SY89202UMI - 1:8 1.5 GHz Clock Buffer | Microchip Technology
MPN: SY89202UMI ✗ Tapus ng BuhaySY89202UMI Ulas
A clock fanout buffer is a timing-device class that replicates one input clock across multiple outputs while controlling skew and jitter. Clock buffers can also support frequency division and multiplexing when the required configuration permits it. Within the broader hierarchy, the SY89202UMI belongs to the clock buffer and driver category, which falls under clock and timing integrated circuits. Its primary role is to distribute a high-speed differential clock to multiple loads without routing every branch directly from the clock source.
The 1:8 fanout ratio allows a single differential source to feed eight output branches, reducing the number of separate external buffer channels required in a high-speed system. The 1.5 GHz operating capability supports demanding communications, networking, test-and-measurement, and data-processing equipment. The exposed pad provides a thermal and electrical connection to the PCB copper area, which is important when distributing a fast-edge signal across a 32-pin surface-mount footprint.
The input termination architecture accepts either AC- or DC-coupled signals without placing termination components in the main signal path. This simplifies source interfacing while preserving low-amplitude operation. Output rise and fall times below 220 ps help maintain useful timing margin in systems with short clock periods. Differential clock distribution can also reduce sensitivity to common-mode noise when the source and receiving circuits are designed for matched differential operation.
Typical uses include server and network-interface clock distribution, backplane clock fanout, high-speed test equipment, telecommunications line cards, and FPGA or ASIC clock trees. In an FPGA design, the buffer can provide isolated branch clocks while limiting fanout loading on the source. In a communication card, it can distribute a common reference or recovered clock across multiple parallel processing channels.
Layout is critical because fast edges and differential clock signals can produce reflections, crosstalk, and supply-dependent timing errors. Route the differential pair over a continuous reference plane, use symmetrical geometry, minimize stubs, and provide a solid ground path. Decoupling should be placed close to the supply and ground pins. Review output spacing, return paths, and layer transitions in the manufacturer’s recommended layout before releasing the PCB.
This product page consolidates the device’s clock ratio, frequency, signaling, package, lifecycle, and replacement information with practical guidance for differential routing and thermal design. It also distinguishes verified functional equivalents from broader component-level alternatives so engineers can assess compatibility before changing an existing 32-pin layout.
Mga alternatibo na pwedeng ilagay na SY89202UMI — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
SY89202UMG-TR
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
SY89202UMG
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
SY89202UMI-TR
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
8S89202BKILFT
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
8S89202BKILF
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
8S89202BKILF/W
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
SY89202UMI Mga Spesipikasyon
| Product Type | Clock fanout buffer, divider, and multiplexer IC |
| Fanout Ratio | 1:8 |
| Maksimum na Taktiko ng Oras | 1.5 GHz |
| Packhaging | 32-pin VFQFN with exposed pad |
| Input Signal | Differential AC- or DC-coupled input |
| Minimum Input Signal | 100 mV, equivalent to 200 mVpp |
| Input Termination Architecture | 3-pin architecture without external termination resistors in the signal path |
| Output Logic Level | 800 mV LVPECL-compatible |
| Maximum Output Rise/Fall Time | Less than 220 ps |
| Bilang ng Outputs | 8 outputs |
| Uri ng Pagpapasok | Surface mount |
Gabay sa Pin Configuration ng SY89202UMI 32-pin vfqfn with exposed pad
Pin configuration para sa SY89202UMI (32-pin vfqfn with exposed pad package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa SY89202UMI.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
SY89202UMI ay nararapat para sa 6 aplikasyons: Network Interface Clock Distribution, FPGA and ASIC Clock Trees, Telecommunications Line Cards, Server Platform Clock Distribution, High-Speed Test and Measurement, Industrial Data Acquisition.
Network Interface Clock Distribution
The SY89202UMI fits network-interface designs that must distribute one differential clock across multiple serial, processor, or transceiver branches. Its 1:8 fanout provides eight 800 mV LVPECL-compatible outputs, while the 1.5 GHz capability covers high-speed communication data paths. The input can operate as low as 100 mV, or 200 mVpp, which is useful when the source has limited amplitude. Place the buffer near the clock source, keep the differential input route short, and give each output a controlled termination and return path to preserve signal integrity.
Inirekomenda
FPGA and ASIC Clock Trees
The SY89202UMI is suitable for FPGA or ASIC clock trees where a single differential source must feed multiple internal or external clock domains. The 1:8 fanout reduces the need for repeated source-buffer stages, while rise and fall times below 220 ps provide a fast, low-skew output. The 32-VFQFN exposed pad should be connected to a solid ground or supply plane with short thermal vias. Verify the receiving device’s clock-input thresholds, maximum input frequency, and allowable divider or bypass mode before assigning each output.
