TS971IDT - 12 MHz Rail-to-Rail Low-Noise Op Amp, SOIC-8 | STMicroelectronics
MPN: TS971IDT ✓ 啟用中TS971IDT 概覽
An operational amplifier, commonly shortened to op amp, is an analog differential-input amplifier whose closed-loop behavior is set by external feedback components. Within the electronic component hierarchy an op amp sits in the analog amplifier class, alongside instrumentation and buffer amplifiers, all of which fall under the broader category of amplifier integrated circuits used for conditioning, scaling and buffering low-level signals. The TS971IDT occupies the high-speed end of that spectrum, offering enough bandwidth for video, filter and fast sensor interfaces rather than the slow precision of micropower parts.
Key characteristics of this device include a single amplifier per package, rail-to-rail output operation, and a very low-noise architecture. Because the output stage swings to the positive and negative supply rails, the amplifier can drive downstream circuitry without leaving a headroom-limited region, which matters in single 3.3 V or 5 V systems where the usable signal range is already narrow. The 12 MHz gain-bandwidth product pairs with the 4 V/us slew rate so that full-scale swings are reproduced without the soft edges typical of low-bandwidth amplifiers.
The TS97x family is offered in several packages to suit different board constraints. As noted in the manufacturer documentation, space-critical designs can use the SOT23-5 (2.8 x 2.9 mm) or DFN8 (3 x 3 mm) versions of the TS97x devices, while the TS971IDT itself ships in the industry-standard 8-pin SOIC outline that most assembly houses and prototype boards already support. Supply options run from 2.7 V to 10 V in total, or from 1.35 V to 5 V for single-supply operation.
Typical uses include sensor signal conditioning in industrial and IoT equipment, active filtering and audio path amplification, and general-purpose buffering ahead of analog-to-digital converters. In these roles the rail-to-rail output recovers maximum signal swing from a low supply, while the wide bandwidth preserves fast transients rather than rounding them off.
When laying out a design around the TS971IDT, place the bypass capacitors close to the supply pins and keep the feedback network short, since long traces add parasitic capacitance that can affect stability in high-gain configurations. Confirm that the required output swing, load current and supply noise budget match the application before fixing the gain structure in place.
This page consolidates manufacturer documentation, distributor availability information, drop-in alternatives drawn from the TS9xx family, and practical design guidance that a single distributor listing does not provide on its own, giving engineers the context needed to select and land the part correctly.
直接替換替代品,適用於 TS971IDT — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TS971IDT (相同外形與佔位) — 差異在於 Package, Gain-Bandwidth Product, Amplifier Type, Supply Voltage Range, Slew Rate.
TS951IDT
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →TS932IDT
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →TS934IDT
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →TS971IDT 最大額定值與電氣特性
| Device Type | Operational Amplifier, Single, Rail-to-Rail Output |
| Number of Amplifiers per Package | 1 |
| Gain-Bandwidth Product | 12 MHz |
| Slew Rate | 4 V/us |
| Supply Voltage Range (Total) | 2.7 V to 10 V |
| Single-Supply Operation | 1.35 V to 5 V |
| Dual-Supply Operation | 2.7 V to 10 V |
| 輸出類型 | Rail-to-Rail |
| Noise Class | Very low noise |
| 封裝 | SOIC-8 (SO-8), 8 pins |
| 安裝類型 | Surface Mount |
| Classification | Standard (General Purpose) Amplifier |
| Datasheet Page Count | 17 pages |
TS971IDT soic-8 (so-8), 8 pins 腳位配置指南
TS971IDT(soic-8 (so-8), 8 pins 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TS971IDT.
請參閱 資料表 以查看完整腳位配置。
典型應用
TS971IDT 適用於 6 應用s: Sensor Signal Conditioning in IoT Devices, Audio Signal Path Amplification, Active Filter and Equalization Stages, ADC and DAC Signal Front-End, Portable and Battery-Powered Instrumentation, Video and Fast Transient Buffering.
Sensor Signal Conditioning in IoT Devices
The TS971IDT suits front-end conditioning for resistive, capacitive and piezoelectric sensors in IoT and industrial sensing modules. Its rail-to-rail output allows the conditioned signal to use nearly the full 2.7 V to 10 V supply span, which matters when the sensor output swings close to the rails. The 12 MHz gain-bandwidth product and 4 V/us slew rate keep fast sensor transients intact instead of rounding them off, so a bridge or capacitive-front-end output can be amplified without visible distortion. With one amplifier per 8-pin SOIC package, several conditioning channels fit on a dense board, and the small footprint makes it practical to place each stage close to its sensor connector.
推薦
Audio Signal Path Amplification
The TS971IDT is a natural fit for audio path stages that must preserve small signal detail while delivering a usable output level to a driver stage. Its very low noise architecture keeps the added noise floor below the program material, while the rail-to-rail output maximizes swing on 5 V single-supply analog rails common in portable audio hardware. The 12 MHz gain-bandwidth product is far beyond the 20 kHz audio band, so the amplifier introduces no audible roll-off and leaves headroom for headphone or line driver stages. In a 3.3 V mixed-signal board, the device can also serve as the buffer between a converter output and the analog output section.
