WM8731CSEFL - Stereo Audio Codec with Headphone Driver | Cirrus Logic
料号: WM8731CSEFL ✓ 量产中WM8731CSEFL 概述
An audio codec is an interface IC that converts digital audio samples into analog signals and accepts analog audio for conversion into a digital format. In the broader component hierarchy, the WM8731 belongs to the audio codec class, sits within interface ICs, and ultimately forms part of a signal-chain or audio-processing subsystem. Its integrated headphone driver reduces the need for separate analog output stages in space-constrained portable products.
The WM8731CSEFL is identified as a 24-bit codec with a serial interface and programmable sample rates. Those features support designs in which a host processor exchanges audio data over a serial bus while an application selects the required sample rate. The operating supply range listed for this device is 2.7 V to 3.6 V, which makes it appropriate for 3.3 V portable systems with a regulated analog or mixed-signal supply rail.
The 28-QFN package measures 5 mm by 5 mm and supports compact PCB placement. Because it integrates the codec and headphone-driver functions, board designers can reduce the number of discrete audio components while preserving a defined signal path from a digital audio source to headphones or another analog output. The manufacturer datasheet is the authoritative source for supported interfaces, control registers, clocking requirements, analog performance, and recommended application circuits.
Typical uses include portable Internet audio players, digital personal audio products, compact consumer audio equipment, and embedded systems with a headphone connector. The codec can sit beside a host processor or digital audio interface, with the host configuring the serial link and operating registers. System partitioning still depends on microphone topology, analog signal levels, connector impedance, and the desired headphone output power.
Careful layout is essential because mixed-signal devices combine high-speed digital interfaces with low-level analog inputs and outputs. Place decoupling capacitors close to the supply pins, route headphone outputs away from sensitive inputs, and follow the ground and layout recommendations in the manufacturer datasheet. Verify package dimensions, exposed-pad requirements, and pin assignments against the latest datasheet revision before fabrication.
This product page organizes the device identity, package information, operating voltage, sourcing questions, replacement limits, and application-oriented design guidance. Because audio designs are sensitive to clocking, grounding, and output loading, engineers should use the manufacturer application information together with board-level acoustic and thermal validation before releasing a production design.
直接替换替代料: WM8731CSEFL ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: WM8731CSEFL (相同外形与封装尺寸) ——差异在于 Package.
WM8731CLSEFL
✅ 直接替换联系询价
查看数据手册 →WM8731CSEFL 最大额定值与电气特性
| Device Type | Stereo audio codec with headphone driver |
| Audio Resolution | 24 bit |
| 接口类型 | Serial audio interface |
| Supply Voltage Range | 2.7 V to 3.6 V |
| 封装 | 28-QFN, 5 mm x 5 mm |
| 安装类型 | Surface mount |
| Headphone Output Channels | 2 channels |
| Integrated Headphone Driver | Yes |
WM8731CSEFL 28-qfn, 5 mm x 5 mm 引脚配置指南
WM8731CSEFL(28-qfn, 5 mm x 5 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: WM8731CSEFL.
请参阅 数据手册 以查看完整引脚配置。
典型应用
WM8731CSEFL 适用于 6 应用s: Portable Internet Audio Player, Digital Personal Audio Product, Embedded Voice and Music Player, Portable Connected Audio Accessory, Compact Audio Interface Module, Portable Audio Test and Demonstration Platform.
Portable Internet Audio Player
The WM8731CSEFL fits a portable Internet audio player because it combines a 24-bit serial audio interface with an integrated stereo headphone driver. The host processor can send digital audio to the codec over the serial interface, while programmable sample-rate support allows the software stack to select an appropriate operating rate. With a 2.7 V-to-3.6 V supply requirement and a compact 28-QFN 5 mm by 5 mm package, the device supports a restrained board layout. The design must still provide clean analog and digital supplies, correct clocking, stable references, and the decoupling required by the manufacturer.
推荐
Digital Personal Audio Product
A digital personal audio product can use the WM8731CSEFL as the final audio-output stage between its digital audio processor and headphones. The integrated headphone driver avoids a separate conventional output-amplifier block, while the 24-bit serial interface provides a clearly defined connection to the host device. The 5 mm by 5 mm 28-QFN package preserves board area in wearable and compact consumer products. Engineers should verify headphone impedance, output power, channel separation, and thermal behavior, because those requirements determine whether an additional output stage is needed.
