TLV2470CP - 6V, 2.8MHz RRIO Op Amp | Texas Instruments
MPN: TLV2470CP ✓ NakahandaTLV2470CP Ulas
A rail-to-rail input/output operational amplifier is an analog amplifier whose input common-mode voltage and output swing can extend toward the positive and negative supply rails. This makes it useful when a sensor, converter, or mixed-signal node operates close to the available supply voltage. Within the broader hierarchy of analog and mixed-signal ICs, the TLV2470CP is a low-voltage CMOS operational amplifier intended for portable, industrial-control, instrumentation, and general-purpose signal-conditioning applications.
The TLV2470CP provides 2.8 MHz gain-bandwidth product, rail-to-rail input and output behavior, shutdown support, and approximately 600 µA per channel supply current. The 6 V maximum supply voltage allows operation from low-voltage rails commonly used in portable and embedded equipment. Its low-current operating point is particularly useful for battery-powered monitoring systems, while the 2.8 MHz bandwidth supports moderate-frequency amplification, active filtering, and buffering.
The 8-pin PDIP package provides through-hole assembly compatibility and a conventional DIP footprint. The shutdown function can reduce power consumption when the amplifier is not needed, although the complete logic truth table and timing limits must be taken from the manufacturer datasheet. Because operating current and common-mode behavior depend on supply voltage and configuration, the datasheet characteristic curves should be consulted before setting gain, output loading, or input bias assumptions.
Typical uses include low-power sensor conditioning, buffered transducers, portable measurement systems, audio input stages, motor or actuator monitoring, and industrial control modules. The amplifier can operate near its supply rails, making it appropriate for systems whose signals occupy much of the available input range. Designers should still verify output swing at the required load and frequency before relying on full rail-to-rail performance.
Decoupling, input biasing, and shutdown sequencing are the principal implementation considerations. Place the supply bypass capacitor close to the device, keep sensitive input traces short, and avoid allowing input or output pins to exceed the electrical limits stated in the manufacturer datasheet. This page combines package, electrical, lifecycle, replacement, and application guidance to support initial design selection and PCB planning.
Mga alternatibo na pwedeng ilagay na TLV2470CP — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok TLV2470CP (parehas na form factor at footprint).
TLV2470IP
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →TLV2470AIP
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
TLV2470CP Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | Single CMOS operational amplifier |
| Number of Channels | 1 channel |
| Maximum Supply Voltage | 6 V |
| Gain-Bandwidth Product | 2.8 MHz |
| Kuru-kuryente ng Pagbibigay | 600 µA per channel |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Shutdown Function | Supported |
| Packhaging | PDIP-8, 0.300 inch body width |
| Bilang ng Pin | 8 pins |
| Lead Pitch | 7.62 mm |
| Hanay ng Temperature na Operasyon | 0 °C to 70 °C |
| Uri ng Pagpapasok | Through-hole |
Pin Configuration ng TLV2470CP
| Pin 1 | NC — Not connected |
| Pin 2 | IN+ — Non-inverting input |
| Pin 3 | IN− — Inverting input |
| Pin 4 | OUT — Amplifier output |
| Pin 5 | V+ — Positive supply voltage |
| Pin 6 | V− — Negative supply voltage or ground in single-supply operation |
| Pin 7 | SD — Shutdown control input |
| Pin 8 | NC — Not connected |
Tipikal na mga Gamit
TLV2470CP ay nararapat para sa 6 aplikasyons: Battery-Powered Sensor Conditioning, Portable Instrumentation, Industrial Control and Monitoring, Low-Level Audio Input, Active Filtering and Signal Conditioning, Data Acquisition Front End.
Battery-Powered Sensor Conditioning
The TLV2470CP fits low-power sensor interfaces because it combines approximately 600 µA of supply current per channel with rail-to-rail input and output operation. A bridge sensor, resistive element, or low-level transducer can be amplified close to the measured signal without requiring a separate mid-supply reference when the source operates near a supply rail. The 2.8 MHz gain-bandwidth product also permits moderate-frequency filtering and gain stages, although input bias current, noise, and output settling must be checked against the sensor impedance. Shutdown control can reduce consumption during inactive sampling intervals, making rail budgeting and logic sequencing important.
Inirekomenda
Portable Instrumentation
Portable instrumentation benefits from the TLV2470CP's 6 V maximum supply, approximately 600 µA per channel consumption, and 2.8 MHz gain-bandwidth product. It can buffer sensor inputs, amplify low-level analog signals, or implement an active filter where higher bandwidth is unnecessary. Rail-to-rail input behavior reduces the need to center signals around mid-supply, while rail-to-rail output improves usable signal range. For handheld instruments, verify the amplifier's offset, drift, noise, and output behavior across the intended temperature range, and use the shutdown function only after confirming its logic and transition behavior in the manufacturer datasheet.
