Ürünler (46.000+)

INA253A2IPW - 80V Bidirectional Current Sense Amp | TI
INA253A2IPW

INA253A2IPW - 80V Bidirectional Current Sense Amp | TI

The Texas Instruments INA253A2IPW is a bidirectional, zero-drift current-shunt monitor with an integrated 2 mΩ shunt resistor, 200 mV/A gain, and a 20-pin TSSOP package. It operates from a 2.7 V to 5.5 V supply while monitoring common-mode voltages from -4 V to +80 V. The device combines precise current measurement with PWM rejection in a single surface-mount IC. A current-sense amplifier is an instrumentation amplifier that measures the small voltage generated across a shunt resistor and converts it into a proportional output voltage. The INA253 belongs to the current-sense amplifier hierarchy, where it bridges precision analog measurement and power-system monitoring. Integrating the shunt resistor reduces external component count and helps standardize the sensing element for bidirectional current applications. Key electrical features include 350 kHz -3 dB bandwidth, 2.4 V/µs slew rate, 90 pA input bias current, and 1.8 mA supply current. The A2 gain version produces 200 mV/V output for each ampere of sensed current. Its wide -4 V to +80 V common-mode range allows the shunt path to operate at high bus voltages while the amplifier itself remains powered from a low-voltage supply. Internally, the zero-drift architecture supports low offset behavior in precision measurement systems. The integrated precision shunt and chopper-stabilized amplifier are designed for systems where board space, component count, and current-direction measurement are important. Because the sensing element is integrated, PCB design should preserve the manufacturer-recommended current-path geometry and thermal conditions. Typical applications include motor-drive phase current monitoring, industrial power-supply control, battery current measurement, solenoid current sensing, and LED driver feedback. The -4 V to +80 V common-mode capability is particularly useful in systems where a shunt can be placed in a high-voltage conductor while the INA253 remains connected to a 2.7 V to 5.5 V control supply. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks, especially for IN+, IN−, REF, OUT, and supply connections. Account for shunt heating at sustained high current and place input and reference components close to the device to minimize added error and pickup from fast-switching nodes. This page organizes the electrical characteristics, application guidance, confirmed family alternatives, and design trade-offs of the INA253A2IPW. It helps engineers distinguish what the integrated 2 mΩ solution provides from lower-current sensing approaches and from gain variants in the same INA253 family.

RFQ İletişim
INA253A3IPW - 400mV/A Bidirectional Current Sense | Texas Instruments
INA253A3IPW

INA253A3IPW - 400mV/A Bidirectional Current Sense | Texas Instruments

The Texas Instruments INA253A3IPW is a precision current-shunt monitor with a 400 mV/A gain, an 80 V common-mode range, and an integrated 2 mΩ low-inductive shunt resistor in a 20-pin TSSOP package. It supports bidirectional current measurement from -4 V to +80 V while combining a zero-drift chopped amplifier with integrated shunt-resistor current sensing. A current-shunt monitor is an instrumentation amplifier that measures the small voltage generated across a precision shunt resistor as current flows through a conductor. The INA253 belongs to the current-sense amplifier hierarchy, where the amplified shunt voltage is filtered, digitized, or used for power monitoring and control. Its integrated resistor simplifies the sensing path, reduces external component count, and keeps the shunt geometry close to the amplifier for improved measurement repeatability. The A3 gain option provides 400 mV/A, while the INA253 family also includes 100 mV/A and 200 mV/A versions. The device operates over a -4 V to +80 V common-mode range, independent of its supply voltage, which supports high-side sensing in 48 V industrial, communications, automotive, and power-system environments. Its 350 kHz -3 dB bandwidth accommodates dynamic current measurements while providing rejection of PWM-related disturbances. The INA253A3IPW combines precision zero-drift signal conditioning with an integrated 2 mΩ shunt. Bidirectional operation allows the output to move above or below ground depending on current direction. The listed operating-temperature range is -40°C to +125°C, and the device is supplied in a 20-pin TSSOP package measuring 0.173 inch, or 4.40 mm, in width. Typical uses include server and telecom power rails, industrial motor controls, battery-management systems, LED drivers, solenoid drivers, and automotive load monitoring. In each application, the shunt monitor converts bidirectional current into a proportional analog voltage, allowing a controller to monitor load current, detect overcurrent, or implement closed-loop power management. PCB layout is critical because the integrated shunt and amplifier must be placed directly in the current path. High-current conductors should use short, wide copper, while the supply and ground connections should follow the manufacturer’s pin-assignment and layout guidance. Designers should also account for output settling, filter selection, and common-mode transient protection when operating near rapidly switching power stages. This product page combines the exact ordering information, electrical characteristics, family-level comparison, and application guidance needed to plan an INA253A3-based current-measurement design. It also identifies which same-package alternatives can be evaluated when gain, automotive qualification, or supply requirements differ.

