Texas Instruments

TLV2470CP - 6V, 2.8MHz RRIO Op Amp | Texas Instruments

부품 번호: TLV2470CP ✓ 활성
6 V Vdss 600 µA per channel Id PDIP-8, 0.300 inch body width Package
MOQ: 1 |

TLV2470CP 개요

The Texas Instruments TLV2470CP is a single-rail operational amplifier with a 6 V maximum supply, 2.8 MHz gain-bandwidth product, rail-to-rail input and output operation, and shutdown capability. The device consumes 600 µA per channel and is offered in an 8-pin PDIP package. Its combination of low supply current, short operation, and broad input/output common-mode range supports compact, low-power signal-conditioning systems.

A rail-to-rail input/output operational amplifier is an analog amplifier whose input common-mode voltage and output swing can extend toward the positive and negative supply rails. This makes it useful when a sensor, converter, or mixed-signal node operates close to the available supply voltage. Within the broader hierarchy of analog and mixed-signal ICs, the TLV2470CP is a low-voltage CMOS operational amplifier intended for portable, industrial-control, instrumentation, and general-purpose signal-conditioning applications.

The TLV2470CP provides 2.8 MHz gain-bandwidth product, rail-to-rail input and output behavior, shutdown support, and approximately 600 µA per channel supply current. The 6 V maximum supply voltage allows operation from low-voltage rails commonly used in portable and embedded equipment. Its low-current operating point is particularly useful for battery-powered monitoring systems, while the 2.8 MHz bandwidth supports moderate-frequency amplification, active filtering, and buffering.

The 8-pin PDIP package provides through-hole assembly compatibility and a conventional DIP footprint. The shutdown function can reduce power consumption when the amplifier is not needed, although the complete logic truth table and timing limits must be taken from the manufacturer datasheet. Because operating current and common-mode behavior depend on supply voltage and configuration, the datasheet characteristic curves should be consulted before setting gain, output loading, or input bias assumptions.

Typical uses include low-power sensor conditioning, buffered transducers, portable measurement systems, audio input stages, motor or actuator monitoring, and industrial control modules. The amplifier can operate near its supply rails, making it appropriate for systems whose signals occupy much of the available input range. Designers should still verify output swing at the required load and frequency before relying on full rail-to-rail performance.

Decoupling, input biasing, and shutdown sequencing are the principal implementation considerations. Place the supply bypass capacitor close to the device, keep sensitive input traces short, and avoid allowing input or output pins to exceed the electrical limits stated in the manufacturer datasheet. This page combines package, electrical, lifecycle, replacement, and application guidance to support initial design selection and PCB planning.

드롭인 대체품: TLV2470CP — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: TLV2470CP (동일 폼 팩터 및 풋프린트).

TLV2470IP

✅ 드롭인 ⚠️ 사양 미검증
Texas Instruments
📦 PDIP-8
호환 사양

가격 문의

데이터시트 보기 →

TLV2470AIP

✅ 드롭인
📦 PDIP-8
Same PDIP-8 footprint; enhanced-family electrical differences can reach approximately 10% under the stated parametric-match basis and require datasheet verification

📋 참조 대체품 (카탈로그에 없음)

TLV2470CP 최대 정격 & 전기적 특성

Product Type Single CMOS operational amplifier
Number of Channels 1 channel
Maximum Supply Voltage 6 V
Gain-Bandwidth Product 2.8 MHz
공급 전류 600 µA per channel
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Shutdown Function Supported
패키지 PDIP-8, 0.300 inch body width
핀 수 8 pins
Lead Pitch 7.62 mm
동작 온도 범위 0 °C to 70 °C
실장 유형 Through-hole

TLV2470CP 핀 구성

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
핀 1 NC — Not connected
핀 2 IN+ — Non-inverting input
핀 3 IN− — Inverting input
핀 4 OUT — Amplifier output
핀 5 V+ — Positive supply voltage
핀 6 V− — Negative supply voltage or ground in single-supply operation
핀 7 SD — Shutdown control input
핀 8 NC — Not connected

일반적인 애플리케이션

TLV2470CP 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Conditioning, Portable Instrumentation, Industrial Control and Monitoring, Low-Level Audio Input, Active Filtering and Signal Conditioning, Data Acquisition Front End.

