Ürünler (46.000+)

INA2141U - Dual 100V/µs Instrumentation Amplifier | Texas Instruments
INA2141U

INA2141U - Dual 100V/µs Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2141U is a dual-channel, low-power instrumentation amplifier with selectable gains of 10 and 100, 4 V/µs slew rate, and 1 MHz gain-bandwidth product, housed in a 16-pin SOIC (DW) package. Each channel offers a maximum input offset voltage of 50 µV, maximum offset drift of 0.5 µV/°C, and typical gain accuracy of ±0.05%. The devices support bipolar supplies up to ±18 V and include input protection to ±40 V. An instrumentation amplifier is a precision analog signal-conditioning IC that amplifies the differential voltage between two inputs while rejecting common-mode interference. Its internal architecture provides high input impedance, accurate resistor-based gain, and strong common-mode rejection. In the electronic-component hierarchy, the INA2141U is a dual instrumentation amplifier within the broader amplifier IC and signal-conditioning categories. Key features include a low maximum input bias current of 5 nA and a minimum common-mode rejection ratio of 117 dB. These characteristics suit sensor interfaces where source impedance, thermocouple voltages, and small bridge signals must be measured accurately. The low-power design also supports battery-powered instrumentation and compact test equipment where amplifier efficiency and low bias current influence overall system error. The internal gain architecture offers a choice of 10 or 100 to match both moderate and high-sensitivity measurement ranges. A 1 MHz gain-bandwidth product supports signal bandwidth required by many industrial, medical, and laboratory systems, while the 4 V/µs slew rate improves large-signal response. Maximum input offset voltage of 50 µV and drift of 0.5 µV/°C limit errors in low-level DC measurements. Typical uses include bridge excitation and readout, pressure and strain-gauge amplification, biopotential front ends, battery-powered sensor modules, current-shunt measurements, and precision data-acquisition systems. The 16-pin SOIC package allows conventional surface-mount assembly, while the dual-channel configuration can reduce board area when two differential inputs must be conditioned. Designers should use the manufacturer pin-description table to assign input, feedback, reference, power, and output connections. Input filtering, reference-grounding, and supply-bypass placement require care because parasitic resistance can degrade CMRR and offset performance. Input protection ratings should not be interpreted as a substitute for external surge protection in hazardous or high-energy systems. This page consolidates the key INA2141U specifications, verified package information, application guidance, and confirmed replacement references into a practical engineering comparison. It also distinguishes direct pin-compatible options from related INA214x devices whose gain and channel characteristics differ.

RFQ İletişim
INA2141UA - Dual G=10,100 Instrumentation Amplifier | TI
INA2141UA

INA2141UA - Dual G=10,100 Instrumentation Amplifier | TI

The Texas Instruments INA2141UA is a dual, low-power instrumentation amplifier in a 16-pin SOIC package, with signal gain options of 10 and 100 and a listed gain-bandwidth product of 200 kHz. It is designed for amplifying small differential sensor signals in industrial measurement, instrumentation, and analog front-end systems. The package is identified as 16-SOIC, measuring 0.295 inch, or 7.50 mm, in body width. An instrumentation amplifier is a precision analog amplifier optimized for differential signals. Its internal architecture amplifies the voltage difference between two inputs while rejecting common-mode noise, which is important when a sensor output is small relative to the surrounding electrical environment. The INA2141 belongs to the wider category of operational amplifier ICs and analog signal-chain devices used to condition, scale, and route sensor signals before conversion or control. Key confirmed features include dual amplifier channels, low-power operation, selectable gains of 10 and 100, a 200 kHz listed bandwidth figure, and a 16-pin SOIC package. The dual configuration allows one device to serve two independent analog channels, reducing component count when the board area is constrained. The two gain settings also support different sensor ranges without changing the overall signal-chain architecture. The device uses a three-operational-amplifier instrumentation-amplifier approach to provide differential input handling and high common-mode rejection. Exact input common-mode range, output swing, supply range, input bias current, offset voltage, noise density, and quiescent current should be confirmed in the manufacturer datasheet before the circuit is released for production. Typical uses include bridge-sensor front ends, pressure and force measurement, current-shunt monitoring, battery-cell sensing, and industrial instrumentation. The dual-channel arrangement is particularly useful when two sensors must be measured under similar electrical conditions, while the 200 kHz gain-bandwidth figure supports signal bandwidths appropriate for many slow-to-moderate industrial sensing tasks. Design layouts should provide short, symmetric input traces, a stable reference configuration, and careful grounding around the analog inputs. Because the INA2141UA operates in a differential measurement environment, input filtering, protection, and connector grounding determine whether the amplifier sees the intended signal or external interference. This page consolidates the confirmed ordering information, package details, functional attributes, application fit, and replacement considerations. It also identifies the technical parameters that should be checked in the manufacturer datasheet before schematic sign-off, helping engineers move from part selection to a validated analog front-end design.

RFQ İletişim
INA2141UG4 - Dual 10/100 Gain Instrumentation Amp | TI
INA2141UG4

INA2141UG4 - Dual 10/100 Gain Instrumentation Amp | TI

The Texas Instruments INA2141UG4 is a dual, low-power instrumentation amplifier with selectable gains of 10 or 100, a 200 kHz bandwidth at gain 100, and a 16-pin SOIC package. Each amplifier provides one instrumentation-amplifier channel, allowing two independent differential measurements in a compact surface-mount design. An instrumentation amplifier is a precision analog circuit that amplifies the voltage difference between two inputs while rejecting common-mode signals. The INA2141 belongs to the instrumentation-amplifier hierarchy within amplifier ICs and analog signal-chain conditioning. Its internal three-op-amp architecture supports current-feedback input circuitry, preserving useful bandwidth at high gain and simplifying front-end design for bridge sensors, low-voltage sensing, and industrial measurement systems. Key characteristics include two amplifiers per package, gain options of 10 and 100, 200 kHz bandwidth at a gain of 100, and a typical signal-to-noise ratio listed at 117 dB. The operating temperature range extends from -40 °C to +85 °C. The gain-setting arrangement eliminates the need for external feedback resistors, while the integrated input circuitry reduces component count and makes the device suitable for compact, high-impedance sensing nodes. Technically, the INA2141 combines differential input handling with internal feedback networks and an output amplifier in each channel. Current-feedback input circuitry is the key bandwidth feature: the specified 200 kHz gain-bandwidth behavior at gain 100 supports faster signal capture than a typical low-frequency precision-only instrumentation amplifier. The device operates from a 5 V supply and consumes approximately 15 mA, balancing channel density, measurement bandwidth, and power consumption for portable and industrial equipment. Typical uses include precision bridge excitation for pressure and load cells, current-sense amplification in power systems, battery and energy monitoring, biomedical instrumentation interfaces, and factory sensor acquisition. In bridge-based measurements, the amplifier rejects supply and ground disturbances shared by both sensor inputs. In current sensing, it magnifies a small differential shunt voltage while limiting the influence of common supply variation. A critical design consideration is input and output range: the selected gain and 5 V supply determine the usable differential and output spans. Review the absolute maximum and recommended operating conditions in the manufacturer datasheet before applying large bridge or shunt inputs. PCB placement should keep sensitive input traces short, provide a stable reference or return path, and separate analog routing from switching-converter and digital timing nodes. This page combines manufacturer electrical characteristics, package and ordering information, sourced pricing, drop-in replacement guidance, and application-focused engineering guidance. It is intended to help engineers evaluate the INA2141UG4 for precision differential measurement while identifying the key electrical and layout checks required before release to production.