Inirekomenda
Telecommunications Line Cards
The SY89202UMI can distribute a common or recovered clock across parallel channels in telecommunications line cards and optical-network equipment. Its differential input accepts AC- or DC-coupled sources down to 100 mV, or 200 mVpp, without an external termination resistor network in the signal path. Eight LVPECL-compatible outputs support parallel clock branches, and operation up to 1.5 GHz accommodates high-speed line-card processing. Control impedance, minimize branch stubs, and maintain equal routing lengths where skew-sensitive circuitry requires matched clock arrivals.
Inirekomenda
Server Platform Clock Distribution
The SY89202UMI is applicable in server platforms that distribute a common reference clock to processors, fabric, SerDes blocks, or interface controllers. A 1:8 fanout supplies eight low-jitter LVPECL-compatible branches from one differential input, and the 1.5 GHz rating supports high-speed system timing. Because the package includes an exposed pad, use a continuous reference plane and adequate via stitching to reduce inductance. Check each receiver’s termination scheme and keep clock branches electrically isolated to prevent crosstalk and unintended loading.
Inirekomenda
High-Speed Test and Measurement
The SY89202UMI can provide synchronized clock branches in high-speed test equipment, oscilloscope subsystems, and automated measurement platforms. Its eight 800 mV LVPECL-compatible outputs and sub-220 ps edge rate support distribution of a common clock to multiple acquisition or timing channels. The small differential input amplitude tolerance also simplifies adaptation of low-amplitude source circuits. For best performance, preserve differential coupling, use low-loss routing, provide uninterrupted reference planes, and verify that channel skew and jitter remain within the instrument’s calibration budget.
Inirekomenda
Industrial Data Acquisition
The SY89202UMI supports industrial data-acquisition systems that synchronize multiple converters, processors, or communication blocks from one clock source. The 1:8 fanout allows eight branches to be distributed from a single differential input, while the 1.5 GHz maximum frequency accommodates demanding sampling and processing subsystems. Use short, symmetric routing and provide a continuous ground reference beneath the pair. Account for the exposed pad when defining the thermal design, and verify that the system’s ground reference and source amplitude remain within the clock input’s operating limits.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for SY89202UMI — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | SY89202UMG-TR | SY89202UMG | SY89202UMI-TR |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
Pangunahing mga Pagkakaiba
- Directly documented pin-and-package replacement (kumpara saSY89202UMG-TR)
- Eight-way clock distribution from one differential input (kumpara sa8S89202BKILFT)
- Fast LVPECL-compatible output edges (kumpara sa8S89202BKILF)
- Low-amplitude AC- or DC-coupled input support (kumpara saSY89202UMG)
Talaan ng Disenyo
Route the differential clock input as a short, impedance-controlled pair over a continuous reference plane. Avoid branch stubs and unnecessary test pads because the SY89202UMI can produce output edges faster than 220 ps. Keep the pair geometry symmetric, avoid crossing plane boundaries when practical, and place any input termination or coupling components close to the clock source. The manufacturer’s three-pin termination architecture eliminates a separate signal-path resistor network, but it does not remove the need to verify source common-mode voltage and input limits.
Provide the 32-VFQFN exposed pad with a low-impedance connection to the appropriate plane and a dense array of short thermal and electrical vias. Keep supply and ground connections short, place local decoupling at the device pins, and avoid placing high-speed clock routes beneath noisy converter or digital power paths. If all eight outputs are used, maintain adequate spacing between output pairs and provide continuous return paths to reduce crosstalk, especially where clock branches fan out near sensitive receivers.
Do not substitute the device solely because the package drawing and fanout ratio match. Confirm the exact ordering suffix, electrical limits, operating-temperature grade, output configuration, and lifecycle status. The product is identified as end-of-life, so production planning should include traceability, date-code requirements, approved alternate sourcing, and a last-time-buy decision where appropriate. For replacement assemblies, compare every pin name and supply connection against the manufacturer pin-description table rather than relying on a generic QFN-32 footprint.
Account for source-to-output delay, output-to-output skew, and jitter when allocating timing margin in the receiving system. The output edge rate is guaranteed below 220 ps, so excessive connector launches, long traces, or poorly terminated loads can dominate device jitter and produce reflections. Use controlled-impedance routing, appropriate LVPECL-compatible terminations, matched output geometry, and receiver thresholds consistent with 800 mV signaling. Validate the assembled board with clock-quality measurements when system timing is critical.
Impormasyon ng Pagsunod sa Kautusan
The SY89202UMI is a clock and timing integrated circuit rather than an automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering code.