🔋

Battery-Powered Sensor Conditioning

The TLV2470CP fits low-power sensor interfaces because it combines approximately 600 µA of supply current per channel with rail-to-rail input and output operation. A bridge sensor, resistive element, or low-level transducer can be amplified close to the measured signal without requiring a separate mid-supply reference when the source operates near a supply rail. The 2.8 MHz gain-bandwidth product also permits moderate-frequency filtering and gain stages, although input bias current, noise, and output settling must be checked against the sensor impedance. Shutdown control can reduce consumption during inactive sampling intervals, making rail budgeting and logic sequencing important.

📱

Portable Instrumentation

Portable instrumentation benefits from the TLV2470CP's 6 V maximum supply, approximately 600 µA per channel consumption, and 2.8 MHz gain-bandwidth product. It can buffer sensor inputs, amplify low-level analog signals, or implement an active filter where higher bandwidth is unnecessary. Rail-to-rail input behavior reduces the need to center signals around mid-supply, while rail-to-rail output improves usable signal range. For handheld instruments, verify the amplifier's offset, drift, noise, and output behavior across the intended temperature range, and use the shutdown function only after confirming its logic and transition behavior in the manufacturer datasheet.

🏭

Industrial Control and Monitoring

The TLV2470CP is applicable to industrial monitoring modules that process slowly changing or moderate-bandwidth analog signals from pressure, position, and equipment-condition sensors. Its 2.8 MHz gain-bandwidth product supports practical low-frequency amplification and filtering, and the 600 µA per channel operating current can help control consumption in distributed sensor nodes. The PDIP-8 package simplifies through-hole assembly and repair. Industrial designs should nevertheless verify the exact operating temperature range, which is specified as 0 °C to 70 °C for this ordering option, and assess whether transient protection, grounding, and supply isolation need additional components.

🎧

Low-Level Audio Input

The TLV2470CP can serve as a low-level audio input amplifier when the design prioritizes low supply current and accepts a 2.8 MHz bandwidth ceiling. Rail-to-rail inputs allow source signals to occupy a large portion of a low-voltage supply, and the shutdown input can disable the amplifier during inactive listening or test states. Its rail-to-rail output is useful for driving a following ADC or mixer stage within the available voltage range. Audio engineers should evaluate noise, distortion, input impedance, output loading, and gain stability at the target frequency because these characteristics determine whether the amplifier is suitable for microphone, line, or headphone-adjacent signal paths.

🔧

Active Filtering and Signal Conditioning

The 2.8 MHz gain-bandwidth product of the TLV2470CP supports moderate-frequency active filters, integrators, and general-purpose signal-conditioning networks. Because it is a single amplifier with rail-to-rail input and output stages, it can implement gain, buffering, and active-filter functions in compact through-hole designs. Component selection should account for closed-loop gain, phase margin, and the effect of load capacitance; the manufacturer characteristic curves are necessary to determine practical stability. The approximately 600 µA per channel current also makes the device relevant to multi-stage filters where each added amplifier contributes to the total power budget.

🖥️

Data Acquisition Front End

The TLV2470CP can precede an ADC in a compact data-acquisition front end where low voltage, low supply current, and near-rail signal handling are important. Its 2.8 MHz gain-bandwidth product provides more bandwidth than is needed for many slow sensor channels, while approximately 600 µA per channel supports distributed acquisition nodes. Rail-to-rail operation simplifies conditioning of converter or sensor outputs that do not sit near mid-supply. Designers must still verify settling time for the selected gain, output drive into the ADC's sampling network, input capacitance limits, and the effect of power-supply noise. The shutdown pin should be sequenced with the converter to avoid invalid intermediate states.