RFQ İletişim
INA2143U - 5-V/µs Dual Precision Difference Amplifier | TI
INA2143U

INA2143U - 5-V/µs Dual Precision Difference Amplifier | TI

The Texas Instruments INA2143U is a dual high-speed precision difference amplifier featuring 5 V/µs slew rate, 250 µV offset, selectable gain settings of 10 or 0.1, and a 14-pin SOIC package. The device is intended for systems that measure small voltage differences and require amplified differential outputs. A difference amplifier is a specialized operational-amplifier circuit that compares voltages applied to its inverting and non-inverting inputs and amplifies the voltage between them. This method helps reject signals that appear equally on both inputs, making difference amplifiers useful within measurement, instrumentation, analog-control, and signal-conditioning systems. The INA2143U belongs to the amplifier IC category and combines two precision difference amplifiers in one package. Key features include a 5 V/µs slew rate, 250 µV offset, gain options of 10 and 0.1, dual-channel operation, and an operating temperature range of -55°C to 125°C. The 5 V/µs slew rate allows the output to respond quickly to input-voltage changes, while the selectable gain provides flexibility for different differential-signal levels. Each channel can support the two stated gain configurations. The INA2143U combines two difference amplifiers in a single 14-pin SOIC (D) package, reducing board area when two differential channels are required. Its high-speed and precision positioning makes it applicable to fast analog signal conditioning, where the main design objective is to preserve the relationship between two input voltages while converting the differential signal into a single-ended output. Typical applications include current-sense amplifier front ends, differential sensor interfaces, bridge-based measurement circuits, industrial instrumentation, and analog control systems. In a current-sense design, the amplifier processes the voltage generated across a sense resistor rather than the full supply voltage. In a bridge or differential sensor interface, it rejects common-mode voltage and preserves the smaller differential component being measured. Designers should use the manufacturer pin-description table when assigning traces and power connections, and they should verify signal amplitudes against the selected gain of 10 or 0.1. PCB placement should minimize resistive and capacitive pickup around the differential inputs, while supply bypassing should follow the connection and capacitor recommendations in the manufacturer datasheet. This page combines the confirmed INA2143U operating characteristics with practical selection guidance, application context, package information, and drop-in replacement validation. It distinguishes confirmed device attributes from parameters that require confirmation from the complete manufacturer datasheet, helping engineers plan sourcing and circuit design with fewer assumption-driven steps.

RFQ İletişim
INA217AIDWT - Low-Noise Instrumentation Amplifier | Texas Instruments
INA217AIDWT

INA217AIDWT - Low-Noise Instrumentation Amplifier | Texas Instruments

Texas Instruments INA217AIDWT is a low-noise, low-distortion monolithic instrumentation amplifier with 1.3 nV/√Hz input noise at 1 kHz, 0.004% THD+N at 1 kHz with a gain of 100, and 800 kHz bandwidth at a gain of 100. The device operates from ±4.5 V to ±18 V and is packaged in a 16-pin SOIC wide-body package. Its external-resistor gain configuration and high common-mode rejection make it suitable for precision differential-receiver front ends. An instrumentation amplifier is a specialized amplifier that measures the voltage difference between two input signals while rejecting large common-mode voltages. The INA217 belongs to the instrumentation-amplifier hierarchy within signal-chain ICs, where low input noise, accurate gain control, and common-mode rejection are more important than general-purpose op-amp flexibility. The INA217 is also identified by Texas Instruments as a replacement for the SSM2017, with its 16-pin SOIC option providing the same package and pinout as the SSM2017. The principal performance characteristics are 1.3 nV/√Hz noise at 1 kHz, greater than 100 dB common-mode rejection, and 800 kHz bandwidth at a gain of 100. Its total harmonic distortion plus noise remains only 0.004% at 1 kHz under that gain condition. Current-feedback circuitry supports wide bandwidth and dynamic response across a broad range of externally programmed gains, while the operating supply range accommodates precision laboratory, industrial, and instrumentation systems using dual rails. The INA217 uses an external gain-setting resistor, allowing the closed-loop gain to be selected according to the application. This architecture makes the device appropriate for differential sensor interfaces where source impedance is known and signal gain must be adjusted. The 16-pin wide-body SOIC provides sufficient pin count for the input, output, supply, feedback, and gain-setting connections while retaining compatibility with the referenced SSM2017 footprint. Typical uses include low-level bridge excitation and measurement, precision differential voltage acquisition, current-shunt monitoring, sensor-interface amplification, and laboratory instrumentation. In each case, the low-noise input stage preserves small differential signals, while common-mode rejection limits the effect of voltage shared by both input terminals. The wide supply range supports systems operating at rail voltages between 4.5 V and 18 V per rail. The most important PCB consideration is to follow the manufacturer’s pin-description table and recommended decoupling layout. Input and supply connections should be short, the gain resistor should connect only to the specified gain pin, and grounding should avoid shared high-current return paths. Because the device is intended for precision signal extraction, component placement and source-impedance balancing are as important as the nominal noise specification. This product page combines the INA217’s principal electrical characteristics, verified package information, sourcing guidance, replacement considerations, and application-focused engineering guidance. It also highlights where a drop-in replacement can preserve the PCB footprint and where original SSM2017 compatibility must be checked against the complete pin and electrical requirements.

RFQ İletişim
INA217AIP - Low-Noise Instrumentation Amplifier | Texas Instruments
INA217AIP

INA217AIP - Low-Noise Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA217AIP is a low-noise, low-distortion monolithic instrumentation amplifier in an 8-pin PDIP package. It accepts a 4.5 V to 18 V supply, provides a typical gain of 3 V/V, features 250 µV input offset voltage, and supports a slew rate of 15 V/µs with 3.4 MHz bandwidth. An instrumentation amplifier is a specialized amplifier optimized for measuring low-level differential signals. Its internal signal path rejects common-mode noise while amplifying the voltage difference between two inputs. The INA217 belongs to the instrumentation amplifier, differential amplifier, analog amplifier, and signal-conditioning IC hierarchy, making it suitable for precision sensor conditioning, balanced audio, industrial measurement, and medical instrumentation. The device uses current-feedback circuitry to provide wide bandwidth and strong dynamic response over a broad gain range. Its distortion-cancellation architecture is intended to maintain low distortion even at higher gain. The manufacturer identifies near-theoretical noise performance for a 200 Ω source impedance, making balanced low-impedance microphone signals a primary use case. The monolithic implementation also provides differential inputs, low noise, and low distortion in one package. INA217AIP is identified as a replacement for the SSM2017 and is available with the same DIP-8 and wide-body SOL-16 pin arrangements. The DIP-8 format is useful when an existing instrument-amplifier layout must be retained. Its 15 V/µs slew rate supports high-level audio stages, while differential input handling improves rejection of common-mode interference in measurement systems. Typical applications include professional microphone preamplification, low-level bridge or transducer signal conditioning, industrial process measurement, and medical monitoring. In a microphone circuit, the part processes the differential output of a balanced capsule while rejecting much of the shared noise appearing on both signal conductors. Its low-noise, low-distortion characteristics help preserve the signal-to-noise ratio of the source. When designing around INA217AIP, preserve the pin arrangement of the original SSM2017 layout and follow the manufacturer datasheet for gain-setting resistors, supply bypass capacitors, and output drive requirements. Check input common-mode range, output swing, and source impedance at the selected gain because instrumentation amplifiers can become input-voltage-range constrained even when their bandwidth remains adequate. This product page combines the manufacturer electrical description, package information, compatible-device context, and application-level engineering guidance. It also distinguishes direct replacements from alternatives that require different packages, helping designers evaluate PCB reuse, signal bandwidth, and noise performance before committing to a component.

