XMC1100T016F0064AAXUMA1 - 32MHz Cortex-M0 64KB MCU | Infineon
MPN: XMC1100T016F0064AAXUMA1 ✓ NakahandaXMC1100T016F0064AAXUMA1 Ulas
An ARM Cortex-M0 microcontroller is a compact 32-bit processor used in embedded systems. It belongs to the microcontroller hierarchy, combining a processor core, memory interface, programmable I/O, timers, communication peripherals, and interrupt control on one integrated circuit. The XMC1000 family is intended for cost-sensitive applications where deterministic control, efficient code execution, and a small package are more important than a large memory map or high pin count.
The XMC1100T016F0064AAXUMA1 combines a 32 MHz ARM Cortex-M0 core with 64 KB of Flash storage. The PG-TSSOP-16-8 package exposes the device in a 16-lead surface-mount form factor. The industrial XMC1100 product page identifies the family as an ARM Cortex-M0 industrial microcontroller with a 32 MHz core, 64 KB Flash, and TSSOP-16 package, matching the target device ordering code.
The XMC1100 series datasheet states that most peripherals use input multiplexers to select different input sources. It also notes that input paths remain active while a pin is configured as an output, allowing feedback to on-chip resources without consuming an additional external pin. This characteristic can simplify firmware configuration when a physical pin must change between input and output roles.
Typical applications include industrial sensor controllers, motor and actuator supervision, building automation, appliance control, compact power-conversion controllers, and low-cost communications equipment. The 64 KB Flash capacity is suitable for firmware that does not require a large graphical interface or extensive local data storage. For designs requiring more code space, higher clock performance, or a larger package, compare the device with other XMC1000 derivatives before finalizing the PCB.
The PG-TSSOP-16-8 footprint simplifies assembly in small-format products, but the limited pin count requires careful planning for power, ground, programming access, clocking, communications, and application I/O. Confirm the exact pin multiplexing, alternate-function restrictions, and exposed-pin assignments in the manufacturer datasheet and reference documentation before routing the board.
This page combines the manufacturer ordering information, series data sheet details, distributor listings, programming-tool support information, and practical replacement guidance for engineers evaluating the XMC1100T016F0064AAXUMA1 in embedded designs.
Mga alternatibo na pwedeng ilagay na XMC1100T016F0064AAXUMA1 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok XMC1100T016F0064AAXUMA1 (parehas na form factor at footprint) — pagkakaiba sa Flash Memory.
XMC1100T016F0064ABXUMA1
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →XMC1100T016F0064AAXUMA1 Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | 32-bit ARM Cortex-M0 microcontroller |
| Processor Core | ARM Cortex-M0 |
| CPU Frequency | 32 MHz |
| Flash Memory | 64 KB |
| Flash Organization | 64K x 8 |
| Packhaging | PG-TSSOP-16-8 |
| Bilang ng Pin | 16 pins |
| Uri ng Pagpapasok | Surface mount |
| Industrial Variant | Industrial ARM Cortex-M0 microcontroller |
| Programming Interface | Arm serial debug programming support |
| Hardware Breakpoints | 2 |
| Peripheral Input Multiplexing | Supported |
| Input Path During Output Configuration | Active |
Gabay sa Pin Configuration ng XMC1100T016F0064AAXUMA1 pg-tssop-16-8
Pin configuration para sa XMC1100T016F0064AAXUMA1 (pg-tssop-16-8 package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa XMC1100T016F0064AAXUMA1.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
XMC1100T016F0064AAXUMA1 ay nararapat para sa 6 aplikasyons: Industrial Sensor Controllers, Building Automation Modules, Appliance Control, Compact Power Conversion Control, Motor and Actuator Supervision, Communications Equipment.
Industrial Sensor Controllers
The XMC1100T016F0064AAXUMA1 fits compact industrial sensor controllers that combine digital sensing, status monitoring, and local control in a 16-pin package. Its 32 MHz ARM Cortex-M0 core provides enough processing throughput for supervisory logic, communication handling, and debounce or filtering functions, while 64 KB of Flash accommodates a focused embedded application rather than a large application framework. Peripheral input multiplexing is particularly useful when the same physical pin must support different input sources or provide feedback while configured as an output. Keep the design within the device's verified supply range and use the manufacturer Port I/O mapping to assign pins before placing connectors, sensors, and protection components around the TSSOP footprint.
Inirekomenda
Building Automation Modules
The XMC1100T016F0064AAXUMA1 is appropriate for building-automation modules that coordinate sensors, actuators, status LEDs, and serial communications on a compact board. A 32 MHz Cortex-M0 core supports responsive event handling, and the 64 KB Flash store is practical for protocol handling, scheduled control logic, configuration storage, and diagnostic routines. The PG-TSSOP-16-8 package leaves board area for connectors and isolated communication hardware, although its limited pin count makes alternate-function planning essential. Use the pin-description and Port I/O tables in the XMC1100 documentation, keep exposed pads and ground-return layout within the package recommendations, and validate the module against its environmental and isolation requirements before production use.
