G

WM8731CSEFL - Stereo Audio Codec with Headphone Driver | Cirrus Logic

MPN: WM8731CSEFL ✓ Nakahanda
2.7 V to 3.6 V Vdss 28-QFN, 5 mm x 5 mm Package
MOQ: 1 |

WM8731CSEFL Ulas

Cirrus Logic, Inc. WM8731CSEFL is a stereo audio codec with an integrated headphone driver, 24-bit serial audio interface, programmable sample-rate support, and a 28-QFN 5 mm by 5 mm package. The device is positioned for portable Internet audio equipment that requires one compact IC to perform digital-to-analog conversion, headphone amplification, and analog audio input handling.

An audio codec is an interface IC that converts digital audio samples into analog signals and accepts analog audio for conversion into a digital format. In the broader component hierarchy, the WM8731 belongs to the audio codec class, sits within interface ICs, and ultimately forms part of a signal-chain or audio-processing subsystem. Its integrated headphone driver reduces the need for separate analog output stages in space-constrained portable products.

The WM8731CSEFL is identified as a 24-bit codec with a serial interface and programmable sample rates. Those features support designs in which a host processor exchanges audio data over a serial bus while an application selects the required sample rate. The operating supply range listed for this device is 2.7 V to 3.6 V, which makes it appropriate for 3.3 V portable systems with a regulated analog or mixed-signal supply rail.

The 28-QFN package measures 5 mm by 5 mm and supports compact PCB placement. Because it integrates the codec and headphone-driver functions, board designers can reduce the number of discrete audio components while preserving a defined signal path from a digital audio source to headphones or another analog output. The manufacturer datasheet is the authoritative source for supported interfaces, control registers, clocking requirements, analog performance, and recommended application circuits.

Typical uses include portable Internet audio players, digital personal audio products, compact consumer audio equipment, and embedded systems with a headphone connector. The codec can sit beside a host processor or digital audio interface, with the host configuring the serial link and operating registers. System partitioning still depends on microphone topology, analog signal levels, connector impedance, and the desired headphone output power.

Careful layout is essential because mixed-signal devices combine high-speed digital interfaces with low-level analog inputs and outputs. Place decoupling capacitors close to the supply pins, route headphone outputs away from sensitive inputs, and follow the ground and layout recommendations in the manufacturer datasheet. Verify package dimensions, exposed-pad requirements, and pin assignments against the latest datasheet revision before fabrication.

This product page organizes the device identity, package information, operating voltage, sourcing questions, replacement limits, and application-oriented design guidance. Because audio designs are sensitive to clocking, grounding, and output loading, engineers should use the manufacturer application information together with board-level acoustic and thermal validation before releasing a production design.

Mga alternatibo na pwedeng ilagay na WM8731CSEFL — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok WM8731CSEFL (parehas na form factor at footprint) — pagkakaiba sa Package.

Cirrus Logic Inc.
Package: 28-QFN (5 x 5 mm)
Ikabit sa WM8731CSEFL →

WM8731CLSEFL

✅ Drop-In
Cirrus Logic Inc.
📦 28-QFN (5x5)
Stereo audio codec with headphone driver · 24-bit serial · 28-QFN (5 x 5 mm) · 28 pins · CMOS · ESD-sensitive device · 24-bit · 24-bit

Magkontak para sa presyo

Tingnan ang Datasheet →

WM8731CSEFL Mga Pinakamataas na Rating at Electrical Characteristics

Device Type Stereo audio codec with headphone driver
Audio Resolution 24 bit
Uri ng Interface Serial audio interface
Supply Voltage Range 2.7 V to 3.6 V
Packhaging 28-QFN, 5 mm x 5 mm
Uri ng Pagpapasok Surface mount
Headphone Output Channels 2 channels
Integrated Headphone Driver Yes

Gabay sa Pin Configuration ng WM8731CSEFL 28-qfn, 5 mm x 5 mm

Pin configuration para sa WM8731CSEFL (28-qfn, 5 mm x 5 mm package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.

Pinout diagram ng 28-qfn, 5 mm x 5 mm package para sa WM8731CSEFL

Wala ng detalyadong pinout data na magagamit para sa WM8731CSEFL.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

WM8731CSEFL ay nararapat para sa 6 aplikasyons: Portable Internet Audio Player, Digital Personal Audio Product, Embedded Voice and Music Player, Portable Connected Audio Accessory, Compact Audio Interface Module, Portable Audio Test and Demonstration Platform.

📱

Portable Internet Audio Player

The WM8731CSEFL fits a portable Internet audio player because it combines a 24-bit serial audio interface with an integrated stereo headphone driver. The host processor can send digital audio to the codec over the serial interface, while programmable sample-rate support allows the software stack to select an appropriate operating rate. With a 2.7 V-to-3.6 V supply requirement and a compact 28-QFN 5 mm by 5 mm package, the device supports a restrained board layout. The design must still provide clean analog and digital supplies, correct clocking, stable references, and the decoupling required by the manufacturer.