RFQ İletişim
INA2181 26V Dual-Channel Current Sense Amp | TI | Gain 20 V/V
INA2181A1IDGSR

INA2181 26V Dual-Channel Current Sense Amp | TI | Gain 20 V/V

The Texas Instruments INA2181 (e.g., INA2181A1IDGSR) is a 26V, dual-channel, bidirectional, 350kHz voltage-output current sense amplifier in a 10-pin VSSOP (DGS) package, part of the cost-optimized INAx181 family. It senses voltage drops across shunt resistors on low- or high-side rails and outputs a ground-referenced analog voltage proportional to load current. A current sense amplifier (also called a current-shunt monitor) is a specialized difference amplifier that extracts a small differential shunt voltage riding on a large common-mode voltage and converts it to a ground-referenced single-ended signal. Within the signal chain hierarchy it sits between the shunt resistor and an ADC or comparator, serving as a front-end element of power management and battery monitoring systems. Key features include a wide 2.7V to 26V common-mode range that is independent of the 2.7V to 5.5V supply, 350kHz bandwidth for fast load-transient monitoring, bidirectional operation with a reference pin for charging/discharging current measurement, and factory-calibrated gain options (A1 = 20 V/V, A2 = 50 V/V, A3 = 100 V/V, A4 = 500 V/V) that eliminate gain-setting resistors. The zero-drift architecture delivers low offset for small shunt voltages. The dual channels share one package, halving board area versus two single-channel monitors such as the INA181. Rail-to-rail output swings close to the supply rails, maximizing ADC dynamic range. All device options are specified from -40C to +125C. Typical applications include battery current monitoring in portable and industrial equipment, DC motor drive phase and bus current sensing, telecom and server power supply current telemetry, and load-current supervision in 12V/24V rails feeding TI C2000 or MSPM0 MCUs. Design tip: keep the shunt voltage in the 10 mV to 100 mV range at full load - large enough to swamp offset error, small enough to limit shunt power dissipation. Route Kelvin sense traces directly to the shunt pads to preserve accuracy.

RFQ İletişim
INA2181A3IDGSR - 26V Dual-Channel Current Sense Amp | TI
INA2181A3IDGSR

INA2181A3IDGSR - 26V Dual-Channel Current Sense Amp | TI

The Texas Instruments INA2181A3IDGSR is a 26V, dual-channel, bidirectional voltage-output current sense amplifier with a fixed gain of 100 V/V (A3 version), 350 kHz bandwidth, and a common-mode input range of -0.2 V to +26 V, housed in a 10-pin VSSOP (DGS) package rated from -40C to +125C. A current sense amplifier (also called a current-shunt monitor) is a specialized difference amplifier that senses the small voltage drop across a shunt resistor and converts it into a ground-referenced output signal. Within the power-management IC hierarchy, it sits alongside voltage regulators and battery-management devices as a core building block of power monitoring and protection subsystems. Key features include the wide -0.2 V to +26 V common-mode range that operates independently of the supply voltage, enabling high-side and low-side sensing on 24 V industrial rails. The A3 gain option of 100 V/V with a 2 V/us output slew rate and 350 kHz bandwidth suits fast, medium-sensitivity current monitoring. Offset voltage is tightly specified: a maximum of plus/minus 150 uV at VCM = 0 V and plus/minus 500 uV at VCM = 12 V, according to the TI datasheet. The INAx181 architecture senses bidirectional current with an external reference voltage applied to the REF pin, allowing the output to be offset for positive and negative current indication. Rail-to-rail output swing maximizes ADC dynamic range on low-supply rails, and the cost-optimized design targets volume production. Typical applications include battery charging systems, 24 V industrial power supplies, motor drive DC bus monitoring, and telecom or server power-supply current telemetry where two channels share one shunt scheme or monitor two rails. Design consideration: keep the shunt resistor value and the A3 gain of 100 V/V balanced - a 10 mV full-scale shunt drop yields 1 V output, so size the shunt to use the ADC input range without exceeding the output swing limits. This page synthesizes distributor pricing, drop-in alternatives within the INAx181 family, and practical design notes not found in the manufacturer datasheet.

RFQ İletişim
INA2181A4QDGSRQ1 - 26V Dual 350kHz Current Sense Amp AEC-Q100 | TI
INA2181A4QDGSRQ1

INA2181A4QDGSRQ1 - 26V Dual 350kHz Current Sense Amp AEC-Q100 | TI

The Texas Instruments INA2181A4QDGSRQ1 is an AEC-Q100 qualified, 26V, dual-channel, bidirectional current sense amplifier (also called a current-shunt monitor) with a 350 kHz bandwidth and a fixed gain of 200 V/V (A4 gain variant), housed in a 10-pin VSSOP (DGS) package. It senses voltage drops across current-sense resistors at common-mode voltages from -0.2 V to +26 V, independent of its own supply voltage, and provides a rail-to-rail voltage output. A current sense amplifier is a specialized difference amplifier, within the broader hierarchy of instrumentation amplifiers and operational amplifier signal-conditioning ICs, designed to measure the small differential voltage developed across a shunt resistor and convert it into a ground-referenced output voltage proportional to load current. Bidirectional devices like the INA2181 also detect current flowing in both directions, which is essential in battery charging and discharging monitoring. Key features of the INA2181A4QDGSRQ1 include the wide -0.2 V to 26 V common-mode range that survives automotive load-dump-adjacent conditions, dual-channel integration that halves board area versus two single-channel amplifiers, a 350 kHz bandwidth suitable for fast current-loop control, and the cost-optimized INAx181-Q1 family architecture. Technically, the INA2181-Q1 uses a zero-drift-free precision front end with a fixed gain set by internal resistors; the A4 variant provides 200 V/V gain, allowing very small shunt resistances (sub-10 mOhm) to be used, reducing shunt power dissipation at high currents. The voltage output architecture requires no ADC-side gain stage and simplifies interfacing with microcontroller ADC inputs. Typical applications include automotive battery management systems, 48V and 12V automotive power rails, industrial motor drives, telecom -48V systems, and server hot-swap current monitoring. Design-wise, place the shunt resistor close to the amplifier inputs, use Kelvin (4-wire) connections to the sense resistor, and filter differential noise at the inputs. Note that the 200 V/V gain limits full-scale shunt voltage to about 20 mV for a 4 V output swing. This page synthesizes distributor pricing, drop-in same-family gain-variant alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ İletişim
INA240A1D - 20V/V Bidirectional Current Sense Amp | TI
INA240A1D

