TLV2341ID - Programmable Low-Voltage Op Amp | Texas Instruments
MPN: TLV2341ID ✓ NakahandaTLV2341ID Ulas
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its differential inputs while providing high input impedance and low output impedance. The TLV2341 belongs to the broader hierarchy of operational amplifier, analog amplifier, signal-conditioning IC, and semiconductor. Its common-mode input range extends below the negative supply rail and toward the positive rail at 25°C, giving it useful flexibility in systems whose signals operate close to 0 V. Its output-voltage range also includes negative values under suitable supply and loading conditions.
The TLV2341's principal system feature is programmable supply current. Texas Instruments specifies selectable supply-current settings of 17 µA, 250 µA, and 1.5 mA. These settings correspond to slew-rate specifications from 0.02 V/µs to 2.1 V/µs at a 3 V supply. A low-current setting favors power-sensitive operation, while a higher-current setting provides greater dynamic capability. The maximum supply voltage is 8 V, and the device is expressly characterized at 3 V and 5 V, allowing designers to optimize speed and consumption for each operating condition.
The amplifier is particularly well suited to low-voltage single-supply designs because its input and output capabilities support signal levels near the supply rails. These characteristics are useful in portable measurement systems, low-cost sensor interfaces, battery monitoring, and control loops where a larger operating range would add unnecessary power or cost. Input bias current, offset voltage, bandwidth, noise density, output-current capability, and temperature-range details should be confirmed against the manufacturer datasheet for the exact operating conditions.
Because the TLV2341 can operate from a single positive supply while accepting signals near ground, its output and input common-mode behavior must be checked with the chosen supply voltage, load, and temperature. The programmable supply-current pin should be driven only with valid logic levels, and unused inputs should be terminated according to the datasheet guidance. Decoupling capacitors should be placed close to the supply pins, with the exact capacitance and stability requirements taken from the manufacturer's recommended application circuit.
This page combines manufacturer specifications, a parameter-by-parameter comparison, application guidance, and same-footprint replacement guidance. It is designed to help engineers distinguish genuine drop-in options from devices that merely share the SOIC outline but differ in supply-current programming, bandwidth, common-mode behavior, or electrical limits.
Mga alternatibo na pwedeng ilagay na TLV2341ID — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
TLV2316ID
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
TLV2317ID
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
TLV2318ID
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
TLV2319ID
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
TLV9101ID
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
TLV2341ID Mga Pinakamataas na Rating at Electrical Characteristics
| Amplifier Type | Programmable low-voltage operational amplifier |
| Number of Channels | 1 channel |
| Supply Voltage Range | 2 V to 8 V |
| Fully Characterized Supply Voltage | 3 V and 5 V |
| Maximum Supply Voltage | 8 V |
| Programmable Supply Current Setting 1 | 17 µA |
| Programmable Supply Current Setting 2 | 250 µA |
| Programmable Supply Current Setting 3 | 1.5 mA |
| Slew Rate at 3 V, Low-Current Setting | 0.02 V/µs |
| Slew Rate at 3 V, High-Current Setting | 2.1 V/µs |
| Common-Mode Input Range | Extends below the negative rail and up to VDD at 25°C |
| Hanay ng Output Volte | Includes negative output voltage |
| Process Technology | Silicon-gate LinCMOS |
| Packhaging | 8-pin SOIC |
| Uri ng Pagpapasok | Surface mount |
Gabay sa Pin Configuration ng TLV2341ID 8-pin soic
Pin configuration para sa TLV2341ID (8-pin soic package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa TLV2341ID.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
TLV2341ID ay nararapat para sa 6 aplikasyons: Battery-Powered Sensor Interface, Portable Measurement Front End, Low-Voltage Current Sensing, Industrial Control and Sensor Conditioning, Low-Power Audio and Communication Buffering, Programmable Low-Power Analog System.
Battery-Powered Sensor Interface
The TLV2341ID fits low-energy sensor interfaces because it operates from 2 V to 8 V and lets the designer select 17 µA, 250 µA, or 1.5 mA supply current. Place it in a noninverting or inverting amplifier stage ahead of an ADC, using the 17 µA setting when battery life is critical. Its input common-mode range extending below the negative rail and toward VDD at 25°C is useful when the sensor signal sits close to ground. Confirm input bias current and offset voltage against the sensor source impedance, and verify output swing for the selected supply and load.
Inirekomenda
Portable Measurement Front End
Portable measurement systems benefit from the TLV2341ID's selectable supply-current levels, which allow a direct tradeoff between response speed and energy use. A 3 V system can operate at 0.02 V/µs for minimum consumption or up to 2.1 V/µs when faster transitions are needed. Use the amplifier to condition a low-level transducer signal before conversion or transmission. Its single-supply orientation simplifies portable instrumentation, while the common-mode range helps preserve signals near ground; output loading, input bias error, and noise must still be checked for the selected operating point.
