TUSB8042RGCR - 4-Port 5 Gbps USB 3.1 Hub | Texas Instruments
MPN: TUSB8042RGCR ✓ NakahandaTUSB8042RGCR Ulas
A USB hub controller is an interface integrated circuit that manages one upstream USB connection and multiple downstream ports. Within the hierarchy of USB interface controllers, it adds device enumeration, port routing, power-management coordination, and traffic arbitration while allowing USB peripherals to share one host controller. The TUSB8042RGCR combines SuperSpeed and legacy USB support in one device, simplifying system design where both high-bandwidth storage and conventional peripherals must coexist.
The principal features include four downstream ports, SuperSpeed operation at 5.0 Gbps, and backward compatibility with Full Speed and High Speed USB devices. GPIO, I2C, and SMBus interfaces support configuration and supervisory functions. Per-port power switching and overcurrent detection improve fault isolation when a downstream device faults. The manufacturer specifies a commercial operating range of 0°C to 70°C for the TUSB8042RGCR ordering option.
Internally, the controller coordinates traffic between the upstream host-facing port and four downstream USB ports while maintaining independent command, data, and status paths needed for USB connectivity. This integrated hub architecture reduces the number of discrete USB interface and switching elements required in a design. The exposed-pad VQFN construction also supports thermal transfer into a multilayer PCB, an important consideration when several attached devices can drive continuous data activity.
Typical uses include external docking stations, laboratory data-acquisition equipment, industrial USB expansion, computer accessories, and embedded systems that need multiple USB connections. In each case, the five-gigabit SuperSpeed path is useful for storage, cameras, and other high-throughput peripherals, while legacy support allows existing USB 1.1 and USB 2.0 devices to operate without separate downstream controllers.
Design the board with the exposed pad connected to the ground plane and follow the manufacturer’s recommended decoupling and high-speed layout guidance. Place decoupling capacitance close to supply pins, provide a continuous reference plane beneath the high-speed region, and route differential pairs with matched geometry. Verify power-distribution capacity and overcurrent behavior for the intended downstream-load combination.
This page consolidates the manufacturer ordering information, package characteristics, verified source links, compatible same-package options, and practical PCB guidance for engineers evaluating the TUSB8042RGCR as a four-port USB hub controller.
Mga alternatibo na pwedeng ilagay na TUSB8042RGCR — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok TUSB8042RGCR (parehas na form factor at footprint) — pagkakaiba sa Maximum Data Rate, Number of Downstream Ports, Package, Product Type.
TUSB8042AIRGCR
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
TUSB8042RGCT
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →TUSB8042RGCR Mga Spesipikasyon
| Device Type | 4-Port SuperSpeed USB 3.1 Hub Controller |
| Number of USB Ports | 4 downstream ports |
| SuperSpeed Maximum Data Rate | 5.0 Gbps |
| USB Standards Compatibility | USB 3.1, USB 2.0, and USB 1.1 |
| Maximum SuperSpeed Data Rate | 5.0 Gbps |
| Packhaging | 64-pin VQFN (RGC), 9 x 9 mm |
| Bilang ng Pin | 64 pins |
| Hanay ng Temperature na Operasyon | 0°C to 70°C |
| Control Interfaces | GPIO, I2C, and SMBus |
| Downstream Port Power Management | Per-port power switching |
| Fault Protection | Per-port overcurrent detection |
| Uri ng Pagpapasok | Surface Mount |
| Package Thermal Pad | Exposed pad |
Gabay sa Pin Configuration ng TUSB8042RGCR exposed pad
Pin configuration para sa TUSB8042RGCR (exposed pad package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa TUSB8042RGCR.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
TUSB8042RGCR ay nararapat para sa 6 aplikasyons: Desktop USB-C Docking Station, Industrial USB Data Acquisition, Test and Measurement Equipment, External Storage and Media Hub, Embedded USB Expansion Board, Security and Surveillance Peripherals.
Desktop USB-C Docking Station
The TUSB8042RGCR fits a desktop docking station that must expose several USB ports while preserving a 5.0 Gbps SuperSpeed path for storage or display-adjacent peripherals. Its four downstream ports can serve a mixture of high-speed and legacy devices because the controller supports USB 3.1, USB 2.0, and USB 1.1 connections. GPIO, I2C, and SMBus provide avenues for system monitoring and configuration. The important design trade-off is power: each downstream port can draw current, so the dock’s supply must be sized for the worst permitted combination and protected by the hub’s per-port switching and overcurrent-detection functions.
Inirekomenda
Industrial USB Data Acquisition
The TUSB8042RGCR can serve as the USB expansion controller in industrial acquisition equipment that connects several peripherals to one host port. The 5.0 Gbps SuperSpeed capability supports high-throughput data paths, while legacy compatibility permits existing USB 1.1 and USB 2.0 sensors or control devices to remain connected. Per-port overcurrent detection helps isolate a faulty cable or attached load, and power switching supports controlled downstream-port management. For installations operating below 0°C or above 70°C, select the industrial-temperature TUSB8042AI family variant and verify its complete pin and electrical compatibility.
Inirekomenda
Test and Measurement Equipment
The TUSB8042RGCR is appropriate for test and measurement systems that need multiple external USB connections without dedicating a host controller to every peripheral. A SuperSpeed port at up to 5.0 Gbps accommodates instrument data transfers, while USB 2.0 and USB 1.1 compatibility allows legacy mice, service interfaces, and adapters to remain attached. The controller’s I2C, SMBus, and GPIO interfaces can assist board-level configuration and supervisory control. Designers should maintain short high-speed routes, continuous reference planes, and adequate supply decoupling because simultaneous SuperSpeed traffic can increase board-level power and signal-integrity requirements.