RFQ İletişim
INA293B1QDBVRQ1 - 110V, 1.3MHz Current Sense Amp | TI
INA293B1QDBVRQ1

INA293B1QDBVRQ1 - 110V, 1.3MHz Current Sense Amp | TI

The Texas Instruments INA293B1QDBVRQ1 is an AEC-Q100 qualified, ultra-precise bidirectional current-sense amplifier that measures voltage drops across shunt resistors over an exceptionally wide common-mode range from -4 V to +110 V. It delivers a 1.3 MHz small-signal bandwidth with a 20 V/V fixed gain (B1 variant) in a 5-pin SOT-23 (DBV) package, making it ideal for high-voltage, high-precision current monitoring in space-constrained automotive and industrial designs. What is a current-sense amplifier? A current-sense amplifier is a specialized analog building block that measures the small differential voltage developed across a shunt resistor placed in series with a load or supply rail, and converts it to a ground-referenced output voltage proportional to load current. Unlike a general-purpose op amp, a current-sense amplifier tolerates large common-mode voltages - often well above its own supply - and rejects the common-mode component, exposing only the shunt drop. The INA293-Q1 sits at the high-precision end of this category, combining low offset, low drift, and the widest common-mode range in TI's portfolio of unidirectional/bidirectional current-sense amplifiers. Key features include a maximum offset voltage of ±30 µV across temperature, ±0.2% gain error, and a quiescent current of approximately 1.5 mA over the -40 °C to +125 °C automotive grade-1 temperature range. The B1 gain variant provides 20 V/V; the B2, B3, B4, and B5 variants in the same family offer 50 V/V, 100 V/V, 200 V/V, and 500 V/V respectively, all sharing the SOT-23-5 footprint. The device operates from a single 2.7 V to 20 V supply and is robust against input transients well beyond its supply rail. Internally, the INA293-Q1 uses a precision chopped-input front end followed by a fixed-gain output stage, achieving CMRR greater than 100 dB at DC and PSRR above 80 dB at 1 kHz. The wide common-mode architecture supports both high-side and low-side sensing topologies, enabling accurate monitoring in 48 V mild-hybrid automotive systems, industrial 24 V/36 V/48 V rails, and telecom -48 V applications without level shifting. Typical applications include 48 V eMobility battery management, BLDC motor phase-current monitoring, server/AI accelerator hot-swap current telemetry, USB Power Delivery contract current sensing, and solar inverter string monitoring. Compared with isolated current transducers, the INA293-Q1 achieves comparable accuracy at a fraction of the BOM cost and PCB area. When designing with this device, place the shunt resistor as close as possible to the input pins and keep the input traces symmetrical to preserve CMRR. A 0.1 µF supply bypass capacitor placed within 5 mm of the V+ pin is recommended for stable operation across the full -4 V to +110 V common-mode range. This page synthesizes distributor pricing, drop-in alternatives from the INA293-Q1 family and competing high-side current-sense amplifiers, and practical design notes that go beyond the manufacturer datasheet.