INA240A1D - 20V/V Bidirectional Current Sense Amp | TI

The Texas Instruments INA240A1D is a bidirectional, zero-drift current-sense amplifier with a gain of 20 V/V, a common-mode voltage range of -4 V to 80 V, and an 8-pin SOIC package. It measures the voltage developed across a shunt resistor on either the high side or low side of a power path and produces an analog output proportional to current. A current-sense amplifier is a specialized instrumentation amplifier that converts the small differential voltage across a current shunt into a larger, easier-to-process voltage. The INA240 family belongs to the amplifier hierarchy as a current-sense amplifier, instrumentation amplifier, analog IC, and semiconductor. Its common-mode range allows the shunt to remain near a supply rail while high voltage, high current, or both are present in the monitored circuit. The INA240A1D combines a 20 V/V gain setting with bidirectional operation and enhanced PWM rejection. Zero-drift architecture minimizes output drift as temperature changes, while the -4 V to 80 V common-mode range supports demanding industrial power systems. Its analog output can be centered near ground for bidirectional current measurement by applying the appropriate reference configuration. The device also supports unidirectional sensing when both reference pins are tied to ground. Internally, the device provides precision differential sensing, a low-offset amplifier, and an analog output stage. Because the common-mode input range is independent of the supply voltage in the relevant operating region, the INA240 can sense voltage drops across a high-side shunt without requiring the amplifier supply to exceed the sensed bus voltage. This architecture is particularly useful when PWM switching nodes create large common-mode transients. Typical applications include motor-control systems, industrial power supplies, robotics, solar inverters, battery packs, solenoid drivers, LED drivers, and protected DC power rails. The INA240A1D is especially appropriate when current must be measured bidirectionally, the shunt may sit above ground, and PWM rejection is important. A 20 V/V gain also reduces the required shunt resistance when the measured current range is relatively low. When designing the circuit, verify that the shunt power dissipation remains below its rating and that the amplifier output stays within its valid output range at maximum load current. Place the differential input traces directly across the shunt, keep them short and symmetric, and provide stable supply decoupling close to the device. Do not exceed the absolute maximum ratings for supply voltage, common-mode voltage, or input voltage. This page combines manufacturer specifications, drop-in alternatives, application guidance, and practical design notes for engineers evaluating the INA240A1D in motor, industrial, and high-side current-measurement systems.

RFQ İletişim
INA240A1PW - 80V Bidirectional Current Sense Amp | TI TSSOP-8 (Tape & Reel)
INA240A1PW

INA240A1PW - 80V Bidirectional Current Sense Amp | TI TSSOP-8 (Tape & Reel)

The Texas Instruments INA240A1PW is a -4 V to 80 V bidirectional, ultra-precise current-sense amplifier with enhanced PWM rejection, housed in an 8-pin TSSOP (PW) package with a fixed gain of 20 V/V. It senses drops across shunt resistors over a wide common-mode range independent of supply voltage and integrates a zero-drift chopper architecture that keeps input offset below 25 uV and offset drift below 100 nV/°C. What is a current-sense amplifier? A current-sense amplifier is a specialized analog IC that measures the small differential voltage developed across a shunt resistor carrying the load current, then amplifies that millivolt-level signal to a ground-referenced output that an ADC, microcontroller, or comparator can read. As a member of the power-management and amplifier IC hierarchy, the INA240 family combines a precision difference amplifier with PWM-rejection circuitry, allowing it to ignore large dV/dt transients from switching power stages while still maintaining high DC accuracy. Key features include 20 V/V gain (A1 variant), 132 dB DC common-mode rejection ratio (CMRR), a 1.5 MHz bandwidth, and 1.6 mA maximum quiescent supply current from a 2.7 V to 5.5 V supply rail. Enhanced PWM rejection suppresses transients from 60 V/ns common-mode slew events that occur when measuring current in motor-drive and solenoid circuits, allowing accurate readings through PWM edges without blanking. The INA240 architecture pairs an input EMI filter and chopper-stabilized front end with a precision output stage. The chopper stabilization shifts the 1/f noise to a higher frequency where it is filtered out, yielding the 5 uV/°C typical offset drift and 25 uV maximum input offset specified across the -40°C to +125°C operating range. Independent supply and common-mode ranges allow the IC to operate from a 3.3 V logic rail while sensing high-side current at 24 V, 36 V, or 48 V industrial bus voltages. Typical applications include 48 V brushed and brushless DC motor control, solenoid and valve current monitoring, server and telecom 12 V/24 V hot-swap current sensing, power-converter feedback, and battery-pack current monitoring in e-mobility and industrial robots. The A1 gain of 20 V/V suits low-side and high-side sensing where shunt full-scale drop is on the order of 75 mV. When designing with this device, choose the shunt resistor so that peak differential voltage at maximum load stays within the linear output range (typically 0.1 V to VS - 0.1 V), and place a 1 nF to 10 nF RC network on the input pins if the layout introduces parasitic common-mode noise. Use Kelvin (4-terminal) connection to the shunt to keep ground-loop errors out of the measurement. This page synthesizes real-time distributor pricing, drop-in alternatives, and design notes that go beyond the manufacturer datasheet, giving engineers a one-stop reference for the INA240A1PW.

RFQ İletişim
INA240A1PWR - 80V Bidirectional Current Sense Amp | TI TSSOP-8
INA240A1PWR

INA240A1PWR - 80V Bidirectional Current Sense Amp | TI TSSOP-8

The Texas Instruments INA240A1PWR is a -4 V to 80 V bidirectional, ultra-precise current-sense amplifier with enhanced PWM rejection, housed in an 8-pin TSSOP (PW) package with a fixed gain of 20 V/V. It senses drops across shunt resistors over a wide common-mode range independent of supply voltage and integrates a zero-drift chopper architecture that keeps input offset below 25 uV and offset drift below 100 nV/°C. What is a current-sense amplifier? A current-sense amplifier is a specialized analog IC that measures the small differential voltage developed across a shunt resistor carrying the load current, then amplifies that millivolt-level signal to a ground-referenced output that an ADC, microcontroller, or comparator can read. As a member of the power-management and amplifier IC hierarchy, the INA240 family combines a precision difference amplifier with PWM-rejection circuitry, allowing it to ignore large dV/dt transients from switching power stages while still maintaining high DC accuracy. Key features include 20 V/V gain (A1 variant), 132 dB DC common-mode rejection ratio (CMRR), a 1.5 MHz bandwidth, and 1.6 mA maximum quiescent supply current from a 2.7 V to 5.5 V supply rail. Enhanced PWM rejection suppresses transients from 60 V/ns common-mode slew events that occur when measuring current in motor-drive and solenoid circuits, allowing accurate readings through PWM edges without blanking. The INA240 architecture pairs an input EMI filter and chopper-stabilized front end with a precision output stage. The chopper stabilization shifts the 1/f noise to a higher frequency where it is filtered out, yielding the 5 uV/°C typical offset drift and 25 uV maximum input offset specified across the -40°C to +125°C operating range. Independent supply and common-mode ranges allow the IC to operate from a 3.3 V logic rail while sensing high-side current at 24 V, 36 V, or 48 V industrial bus voltages. Typical applications include 48 V brushed and brushless DC motor control, solenoid and valve current monitoring, server and telecom 12 V/24 V hot-swap current sensing, power-converter feedback, and battery-pack current monitoring in e-mobility and industrial robots. The A1 gain of 20 V/V suits low-side and high-side sensing where shunt full-scale drop is on the order of 75 mV. When designing with this device, choose the shunt resistor so that peak differential voltage at maximum load stays within the linear output range (typically 0.1 V to VS - 0.1 V), and place a 1 nF to 10 nF RC network on the input pins if the layout introduces parasitic common-mode noise. Use Kelvin (4-terminal) connection to the shunt to keep ground-loop errors out of the measurement. This page synthesizes real-time distributor pricing, drop-in alternatives, and design notes that go beyond the manufacturer datasheet, giving engineers a one-stop reference for the INA240A1PWR.