What is the operating voltage of TLV2470CP?
The TLV2470CP supports a maximum supply voltage of 6 V and is designed for low-voltage, single-supply operation. According to the Texas Instruments TLV2470 product page, the device is specified as a 6 V operational amplifier with rail-to-rail input and output behavior. Confirm the minimum operating voltage and individual supply-rail limits in the manufacturer datasheet before applying it to a new power rail.
What are the key specifications of TLV2470CP that engineers should know?
The TLV2470CP combines a 2.8 MHz gain-bandwidth product, approximately 600 µA of supply current per channel, rail-to-rail input and output operation, and shutdown capability in an 8-pin PDIP package. Texas Instruments describes it as a single, 6 V, low-power CMOS operational amplifier. These characteristics place it between general-purpose precision amplifiers and higher-bandwidth signal-chain devices.
Where can I download the TLV2470CP datasheet PDF?
The official TLV2470CP datasheet is available through Texas Instruments at https://www.ti.com/lit/gpn/TLV2470. It covers the TLV247x family, including electrical characteristics, pin functions, typical application circuits, and package drawings. The product-detail page at https://www.ti.com/product/TLV2470/part-details/TLV2470CP identifies TLV2470CP as the 8-pin PDIP ordering option.
Where can I find the TLV2470CP pinout?
The TLV2470CP pinout is shown in the Texas Instruments TLV2470 family datasheet at https://www.ti.com/lit/gpn/TLV2470. The PDIP version uses an 8-pin through-hole footprint with 7.62 mm lead spacing. Pin 2 is IN+, pin 3 is IN−, pin 4 is OUT, pin 5 is V+, pin 6 is V−, and pin 7 is the shutdown control; pins 1 and 8 are not connected.
Where to buy TLV2470CP online?
Use the Request a Quote form on this page to request TLV2470CP availability, MOQ, and current sourcing terms. The form allows buyers to specify the required quantity and package variant without relying on a static listing that may not reflect current inventory. The manufacturer part number for inquiry is TLV2470CP, and the device is specified in an 8-pin PDIP package.
What is the price of TLV2470CP?
Current TLV2470CP price and quantity availability should be obtained through the Request a Quote form on this page. The structured pricing area is refreshed independently of the technical description, allowing the inquiry to reflect current stock, order quantity, and market conditions. For design budgeting, confirm the quoted unit cost and minimum order quantity before releasing the component to production.
What is the lead time for TLV2470CP?
Submit TLV2470CP and your required quantity through the Request a Quote form on this page to obtain the current lead time. Lead time can vary with order size, scheduled production, packaging requirements, and inventory position, so a confirmed quotation is preferable to a historical catalog estimate. The inquiry should identify the exact 8-pin PDIP ordering code TLV2470CP.
Is TLV2470CP in stock?
Use the Request a Quote form on this page for the current TLV2470CP stock status and available quantity. Because inventory changes by package, order size, and sales channel, stock should not be inferred from an old product page. The form can also establish a lead time when no immediate allocation is available.
TLV2470CP vs TLV2470AIP - which is better for a low-power signal conditioner?
Choose TLV2470CP for a 6 V, 2.8 MHz, 600 µA-per-channel design that uses the legacy PDIP-8 ordering option, and evaluate TLV2470AIP when its enhanced specifications better match the application. Both are presented as PDIP-8 devices, but the manufacturer datasheet should be checked for any difference in shutdown behavior, slew rate, offset, or temperature coverage before exchanging them.
What is the difference between TLV2470CP and TLV2470IP?
TLV2470CP and TLV2470IP belong to the same Texas Instruments TLV247x family and use the same 8-pin PDIP footprint, making the IP variant relevant for a like-for-like design review. Their exact electrical limits and orderable status must be compared in the manufacturer datasheet. Confirm pin functions, supply current, shutdown polarity, and operating temperature requirements before treating the change as a drop-in replacement.
When should I choose TLV2470CP over TLV2470IP?
Choose TLV2470CP when the design specifically requires the 6 V, 2.8 MHz, low-power operational-amplifier function in the identified PDIP-8 configuration. Choose TLV2470IP only after comparing its manufacturer ratings against the TLV2470CP datasheet and confirming unchanged PCB connectivity. Pay particular attention to shutdown logic, offset, drift, slew rate, output drive, and temperature range.
Is TLV2470CP suitable for battery-powered sensor conditioning?
The TLV2470CP is suitable for many battery-powered sensor-conditioning designs because it operates from a low-voltage supply, consumes approximately 600 µA per channel, and offers rail-to-rail input and output operation. The shutdown pin can further reduce consumption when sensing is inactive. Validate input bias current, noise, output settling, and common-mode range for the selected sensor and measurement bandwidth.
What can replace TLV2470CP?
TLV2470IP is the closest same-package candidate to review for TLV2470CP because it belongs to the same TLV247x family and is offered in an 8-pin PDIP configuration. A replacement should not be selected by package name alone: verify pin-to-pin connectivity, shutdown polarity, supply range, bandwidth, slew rate, output drive, offset, noise, and temperature coverage against the target datasheet.
Is there a verified cross-brand drop-in equivalent for TLV2470CP?
No cross-brand part can be identified as a verified TLV2470CP drop-in equivalent from the available cross-reference results. A suitable candidate must use the 8-pin PDIP footprint, preserve shutdown and power-pin connectivity, and remain within the target's key electrical limits. Use the Request a Quote form on this page to discuss an existing approved cross-reference or an engineering substitution request.
How should TLV2470CP be used in a portable measurement system?
Place the TLV2470CP close to the sensor interface, connect the signal to pins 2 and 3, and use pin 4 for the conditioned output. The 2.8 MHz gain-bandwidth product supports moderate-frequency precision conditioning, while approximately 600 µA per channel suits low-power operation. Power pin 5 and ground pin 6 according to the datasheet, drive shutdown pin 7 with the required logic level, and bypass the supply near the device.

