TS971IDT - 12 MHz Rail-to-Rail Low-Noise Op Amp, SOIC-8 | STMicroelectronics
MPN: TS971IDT ✓ NakahandaTS971IDT Ulas
An operational amplifier, commonly shortened to op amp, is an analog differential-input amplifier whose closed-loop behavior is set by external feedback components. Within the electronic component hierarchy an op amp sits in the analog amplifier class, alongside instrumentation and buffer amplifiers, all of which fall under the broader category of amplifier integrated circuits used for conditioning, scaling and buffering low-level signals. The TS971IDT occupies the high-speed end of that spectrum, offering enough bandwidth for video, filter and fast sensor interfaces rather than the slow precision of micropower parts.
Key characteristics of this device include a single amplifier per package, rail-to-rail output operation, and a very low-noise architecture. Because the output stage swings to the positive and negative supply rails, the amplifier can drive downstream circuitry without leaving a headroom-limited region, which matters in single 3.3 V or 5 V systems where the usable signal range is already narrow. The 12 MHz gain-bandwidth product pairs with the 4 V/us slew rate so that full-scale swings are reproduced without the soft edges typical of low-bandwidth amplifiers.
The TS97x family is offered in several packages to suit different board constraints. As noted in the manufacturer documentation, space-critical designs can use the SOT23-5 (2.8 x 2.9 mm) or DFN8 (3 x 3 mm) versions of the TS97x devices, while the TS971IDT itself ships in the industry-standard 8-pin SOIC outline that most assembly houses and prototype boards already support. Supply options run from 2.7 V to 10 V in total, or from 1.35 V to 5 V for single-supply operation.
Typical uses include sensor signal conditioning in industrial and IoT equipment, active filtering and audio path amplification, and general-purpose buffering ahead of analog-to-digital converters. In these roles the rail-to-rail output recovers maximum signal swing from a low supply, while the wide bandwidth preserves fast transients rather than rounding them off.
When laying out a design around the TS971IDT, place the bypass capacitors close to the supply pins and keep the feedback network short, since long traces add parasitic capacitance that can affect stability in high-gain configurations. Confirm that the required output swing, load current and supply noise budget match the application before fixing the gain structure in place.
This page consolidates manufacturer documentation, distributor availability information, drop-in alternatives drawn from the TS9xx family, and practical design guidance that a single distributor listing does not provide on its own, giving engineers the context needed to select and land the part correctly.
Mga alternatibo na pwedeng ilagay na TS971IDT — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok TS971IDT (parehas na form factor at footprint) — pagkakaiba sa Package, Gain-Bandwidth Product, Amplifier Type, Supply Voltage Range, Slew Rate.
TS951IDT
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →TS932IDT
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →TS934IDT
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →TS942AID
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →TS921IPT
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →TS971IDT Mga Pinakamataas na Rating at Electrical Characteristics
| Device Type | Operational Amplifier, Single, Rail-to-Rail Output |
| Number of Amplifiers per Package | 1 |
| Gain-Bandwidth Product | 12 MHz |
| Slew Rate | 4 V/us |
| Supply Voltage Range (Total) | 2.7 V to 10 V |
| Single-Supply Operation | 1.35 V to 5 V |
| Dual-Supply Operation | 2.7 V to 10 V |
| Type ng Output | Rail-to-Rail |
| Noise Class | Very low noise |
| Packhaging | SOIC-8 (SO-8), 8 pins |
| Uri ng Pagpapasok | Surface Mount |
| Classification | Standard (General Purpose) Amplifier |
| Datasheet Page Count | 17 pages |
Gabay sa Pin Configuration ng TS971IDT soic-8 (so-8), 8 pins
Pin configuration para sa TS971IDT (soic-8 (so-8), 8 pins package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa TS971IDT.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
TS971IDT ay nararapat para sa 6 aplikasyons: Sensor Signal Conditioning in IoT Devices, Audio Signal Path Amplification, Active Filter and Equalization Stages, ADC and DAC Signal Front-End, Portable and Battery-Powered Instrumentation, Video and Fast Transient Buffering.
Sensor Signal Conditioning in IoT Devices
The TS971IDT suits front-end conditioning for resistive, capacitive and piezoelectric sensors in IoT and industrial sensing modules. Its rail-to-rail output allows the conditioned signal to use nearly the full 2.7 V to 10 V supply span, which matters when the sensor output swings close to the rails. The 12 MHz gain-bandwidth product and 4 V/us slew rate keep fast sensor transients intact instead of rounding them off, so a bridge or capacitive-front-end output can be amplified without visible distortion. With one amplifier per 8-pin SOIC package, several conditioning channels fit on a dense board, and the small footprint makes it practical to place each stage close to its sensor connector.
Inirekomenda
Audio Signal Path Amplification
The TS971IDT is a natural fit for audio path stages that must preserve small signal detail while delivering a usable output level to a driver stage. Its very low noise architecture keeps the added noise floor below the program material, while the rail-to-rail output maximizes swing on 5 V single-supply analog rails common in portable audio hardware. The 12 MHz gain-bandwidth product is far beyond the 20 kHz audio band, so the amplifier introduces no audible roll-off and leaves headroom for headphone or line driver stages. In a 3.3 V mixed-signal board, the device can also serve as the buffer between a converter output and the analog output section.