RFQ İletişim
INA240A2D - 50V/V Bidirectional Current-Sense Amplifier | Texas Instruments
INA240A2D

INA240A2D - 50V/V Bidirectional Current-Sense Amplifier | Texas Instruments

The Texas Instruments INA240A2D is a bidirectional, precision current-sense amplifier with a fixed gain of 50 V/V, a common-mode operating range from -4 V to 80 V, and an 8-pin SOIC package. It is designed to measure small shunt-resistor voltage drops while rejecting PWM-related transients, making it suitable for motor drives, solenoid controls, power converters, and battery systems. A current-sense amplifier is a specialized instrumentation amplifier that converts the differential voltage across a precision shunt resistor into a scaled voltage proportional to current. The INA240 belongs to the current-sense amplifier category and the broader amplifier and measurement IC hierarchy. Its bidirectional architecture supports both positive and negative current, while its negative common-mode capability allows operation below ground during the flyback interval of inductive loads. The A2 gain option provides 50 V/V amplification, allowing a small shunt drop to produce an easily measurable output. The -4 V to 80 V common-mode range supports low-voltage motor systems, industrial 24 V and 48 V buses, and automotive-style transient environments. The manufacturer identifies the device as an ultra-precise current-sense amplifier with enhanced PWM rejection. Its operating temperature range extends from -40 °C to +125 °C for industrial and automotive temperature-grade designs. The INA240 uses a differential input arrangement to reject supply ripple and common-mode voltage while measuring the shunt differential. Bidirectional operation allows the output to move above or below ground to indicate current direction. The 8-SOIC format supports conventional surface-mount assembly and provides a practical package for power-control boards where the shunt may be separated from sensitive analog circuitry. Typical uses include BLDC and brushed motor control, solenoid and relay current monitoring, DC-DC converter feedback, battery charge and discharge measurement, inverter leg monitoring, and industrial power-supply protection. The wide common-mode range is particularly useful when the sensed current is switched while the amplifier supply remains independent of the high-voltage power rail. Design the shunt and analog path carefully. Keep the differential input traces short and symmetric, place the amplifier close to the shunt, and use low-value resistors with appropriate pulse ratings. Input filtering must preserve the intended measurement bandwidth while attenuating high-frequency switching noise. Verify common-mode voltage, output swing, supply headroom, thermal performance, and amplifier saturation before committing the PCB layout. This page consolidates the device architecture, operating limits, application guidance, package details, sourcing workflow, and drop-in replacement analysis into one engineering reference. It also identifies where application-specific values must be calculated from the actual shunt resistance, current waveform, board environment, and power-supply topology.

RFQ İletişim
INA240A2DR - 50V/V Bidirectional Current Sense Amplifier | Texas Instruments
INA240A2DR

INA240A2DR - 50V/V Bidirectional Current Sense Amplifier | Texas Instruments

The Texas Instruments INA240A2DR is a bidirectional, zero-drift current-sense amplifier with a fixed gain of 50 V/V, a -4 V to 80 V common-mode input range, and enhanced PWM rejection. It is packaged in an 8-pin SOIC and operates from a single 5.5 V supply. A current-sense amplifier is a specialized amplifier that measures the voltage developed across a shunt resistor placed in a current-carrying conductor. The INA240 belongs to the current-sense amplifier hierarchy within instrumentation amplifiers and analog signal-chain ICs. It converts the small differential shunt voltage into an amplified voltage proportional to current, supporting both positive and negative current measurement. The A2 gain code sets the nominal amplification to 50 V/V. Its wide common-mode range permits sensing current above ground, at ground, and down to -4 V, which is useful in systems with inductive flyback or ground-offset returns. Bidirectional operation means that the output can represent positive or negative current without changing the basic shunt arrangement. Enhanced PWM rejection helps suppress switching disturbances commonly encountered in motor-control and power-conversion systems. The device uses a zero-drift architecture intended to provide accurate current measurement over changing temperatures and time. The manufacturer describes the INA240 family as ultra-precise and optimized for shunt-based measurements. Because the output is proportional to the shunt differential voltage, the shunt resistance determines the conversion between current and amplifier output voltage. Typical uses include motor and solenoid current monitoring, power-converter feedback, battery current measurement, industrial control systems, and automotive-style PWM systems. The 8-pin SOIC format supports conventional surface-mount assembly and compact analog layouts. Placement close to the shunt helps minimize pickup from adjacent switching nodes. Designers should verify the complete pin configuration, recommended input filtering, output-voltage range, and absolute maximum ratings in the manufacturer data sheet before layout. Kelvin routing from the shunt terminals and careful grounding are especially important because small differential signals can be corrupted by shared copper impedance or high-current return paths. This page combines the manufacturer's core INA240 characteristics with exact-MPN commercial information, same-family drop-in options, application guidance, and practical PCB considerations for engineers evaluating the INA240A2DR in a current-measurement design.

RFQ İletişim
INA240A2PW - 50V/V Bidirectional Current Sense Amp | Texas Instruments
INA240A2PW

INA240A2PW - 50V/V Bidirectional Current Sense Amp | Texas Instruments

Texas Instruments INA240A2PW is a bidirectional, precision current-sense amplifier with a gain of 50 V/V, a -4 V to +80 V common-mode voltage range, and an operating temperature range of -40 °C to +125 °C. The device is packaged in an 8-pin TSSOP (PW) package and is designed for high-side or low-side current measurement in systems exposed to fast common-mode transients. A current-sense amplifier is an instrumentation amplifier that measures the small voltage developed across a current shunt and converts it into an amplified voltage proportional to current. This device belongs to the instrumentation-amplifier and current-sense-amplifier hierarchy, where its differential measurement, low offset voltage, and common-mode rejection improve the accuracy of power, motor, solenoid, and battery monitoring systems. The A2 gain option provides 50 V/V amplification. The INA240 family operates from a 5.5 V supply and accepts common-mode voltages extending from -4 V to +80 V. Its enhanced PWM rejection is intended to suppress transient disturbance caused by switching power stages, while bidirectional operation allows measurement of positive or negative current without changing the signal path architecture. The common-mode range and PWM rejection make the INA240A2PW especially useful where the shunt is placed near a motor, actuator, or inductive load. Although the analog output must remain within the amplifier's supply-voltage limits, the input common-mode voltage can move independently across the stated -4 V to +80 V range. This separation between input common-mode capability and output-supply limits is central to correct application design. Typical uses include DC motor current control, solenoid and actuator monitoring, battery pack current measurement, industrial power conversion, and electronic loads. The precision architecture is also appropriate for systems that must recover a small shunt voltage accurately while rejecting rapidly changing voltages on the sensed power rail. For layout, route the two shunt connections as a compact, symmetric pair and minimize the area enclosed by those traces. Place the shunt and amplifier input network close together, use a low-value differential filter only where its added noise and settling behavior are acceptable, and terminate the amplifier output according to the ADC or analog front-end requirements. This page combines the manufacturer lifecycle information, verified distributor records, family-level alternatives, comparison criteria, and application-oriented design guidance for engineers evaluating the INA240A2PW as a current-sense amplifier for industrial and power-conversion systems.