RFQ İletişim
INA321EA/2K5 - Micropower RRO Instrumentation Amplifier | Texas Instruments
INA321EA/2K5

INA321EA/2K5 - Micropower RRO Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA321EA/2K5 is a single-supply micropower CMOS instrumentation amplifier with 40 uA typical quiescent current, less than 1 uA shutdown current, and a 500 uV maximum offset specification. It provides rail-to-rail output, 94 dB common-mode rejection, 10 pA bias current, and external-resistor gain control in an 8-pin VSSOP (DGK) package. An instrumentation amplifier is a differential analog amplifier optimized for measuring small signals superimposed on a larger common-mode voltage. The INA321 belongs to the hierarchy of instrumentation amplifiers, differential amplifiers, amplifier ICs, and analog semiconductors. Its differential input stage rejects common-mode interference while amplifying the voltage difference between its input terminals, making it useful for bridge sensors, biomedical instrumentation, and low-voltage current measurement. Key features include a typical operating current of 40 uA, an offset voltage specified by the manufacturer at 500 uV maximum, a common-mode rejection ratio of 94 dB, and an input bias current of 10 pA. The shutdown function reduces quiescent current to below 1 uA. Its rail-to-rail output can approach the positive supply rail to within 0.02 V, while gain is established with external resistors. The high input impedance and low bias current are especially valuable when sensing high-source-impedance sensors. The amplifier uses a CMOS instrumentation-amplifier architecture optimized for low power and single-supply operation. With a gain of 5 V/V, the listed bandwidth is 500 kHz, providing useful bandwidth for slow biomedical signals, industrial bridges, and general-purpose differential measurements. Because the output approaches the positive rail, correct common-mode range and output-swing calculations remain essential when operating near the supply limit. Typical uses include low-power bridge-sensor conditioning, portable medical instrumentation, battery-powered sensor acquisition, current-shunt measurement, and precision analog front ends. The 40 uA operating current supports energy-limited systems, while shutdown supports duty-cycled measurement in which the amplifier remains inactive between readings. The low bias current minimizes disturbance from high-impedance sources. When designing the circuit, place the gain-setting resistors close to the amplifier and verify the complete input and output common-mode range against the actual signal. If the input is unipolar, bias it near mid-supply rather than allowing a negative input excursion. Do not substitute a similarly packaged instrumentation amplifier unless its pin functions, gain architecture, common-mode range, and output-swing behavior have all been checked. This product page combines the manufacturer's device specifications with practical application guidance, package information, pin mapping, sourcing guidance, and a comparison of available same-family choices. These engineering details help shorten component selection while keeping the decision focused on electrical compatibility rather than package name alone.

RFQ İletişim
INA326EA/250 - 1kHz Precision Instrumentation Amplifier | TI
INA326EA/250

INA326EA/250 - 1kHz Precision Instrumentation Amplifier | TI

The Texas Instruments INA326EA/250 is a precision, low-drift CMOS instrumentation amplifier with rail-to-rail input and output operation, 100 µV maximum input offset voltage, 114 dB typical gain bandwidth at 1 kHz, and 33 nV/√Hz typical input noise. The device is supplied in an 8-pin VSSOP (DGK) package and operates from 2.7 V to 5.5 V. An instrumentation amplifier is a specialized analog amplifier optimized for measuring small differential signals while rejecting common-mode interference. Its internal architecture provides gain, differential sensing, and input common-mode rejection in one device. Within the broader hierarchy, an instrumentation amplifier is an amplifier IC and a precision signal-conditioning component used ahead of converters, sensors, and data-acquisition systems. The INA326 family is designed for systems requiring low drift, low noise, and rail-to-rail signal-chain flexibility. Key characteristics include one amplifier channel, a 0.1 V/V to 1000 V/V programmable gain range, rail-to-rail inputs and outputs, a 2.7 V to 5.5 V supply range, and operation from -40 °C to 85 °C. The combination of 100 µV maximum input offset and 33 nV/√Hz typical noise supports accurate extraction of low-level differential signals. The 1 kHz gain-bandwidth characteristic makes the device suitable for precision rather than high-speed signal acquisition. The INA326EA/250 uses a CMOS implementation to combine low input bias current, low offset voltage, and low drift with rail-to-rail input and output behavior. Because its output can approach the supply rails, downstream circuitry can use a wide portion of the available analog voltage range. Its programmable gain allows one device family to serve applications ranging from modest differential amplification to high-gain sensor conditioning while preserving the same 8-pin footprint. Typical uses include bridge and strain-gauge signal conditioning, low-level current measurement, precision sensor interfaces, medical instrumentation, industrial process measurement, and data-acquisition front ends. The device is particularly appropriate when the target signal is differential, the common-mode environment is demanding, and measurement accuracy matters more than wideband throughput. A suitable analog-to-digital converter can then digitize the conditioned output. A key design consideration is to preserve the differential nature of the input signal. Keep input routing compact, use symmetric interconnections where practical, and place the gain-setting resistor close to the RG pin. Follow the Texas Instruments datasheet pin-description table when assigning PCB tracks, and confirm that the selected gain, supply voltage, and output-swing requirements remain compatible with the intended sensor. This page consolidates the Texas Instruments product characteristics, ordering information, package details, technical comparisons, and application guidance for engineers evaluating the INA326EA/250. It also organizes drop-in ordering options, practical design considerations, and search-focused technical information into one engineering reference.

