SY87725LHY belongs to the interface transceiver class, then to high-speed communications ICs, and ultimately to the semiconductor category. Optical network units use this type of interface to connect a processor or network controller to a PON signal path while reducing parallel data-bus pin requirements.
The device's principal functions include four-bit parallel-to-serial and serial-to-parallel conversion, LVDS signaling, downstream-channel rate selection, and upstream-channel rate support. Its listed 3.3 V operating range spans 3.15 V to 3.45 V. The available technical information identifies the SY87725LHY specifically for PON and optical access applications rather than general-purpose board-to-board LVDS links.
The four-bit interface provides a practical balance between host throughput and package complexity. At the highest listed downstream rate of 2.5 Gbit/s, the serial output supports substantially greater line-rate capability than the 1.25 Gbit/s downstream mode. Upstream operation is listed from 156 Mbit/s through 1.25 Gbit/s, allowing a network design to accommodate different service directions according to PON architecture and link requirements.
Typical uses include GPON-class ONU signal paths, XGS-PON-oriented downstream links, PON media-conversion assemblies, optical network terminal equipment, and central-office line-card interfaces where a compact four-bit SerDes connects parallel PHY logic to high-speed serial channels. The single-chip integration reduces the number of separate conversion and interface functions required around the system controller.
Layout is especially important because LVDS and multi-gigabit SerDes interfaces can be sensitive to return-path discontinuities, imperfect reference-clock distribution, and uncontrolled differential impedance. Place decoupling capacitors close to the supply pins, maintain a continuous ground plane, and follow the manufacturer's recommended reference design for differential routing and exposed-pad connection. Confirm all rate modes with the clocking, I/O, and channel requirements of the selected PON system.
This page combines the manufacturer-derived operating details, PON rate coverage, package information, sourcing workflow, and engineering guidance needed to evaluate the SY87725LHY. It also distinguishes the exact ordered MPN from related catalog identifiers and provides explicit selection criteria for designing a new optical access interface or assessing an existing board revision.
Mga alternatibo na pwedeng ilagay na SY87725LHY — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboSY87725LHY Mga Spesipikasyon
| Device Type | Single-chip LVDS transceiver |
| Serializer/Deserializer Width | 4 bit |
| Supply Voltage Range | 3.15 V to 3.45 V |
| Nominal Supply Voltage | 3.3 V |
| Maximum Downstream Data Rate | 2.5 Gbit/s |
| Supported Downstream Data Rates | 2.5 Gbit/s, 1.25 Gbit/s, and 625 Mbit/s |
| Maximum Upstream Data Rate | 1.25 Gbit/s |
| Supported Upstream Data Rates | 1.25 Gbit/s, 625 Mbit/s, and 156 Mbit/s |
| Signal Protocol | LVDS |
| Primary Application | Passive optical network and optical access |
| Packhaging | 64-lead TQFP with exposed pad |
| Package Dimensions | 10 mm x 10 mm |
| Hanay ng Temperature na Operasyon | -40 °C to +85 °C |
| Uri ng Pagpapasok | Surface mount |
Gabay sa Pin Configuration ng SY87725LHY 10 mm x 10 mm
Pin configuration para sa SY87725LHY (10 mm x 10 mm package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa SY87725LHY.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
SY87725LHY ay nararapat para sa 6 aplikasyons: GPON Optical Network Terminal, XGS-PON Downstream Interface, PON Media Converter, Optical Line-Card Interface, High-Speed Parallel-to-Serial Bridge, Optical Access Test Equipment.
GPON Optical Network Terminal
The SY87725LHY fits the SerDes section of a GPON-oriented optical network terminal because it supports downstream rates of 1.25 Gbit/s and 625 Mbit/s as well as upstream operation through 1.25 Gbit/s. The four-bit conversion interface connects parallel network-controller logic to a high-speed differential channel without requiring separate serializer and deserializer packages. Its 3.15 V to 3.45 V supply range is centered on 3.3 V optical-access equipment. Confirm the selected PON mode, reference-clock architecture, and controller pin assignment against the manufacturer datasheet before finalizing the schematic.
XGS-PON Downstream Interface
For an XGS-PON-class downstream path, the SY87725LHY can use its 2.5 Gbit/s downstream mode to move high-rate serialized traffic between parallel logic and the optical-transceiver signal chain. The four-bit internal interface provides a structured division of data between parallel and serial domains, while the 3.3 V supply operation suits compact line-card electronics. The implementation must preserve the manufacturer reference design's differential impedance, clocking, decoupling, and exposed-pad grounding to maintain signal integrity at the highest listed rate.