Inirekomenda
Low-Voltage Current Sensing
The TLV2341ID can amplify a small shunt-derived voltage in a low-voltage current-sense circuit while preserving operation close to ground. The selectable 17 µA to 1.5 mA supply-current range permits power tuning after the required signal bandwidth is known. Configure the amplifier for the required gain, keep trace resistance low around the sense node, and verify common-mode limits over the full measured-current range. The manufacturer data characterizes operation at 3 V and 5 V, making these rails convenient baselines for design calculations.
Inirekomenda
Industrial Control and Sensor Conditioning
For a 5 V industrial control node, the TLV2341ID provides a single-supply amplifier with three supply-current choices for adapting to channel loading and update rate. A 250 µA setting offers a middle ground between the 17 µA low-power mode and the 1.5 mA high-drive mode. Use it to buffer a controller input, amplify a bridge or resistive sensor, or drive a feedback network. Its extended common-mode capability is valuable near the lower rail, but designers should verify input and output behavior at the actual temperature, supply tolerance, and load.
Inirekomenda
Low-Power Audio and Communication Buffering
The TLV2341ID can serve as a low-voltage buffer or gain stage in compact audio and communication equipment where supply consumption must be controlled. The 17 µA operating mode reduces system power, while the 250 µA and 1.5 mA modes provide greater slew capability for changing signal levels. Because this is a general-purpose low-voltage amplifier rather than an audio-specific device, verify output swing, distortion, noise, and stability for the actual load impedance and signal bandwidth. Grounding and decoupling layout are especially important when small signals pass through a common mixed-signal board.
Inirekomenda
Programmable Low-Power Analog System
The TLV2341ID is especially useful when one analog channel must adapt to multiple operating modes. The supply-current program can be raised for faster settling during measurement or lowered during standby, reducing the need for multiple amplifier variants. Set the programming pin only after checking its valid logic thresholds in the manufacturer datasheet. Provide local supply bypassing and avoid long high-impedance routes at the input. If the system needs greater fixed bandwidth, the TLV9101 family's 1.1 MHz gain-bandwidth product may be considered after a full stability and power comparison.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for TLV2341ID — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | TLV2316ID | TLV2317ID | TLV2318ID | TLV2319ID | TLV9101ID |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
Pangunahing mga Pagkakaiba
- Three selectable supply-current modes (kumpara saTLV2316ID)
- Higher fixed gain-bandwidth product in the TLV9101 family (kumpara saTLV9101ID)
- Single-supply characterization at both 3 V and 5 V (kumpara saTLV2317ID)
Talaan ng Disenyo
Choose the TLV2341ID supply-current mode from the required settling speed and system power budget rather than treating all three settings as interchangeable. The manufacturer lists 17 µA, 250 µA, and 1.5 mA modes, corresponding to 0.02 V/µs through 2.1 V/µs slew rate at 3 V. Confirm the programming-pin voltage, valid logic state, load current, and minimum pulse width in the datasheet before using the control signal. State changes should occur while the amplifier is in a controlled operating condition.
Place the supply-bypass capacitor close to the positive and ground pins, and keep the amplifier input, feedback components, and sensitive source nodes away from switching paths. For low-current operation, long PCB traces can add leakage and resistance that disturb the intended power budget; for high-current operation, inadequate trace width can cause voltage loss and heating. Follow the manufacturer recommended layout and use the documented capacitance and ESR considerations when configuring the output feedback network.
Do not assume that the full 2 V to 8 V input range provides identical behavior at every supply voltage. The device is fully characterized at 3 V and 5 V, and input common-mode and output swing can vary with supply, temperature, load, and current setting. Check the exact operating point against the datasheet limits, especially when signals approach the negative rail or the positive supply rail. Avoid substituting a fixed-current amplifier without reassessing the programming pin.
For very low-frequency or high-impedance sensor interfaces, evaluate input bias-current error across temperature rather than relying only on nominal offset voltage. The input impedance seen from the source and any feedback-network resistance can create gain errors, and capacitive loading can affect settling. Keep the input path short, use practical resistor values, and verify the complete gain-versus-frequency response at the selected 17 µA, 250 µA, or 1.5 mA setting.
Impormasyon ng Pagsunod sa Kautusan
Compliance status was not stated in the product-page, datasheet-index, distributor, or cross-reference information. AEC-Q100 qualification is not inferred from the industrial or general-purpose description.