RFQ İletişim
INA327EA/250 - Precision Rail-to-Rail INA | Texas Instruments
INA327EA/250

INA327EA/250 - Precision Rail-to-Rail INA | Texas Instruments

Texas Instruments INA327EA/250 is a precision, low-drift CMOS instrumentation amplifier with rail-to-rail input and output, shutdown support, a 1 kHz gain-bandwidth product, and a 10-pin VSSOP (DGS) package. It operates from 2.7 V to 5.5 V and is designed for low-side current sensing, sensor conditioning, and measurement systems requiring accurate differential amplification with minimal drift. An instrumentation amplifier is a specialized amplifier that combines differential input sensing, high input impedance, precise gain setting, and common-mode rejection in one package. This functional category belongs to the amplifier IC hierarchy, where precision instrumentation amplifiers outperform general-purpose operational amplifiers in applications that must measure small differential signals while rejecting large common-mode voltages. The INA327 provides a 1 kHz gain-bandwidth product, rail-to-rail input and output operation, an input bias current of 200 pA, and a common-mode input range that extends beyond the positive and negative supply rails. Its true single-supply architecture supports operation from a single 2.7 V to 5.5 V supply, while low DC errors and low drift suit precision measurement equipment. The INA327EA/250 uses an external resistor network to establish gain, allowing the amplifier to be adapted to different sensor scales without changing the integrated circuit. Its CMOS input stage supports low input bias current and broad common-mode range, although the relatively narrow 1 kHz bandwidth makes it more appropriate for current, temperature, pressure, and slowly varying sensor signals than for wideband signal chains. Typical applications include shunt-based current measurement in power-conversion systems, low-side motor and solenoid monitoring, bridge-sensor signal conditioning, battery current sensing, and precision industrial instrumentation. The shutdown function can reduce supply demand when the measurement channel is not active, while the 10-pin VSSOP package supports compact surface-mount layouts. The principal design consideration is input filtering. Gain-setting resistors and the instrument-amplifier inputs should be positioned close to the device, with differential and common-mode filtering selected carefully to preserve differential accuracy and common-mode rejection. The power rails must remain within the 2.7 V to 5.5 V operating limits, and unused inputs should be connected according to the manufacturer pin-description table. This page combines manufacturer ordering information, package and operating details, drop-in alternatives, application guidance, PCB considerations, and a parameter-by-parameter comparison to support faster component selection and implementation.