🎧

Digital Personal Audio Product

A digital personal audio product can use the WM8731CSEFL as the final audio-output stage between its digital audio processor and headphones. The integrated headphone driver avoids a separate conventional output-amplifier block, while the 24-bit serial interface provides a clearly defined connection to the host device. The 5 mm by 5 mm 28-QFN package preserves board area in wearable and compact consumer products. Engineers should verify headphone impedance, output power, channel separation, and thermal behavior, because those requirements determine whether an additional output stage is needed.

🔊

Embedded Voice and Music Player

The WM8731CSEFL suits embedded systems that play music, voice prompts, or mixed digital audio through a headphone connector. Its serial interface separates the audio transport from the host processor’s general-purpose bus, allowing the audio format and sample rate to be coordinated by firmware. Programmable sample-rate support is useful when the system changes between stored-content rates, although the supported rates must be confirmed in the manufacturer datasheet. The 2.7 V minimum supply also calls for a regulator when the embedded platform operates from a lower battery voltage.

🌐

Portable Connected Audio Accessory

In a connected portable audio accessory, the WM8731CSEFL can provide the local playback path from a digital audio source to a headset. A wireless or wired digital interface handles content transfer, while the codec handles analog conversion and headphone drive. Its 28-QFN footprint limits occupied board area, and the integrated driver simplifies analog routing. Designers should keep the codec clock and power domains isolated from noisy digital activity, provide local bypass capacitance, and verify connector ground continuity to prevent channel imbalance or unintended noise.

🧩

Compact Audio Interface Module

The WM8731CSEFL is suitable for a compact module that converts digital audio from a host board into a headphone-level analog output. Because the codec and headphone driver share one package, module designers can reduce connector-to-connector routing distance and avoid a discrete output stage. The interface remains suitable for experimentation and embedded audio platforms, but pin multiplexing, clock routing, and control firmware must match the device configuration documented by the manufacturer. A prototype should also confirm that the selected module’s supply rail remains inside the 2.7 V-to-3.6 V operating window.

🔧

Portable Audio Test and Demonstration Platform

A portable audio demonstration platform can pair the WM8731CSEFL with a digital signal source to exercise the complete playback path from serial samples through the codec and headphone driver. This arrangement is useful for evaluating firmware-controlled sample rates, output channels, and system-level audio behavior. Because the compact QFN package exposes a thermal pad and fine-pitch leads, the board should follow the manufacturer’s land-pattern and assembly guidance. Bring-up should begin with confirmed clocking and supply sequencing before evaluating analog noise, distortion, channel balance, or headphone stability.