RFQ İletişim
INA240A3D - 80V Current Sense Amplifier | Texas Instruments
INA240A3D

INA240A3D - 80V Current Sense Amplifier | Texas Instruments

The Texas Instruments INA240A3D is a bidirectional, ultra-precise voltage-output current-sense amplifier with an operating common-mode range of -4 V to 80 V, enhanced PWM rejection, and an 8-pin SOIC package. It is designed to measure the voltage developed across a shunt resistor in high-side or low-side current-sensing circuits while supporting common-mode voltages above the device supply voltage. A current-sense amplifier is a specialized amplifier within the instrumentation-amplifier and signal-conditioning hierarchy. It converts the small differential voltage produced by a shunt resistor into a proportional analog voltage suitable for measurement by an ADC, MCU, motor controller, or protection circuit. The INA240 family is classified as an analog signal-chain IC and is commonly placed beside a power-conversion stage to create a precision current-feedback signal. The INA240A3D combines bidirectional measurement, a wide -4 V to 80 V common-mode range, and enhanced PWM rejection. Bidirectional operation allows the output polarity to represent either positive or negative current. The negative common-mode capability is useful when a shunt is observed during a below-ground flyback interval, while the upper range supports current monitoring in systems operating well above the amplifier supply voltage. Its stated operating-temperature range is -40 °C to 125 °C. The device uses a voltage-output architecture with reference and supply connections that support system-level current measurement. Because the amplifier can operate independently of the common-mode voltage being sensed, its performance is maintained in applications where the shunt voltage swings rapidly while the amplifier remains powered from a low-voltage rail. This architecture is particularly useful in motor drives, solenoid controls, power converters, and battery-powered systems where a conventional low-voltage current-sense amplifier may leave the measurement range. Typical uses include high-side DC-link monitoring, low-side motor-return measurement, solenoid current diagnostics, power-supply telemetry, and battery charge or discharge current sensing. In these systems, the shunt is placed in the current path and connected to the differential input of the INA240A3D. The resulting analog voltage can be routed to a control ADC or comparator for regulation, fault detection, or data logging. Design the input and reference network carefully because the differential shunt voltage, amplifier supply, output range, and selected shunt resistance jointly determine usable measurement range. Keep the shunt and amplifier connections compact to minimize parasitic pickup, use a Kelvin connection where practical, and route the differential pair away from switching-node copper. The manufacturer's INA240 datasheet should be used for pin assignments, gain, input limits, output behavior, and recommended application values. This page organizes the verified INA240A3D operating limits, package information, sourcing details, replacement constraints, application guidance, and design considerations. It also distinguishes a confirmed same-package automotive alternative from incompatible package or gain variants that cannot be treated as drop-in replacements.

RFQ İletişim
INA240A3DR - 80V Current Sense Amplifier | Texas Instruments (Tape & Reel)
INA240A3DR

INA240A3DR - 80V Current Sense Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments INA240A3DR is a bidirectional, ultra-precise voltage-output current-sense amplifier with an operating common-mode range of -4 V to 80 V, enhanced PWM rejection, and an 8-pin SOIC package. It is designed to measure the voltage developed across a shunt resistor in high-side or low-side current-sensing circuits while supporting common-mode voltages above the device supply voltage. A current-sense amplifier is a specialized amplifier within the instrumentation-amplifier and signal-conditioning hierarchy. It converts the small differential voltage produced by a shunt resistor into a proportional analog voltage suitable for measurement by an ADC, MCU, motor controller, or protection circuit. The INA240 family is classified as an analog signal-chain IC and is commonly placed beside a power-conversion stage to create a precision current-feedback signal. The INA240A3DR combines bidirectional measurement, a wide -4 V to 80 V common-mode range, and enhanced PWM rejection. Bidirectional operation allows the output polarity to represent either positive or negative current. The negative common-mode capability is useful when a shunt is observed during a below-ground flyback interval, while the upper range supports current monitoring in systems operating well above the amplifier supply voltage. Its stated operating-temperature range is -40 °C to 125 °C. The device uses a voltage-output architecture with reference and supply connections that support system-level current measurement. Because the amplifier can operate independently of the common-mode voltage being sensed, its performance is maintained in applications where the shunt voltage swings rapidly while the amplifier remains powered from a low-voltage rail. This architecture is particularly useful in motor drives, solenoid controls, power converters, and battery-powered systems where a conventional low-voltage current-sense amplifier may leave the measurement range. Typical uses include high-side DC-link monitoring, low-side motor-return measurement, solenoid current diagnostics, power-supply telemetry, and battery charge or discharge current sensing. In these systems, the shunt is placed in the current path and connected to the differential input of the INA240A3DR. The resulting analog voltage can be routed to a control ADC or comparator for regulation, fault detection, or data logging. Design the input and reference network carefully because the differential shunt voltage, amplifier supply, output range, and selected shunt resistance jointly determine usable measurement range. Keep the shunt and amplifier connections compact to minimize parasitic pickup, use a Kelvin connection where practical, and route the differential pair away from switching-node copper. The manufacturer's INA240 datasheet should be used for pin assignments, gain, input limits, output behavior, and recommended application values. This page organizes the verified INA240A3DR operating limits, package information, sourcing details, replacement constraints, application guidance, and design considerations. It also distinguishes a confirmed same-package automotive alternative from incompatible package or gain variants that cannot be treated as drop-in replacements.

RFQ İletişim
INA240A3PWR - 100V/V Zero-Drift Current Sense Amp | TI
INA240A3PWR

INA240A3PWR - 100V/V Zero-Drift Current Sense Amp | TI

The Texas Instruments INA240A3PWR is a bidirectional, zero-drift current-sense amplifier with a gain of 100 V/V, a -4 V to 80 V common-mode input range, and enhanced PWM rejection, housed in an 8-pin TSSOP package. It measures the voltage developed across a shunt resistor and produces an analog output suitable for motor-control, power-delivery, and industrial monitoring systems. The wide common-mode range allows the shunt to remain above ground, below ground, or near an 80 V bus without requiring separate high-voltage sensing electronics. A current-sense amplifier is an analog signal-conditioning device that converts the small voltage across a current shunt into a larger, measurable voltage. The INA240 belongs to the instrumentation-amplifier and current-sense-amplifier hierarchy, where accurate offset behavior and common-mode rejection are essential for recovering a current measurement from a low-amplitude differential signal. Its output voltage represents the shunt differential voltage multiplied by a fixed gain of 100 V/V. The A3 gain version provides a nominal output of 1 V for every 10 mV across the shunt. Its zero-drift architecture reduces input-offset contributions that otherwise change with temperature, improving accuracy in systems that require stable current measurements over wide operating ranges. The -4 V to 80 V common-mode capability also supports sensing during transient intervals in systems containing inductive loads, while enhanced PWM rejection helps suppress errors produced by fast-switching motor-control waveforms. The INA240 family uses a voltage-output architecture and can measure current in either direction when the output is biased with a reference voltage. The reference pin permits the output to be centered around a nonzero voltage, which is important for systems that must report both positive and negative current without saturating the output at zero. A low typical supply current of 90 μA also helps reduce the overhead introduced by the measurement channel. Typical applications include three-phase inverter motor control, DC motor current monitoring, solenoid current tracking, battery-management systems, power-supply load reporting, and industrial actuator control. In a motor inverter, the device can sit beside the low-side shunt and retain usable operation through the switching transitions. In a bidirectional system, the reference voltage shifts the zero-current output level so that positive and negative current can be distinguished at a single analog input. Designers should place the shunt and amplifier inputs on a compact, symmetric trace arrangement, connect the reference pin to a low-impedance bias network when bidirectional output is required, and keep output routing away from high-voltage switching nodes. The power-supply and ground pins require careful decoupling, while input filtering should preserve the common-mode and timing performance needed by the application.