RFQ İletişim
INA331IDGKR - 25 V/V Rail-to-Rail Instrumentation Amp | TI
INA331IDGKR

INA331IDGKR - 25 V/V Rail-to-Rail Instrumentation Amp | TI

The Texas Instruments INA331IDGKR is a low-power, single-supply CMOS instrumentation amplifier with a closed-loop gain of 25 V/V, 2.0 MHz bandwidth, and 5 V/us slew rate, housed in an 8-pin VSSOP (DGK) package. It is designed for low-cost, high-gain accuracy with gain set by external resistors, 0.02% gain accuracy, and a 2 ppm/°C temperature coefficient. Additional headline specifications include ±250 µV offset voltage, 90 dB CMRR, and rail-to-rail operation. An instrumentation amplifier is a differential-input analog signal-conditioning IC that amplifies the voltage difference between two sensors while rejecting common-mode interference. The INA331 belongs to the hierarchy of instrumentation amplifier, differential amplifier, analog amplifier, and amplifier IC. It is used where a small sensor differential must be measured accurately in the presence of larger common-mode voltages, particularly in battery-powered industrial, medical, and portable systems. Key features include gain accuracy of 0.02% and a gain temperature coefficient of 2 ppm/°C for gains above 5 V/V. The device has an input offset voltage of ±250 µV, low input bias current, 90 dB CMRR, and a 2.0 MHz bandwidth. Its 5 V/us slew rate supports faster signal transitions, while single-supply and rail-to-rail operation simplify systems operating from a low-voltage source. The low-power design is suited to portable instrumentation and sensor interfaces. The INA331 uses external gain-setting resistors, allowing the closed-loop gain to be adjusted for the required measurement range without changing the package. At the specified 25 V/V gain, the device combines useful bandwidth for low-frequency sensor measurements with common-mode rejection for noisy industrial environments. The input and output stages operate from a single supply, reducing the number of rails required in portable equipment. Typical applications include low-side current sensing in battery systems, differential pressure and temperature measurement, biomedical instrumentation, portable sensor acquisition, industrial bridge excitation, and precision current measurement. The INA331 is especially appropriate when the sensor output is small, the required gain is above 5 V/V, and system power consumption must remain low. When implementing the circuit, place the gain-setting resistors close to the gain inputs and keep the input differential loop area small to minimize noise pickup. Check the common-mode input range at the selected supply voltage and gain because the amplifier must remain within its valid operating region. Decoupling capacitors should be positioned close to the supply pins, with the layout verified against the manufacturer reference layout. This page combines the exact orderable part information, package characteristics, gain and common-mode performance, application guidance, replacement analysis, and PCB considerations needed to evaluate INA331IDGKR before implementation.

RFQ İletişim
INA333AIDGKR - 50uA Zero-Drift INA | Texas Instruments
INA333AIDGKR

INA333AIDGKR - 50uA Zero-Drift INA | Texas Instruments

The Texas Instruments INA333AIDGKR is a low-power, precision, zero-drift instrumentation amplifier with a 1.8 V to 5.5 V supply range, 10 uV typical input offset voltage, 150 kHz bandwidth, and an 8-pin VSSOP (DGK) package. It uses a three-operational-amplifier architecture and one external gain-setting resistor to provide gains from 1 to 1000. An instrumentation amplifier is a differential analog amplifier optimized for measuring small voltage signals superimposed on larger common-mode voltages. Its internal three-op-amp topology provides high input impedance and accurate differential gain, making it more practical than a discrete difference amplifier when source impedances are unequal or signals arrive from sensors. INA333 belongs to the precision amplifier hierarchy: instrumentation amplifier, operational amplifier, analog IC, and semiconductor. The INA333 emphasizes low power, low offset drift, and rail-to-rail output operation. Verified source data identifies a 50 uA typical supply current and a gain equation of G = 1 + 100 kΩ/RG. The 150 kHz bandwidth supports fast sensor signals, while the 10 uV input offset specification improves measurement resolution around the zero-input condition. Its input stage is designed to reject common-mode variation encountered in bridge, current-sense, and portable sensing systems. The zero-drift architecture reduces temperature-related offset movement, helping preserve measurement stability when the sensor signal is small relative to input offset. Rail-to-rail output increases usable output swing on low-voltage supplies, although engineers must still verify input common-mode range, output swing, bandwidth, and input bias behavior across the complete intended voltage and temperature range using the manufacturer datasheet. Typical uses include portable medical monitoring, battery-powered industrial instrumentation, pressure and load-cell signal conditioning, low-side current measurement, and low-voltage sensor acquisition. The 50 uA power budget is especially useful for wearable and remote systems where every microamp affects battery life. The VSSOP-8 package supports compact layouts, but differential routing and gain-resistor placement remain essential. For best results, connect the gain resistor close to the RG pins, use a low-noise reference supply, maintain symmetric input routing, and follow the datasheet bypass recommendations. Verify common-mode limits at every operating point rather than assuming rail-to-rail input. This page combines verified distributor data, manufacturer specifications, sourcing guidance, and practical design context.