Inirekomenda
Industrial Control and Monitoring
The TLV2470CP is applicable to industrial monitoring modules that process slowly changing or moderate-bandwidth analog signals from pressure, position, and equipment-condition sensors. Its 2.8 MHz gain-bandwidth product supports practical low-frequency amplification and filtering, and the 600 µA per channel operating current can help control consumption in distributed sensor nodes. The PDIP-8 package simplifies through-hole assembly and repair. Industrial designs should nevertheless verify the exact operating temperature range, which is specified as 0 °C to 70 °C for this ordering option, and assess whether transient protection, grounding, and supply isolation need additional components.
Inirekomenda
Low-Level Audio Input
The TLV2470CP can serve as a low-level audio input amplifier when the design prioritizes low supply current and accepts a 2.8 MHz bandwidth ceiling. Rail-to-rail inputs allow source signals to occupy a large portion of a low-voltage supply, and the shutdown input can disable the amplifier during inactive listening or test states. Its rail-to-rail output is useful for driving a following ADC or mixer stage within the available voltage range. Audio engineers should evaluate noise, distortion, input impedance, output loading, and gain stability at the target frequency because these characteristics determine whether the amplifier is suitable for microphone, line, or headphone-adjacent signal paths.
Inirekomenda
Active Filtering and Signal Conditioning
The 2.8 MHz gain-bandwidth product of the TLV2470CP supports moderate-frequency active filters, integrators, and general-purpose signal-conditioning networks. Because it is a single amplifier with rail-to-rail input and output stages, it can implement gain, buffering, and active-filter functions in compact through-hole designs. Component selection should account for closed-loop gain, phase margin, and the effect of load capacitance; the manufacturer characteristic curves are necessary to determine practical stability. The approximately 600 µA per channel current also makes the device relevant to multi-stage filters where each added amplifier contributes to the total power budget.
Inirekomenda
Data Acquisition Front End
The TLV2470CP can precede an ADC in a compact data-acquisition front end where low voltage, low supply current, and near-rail signal handling are important. Its 2.8 MHz gain-bandwidth product provides more bandwidth than is needed for many slow sensor channels, while approximately 600 µA per channel supports distributed acquisition nodes. Rail-to-rail operation simplifies conditioning of converter or sensor outputs that do not sit near mid-supply. Designers must still verify settling time for the selected gain, output drive into the ADC's sampling network, input capacitance limits, and the effect of power-supply noise. The shutdown pin should be sequenced with the converter to avoid invalid intermediate states.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for TLV2470CP — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | TLV2470IP | TLV2470AIP |
|---|---|---|---|
| Package | PDIP-8 | PDIP-8 | PDIP-8 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Single CMOS operational amplifier | Single CMOS operational amplifier | Single CMOS operational amplifier |
Pangunahing mga Pagkakaiba
- Low-power operation with useful AC bandwidth (kumpara saTLV2470AIP)
- Shutdown support in a standard PDIP footprint (kumpara saTLV2470IP)
- Rail-to-rail signal handling in a 6 V device (kumpara saTLV2470AIP)
Talaan ng Disenyo
Route the TLV2470CP power and ground connections directly to the device, and place the supply bypass capacitor close to pins 5 and 6. Keep the IN+ and IN− traces short and away from high-current switching paths to minimize coupled noise. Because the device is available in a through-hole PDIP-8 package, preserve the 7.62 mm lead pitch and standard DIP land pattern when creating or revising PCB artwork.
Do not assume that every TLV247x package suffix has identical shutdown behavior. Confirm that pin 7 is driven only with a valid logic level and that unused inputs are not left floating. For single-supply operation, connect V− to ground and evaluate input and output common-mode limits at the required frequency and load. Also verify the 0 °C to 70 °C operating range of the TLV2470CP ordering option before using it outside that interval.
Check closed-loop stability, output settling, and capacitive-load drive before using the amplifier as a filter or ADC driver. The 2.8 MHz gain-bandwidth product is sufficient for many low-frequency conditioning stages but does not imply unlimited stability into heavy capacitive loads. Use the manufacturer gain-phase and output-capacitance curves, and place any isolation resistor close to the output if the driven load introduces excessive capacitive loading.
Budget the approximately 600 µA per-channel operating current together with shutdown-mode consumption and external-load requirements. The 6 V maximum supply rating does not indicate that every operating point is equally characterized; confirm minimum supply voltage and performance over the intended rail range. When shutdown is used for duty-cycled sensing, verify logic thresholds and startup settling before assuming the next conversion begins with a valid output.
Impormasyon ng Pagsunod sa Kautusan
Compliance status was not explicitly identified in the available product information. The TLV2470CP ordering option is specified for 0 °C to 70 °C operation and is not identified as an automotive-qualified variant.