Inirekomenda
External Storage and Media Hub
The TUSB8042RGCR can centralize external storage, card readers, and media devices in a powered hub enclosure. Its four SuperSpeed ports operate at up to 5.0 Gbps, reducing the bandwidth constraint associated with multi-device copying, backup, and media ingestion workflows. USB 2.0 and USB 1.1 compatibility lets users connect older accessories without separate controllers. The engineering priority is a power budget: the hub supply and copper paths must support the intended number of active ports, while per-port overcurrent detection limits the effect of an individual downstream fault. Keep the 5.0 Gbps differential routing away from noisy switching nodes.
Inirekomenda
Embedded USB Expansion Board
The TUSB8042RGCR is useful on an embedded expansion board that converts one host USB connection into four downstream ports for sensors, storage, cameras, or service interfaces. The mixed-speed compatibility reduces the need for separate USB 2 and USB 3 controllers, while the exposed-pad VQFN package requires careful thermal and layout planning. GPIO, I2C, and SMBus can share the system control bus or implement port-status monitoring. Because the TUSB8042RGCR is specified for 0°C to 70°C, an enclosure exposed to wider industrial temperatures requires an extended-temperature variant and a complete review of electrical, timing, and pin compatibility.
Inirekomenda
Security and Surveillance Peripherals
The TUSB8042RGCR can manage several cameras or other high-bandwidth security peripherals in an edge system with a single host-side USB connection. SuperSpeed operation at up to 5.0 Gbps provides useful headroom for video transfer, while legacy compatibility supports maintenance keyboards, configuration adapters, and lower-rate sensors. Per-port switching and overcurrent detection improve resilience when peripheral power faults occur. The hub does not replace independent security isolation or power conditioning, so system engineers should still provision appropriate protection and enforce separate physical and logical trust boundaries for sensitive equipment.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for TUSB8042RGCR — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | TUSB8042AIRGCR | TUSB8042RGCT |
|---|---|---|---|
| Package | 64-pin VQFN (RGC), 9 x 9 mm | 64-pin VQFN (RGC) | 64-pin VQFN (RGC) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | 4-Port SuperSpeed USB 3.1 Hub Controller | 4-Port SuperSpeed USB 3.1 Hub Controller | 4-Port SuperSpeed USB 3.1 Hub Controller |
| SuperSpeed Data Rate | 5.0 Gbps | 5.0 Gbps | 5.0 Gbps |
| Downstream Port Count | 4 ports | 4 ports | 4 ports |
| Operating Temperature Range | 0°C to 70°C | -40°C to 85°C | 0°C to 70°C |
| Legacy USB Compatibility | USB 2.0 and USB 1.1 | USB 2.0 and USB 1.1 | USB 2.0 and USB 1.1 |
| Control Interfaces | GPIO, I2C, and SMBus | GPIO, I2C, and SMBus | GPIO, I2C, and SMBus |
| Per-Port Power Switching | Supported | Supported | Supported |
| Per-Port Overcurrent Detection | Supported | Supported | Supported |
Pangunahing mga Pagkakaiba
- Four-port SuperSpeed expansion in one hub controller (kumpara saTUSB8042RGCT)
- Commercial-grade ordering option with mixed-speed USB support (kumpara saTUSB8042AIRGCR)
- Integrated downstream fault-management functions (kumpara saTUSB8042RGCT)
Talaan ng Disenyo
Use the manufacturer layout recommendations for the RGC package, connect the exposed pad to the ground plane, and place input and internal supply decoupling capacitors close to their associated pins. Maintain continuous reference planes beneath the SuperSpeed routes. Differential pair geometry should remain matched and should be kept free of stubs, test pads that lack a proper transition, and intervening plane splits.
Size the USB power-distribution network for the maximum intended combination of downstream loads rather than a single attached device. Verify supply droop, current-limit behavior, inrush, and per-port overcurrent thresholds across startup and fault conditions. The hub controller coordinates port power, but the board still needs appropriately rated switches, protection, copper, and a supply capable of supporting the selected load profile.
The exposed pad is a primary thermal path for this VQFN package. Use the manufacturer’s land pattern and thermal design guidance, provide uninterrupted ground copper beneath and around the pad, and avoid placing thermal breaks in high-current or high-speed regions. Validate the final enclosure and ambient-temperature assumptions during thermal testing, especially when several SuperSpeed peripherals operate concurrently.
Route SuperSpeed differential pairs as impedance-controlled, length-matched interconnects over a continuous reference plane. Keep connector and ESD-protection transitions short, and place any required AC coupling or protection devices according to the manufacturer’s reference layout. Avoid routing USB signals beside switching regulators, high-current inductors, crystal circuits, or other likely noise sources.
Do not select a replacement solely because the package drawing looks identical. Confirm exact electrical ratings, temperature grade, pin assignment, exposed-pad connection, firmware or configuration requirements, and production packing orientation. The TUSB8042RGCR is a commercial-temperature option, so an extended-temperature design requires a suitable industrial variant and a documented compatibility review.
Impormasyon ng Pagsunod sa Kautusan
The available manufacturer ordering information identifies the package and temperature range but does not state the requested compliance details. The TUSB8042RGCR is a commercial 0°C to 70°C ordering option; the related TUSB8042AI industrial option is specified from -40°C to 85°C.