RFQ İletişim
INA333SHKQ - Zero-Drift Instrumentation Amplifier | Texas Instruments
INA333SHKQ

INA333SHKQ - Zero-Drift Instrumentation Amplifier | Texas Instruments

Texas Instruments INA333SHKQ is a micro-power, zero-drift, rail-to-rail output instrumentation amplifier with a closed-loop gain range of 100 to 1000 V/V. It is offered in an 8-pin HKQ ceramic flat package and is rated for operation from -55°C to +210°C. The high-temperature grade makes the device suitable for precision sensing systems that require stable amplification under extended thermal exposure. An instrumentation amplifier is a specialized analog amplifier optimized for measuring small differential signals while rejecting common-mode interference. Its internal differential architecture preserves signal integrity when the inputs share substantial common-mode voltage. Within the broader semiconductor hierarchy, an instrumentation amplifier belongs to the amplifier IC family and combines precision input, gain-setting, and differential-to-single-ended conversion functions in one device. The INA333SHKQ supports closed-loop gains from 100 to 1000 V/V. At a gain of 100, the manufacturer lists a maximum input offset voltage of 25 µV, a typical drift of 0.2 µV/°C, and noise density of 55 nV/√Hz. Its listed common-mode rejection is at least 100 dB at a gain of 10. These characteristics make the amplifier suitable for bridge-based sensors where small millivolt-level differential outputs must be measured accurately. The device operates from a single 1.8 V to 3.5 V supply according to the INA333 family specifications. Its rail-to-rail output stage permits the output voltage to approach the supply limits, improving utilization of low-voltage signal chains. A single external resistor sets the gain, simplifying implementation while preserving accurate differential amplification. The micro-power operating current supports battery-operated instrumentation where continuous sensor monitoring is required without excessive load. Typical uses include pressure and force transducers, thermocouple and RTD interfaces, biomedical instrumentation, portable measurement systems, and industrial process-control equipment. The -55°C to +210°C operating range distinguishes the SHKQ grade from the standard commercial INA333 variants and supports use in high-temperature measurement environments. When laying out an INA333SHKQ circuit, route the differential input and gain-resistor connections as short, symmetric traces, and place input filtering close to the source. Check common-mode input limits at the selected supply voltage because the allowable input range is not independent of supply. Confirm output headroom at the required gain and load, especially in low-voltage systems where rail-to-rail output behavior is important. This page combines the high-temperature INA333SHKQ specifications with application guidance, package information, engineering design notes, and a careful drop-in replacement assessment. It is intended to help engineers determine whether the device fits a precision sensing application without overlooking gain, temperature, supply, or PCB-footprint constraints.

RFQ İletişim
INA333SJD - Precision Micro-Power Instrumentation Amplifier | TI
INA333SJD

