TPS54218ARTER - 2A, 6V Sync Step-Down Buck Regulator | TI
MPN: TPS54218ARTER ✓ NakahandaTPS54218ARTER Ulas
A synchronous buck converter is a type of DC-DC switching regulator that replaces the freewheeling diode of a classic buck topology with an integrated second MOSFET, improving efficiency at low output voltages. Within the power-management hierarchy, it sits as a point-of-load voltage regulator IC, converting a higher intermediate bus voltage into a tightly regulated low-voltage rail for processors, FPGAs, and mixed-signal loads.
Key features include two integrated n-channel MOSFETs that reduce external component count, constant-frequency peak current-mode control that simplifies loop compensation and reduces output capacitance, and a wide programmable switching-frequency range of 200 kHz to 2 MHz that permits very small inductors. The adjustable output uses a 0.803 V feedback reference.
Technically, the peak current-mode architecture provides fast line and load transient response and cycles-by-cycle current limiting. The high switching capability enables single-digit-millihenry inductance values and a compact 3x3 mm power solution footprint, while integrated MOSFETs minimize switching-node parasitics.
Typical applications include point-of-load power for DSPs and FPGAs, 5 V or 3.3 V distributed-bus post-regulation in industrial controls, and telecom/networking line cards where a small 2 A POL buck is needed.
A key design consideration is that because this is a switching converter, PCB layout of the PH switching node, input decoupling, and ground return directly affects EMI and output ripple - keep the input capacitor loop minimal.
This page synthesizes verified distributor pricing, same-family drop-in alternatives, and practical design notes beyond the raw datasheet.
Mga alternatibo na pwedeng ilagay na TPS54218ARTER — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok TPS54218ARTER (parehas na form factor at footprint) — pagkakaiba sa Package, Topology, RoHS Status.
TPS54218RTER
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →TPS54218RTE
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →TPS54418ARTER
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
TPS54418RTER
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
TPS54218ARTER Mga Pinakamataas na Rating at Electrical Characteristics
| Topolohiya | Synchronous Step-Down (Buck) |
| Hanay ng Voltage ng Input | 2.95 V to 6 V |
| Maksimum na Current ng Output | 2 A |
| Type ng Output | Adjustable |
| Feedback Reference Voltage | 0.803 V |
| Switching Frequency Range | 200 kHz to 2 MHz |
| Control Architecture | Constant Frequency Peak Current Mode |
| Integrated MOSFETs | 2 x N-Channel (synchronous) |
| Bilang ng Outputs | 1 |
| Family | SWIFT (Low-Input-Voltage SWIFT) |
| Packhaging | 16-WFQFN Exposed Pad (RTE), 3 mm x 3 mm |
| Uri ng Pagpapasok | Surface Mount |
| Tindminan RoHS | Compliant (per distributor listings) |
| Product Status | Active |
Gabay sa Pin Configuration ng TPS54218ARTER 16-wfqfn exposed pad (rte), 3 mm x 3 mm
Pin configuration para sa TPS54218ARTER (16-wfqfn exposed pad (rte), 3 mm x 3 mm package). Ang power device na ito ay may gate, drain, at source terminals. Para sa mga non-polarized package, sumangguni sa datasheet ng manufacturer para sa eksaktong oryentasyon ng pin 1 at mga detalye ng footprint. Kasama sa mga karaniwang aplikasyon ang disenyo ng power supply, motor driving, at load switching.
Wala ng detalyadong pinout data na magagamit para sa TPS54218ARTER.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
TPS54218ARTER ay nararapat para sa 6 aplikasyons: Point-of-Load Power for DSPs and FPGAs, Industrial Automation Control Boards, Networking and Telecom Line Cards, Test and Measurement Instrumentation, Battery-Powered Portable Equipment, Security and Camera Systems.
