TLV2374IN - Quad 3MHz RRIO Op Amp | Texas Instruments
MPN: TLV2374IN ✓ NakahandaTLV2374IN Ulas
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The TLV2374 belongs to the rail-to-rail-input/output operational amplifier family within the broader amplifier IC and semiconductor hierarchy. Rail-to-rail inputs let the amplifier operate close to the supply rails, while rail-to-rail output improves output-voltage range and signal headroom in low-voltage systems.
Each of the four amplifier channels combines a 3 MHz gain-bandwidth product with approximately 550 uA of quiescent current per channel. The device supports single-supply operation from 2.7 V through 16 V and provides approximately 2 V/us of slew rate. These characteristics make it useful for portable instrumentation, sensor signal conditioning, buffer stages, and low-voltage analog systems where four amplifier channels are required in one package.
The quad configuration provides four independent amplifiers while reducing package count compared with four separate single or dual devices. Common applications include amplifying outputs from pressure, temperature, current, and resistance sensors; buffering ADC inputs; driving low-capacitance analog stages; and amplifying low-frequency waveforms. Rail-to-rail input behavior is particularly useful when signals approach the lower or upper supply rail.
The TLV2374IN is packaged in a through-hole 14-pin PDIP. Unlike low-power micropower amplifier families optimized for kilohertz or low-hertz signals, its 3 MHz bandwidth provides greater margin for signal shaping, filtering, and general-purpose analog conditioning. System designers should still account for input and output common-mode limits, output-current capability, capacitive-load stability, supply bypass capacitance, and the operating temperature grade of the specific ordering code.
For PCB implementation, place the supply bypass capacitor close to the positive and negative supply pins, maintain short feedback paths, and verify settling behavior with the actual source impedance and load. This page combines the manufacturer’s device characteristics with package-specific guidance, application-oriented design notes, and drop-in replacement analysis for engineers evaluating the TLV2374IN.
Mga alternatibo na pwedeng ilagay na TLV2374IN — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok TLV2374IN (parehas na form factor at footprint) — pagkakaiba sa Mounting Type, Slew Rate.
TLV2374IP
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
TLV2374CN
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
TLV2374IN Mga Pinakamataas na Rating at Electrical Characteristics
| Number of Amplifier Channels | 4 channels |
| Amplifier Type | Single-supply operational amplifier |
| Gain-Bandwidth Product | 3 MHz |
| Minimum Operating Supply Voltage | 2.7 V |
| Maximum Recommended Supply Voltage | 16 V |
| Kuru-kuryente ng Kapayapaan | Approximately 550 uA per channel |
| Slew Rate | 2 V/us |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Operating Temperature Class | Extended industrial temperature range |
| Package Type | 14-pin PDIP |
| Uri ng Pagpapasok | Through-hole |
| Bilang ng Pins | 14 pins |
| Product Family | TLV237x operational amplifier series |
| Supplier Configuration | Quad amplifier with four independent channels |
Pin Configuration ng TLV2374IN
| Pin 1 | OUT1 — Output of amplifier 1 |
| Pin 2 | IN1- — Inverting input of amplifier 1 |
| Pin 3 | IN1+ — Non-inverting input of amplifier 1 |
| Pin 4 | V+ — Positive supply voltage |
| Pin 5 | IN2+ — Non-inverting input of amplifier 2 |
| Pin 6 | IN2- — Inverting input of amplifier 2 |
| Pin 7 | OUT2 — Output of amplifier 2 |
| Pin 8 | OUT3 — Output of amplifier 3 |
| Pin 9 | IN3- — Inverting input of amplifier 3 |
| Pin 10 | IN3+ — Non-inverting input of amplifier 3 |
| Pin 11 | V- — Negative supply voltage |
| Pin 12 | IN4+ — Non-inverting input of amplifier 4 |
| Pin 13 | IN4- — Inverting input of amplifier 4 |
| Pin 14 | OUT4 — Output of amplifier 4 |
Tipikal na mga Gamit
TLV2374IN ay nararapat para sa 6 aplikasyons: Low-Voltage Sensor Signal Conditioning, Precision ADC Input Buffer, Industrial Process Measurement, Portable Medical Monitoring, Low-Voltage Data Acquisition, Low-Frequency Filter and Buffer Stage.
Low-Voltage Sensor Signal Conditioning
The TLV2374IN is suitable for conditioning sensor outputs in 2.7 V to 16 V systems because each channel supports rail-to-rail input operation. Its approximately 550 uA quiescent current per channel helps control consumption in battery-powered instrumentation, while the 3 MHz gain-bandwidth product allows modest gain and filtering stages. A typical implementation buffers a sensor output before conversion by an ADC. The designer should account for sensor output impedance, ADC input capacitance, and the amplifier’s settling requirements.