INA333SJD - Precision Micro-Power Instrumentation Amplifier | TI

Texas Instruments INA333SJD is a low-power, zero-drift, rail-to-rail-output instrumentation amplifier packaged in an 8-pin SOIC-8 (JD) package. Its headline characteristics include a 1.8 V to 5.5 V supply range, 150 kHz gain-bandwidth product, 10 µV offset voltage, and 2 nA input bias current. The device is intended for precision low-level sensor measurements where low offset, low drift, high common-mode rejection, and low input bias current are more important than wide bandwidth. An instrumentation amplifier is a differential-input amplifier designed to amplify a small voltage difference between two inputs while rejecting common-mode voltage. The INA333 belongs to the broader zero-drift amplifier family, combining an instrumentation-amplifier architecture with chopper-stabilized low-offset behavior. A zero-drift amplifier continuously corrects its own offset error, allowing low input-referred offset to remain stable over time and temperature. The INA333SJD supports gains of 1, 10, 100, and 1000 through its RG pin. Manufacturer specifications identify a maximum offset voltage of 25 µV at a gain of 100, offset drift of 0.2 µV/°C at a gain of 1000, input noise of 55 nV/√Hz at a gain of 100, and minimum common-mode rejection of 100 dB at a gain of 10. Its 0.16 V/µs slew rate supports relatively slow sensor signals without requiring a high-speed amplifier. The rail-to-rail output allows the output voltage to approach the supply rails, improving usable signal range in low-voltage systems. Gain is established by a single external resistor on the RG pin, simplifying circuit implementation while keeping the gain-setting component outside the amplifier. The measured gain error also depends on the tolerance and temperature coefficient of that resistor, so precision applications should use a suitable resistor network. Typical uses include bridge-based pressure and strain measurements, low-current sensors, biomedical instrumentation, industrial process monitoring, and portable sensor systems. The device is particularly useful when sensor output is small, common-mode voltage is substantial, and thermal offset variation would otherwise dominate the measurement. The principal design trade-off is bandwidth versus precision: the INA333 prioritizes low offset and low drift, while its 150 kHz gain-bandwidth product is modest compared with general-purpose high-speed amplifiers. Designers should also evaluate the high-temperature variant indicated by the INA333SJD ordering information and verify the complete electrical limits for the intended operating range. This product page consolidates the verified manufacturer and distributor details, identifies the practical benefits of zero-drift operation, and organizes the device's gains, noise, offset, supply, package, and application constraints for faster engineering selection.

RFQ İletişim
INA4180AIPWR-Q1 - Quad 26V Current Sense Amp, 20 V/V | TI
INA4180AIPWR-Q1

INA4180AIPWR-Q1 - Quad 26V Current Sense Amp, 20 V/V | TI

The Texas Instruments INA4180AIPWR-Q1 is an automotive-grade, quad-channel voltage-output current-sense amplifier (current-shunt monitor) in a 14-pin TSSOP (PW) package. It senses voltage drops across current-sense resistors at common-mode voltages from -0.2 V to +26 V, independent of the 1.7 V to 5.5 V supply, with a fixed gain of 20 V/V (A1 version) and 350 kHz bandwidth. A current-sense amplifier is a specialized difference amplifier that measures the small voltage developed across a shunt resistor and converts it into a ground-referenced output signal. Within the power-management IC hierarchy, it sits between the shunt element and an ADC or controller, enabling precise current monitoring for system control and protection in automotive and industrial power rails. Key features include the wide -0.2 V to 26 V common-mode range that survives load-dump and cold-crank conditions without external circuitry, four independent amplifiers in one package that reduce BOM cost and board area in multi-rail designs, rail-to-rail output for maximum ADC dynamic range, and offset voltage as low as [DATA_NEEDED: Vos]. The extended -40C to +125C operating range and AEC-Q100 qualification make it suitable for under-hood and body electronics applications. Architecturally, the INAx180 family integrates a precision matched resistor network that sets the gain (A1 = 20 V/V, A2 = 50 V/V, A3 = 100 V/V, A4 = 200 V/V), eliminating external gain-setting resistors and their matching errors. The zero-crossover-compatible input stage supports sensing on the low side or high side of the rail, and the output is referenced to ground regardless of common-mode voltage. Typical applications include automotive battery current monitoring, 48V and 12V board-net supervision, electric power steering motor current feedback, DC-DC converter current loops, and industrial PLC analog input modules. Cost-optimized designs benefit from the quad-channel integration. Design tip: choose the shunt resistor so the full-scale drop is 10-50 mV to balance accuracy against power dissipation, and use Kelvin (4-wire) connections to the shunt for best precision. Pricing shown as of 2026-08-29.