Inirekomenda
Active Filter and Equalization Stages
Active filter and equalizer stages benefit directly from the 12 MHz gain-bandwidth product of the TS971IDT, which provides the loop gain needed for high-Q sections without gain peaking. The 4 V/us slew rate keeps large-signal content clean through cutoff transitions, avoiding the intermodulation products that appear when a slow amplifier is pushed into slew limiting. Rail-to-rail output operation lets a section work near the supply rails, which shortens the required passive component values and simplifies the design of filters that must pass low-frequency signals. The 8-pin SOIC-8 package also allows cascaded sections to be placed close together on analog boards where trace lengths and stray coupling matter.
Inirekomenda
ADC and DAC Signal Front-End
Placed between a converter and the rest of the analog chain, the TS971IDT provides the low-noise gain and the drive capability that converters rarely supply themselves. Because its output is rail-to-rail, the buffer can swing to the converter's full-scale range even on a 3.3 V supply, so no signal range is lost in the interface. The wide gain-bandwidth product means the buffer does not round off fast full-scale transitions produced by a rapidly updating converter, which would otherwise create code-dependent distortion. One amplifier per 8-pin SOIC package makes it straightforward to add gain or level shifting ahead of each converter channel without redesigning the board.
Inirekomenda
Portable and Battery-Powered Instrumentation
In portable test and measurement instruments, the TS971IDT allows measurement and signal-generation circuitry to run from a single low-voltage rail while still covering a wide bandwidth. The 2.7 V to 10 V supply range and 1.35 V to 5 V single-supply capability let the same device serve a 3.3 V handheld instrument and a 5 V bench-top block. Its rail-to-rail output recovers usable span that a fixed-threshold amplifier would waste, which directly improves measurement resolution on small signals. The very low noise specification keeps the amplifier from dominating the error budget of the instrument, and the 8-pin SOIC-8 package suits the compact, densely populated layouts typical of portable instruments.
Inirekomenda
Video and Fast Transient Buffering
Although the TS971IDT is a general-purpose amplifier, its 12 MHz gain-bandwidth product and 4 V/us slew rate make it suitable for fast transient buffering in video and control subcircuits. Video sync and control signals need clean edges and faithful amplitude reproduction, and slew limiting in a slow amplifier would round those edges and distort the timing relationship to the reference. Rail-to-rail output ensures the buffered signal retains full swing even when the system operates on a single 3.3 V rail. Use it as a buffer or unity-gain stage ahead of a driver, and keep the feedback loop compact so that the high bandwidth does not translate into unwanted ringing.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for TS971IDT — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | TS951IDT | TS932IDT | TS934IDT | TS942AID | TS921IPT |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | SOIC-8 | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same |
| Number of Amplifiers | 1 | 1 | 1 | 1 | 1 | 1 |
| Supply Voltage Range | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V |
| Output Type | Rail-to-Rail | Rail-to-Rail | Rail-to-Rail | Rail-to-Rail | Rail-to-Rail | Rail-to-Rail |
| Alternate Package Options in Family | SOIC-8 (TS97x also offered in SOT23-5 2.8 x 2.9 mm and DFN8 3 x 3 mm) | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
Pangunahing mga Pagkakaiba
- Highest speed option in the TS9xx single amplifier family (kumpara saTS951IDT)
- Rail-to-rail output on a low 2.7 V minimum supply (kumpara saTS921IPT)
- Very low noise architecture at 12 MHz bandwidth (kumpara saTS934IDT)
Talaan ng Disenyo
Place a 100 nF ceramic bypass capacitor directly between the supply pins and the ground plane, with the ground side terminated to the shortest path available, and add a 1 uF to 10 uF bulk capacitor on the same rail near the source. Keep the traces to the feedback resistors short and direct, and avoid routing the feedback net beneath the device where a second layer ground or signal plane can add unintended capacitance. In a multi-amplifier analog board, group the TS971IDT stages away from switching supplies and keep the analog ground return path separate from digital return currents.
Because the TS971IDT offers 12 MHz of gain-bandwidth product, the noise gain of the surrounding feedback network determines the actual usable bandwidth and the stability margin. With a single-pole feedback network, a capacitive load at the output can add a second pole and cause peaking or oscillation near unity-gain crossover, so add an isolation resistor of roughly 50 to 100 ohm when driving long PCB traces, capacitive cables or ADC sample-and-hold inputs. Keep the non-inverting input node physically small and route it away from the output node to avoid parasitic feedback through board coupling.
A common mistake is assuming the rail-to-rail output allows the output to sit exactly at the supply rail. Real saturation occurs slightly inside the rails, so design the output swing budget with margin, particularly at high output frequencies where the 4 V/us slew rate defines the achievable swing. A second pitfall is mixing supply rails: the device is specified from 2.7 V to 10 V total, so a 12 V supply is outside the rating. Third, do not substitute a slower TS9xx member into a wideband path without re-checking bandwidth, slew rate and stability.
Estimated: at a 5 V single supply with a 4 V peak-to-peak output into a 10 kOhm load, the output stage dissipates on the order of 0.4 mW, so supply-current draw is dominated by quiescent consumption and by the feedback network rather than by the load. Check the quiescent current figure in the manufacturer datasheet against your total power budget in battery-operated designs, since the TS921IPT low-power member of the family exists precisely for that tradeoff. Confirm that the source rail can start cleanly into the capacitive input filter network, and add a soft-start or supply ramp control upstream if the downstream device requires it.
Impormasyon ng Pagsunod sa Kautusan
No compliance statements were published alongside the part listings; confirm RoHS, REACH and lead-free status from the manufacturer product page or the declarations section of the official datasheet.