What is the WM8731CSEFL?
The WM8731CSEFL is a Cirrus Logic stereo audio codec with an integrated headphone driver, a 24-bit serial audio interface, and programmable sample rates. According to the Cirrus Logic manufacturer datasheet, it is intended for portable Internet audio equipment. The device combines digital-to-analog audio conversion and headphone output capability in a 28-QFN package measuring 5 mm by 5 mm.
What is the supply voltage range of the WM8731CSEFL?
The WM8731CSEFL operates from 2.7 V to 3.6 V, according to the Cirrus Logic manufacturer datasheet and the published WM8731CSEFL technical comparison. This range suits 3.3 V portable equipment when a suitably regulated supply rail is available. Designers should verify the power-up sequence, decoupling requirements, and separate analog or headphone supply arrangements against the manufacturer application circuit.
Where can I download the WM8731CSEFL datasheet PDF?
The WM8731CSEFL datasheet is available through the linked datasheet record, while the official device information is published under the Wolfson Microelectronics and Cirrus Logic name. The manufacturer document covers the pinout, serial interface, control registers, electrical characteristics, clocking, and application circuits. Verify the document revision and ordering information before using it for production release.
Where can I find the WM8731CSEFL pinout and package drawing?
Use the pin-description table and package drawing in the Cirrus Logic manufacturer datasheet for the authoritative WM8731CSEFL pinout. The component is a 28-QFN package with dimensions of 5 mm by 5 mm. Check the exposed-pad connection, pin-1 orientation, land pattern, solder-mask geometry, and recommended reflow profile because these mechanical details must match the selected package drawing.
What are the key specifications of WM8731CSEFL that engineers should know?
The principal WM8731CSEFL specifications are a 24-bit serial audio interface, programmable sample-rate capability, an integrated stereo headphone driver, a 2.7 V to 3.6 V supply range, and a 28-QFN 5 mm by 5 mm package. According to the Cirrus Logic manufacturer datasheet, these characteristics suit portable Internet audio products. Clock topology, analog performance, and control functions must be checked in the datasheet.
Can the WM8731CSEFL be used in portable Internet audio products?
Yes, the WM8731CSEFL is specifically identified for portable Internet audio equipment. Its 24-bit serial interface and programmable sample rates support digital audio input, while the integrated headphone driver provides the analog output path. A practical implementation still requires correct master-clock generation, suitable analog supply design, controlled headphone impedance, and PCB layout that separates sensitive analog paths from digital signals.
What is the difference between WM8731CSEFL and WM8731CLSEFL?
The principal documented difference is the minimum supply voltage: WM8731CSEFL starts at 2.7 V, while WM8731CLSEFL is specified from 1.8 V. Both extend to 3.6 V. This 0.9 V minimum-supply difference must be considered in replacement decisions because a 1.8 V-capable system may operate outside the WM8731CSEFL supply range. Confirm the complete pin and clock configuration in each datasheet.
Is WM8731CSEFL suitable for a 1.8 V portable design?
The WM8731CSEFL should not be selected directly for a rail below its documented 2.7 V minimum without an appropriate regulator and a complete review of every supply domain. The WM8731CLSEFL comparison identifies a 1.8 V minimum for that related variant. Alternatively, use a 2.7 V-to-3.6 V regulator for the WM8731CSEFL and verify startup, headroom, noise, and current demand across the battery range.
When should I choose the WM8731CSEFL instead of another audio codec?
Choose the WM8731CSEFL when the design needs a compact 24-bit stereo codec with an integrated headphone driver, a 2.7 V-to-3.6 V supply rail, and programmable serial-audio operation in a 28-QFN footprint. Consider another codec when the host interface, minimum voltage, analog performance, microphone topology, package, or qualification requirements differ. The manufacturer pin and electrical tables determine whether another device is a genuine replacement.
What is the best drop-in replacement for the WM8731CSEFL?
No alternative is confirmed here as a universally safe drop-in replacement because replacement claims require identical package geometry, pin functions, clocking, supply domains, and acceptable electrical performance. The WM8731CLSEFL is a closely related family device, but its 1.8 V minimum differs from the 2.7 V minimum of the WM8731CSEFL. Use the Request a Quote form for sourcing help and verify any proposed substitute against both manufacturer datasheets.
What can replace the WM8731CSEFL?
The WM8731CLSEFL is a related replacement candidate with the same core audio-codec architecture, while WM8731CSEFL/R represents a tape-and-reel packaging designation rather than a distinct engineering alternative. Neither candidate should be installed without checking the complete pinout, supply requirements, interface timing, and package drawing. No cross-brand device has been established as a true drop-in replacement.
Is there a Cirrus Logic equivalent for the WM8731CSEFL?
The closest Cirrus Logic family candidate identified for the WM8731CSEFL is WM8731CLSEFL, which supports operation from 1.8 V to 3.6 V rather than 2.7 V to 3.6 V. That difference makes it potentially useful in lower-voltage portable designs but does not establish unconditional replacement. Confirm pin compatibility and the required supply topology in the manufacturer datasheet before redesigning the PCB.
How should the WM8731CSEFL PCB layout be designed?
Place the required input, output, and bypass capacitors close to their associated pins, maintain the manufacturer-recommended ground arrangement, and keep headphone-output routing away from sensitive microphone or line-input nodes. The 28-QFN 5 mm by 5 mm footprint also requires attention to the exposed pad and its thermal and electrical connection. Use the Cirrus Logic manufacturer layout guidance as the basis for the final land pattern.
Does the WM8731CSEFL require external headphone amplification?
The WM8731CSEFL includes a headphone driver, so it can provide the final analog headphone-output stage without a conventional external output amplifier when operated within the manufacturer’s stated voltage, current, load, and impedance limits. Applications needing greater power, bridge-tied outputs, or unusual loads may still require additional circuitry. Confirm output power, distortion, and stability in the electrical characteristics.
Where can I buy the WM8731CSEFL and what is its lead time?
Use the Request a Quote form on this page to request current WM8731CSEFL availability, lead time, minimum order quantity, and orderable packaging. Current inventory and delivery schedules can change, so engineers should obtain a written quotation before committing the manufacturing schedule. The Request a Quote workflow also helps confirm the exact CSEFL ordering code rather than a tape-and-reel suffix variant.
Is the WM8731CSEFL in stock?
Current stock for WM8731CSEFL should be confirmed through the Request a Quote form on this page. The component is offered by authorized distribution channels, but price breaks and available quantities can vary by date, region, and packaging. Share the required quantity, target date, and acceptable shipment destination with the quote request so the response reflects the actual order requirement.
How is the WM8731CSEFL different from a generic audio interface IC?
The WM8731CSEFL combines a 24-bit stereo audio codec, a serial digital audio interface, programmable sample-rate operation, and an integrated headphone driver in one 28-QFN device. A generic interface IC may only provide digital conversion, clocking, or bus signaling and might require separate analog output amplification. The WM8731 is therefore more tightly aligned with portable Internet audio products and complete analog headphone-output paths.