推薦
Active Filter and Equalization Stages
Active filter and equalizer stages benefit directly from the 12 MHz gain-bandwidth product of the TS971IDT, which provides the loop gain needed for high-Q sections without gain peaking. The 4 V/us slew rate keeps large-signal content clean through cutoff transitions, avoiding the intermodulation products that appear when a slow amplifier is pushed into slew limiting. Rail-to-rail output operation lets a section work near the supply rails, which shortens the required passive component values and simplifies the design of filters that must pass low-frequency signals. The 8-pin SOIC-8 package also allows cascaded sections to be placed close together on analog boards where trace lengths and stray coupling matter.
推薦
ADC and DAC Signal Front-End
Placed between a converter and the rest of the analog chain, the TS971IDT provides the low-noise gain and the drive capability that converters rarely supply themselves. Because its output is rail-to-rail, the buffer can swing to the converter's full-scale range even on a 3.3 V supply, so no signal range is lost in the interface. The wide gain-bandwidth product means the buffer does not round off fast full-scale transitions produced by a rapidly updating converter, which would otherwise create code-dependent distortion. One amplifier per 8-pin SOIC package makes it straightforward to add gain or level shifting ahead of each converter channel without redesigning the board.
推薦
Portable and Battery-Powered Instrumentation
In portable test and measurement instruments, the TS971IDT allows measurement and signal-generation circuitry to run from a single low-voltage rail while still covering a wide bandwidth. The 2.7 V to 10 V supply range and 1.35 V to 5 V single-supply capability let the same device serve a 3.3 V handheld instrument and a 5 V bench-top block. Its rail-to-rail output recovers usable span that a fixed-threshold amplifier would waste, which directly improves measurement resolution on small signals. The very low noise specification keeps the amplifier from dominating the error budget of the instrument, and the 8-pin SOIC-8 package suits the compact, densely populated layouts typical of portable instruments.
推薦
Video and Fast Transient Buffering
Although the TS971IDT is a general-purpose amplifier, its 12 MHz gain-bandwidth product and 4 V/us slew rate make it suitable for fast transient buffering in video and control subcircuits. Video sync and control signals need clean edges and faithful amplitude reproduction, and slew limiting in a slow amplifier would round those edges and distort the timing relationship to the reference. Rail-to-rail output ensures the buffered signal retains full swing even when the system operates on a single 3.3 V rail. Use it as a buffer or unity-gain stage ahead of a driver, and keep the feedback loop compact so that the high bandwidth does not translate into unwanted ringing.
推薦
推薦產品摘要
工程參考資料,適用於 TS971IDT — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TS951IDT | TS932IDT | TS934IDT | TS942AID | TS921IPT |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | SOIC-8 | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same |
| Number of Amplifiers | 1 | 1 | 1 | 1 | 1 | 1 |
| Supply Voltage Range | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V |
| Output Type | Rail-to-Rail | Rail-to-Rail | Rail-to-Rail | Rail-to-Rail | Rail-to-Rail | Rail-to-Rail |
| Alternate Package Options in Family | SOIC-8 (TS97x also offered in SOT23-5 2.8 x 2.9 mm and DFN8 3 x 3 mm) | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
主要差異化特點
- Highest speed option in the TS9xx single amplifier family (對比TS951IDT)
- Rail-to-rail output on a low 2.7 V minimum supply (對比TS921IPT)
- Very low noise architecture at 12 MHz bandwidth (對比TS934IDT)
設計說明
Place a 100 nF ceramic bypass capacitor directly between the supply pins and the ground plane, with the ground side terminated to the shortest path available, and add a 1 uF to 10 uF bulk capacitor on the same rail near the source. Keep the traces to the feedback resistors short and direct, and avoid routing the feedback net beneath the device where a second layer ground or signal plane can add unintended capacitance. In a multi-amplifier analog board, group the TS971IDT stages away from switching supplies and keep the analog ground return path separate from digital return currents.
Because the TS971IDT offers 12 MHz of gain-bandwidth product, the noise gain of the surrounding feedback network determines the actual usable bandwidth and the stability margin. With a single-pole feedback network, a capacitive load at the output can add a second pole and cause peaking or oscillation near unity-gain crossover, so add an isolation resistor of roughly 50 to 100 ohm when driving long PCB traces, capacitive cables or ADC sample-and-hold inputs. Keep the non-inverting input node physically small and route it away from the output node to avoid parasitic feedback through board coupling.
A common mistake is assuming the rail-to-rail output allows the output to sit exactly at the supply rail. Real saturation occurs slightly inside the rails, so design the output swing budget with margin, particularly at high output frequencies where the 4 V/us slew rate defines the achievable swing. A second pitfall is mixing supply rails: the device is specified from 2.7 V to 10 V total, so a 12 V supply is outside the rating. Third, do not substitute a slower TS9xx member into a wideband path without re-checking bandwidth, slew rate and stability.
Estimated: at a 5 V single supply with a 4 V peak-to-peak output into a 10 kOhm load, the output stage dissipates on the order of 0.4 mW, so supply-current draw is dominated by quiescent consumption and by the feedback network rather than by the load. Check the quiescent current figure in the manufacturer datasheet against your total power budget in battery-operated designs, since the TS921IPT low-power member of the family exists precisely for that tradeoff. Confirm that the source rail can start cleanly into the capacitive input filter network, and add a soft-start or supply ramp control upstream if the downstream device requires it.
合規資訊
No compliance statements were published alongside the part listings; confirm RoHS, REACH and lead-free status from the manufacturer product page or the declarations section of the official datasheet.