推荐
Embedded Voice and Music Player
The WM8731CSEFL suits embedded systems that play music, voice prompts, or mixed digital audio through a headphone connector. Its serial interface separates the audio transport from the host processor’s general-purpose bus, allowing the audio format and sample rate to be coordinated by firmware. Programmable sample-rate support is useful when the system changes between stored-content rates, although the supported rates must be confirmed in the manufacturer datasheet. The 2.7 V minimum supply also calls for a regulator when the embedded platform operates from a lower battery voltage.
推荐
Portable Connected Audio Accessory
In a connected portable audio accessory, the WM8731CSEFL can provide the local playback path from a digital audio source to a headset. A wireless or wired digital interface handles content transfer, while the codec handles analog conversion and headphone drive. Its 28-QFN footprint limits occupied board area, and the integrated driver simplifies analog routing. Designers should keep the codec clock and power domains isolated from noisy digital activity, provide local bypass capacitance, and verify connector ground continuity to prevent channel imbalance or unintended noise.
推荐
Compact Audio Interface Module
The WM8731CSEFL is suitable for a compact module that converts digital audio from a host board into a headphone-level analog output. Because the codec and headphone driver share one package, module designers can reduce connector-to-connector routing distance and avoid a discrete output stage. The interface remains suitable for experimentation and embedded audio platforms, but pin multiplexing, clock routing, and control firmware must match the device configuration documented by the manufacturer. A prototype should also confirm that the selected module’s supply rail remains inside the 2.7 V-to-3.6 V operating window.
推荐
Portable Audio Test and Demonstration Platform
A portable audio demonstration platform can pair the WM8731CSEFL with a digital signal source to exercise the complete playback path from serial samples through the codec and headphone driver. This arrangement is useful for evaluating firmware-controlled sample rates, output channels, and system-level audio behavior. Because the compact QFN package exposes a thermal pad and fine-pitch leads, the board should follow the manufacturer’s land-pattern and assembly guidance. Bring-up should begin with confirmed clocking and supply sequencing before evaluating analog noise, distortion, channel balance, or headphone stability.
推荐
推荐产品汇总
工程参考数据: WM8731CSEFL ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | WM8731CLSEFL |
|---|---|---|
| Package | 28-QFN (5x5) | 28-QFN (5x5) |
| Brand | Cirrus Logic, Inc. | Cirrus Logic, Inc. |
| Minimum Supply Voltage | 2.7 V | 1.8 V |
| Maximum Supply Voltage | 3.6 V | 3.6 V |
| Primary Application | Portable Internet audio | Portable Internet audio |
| Product Class | Stereo codec with headphone driver | Stereo codec with headphone driver |
关键差异点
- Lower-voltage family option for portable power designs (对比 WM8731CLSEFL)
- Compact mixed-signal integration (对比 WM8731CLSEFL)
- Direct fit for 3.3 V portable systems (对比 WM8731CLSEFL)
设计说明
Design the WM8731CSEFL supply around its documented 2.7 V to 3.6 V operating range. Use separate local bypass paths for the supply pins specified by the manufacturer, place the capacitors close to the device, and verify startup behavior across the full input-voltage range. The exposed pad should follow the datasheet’s thermal and electrical recommendations. Estimated power calculations require the actual supply voltage, current, and output-load operating point and should be treated as design estimates until confirmed on the assembled board.
Separate the headphone-output and analog-input routing from digital clocks and control signals. Keep the codec clock source and traces away from high-impedance audio inputs, maintain a continuous ground reference for the audio path, and place bypass and routing components close to their relevant pins. Use the manufacturer pinout and reference layout to confirm pin-1 orientation, exposed-pad treatment, and the exact 28-QFN land pattern before fabrication.
Do not treat the WM8731CLSEFL as an unconditional substitute for the WM8731CSEFL: its documented minimum supply voltage is 1.8 V rather than 2.7 V, a 0.9 V difference. Confirm that all supply domains, clock ratios, serial formats, control-register defaults, and pin functions are acceptable for the target PCB. The WM8731CSEFL/R suffix denotes an alternate reel or packing designation and should not be treated as a separate functional replacement.
Validate the serial audio clock, data, and control traces as a complete interface rather than routing them independently. Check edge-rate requirements, trace loading, return paths, and grounding against the manufacturer’s timing and layout guidance. For analog performance, evaluate output noise, distortion, channel balance, and headphone stability with the intended cable and load. The manufacturer electrical characteristics define the test conditions needed for meaningful comparisons.
合规信息
The exact WM8731CSEFL compliance declarations require confirmation in the manufacturer product documentation or current declaration of compliance.