Impormasyon ng Talumpati sa Engineering for WM8731CSEFL — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the WM8731CSEFL for a portable Internet audio or compact consumer-audio design that operates from a regulated 2.7 V-to-3.6 V rail and needs a 24-bit serial codec with an integrated headphone driver in a 28-QFN footprint. It is the straightforward choice when the existing system already uses a 3.3 V supply and does not require operation below 2.7 V. Consider the WM8731CLSEFL when a lower-voltage architecture is important, but verify the complete pin, clock, register, and electrical compatibility because its minimum supply voltage is 1.8 V. Do not select CS3310, CS4360, or other audio-codec candidates as drop-in replacements without proving package, pin, interface, clocking, and performance equivalence. For a production release, use the manufacturer datasheet and application circuit, then validate headphone loads, analog performance, supply startup, and thermal behavior on representative hardware.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto WM8731CLSEFL
Package 28-QFN (5x5) 28-QFN (5x5)
Brand Cirrus Logic, Inc. Cirrus Logic, Inc.
Minimum Supply Voltage 2.7 V 1.8 V
Maximum Supply Voltage 3.6 V 3.6 V
Primary Application Portable Internet audio Portable Internet audio
Product Class Stereo codec with headphone driver Stereo codec with headphone driver

Pangunahing mga Pagkakaiba

  • Lower-voltage family option for portable power designs (kumpara saWM8731CLSEFL)
  • Compact mixed-signal integration (kumpara saWM8731CLSEFL)
  • Direct fit for 3.3 V portable systems (kumpara saWM8731CLSEFL)

Talaan ng Disenyo

Design the WM8731CSEFL supply around its documented 2.7 V to 3.6 V operating range. Use separate local bypass paths for the supply pins specified by the manufacturer, place the capacitors close to the device, and verify startup behavior across the full input-voltage range. The exposed pad should follow the datasheet’s thermal and electrical recommendations. Estimated power calculations require the actual supply voltage, current, and output-load operating point and should be treated as design estimates until confirmed on the assembled board.

Separate the headphone-output and analog-input routing from digital clocks and control signals. Keep the codec clock source and traces away from high-impedance audio inputs, maintain a continuous ground reference for the audio path, and place bypass and routing components close to their relevant pins. Use the manufacturer pinout and reference layout to confirm pin-1 orientation, exposed-pad treatment, and the exact 28-QFN land pattern before fabrication.

Do not treat the WM8731CLSEFL as an unconditional substitute for the WM8731CSEFL: its documented minimum supply voltage is 1.8 V rather than 2.7 V, a 0.9 V difference. Confirm that all supply domains, clock ratios, serial formats, control-register defaults, and pin functions are acceptable for the target PCB. The WM8731CSEFL/R suffix denotes an alternate reel or packing designation and should not be treated as a separate functional replacement.

Validate the serial audio clock, data, and control traces as a complete interface rather than routing them independently. Check edge-rate requirements, trace loading, return paths, and grounding against the manufacturer’s timing and layout guidance. For analog performance, evaluate output noise, distortion, channel balance, and headphone stability with the intended cable and load. The manufacturer electrical characteristics define the test conditions needed for meaningful comparisons.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The exact WM8731CSEFL compliance declarations require confirmation in the manufacturer product documentation or current declaration of compliance.

Data napatotohanan sa: 2026-11-10 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

WM8731CSEFL datasheet WM8731CSEFL pinout WM8731CSEFL datasheet pdf WM8731CSEFL equivalent WM8731CSEFL replacement WM8731CSEFL vs WM8731CLSEFL WM8731CSEFL footprint WM8731CSEFL application circuit WM8731CSEFL price WM8731CSEFL stock Cirrus Logic WM8731CSEFL WM8731CSEFL 28-QFN pinout WM8731CSEFL 2.7V 3.6V codec WM8731CSEFL headphone driver how to replace WM8731CSEFL

Mga kaugnay na Mga Komponente at mga Tuntunin

Cirrus Logic, Inc. Wolfson Microelectronics WM8731CSEFL WM8731CLSEFL audio codec stereo audio codec headphone driver audio interface IC mixed-signal semiconductor 24-bit audio serial audio interface programmable sample rate portable Internet audio 28-QFN package QFN family surface-mount package 2.7 V minimum supply 3.6 V maximum supply digital-to-analog converter headphone output analog input RoHS REACH MSL Level
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