RFQ İletişim
INA240A4D - 80V Bidirectional Current Sense Amp | Texas Instruments
INA240A4D

INA240A4D - 80V Bidirectional Current Sense Amp | Texas Instruments

The Texas Instruments INA240A4D is a bidirectional, zero-drift current-sense amplifier with a -4 V to 80 V common-mode range, enhanced PWM rejection, and an 8-pin SOIC package. It operates across a -40 °C to +125 °C temperature range and is designed to measure the voltage across a shunt resistor in systems where the sensed bus can move below ground or as high as 80 V. A current-sense amplifier is an instrumentation amplifier that converts the small differential voltage developed across a shunt resistor into a proportional, amplified output voltage. The INA240 family belongs to the amplifier and instrumentation-amplifier hierarchy, where precision gain, input offset behavior, common-mode rejection, and output accuracy determine how accurately a power circuit can be monitored. Bidirectional sensing allows the same device to report positive or negative current without changing the measurement topology. The INA240A4D provides 120 dB CMRR, a 100 kHz gain-bandwidth product, approximately 90 µA input bias current, and 1.8 mA operating supply current. Its zero-drift architecture supports current measurements in motor controls, solenoid drivers, battery systems, and industrial power supplies. Enhanced PWM rejection helps preserve measurement accuracy when rapid common-mode voltage transitions are present around inductive loads. The common-mode rating is independent of the amplifier supply voltage, allowing the INA240A4D to operate with a separate low-voltage supply while monitoring a high-voltage power bus. Its negative common-mode capability is particularly useful during the flyback interval of typical solenoid applications, when the voltage at the monitored node can fall below ground. The broad 80 V positive range supports higher-voltage industrial and automotive-style systems. Typical applications include motor-current feedback, solenoid-current monitoring, battery-pack current measurement, inverter control, power-supply telemetry, and current sharing. In each case, the shunt resistor converts current into a differential voltage, while the amplifier provides a measurable output for an ADC, controller, or protection circuit. Bidirectional operation is useful where energy can flow in either direction. For layout, place the shunt and input network close to the amplifier, keep the differential input traces compact and matched, and provide a stable bypass connection near the supply pins. The input filtering and gain-setting network must be checked against the intended current range because shunt resistance, amplifier gain, and ADC input range jointly determine the usable measurement span. This product overview combines the manufacturer specifications, package details, sourcing status, and application guidance needed to evaluate the INA240A4D. Because the manufacturer identifies this orderable variant as no longer in production, engineers should confirm lifecycle status and consider an active alternate during new design qualification.

RFQ İletişim
INA240A4DR - 80V Bidirectional Current Sense Amp | Texas Instruments (Tape & Reel)
INA240A4DR

INA240A4DR - 80V Bidirectional Current Sense Amp | Texas Instruments (Tape & Reel)

The Texas Instruments INA240A4DR is a bidirectional, zero-drift current-sense amplifier with a -4 V to 80 V common-mode range, enhanced PWM rejection, and an 8-pin SOIC package. It operates across a -40 °C to +125 °C temperature range and is designed to measure the voltage across a shunt resistor in systems where the sensed bus can move below ground or as high as 80 V. A current-sense amplifier is an instrumentation amplifier that converts the small differential voltage developed across a shunt resistor into a proportional, amplified output voltage. The INA240 family belongs to the amplifier and instrumentation-amplifier hierarchy, where precision gain, input offset behavior, common-mode rejection, and output accuracy determine how accurately a power circuit can be monitored. Bidirectional sensing allows the same device to report positive or negative current without changing the measurement topology. The INA240A4DR provides 120 dB CMRR, a 100 kHz gain-bandwidth product, approximately 90 µA input bias current, and 1.8 mA operating supply current. Its zero-drift architecture supports current measurements in motor controls, solenoid drivers, battery systems, and industrial power supplies. Enhanced PWM rejection helps preserve measurement accuracy when rapid common-mode voltage transitions are present around inductive loads. The common-mode rating is independent of the amplifier supply voltage, allowing the INA240A4DR to operate with a separate low-voltage supply while monitoring a high-voltage power bus. Its negative common-mode capability is particularly useful during the flyback interval of typical solenoid applications, when the voltage at the monitored node can fall below ground. The broad 80 V positive range supports higher-voltage industrial and automotive-style systems. Typical applications include motor-current feedback, solenoid-current monitoring, battery-pack current measurement, inverter control, power-supply telemetry, and current sharing. In each case, the shunt resistor converts current into a differential voltage, while the amplifier provides a measurable output for an ADC, controller, or protection circuit. Bidirectional operation is useful where energy can flow in either direction. For layout, place the shunt and input network close to the amplifier, keep the differential input traces compact and matched, and provide a stable bypass connection near the supply pins. The input filtering and gain-setting network must be checked against the intended current range because shunt resistance, amplifier gain, and ADC input range jointly determine the usable measurement span. This product overview combines the manufacturer specifications, package details, sourcing status, and application guidance needed to evaluate the INA240A4DR. Because the manufacturer identifies this orderable variant as no longer in production, engineers should confirm lifecycle status and consider an active alternate during new design qualification.

RFQ İletişim
INA250A1PW - 36V Bidirectional Current-Sense Amplifier | TI
INA250A1PW

INA250A1PW - 36V Bidirectional Current-Sense Amplifier | TI

The Texas Instruments INA250A1PW is a bidirectional, precision current-sense amplifier with an integrated shunt resistor, a 36 V common-mode range, and a gain of 20 V/V in a 16-pin TSSOP (PW) package. It is designed to measure positive and negative current while the measured conductor operates from 0 V to 36 V, independent of the amplifier supply voltage. The integrated precision shunt removes the external shunt-resistor element while preserving calibrated current measurement. A current-sense amplifier is a specialized instrumentation amplifier that converts the voltage across a current-sensing resistor into a proportional, low-level output voltage. The INA250 belongs to the current-sense amplifier hierarchy, where it supports precision measurement, power monitoring, motor control, industrial instrumentation, and protection systems. Its integrated shunt also reduces board area compared with a discrete shunt-resistor implementation. The device provides bidirectional measurement through an externally applied reference voltage. Positive current can move the output above the reference level, while negative current moves it below that level. This arrangement allows a unidirectional amplifier output to represent both load directions and supports applications that need absolute-value or signed-current information. The 0 V to 36 V common-mode range covers many industrial, automotive-adjacent, power-supply, and motor-system rails. The INA250A1PW uses the A1 gain option, which provides 20 V/V voltage gain. Its voltage-output architecture simplifies connection to analog-to-digital converters, comparators, controllers, and monitoring systems. Because the sensing element is integrated, PCB design must preserve the defined current path and provide adequate copper width and thermal capacity for the intended current level. The TSSOP package is a surface-mount package in the TSSOP-16 family. Typical applications include high-side power-supply monitoring, bidirectional motor-current measurement, industrial control systems, battery current sensing, solenoid monitoring, and electronic protection. In these systems, the amplifier reconstructs a current-proportional voltage that can be digitized or compared with a threshold. System calibration should account for the selected gain, reference voltage, ADC resolution, and the measurement bandwidth required by the load. Design attention should focus on Kelvin routing for the reference connection, filtering around the output when the measured waveform contains high-frequency noise, and thermal verification at maximum continuous current. The integrated shunt is convenient, but PCB copper, vias, pads, and connector geometry can limit practical current and increase temperature rise. Use the manufacturer pin-description table when assigning PCB tracks and the device data sheet for the complete recommended layout. This page combines the manufacturer device description, package and operating information, practical application guidance, replacement criteria, and engineering-oriented design notes. These resources help engineers evaluate the INA250A1PW beyond a basic distributor listing while keeping pin compatibility and measurement accuracy at the center of the selection process.