엔지니어링 참조 데이터: TLV2470CP — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose TLV2470CP for low-voltage systems needing one low-power, moderate-bandwidth amplifier with rail-to-rail input and output operation, shutdown control, and an 8-pin PDIP footprint. It is particularly suitable for portable sensing, industrial monitoring, active filtering, audio input conditioning, and ADC front ends where approximately 600 µA per channel and 2.8 MHz gain-bandwidth product fit the design. Review TLV2470IP when a same-family alternative may offer updated specifications or availability while retaining the PDIP footprint. Evaluate TLV2470AIP when its enhanced-family ratings could improve offset, noise, speed, or other parameters. Both alternatives require a full pin, electrical, and temperature comparison before substitution. No cross-brand part is presented as a verified drop-in replacement because package, shutdown logic, and key AC specifications must be demonstrated rather than inferred from a generic amplifier description.

대체품과의 비교

파라미터 이 제품 TLV2470IP TLV2470AIP
Package PDIP-8 PDIP-8 PDIP-8
Brand Texas Instruments Texas Instruments Texas Instruments
Product Type Single CMOS operational amplifier Single CMOS operational amplifier Single CMOS operational amplifier

주요 차별점

  • Low-power operation with useful AC bandwidth (vs TLV2470AIP)
  • Shutdown support in a standard PDIP footprint (vs TLV2470IP)
  • Rail-to-rail signal handling in a 6 V device (vs TLV2470AIP)

설계 노트

Route the TLV2470CP power and ground connections directly to the device, and place the supply bypass capacitor close to pins 5 and 6. Keep the IN+ and IN− traces short and away from high-current switching paths to minimize coupled noise. Because the device is available in a through-hole PDIP-8 package, preserve the 7.62 mm lead pitch and standard DIP land pattern when creating or revising PCB artwork.

Do not assume that every TLV247x package suffix has identical shutdown behavior. Confirm that pin 7 is driven only with a valid logic level and that unused inputs are not left floating. For single-supply operation, connect V− to ground and evaluate input and output common-mode limits at the required frequency and load. Also verify the 0 °C to 70 °C operating range of the TLV2470CP ordering option before using it outside that interval.

Check closed-loop stability, output settling, and capacitive-load drive before using the amplifier as a filter or ADC driver. The 2.8 MHz gain-bandwidth product is sufficient for many low-frequency conditioning stages but does not imply unlimited stability into heavy capacitive loads. Use the manufacturer gain-phase and output-capacitance curves, and place any isolation resistor close to the output if the driven load introduces excessive capacitive loading.

Budget the approximately 600 µA per-channel operating current together with shutdown-mode consumption and external-load requirements. The 6 V maximum supply rating does not indicate that every operating point is equally characterized; confirm minimum supply voltage and performance over the intended rail range. When shutdown is used for duty-cycled sensing, verify logic thresholds and startup settling before assuming the next conversion begins with a valid output.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

Compliance status was not explicitly identified in the available product information. The TLV2470CP ordering option is specified for 0 °C to 70 °C operation and is not identified as an automotive-qualified variant.

데이터 검증일: 2026-11-15 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

TLV2470CP TLV2470CP datasheet TLV2470CP datasheet pdf TLV2470CP pinout TLV2470CP schematic TLV2470CP equivalent TLV2470CP replacement TLV2470CP vs TLV2470IP TLV2470CP price TLV2470CP stock Texas Instruments TLV2470CP TLV2470CP PDIP-8 pinout TLV2470CP 2.8MHz op amp TLV2470CP low power amplifier

관련 부품 & 용어

Texas Instruments TLV2470CP TLV2470IP TLV2470AIP TLV247x operational amplifier CMOS operational amplifier rail-to-rail input rail-to-rail output low-dropout analog signal conditioning shutdown control 2.8 MHz gain-bandwidth product 600 µA per channel 6 V power supply PDIP-8 DIP package family through-hole surface-mount package hierarchy single-supply operation active filter ADC front end battery-powered sensor conditioning industrial monitoring low-noise signal path
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기