Inirekomenda
Precision ADC Input Buffer
The TLV2374IN can provide four independent input buffers for moderately fast ADC front ends. Rail-to-rail input behavior is useful when the converter’s valid input range extends near either supply rail, and the 3 MHz gain-bandwidth product gives more bandwidth than typical low-power micropower amplifiers. Use the device as a voltage follower when isolation is more important than voltage gain. Validate acquisition time, capacitive loading, and output settling against the ADC requirements.
Inirekomenda
Industrial Process Measurement
The TLV2374IN suits process-measurement circuits that amplify small signals from resistive bridges, current sensors, and industrial transducers. Four channels reduce the number of packages required for a multi-input measurement board, while rail-to-rail input operation increases usable range in low-voltage systems. The 3 MHz bandwidth is adequate for many low- to moderate-bandwidth measurements. Common-mode voltage, transient protection, grounding, and input filtering must be addressed separately from the amplifier selection.
Inirekomenda
Portable Medical Monitoring
The TLV2374IN is appropriate for compact monitoring modules that process low-frequency physiological or diagnostic sensor signals from a 2.7 V or 3.3 V supply. Approximately 550 uA of quiescent current per channel helps limit power demand, and four channels support simultaneous signal conditioning without requiring four separate packages. Rail-to-rail inputs improve headroom when sensor outputs occupy much of the available voltage range. Medical designs must also evaluate isolation, leakage, safety, and application-specific standards separately.
Inirekomenda
Low-Voltage Data Acquisition
The TLV2374IN provides four channels for multiplexing or buffering multiple low-voltage data-acquisition inputs. Its 3 MHz gain-bandwidth product allows useful closed-loop bandwidth for moderate-speed acquisition, and the low quiescent current supports compact embedded systems. A practical design can use two channels for differential inputs and two for instrumentation or reference buffering. Confirm amplifier settling at the selected closed-loop gain and design the anti-alias filter independently to avoid noise or stability problems.
Inirekomenda
Low-Frequency Filter and Buffer Stage
The TLV2374IN can implement active filters, sample-and-hold buffers, and gain stages around slow or moderate-bandwidth signals. Its 3 MHz bandwidth provides useful loop gain above the signal band, while approximately 2 V/us slew rate helps preserve large-signal behavior. Four channels allow related filtering functions to share one package. Component tolerances, input bias-current effects, output loading, and capacitor stability should be evaluated during simulation rather than inferred only from the gain-bandwidth value.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for TLV2374IN — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | TLV2374IP | TLV2374CN |
|---|---|---|---|
| Package | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Amplifier Channels | 4 channels | 4 channels | 4 channels |
| Gain-Bandwidth Product | 3 MHz | 3 MHz | 3 MHz |
| Operating Supply Range | 2.7 V to 16 V | 2.7 V to 16 V | 2.7 V to 16 V |
| Quiescent Current | Approximately 550 uA per channel | Approximately 550 uA per channel | Approximately 550 uA per channel |
| Slew Rate | 2 V/us | 2 V/us | 2 V/us |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Ordering-Code Temperature Option | IN ordering code | IP ordering code | CN ordering code |
Pangunahing mga Pagkakaiba
- Four independent 3 MHz amplifier channels in one through-hole package (kumpara saTLV2374IP)
- Rail-to-rail input and output operation in a low-voltage device (kumpara saTLV2374CN)
- Low quiescent current without sacrificing 3 MHz bandwidth (kumpara saTLV2374IP)
Talaan ng Disenyo
Place the supply bypass capacitor close to pins 4 and 11, and keep the ground return path short to reduce supply noise and output instability. Route feedback components close to their associated amplifier pins so parasitic capacitance does not add unwanted poles. For sensitive measurements, keep analog input and output traces away from switching nodes and high-current return paths.
Validate settling time with the actual feedback network and ADC input capacitance. A 3 MHz gain-bandwidth product does not by itself guarantee adequate acquisition time at high closed-loop gain or with a large capacitive load. Add an isolation resistor when required by the amplifier stability guidance, and verify the complete input-to-output step response during prototype testing.
Do not assume rail-to-rail operation eliminates input common-mode restrictions under every output condition. The usable input range can depend on output voltage, supply level, and channel configuration. Review the manufacturer’s electrical-characteristics plots for the intended gain, output level, supply voltage, and temperature before selecting input and feedback values.
Impormasyon ng Pagsunod sa Kautusan
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was established for this ordering code. The TLV2374 family supports industrial-temperature operation, but the standard TLV2374IN is not identified as an AEC-Q100-qualified automotive variant.