RFQ İletişim
INA250A3PW - 36V Bidirectional Current Sense Amplifier | TI
INA250A3PW

INA250A3PW - 36V Bidirectional Current Sense Amplifier | TI

Texas Instruments INA250A3PW is a bidirectional precision current-sense amplifier with an integrated shunt resistor, 100 V/V gain, and operation from a 2.7 V to 36 V supply. The device measures low- and high-side current across common-mode voltages from 0 V to 36 V and is housed in a 16-pin TSSOP package. Its voltage output supports direct connection to analog-to-digital converters, controllers, and monitoring systems. A current-sense amplifier converts the voltage generated across a shunt resistor into a proportional, measurable voltage. This integrated-resistor implementation belongs to the current-shunt monitor class within precision amplifier and power-management ICs. By placing the shunt inside the amplifier package, it removes the need for a separate precision shunt while reducing layout sensitivity associated with external Kelvin connections. The INA250A3PW provides a gain of 100 V/V, allowing the 50 mΩ integrated shunt to support current measurements up to 15 A according to the family specifications. Bidirectional operation measures positive or negative current, and an external reference can establish the output operating point for zero-current offset or bipolar reporting. A 2.7 V minimum supply permits use in low-voltage systems while the 36 V supply rating supports higher-voltage industrial buses. The INA250 family specifies a maximum supply current of 300 µA and operation from -40 °C to 125 °C. Its integrated shunt and Kelvin-connected internal structure improve measurement accuracy by reducing lead and trace resistance effects. The voltage-output architecture requires downstream filtering and input/output stability capacitors selected according to the manufacturer datasheet, rather than relying on an internal shunt resistor placed outside the package. Typical applications include motor and solenoid current monitoring, power-supply telemetry, battery-pack management, industrial control systems, and high-side or low-side protection. The device can monitor current in systems whose supply voltage changes independently of the sensed common-mode voltage, making it useful in 24 V industrial equipment, automotive-style loads, and distributed power architectures. Design layouts should keep the power path short and use solid copper planes so that shunt heat is distributed rather than concentrated in a narrow trace. Confirm output saturation, reference-pin behavior, common-mode limits, and filter-component values against the manufacturer datasheet before operating at the 15 A family limit. This page combines device specifications, application guidance, pin and package considerations, lifecycle information, and verified replacement analysis. It also distinguishes electrically similar family members from true pin-compatible drop-in choices so that PCB reuse decisions are based on measurable electrical differences rather than package similarity alone.

RFQ İletişim
INA253A1IPW - 80V Bidirectional Current Sense Amp | TI
INA253A1IPW

INA253A1IPW - 80V Bidirectional Current Sense Amp | TI

The Texas Instruments INA253A1IPW is an 80 V bidirectional precision current-sense amplifier with PWM rejection and an integrated 2 mΩ precision, low-inductance shunt resistor, packaged in a 20-pin TSSOP. The device accepts a supply voltage of 2.7 V to 5.5 V and operates across a -40°C to 125°C temperature range. It converts the voltage developed across the integrated shunt into an amplified analog output that can be measured by an ADC, controller, or protection circuit. A current-sense amplifier is a specialized amplifier that measures the voltage across a current sensor and produces an output proportional to the sensed current. The INA253 belongs to the instrumentation-amplifier and current-sensing IC hierarchy, where its integrated shunt combines current measurement with low-inductance sensing. This integration simplifies the power path and supports bidirectional measurement, allowing positive and negative current to be represented around a common zero-current output level. Key features include an 80 V common-mode input range, bidirectional current sensing, PWM rejection, zero-drift operation, and an integrated 2 mΩ shunt resistor. The A1 gain option provides a 50 V/V output ratio. The 20-pin TSSOP package provides a compact surface-mount format for industrial, automotive-adjacent, communications, and power-supply control systems where measured current must withstand substantial switching-node transients. The integrated shunt is the defining technical feature. A low-inductance sensing element limits the voltage spikes that would otherwise appear when current changes rapidly. The PWM-rejection architecture reduces disturbance from switching waveforms, while the zero-drift input stage improves accuracy around zero current. Compared with a discrete shunt-and-amplifier implementation, the INA253 reduces board area and component count while retaining the gain and common-mode ratings needed for demanding power-conversion circuits. Typical uses include DC-DC converter output-current monitoring, bidirectional motor-control current measurement, battery and power-path monitoring, and protection in industrial equipment. The 80 V common-mode capability is especially useful when the sensed conductor sits near a switching node. The integrated shunt also makes the device suitable for compact instrumentation where external Kelvin routing and discrete shunt placement would increase complexity. For PCB design, keep the high-current path electrically short and place the amplifier and its decoupling capacitors close to the supply pins. Review the manufacturer datasheet's layout example for the recommended shunt and grounding arrangement. Confirm that the analog output remains within the input range of the receiving ADC, and account for amplifier output swing and system offset when defining trip thresholds. This page combines the manufacturer's key INA253A1IPW specifications with same-package family alternatives, package details, application guidance, and selection considerations. It is intended to help engineers identify the correct gain and automotive options without overlooking common-mode rating, shunt integration, temperature range, or PCB-layout requirements.

RFQ İletişim
INA253A2IPW - 80V Bidirectional Current Sense Amp | TI
INA253A2IPW

INA253A2IPW - 80V Bidirectional Current Sense Amp | TI

The Texas Instruments INA253A2IPW is a bidirectional, zero-drift current-shunt monitor with an integrated 2 mΩ shunt resistor, 200 mV/A gain, and a 20-pin TSSOP package. It operates from a 2.7 V to 5.5 V supply while monitoring common-mode voltages from -4 V to +80 V. The device combines precise current measurement with PWM rejection in a single surface-mount IC. A current-sense amplifier is an instrumentation amplifier that measures the small voltage generated across a shunt resistor and converts it into a proportional output voltage. The INA253 belongs to the current-sense amplifier hierarchy, where it bridges precision analog measurement and power-system monitoring. Integrating the shunt resistor reduces external component count and helps standardize the sensing element for bidirectional current applications. Key electrical features include 350 kHz -3 dB bandwidth, 2.4 V/µs slew rate, 90 pA input bias current, and 1.8 mA supply current. The A2 gain version produces 200 mV/V output for each ampere of sensed current. Its wide -4 V to +80 V common-mode range allows the shunt path to operate at high bus voltages while the amplifier itself remains powered from a low-voltage supply. Internally, the zero-drift architecture supports low offset behavior in precision measurement systems. The integrated precision shunt and chopper-stabilized amplifier are designed for systems where board space, component count, and current-direction measurement are important. Because the sensing element is integrated, PCB design should preserve the manufacturer-recommended current-path geometry and thermal conditions. Typical applications include motor-drive phase current monitoring, industrial power-supply control, battery current measurement, solenoid current sensing, and LED driver feedback. The -4 V to +80 V common-mode capability is particularly useful in systems where a shunt can be placed in a high-voltage conductor while the INA253 remains connected to a 2.7 V to 5.5 V control supply. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks, especially for IN+, IN−, REF, OUT, and supply connections. Account for shunt heating at sustained high current and place input and reference components close to the device to minimize added error and pickup from fast-switching nodes. This page organizes the electrical characteristics, application guidance, confirmed family alternatives, and design trade-offs of the INA253A2IPW. It helps engineers distinguish what the integrated 2 mΩ solution provides from lower-current sensing approaches and from gain variants in the same INA253 family.

RFQ İletişim