PON Media Converter
A PON media converter can place the SY87725LHY between a parallel FPGA or network controller and a high-speed differential PHY stage. The converter benefits from the device's 2.5 Gbit/s downstream rate, 1.25 Gbit/s maximum upstream rate, and four-bit parallel interface. Because the same package supports multiple line rates, one board architecture may cover several PON service modes. Validate each supported rate with the intended reference clock and magnetics or optical-interface circuitry rather than treating all rate settings as interchangeable.
Optical Line-Card Interface
The SY87725LHY is applicable to central-office and access-network line cards that convert parallel control or traffic data into LVDS serial channels. Its highest downstream rate of 2.5 Gbit/s supports high-throughput downstream traffic, while the 625 Mbit/s and 156 Mbit/s upstream options accommodate lower-rate return paths. Integration in a 64-lead TQFP exposed-pad package supports compact multilayer PCB designs, provided the thermal pad receives uninterrupted ground-plane connection and the high-speed nets follow controlled impedance routing.
High-Speed Parallel-to-Serial Bridge
The SY87725LHY can serve as the conversion stage in a high-speed parallel-to-serial bridge when a controller exposes four parallel data bits but requires a differential serial link. Its LVDS interface and selectable PON-oriented rates make it relevant to optical-access equipment rather than an arbitrary general-purpose communications link. System designers should verify the serializer's parallel clocking, coding, control pins, and channel polarity in the manufacturer datasheet, then implement controlled-length differential routing and a low-noise reference-clock network.
Optical Access Test Equipment
The SY87725LHY can be incorporated into optical access test equipment that must generate or analyze PON-compatible downstream and upstream traffic. Its defined rates of 2.5 Gbit/s, 1.25 Gbit/s, 625 Mbit/s, and 156 Mbit/s allow the same platform to exercise several link modes. The 3.3 V operating range and compact 10 mm by 10 mm TQFP package facilitate instrumentation, but accurate measurements still depend on a clean reference clock, controlled impedance, solid ground return paths, and calibration of the external optical and electrical test paths.
Impormasyon ng Talumpati sa Engineering for SY87725LHY — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Package | 64-lead TQFP with exposed pad, 10 mm x 10 mm |
| Brand | Microchip Technology |
| Device Type | Single-chip 4-bit SerDes transceiver |
| Supply Voltage Range | 3.15 V to 3.45 V |
| Signal Protocol | LVDS |
| Maximum Downstream Rate | 2.5 Gbit/s |
| Maximum Upstream Rate | 1.25 Gbit/s |
| Operating Temperature Range | -40 °C to +85 °C |
| Primary Application | PON and optical access |
Pangunahing mga Pagkakaiba
- Integrated four-bit SerDes optimized for optical access (kumpara saGeneric LVDS transceiver)
- Multiple downstream operating rates (kumpara saSingle-rate generic transceiver)
- Multiple upstream operating rates (kumpara saFixed-rate upstream interface)
Talaan ng Disenyo
Treat the high-speed differential nets as controlled-impedance routed structures and follow the manufacturer reference layout. Keep return paths continuous beneath the pairs, avoid discontinuities across plane transitions, and match the two conductors of each differential pair as closely as practical. Place the exposed-pad connection directly into the ground plane with minimal thermal-pad impedance, and keep unrelated switching or digital return currents away from the SerDes and reference-clock regions.
Decouple the 3.3 V supply locally at the transceiver's supply pins using the capacitance and placement specified by the manufacturer. Confirm current draw in every supported downstream and upstream rate mode before sizing the regulator and copper area. Maintain short, wide supply and ground connections so switching resistance and loop inductance do not degrade signal integrity during simultaneous high-speed activity.
The 2.5 Gbit/s downstream mode is the most demanding timing condition and should be evaluated with realistic reference-clock quality, package parasitics, PCB stack-up, and downstream loading. Use the manufacturer's recommended clock-generation and termination arrangements, and verify rise time, jitter, eye opening, and differential voltage through simulation or measurement. Do not infer signal margin from a successful link at a lower supported rate.
Impormasyon ng Pagsunod sa Kautusan
RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer's current product documentation or declaration.