Inirekomenda
Appliance Control
The XMC1100T016F0064AAXUMA1 can serve as the main controller in a compact appliance when the product requires deterministic logic for buttons, relays, sensors, displays, and motor supervision. Its 32 MHz ARM Cortex-M0 core processes control tasks without a large external processor, and 64 KB of Flash provides a practical code budget for state machines, safety checks, and device communication. Programmable I/O reduces the need to reserve dedicated pins for every peripheral, but the PG-TSSOP-16-8 package still requires careful allocation of power, ground, programming signals, and communications. Confirm the exact I/O voltage and timing limits in the manufacturer data sheet, and use the pin-mapping table to ensure every motor, relay, and sensor interface has a defined operating state during reset.
Inirekomenda
Compact Power Conversion Control
The XMC1100T016F0064AAXUMA1 is useful for supervisory control in compact power-conversion equipment where an MCU coordinates PWM commands, fault flags, temperature monitoring, and communication with a dedicated converter stage. The 32 MHz Cortex-M0 core offers efficient control-loop execution, while 64 KB of Flash can hold control algorithms, parameter handling, and fault-recovery code. The TSSOP-16-8 footprint allows the controller to sit close to the power stage, reducing control-loop routing complexity, provided the PCB separates sensitive analog returns from switching currents. Review the exact timing, I/O, and electrical limits in the manufacturer data sheet, and implement hardware shutdown paths so a firmware fault cannot leave the power stage in an unsafe state.
Inirekomenda
Motor and Actuator Supervision
The XMC1100T016F0064AAXUMA1 can supervise low- to moderate-complexity motor and actuator systems where position sensing, limit detection, timing, and fault reporting must be coordinated by a small controller. A 32 MHz ARM Cortex-M0 core handles real-time control tasks, and the 64 KB Flash budget is suitable for compact algorithms and diagnostic sequences. Its programmable peripheral input paths allow sensor signals to be routed to internal resources, but the 16-pin package must still support the chosen motor driver, sensor interfaces, and fault signals. Use the complete Port I/O function mapping during schematic design, and validate timing margins at the maximum operating frequency before using the device as a direct replacement in an existing motor-control board.
Inirekomenda
Communications Equipment
The XMC1100T016F0064AAXUMA1 fits compact communications equipment that requires protocol handling, configuration, status monitoring, and control of external transceivers. The 32-bit Cortex-M0 core provides efficient 32-bit execution for packet processing and control tasks, while 64 KB of Flash is appropriate for a focused protocol stack and device firmware. Peripheral input multiplexing can make limited I/O more flexible, and the PG-TSSOP-16-8 package supports dense production boards. The MCU does not replace a network transceiver, so the final design must allocate pins for its interface, oscillator or clock source, reset, programming access, and power distribution. Confirm peripheral availability and package restrictions in the XMC1100 data sheet before assigning a communications interface.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for XMC1100T016F0064AAXUMA1 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | XMC1100T016F0064ABXUMA1 |
|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies |
| Package | PG-TSSOP-16-8 | PG-TSSOP-16-8 |
| Processor Core | ARM Cortex-M0 | ARM Cortex-M0 |
| CPU Frequency | 32 MHz | 32 MHz |
| Flash Memory | 64 KB | 64 KB |
| Product Variant | AA ordering variant | AB ordering variant |
| Programming Support | XMC1100-64 device support listed | XMC1100-64 device support listed |
Pangunahing mga Pagkakaiba
- Same documented core and memory configuration as the AB-step candidate (kumpara saXMC1100T016F0064ABXUMA1)
- Compact 16-pin surface-mount integration (kumpara saXMC1100T016F0064ABXUMA1)
- Direct fit for XMC1100-64 programming workflows (kumpara saXMC1100T016F0064ABXUMA1)
Talaan ng Disenyo
Reserve the PG-TSSOP-16-8 footprint exactly as shown in the manufacturer package drawing, including pin-1 orientation and exposed thermal-pad requirements where applicable. Place decoupling, programming-header access, and clock components close to their associated pins. Because the package has only 16 leads, finalize alternate-function allocation before routing; a pin needed later for a peripheral may require a different board revision.
Design the supply network around the device's documented operating range and verify startup, reset, and I/O voltage compatibility with every connected sensor, transceiver, or actuator. Add local high-frequency bypass capacitance and provide a clean return path to the device ground. Do not infer a 3.3 V-only system from general marketplace descriptions; confirm the exact voltage limits for this ordering code in the manufacturer data sheet.
Do not assign pins solely by their generic GPIO names. The XMC1100 family uses peripheral input multiplexing, and the manufacturer notes that an input path remains active while the pin is configured as an output. Review the complete Port I/O function mapping and alternate-function tables before finalizing the schematic, then test every pin after reset to ensure its boot and safe-state behavior matches the system design.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer identifies the XMC1100-T016F0064-AB family as industrial, but exact compliance declarations and AEC-Q100 status for the AA ordering code require current manufacturer documentation.