Point-of-Load Power for DSPs and FPGAs
The TPS54218ARTER fits point-of-load conversion from a 3.3 V or 5 V intermediate rail down to sub-1 V core voltages for DSPs and FPGAs. Its 0.803 V feedback reference supports modern low-voltage cores, and the 2 A rating covers typical small-core or I/O rail loads. Constant-frequency peak current-mode control delivers fast load-transient response, which matters when a processor wakes from idle or clocks up. Operating at up to 2 MHz lets designers use small, low-DCR inductors in the 1 uH range, keeping the entire POL solution inside a few square millimeters next to the load. The 3x3 mm VQFN-16 with exposed pad provides low thermal impedance to the PCB, supporting full 2 A operation with a modest copper area. Place input ceramics within 2 mm of the VIN pin to minimize switch-node ringing and EMI.
Inirekomenda
Industrial Automation Control Boards
Industrial controllers frequently regulate 5 V backplane power into local 3.3 V, 2.5 V, or 1.8 V analog and digital rails. The TPS54218ARTER accepts the 2.95 V to 6 V input range directly, so it can post-regulate a noisy 5 V bus without an intermediate stage. Its current-mode architecture rejects input-line disturbances well, and integrated MOSFETs remove diode losses, raising efficiency in always-on factory equipment. The 200 kHz to 2 MHz frequency flexibility lets designers place switching harmonics away from sensitive analog front-end bands or push frequency high to shrink magnetics on dense I/O cards. Thermal performance of the exposed-pad VQFN-16 sustains 2 A in 70 C ambient enclosures with roughly 1 square inch of copper. The compact footprint suits modular PLC I/O cards and motor-control interface boards where board area is constrained.
Inirekomenda
Networking and Telecom Line Cards
Telecom and networking line cards convert a distributed 5 V rail into many local low-voltage supplies. The TPS54218ARTER addresses one 2 A rail per device, and its small 3x3 mm footprint allows multiple converters to be clustered near their loads, reducing distribution losses and plane complexity. The ability to synchronize via the RT/CLK pin lets several converters lock to a common clock, spreading EMI spectrum predictably across the card - valuable for passing system-level EMC tests. Constant on-time alternatives struggle with this; peak current mode naturally supports paralleling of transient budgets and clean sequencing. The adjustable 0.803 V-referenced output covers PHY, SERDES, and memory rails. Wide 2 MHz capability shrinks the inductor so that power sections fit under connector overhangs on height-limited cards.
Inirekomenda
Test and Measurement Instrumentation
Bench instruments and modular test hardware need low-ripple local rails for ADC, DAC, and clock circuitry. The TPS54218ARTER provides a well-controlled switching regulator whose fixed-frequency peak current-mode operation produces predictable ripple at the programmed switching frequency, which is easy to filter with a post-LC stage. Its 2 MHz capability pushes ripple content far above sensitive signal bands, simplifying filtering for precision analog supplies. The 2 A output comfortably powers clock-distribution and reference sections. Because the device integrates both MOSFETs, the switching node is internally defined, reducing layout sensitivity in dense mixed-signal boards. Designers typically follow it with a ferrite bead or small LDO when feeding sub-uV-noise references, but for most measurement subsystem rails the TPS54218 output, with 22 uF of output capacitance, meets ripple budgets directly.
Inirekomenda
Battery-Powered Portable Equipment
Portable and handheld instruments powered by single-cell Li-ion packs near end-of-discharge (approximately 3 V) or USB 5 V sources fall squarely within the 2.95 V to 6 V input window of the TPS54218ARTER. High synchronous-conversion efficiency extends battery runtime, and the 2 A capability supports radios, displays, and processors simultaneously. Programmable switching frequency up to 2 MHz keeps magnetics small, preserving the compact PCB area demanded by portable enclosures. Current-mode control maintains stability across the wide battery voltage excursion, and the SS/TR soft-start pin allows controlled inrush when the pack is hot-swapped. Designers should verify quiescent and shutdown currents against battery budgets in the TI datasheet, and place the converter away from sensitive receivers to control radiated EMI within the small conductive enclosure.
Inirekomenda
Security and Camera Systems
IP cameras and security electronics regulate 5 V PoE-derived or adapter power into core, DSP, and sensor rails. The TPS54218ARTER handles the 2 A class rails typical of image-sensor and compression-processor supplies. Its efficiency and thermal performance suit sealed outdoor enclosures where airflow is absent - the exposed-pad VQFN-16 conducts heat into the PCB ground plane effectively. Fixed-frequency operation permits filtering of switching artifacts that could couple into analog video or low-light sensor readout chains. The converter's fast transient response handles the bursty load profile of image compression engines, where current steps of an ampere can occur frame-to-frame. Compact footprint allows integration on small camera module carrier boards, and the adjustable output covers the varied 1.2 V to 3.3 V rails of modern sensor and SoC chipsets.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for TPS54218ARTER — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | TPS54218RTER | TPS54218RTE | TPS54418ARTER | TPS54418RTER |
|---|---|---|---|---|---|
| Package | VQFN-16 (RTE) 3x3 mm exposed pad | VQFN-16 (RTE) 3x3 mm - same | VQFN-16 (RTE) 3x3 mm - same | VQFN-16 (RTE) 3x3 mm - same | VQFN-16 (RTE) 3x3 mm - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Control Topology | Peak Current Mode (DF-CAP compatible) | Peak Current Mode - same | Peak Current Mode - same | Current Mode (SWIFT) | Current Mode (SWIFT) |
| Sourcing Channel | Rochester Electronics / LCSC / Wolfchip | Standard TI production channels | Standard TI production channels (tray) | Standard TI production channels | Standard TI production channels |
| Lifecycle Status | Active (extended-availability channel) | Active | Active | Active | Active |
Pangunahing mga Pagkakaiba
- Extended-availability sourcing channel (kumpara saTPS54218RTER)
- Up to 2 MHz switching for minimal magnetics (kumpara saTPS54418RTER)
- Trade-off: lower input voltage ceiling (kumpara saTPS54418ARTER)
Talaan ng Disenyo
Minimize the hot loop: place the input ceramic capacitor (10 uF, X5R/X7R) as close as possible to the VIN and GND pins, keeping the loop from VIN capacitor through the internal high-side FET, PH node, and low-side FET to ground as short and wide as possible. Connect the exposed pad directly to a solid ground plane with an array of 4-6 vias directly under the pad; this is both the primary thermal path and the return for gate-drive currents. Keep the PH switching-node copper area small but wide enough for 2 A, and route the VSENSE feedback trace away from PH and BOOT to avoid injecting switching noise into the feedback loop.
Estimated: at 5 V input, 1.8 V output, and 2 A load, output power is 3.6 W; at approximately 90% efficiency the device dissipates roughly 0.4 W. With a typical theta_JA near 40-50 C/W for a VQFN-16 3x3 mm on 1 square inch of 2-oz copper, junction rise is about 16-20 C above ambient - comfortable at 70 C ambient. Verify the exact theta_JA from the datasheet thermal table for your specific stack-up; these figures are estimates and the datasheet values govern final design.
Do not exceed the 6 V absolute input limit - a 5 V rail with transient overshoot on long inductive harnesses can breach it; add local TVS or bulk decoupling. Set the RT resistor to give design margin below 2 MHz, since tolerance shifts can push operation to the limit. The SS/TR soft-start pin must be configured for controlled startup into heavy capacitive loads, otherwise inrush can trigger current limit. Ensure the compensation network matches the datasheet recommendation for your output capacitor ESR to avoid double-pole instability with low-ESR ceramics.
Impormasyon ng Pagsunod sa Kautusan
RoHS compliance indicated in distributor listings (LCSC C2926926). REACH, halogen-free, and conflict-minerals status not stated in provided data - consult TI product page for official certificates.