RFQ İletişim
INA597IDGKT - Precision 2MHz Difference Amplifier | TI
INA597IDGKT

INA597IDGKT - Precision 2MHz Difference Amplifier | TI

The INA597IDGKT is a high-precision, wide-bandwidth difference amplifier from Texas Instruments, designed for cost-sensitive applications requiring accurate differential signal measurement. It integrates a precision operational amplifier with a matched resistor network, achieving a maximum offset voltage of 200 µV and an offset drift of 5 µV/°C. The device operates from a single supply of 4.5 V to 36 V or dual supplies of ±2.25 V to ±18 V, with a bandwidth of 2 MHz and a common-mode rejection ratio (CMRR) of 88 dB. Housed in an 8-pin VSSOP (DGK) package, the INA597IDGKT is suitable for space-constrained designs. A difference amplifier is a type of operational amplifier circuit that amplifies the voltage difference between two inputs while rejecting common-mode voltages. It is a fundamental building block in analog signal processing, often used in current sensing, bridge amplification, and precision measurement systems. The INA597 belongs to the broader category of instrumentation amplifiers, which are specialized for accurate differential signal acquisition in noisy environments. Key features of the INA597IDGKT include its low offset voltage and drift, which ensure accurate measurement over temperature, and its high CMRR of 88 dB, which rejects common-mode noise. The device also offers rail-to-rail output, allowing maximum dynamic range in single-supply applications. Its low power consumption makes it ideal for battery-powered and portable instrumentation. The INA597 uses TI's e-trim™ technology, which provides precision trimming of the internal resistor network to achieve excellent gain accuracy and temperature stability. The integrated resistors are laser-trimmed to maintain tight matching, ensuring consistent performance across the operating temperature range. The device is fully specified for operation from -40°C to +125°C, making it suitable for industrial and automotive environments. Typical applications include motor current sensing, battery management systems, and precision data acquisition. In motor control, the INA597IDGKT can measure the voltage across a shunt resistor to monitor current, providing feedback for closed-loop control. In battery management, it can sense charge/discharge currents with high accuracy. The device's wide supply range and rail-to-rail output also make it suitable for industrial process control and test equipment. When designing with the INA597IDGKT, ensure that the input common-mode voltage remains within the specified range to maintain linearity. The reference pin (REF) allows level shifting of the output, which is useful in single-supply applications where the output must be centered at a specific voltage. Proper PCB layout with short traces and adequate bypassing will optimize performance.

RFQ İletişim
INA790A-Q1 - 110V 75ARMS Ultra-Precise Current Sense Amp | TI
INA790A-Q1

INA790A-Q1 - 110V 75ARMS Ultra-Precise Current Sense Amp | TI

The Texas Instruments INA790A-Q1 is an AEC-Q100 qualified, 110V, 75ARMS integrated-shunt ultra-precision current-sense amplifier with enhanced PWM rejection, housed in a 15-VSON (DEK) 6x6 mm package. It combines a calibrated 400 micro-ohm Kelvin-connected shunt resistor with a zero-drift chopped amplifier, delivering +/-35 ppm/degrees C temperature drift and bidirectional current measurement from -4V to +110V common-mode. What is a current-sense amplifier? A current-sense amplifier is an analog IC that measures the voltage across a shunt resistor placed in series with a load and amplifies the small differential voltage into a ground-referenced output proportional to load current. Current-sense amplifiers sit within the signal-chain hierarchy as follows: current-sense amplifier -> instrumentation amplifier -> analog amplifier -> power management analog IC. INA790A-Q1 belongs to the integrated-shunt subfamily, where the shunt resistor and the gain stage are co-packaged, eliminating PCB layout-induced Kelvin errors and parasitic resistance drift that plague discrete solutions. Key features include a -4V to +110V wide common-mode range that survives load-dump and cold-crank transients in 48V automotive rails, 75ARMS continuous current handling, enhanced PWM rejection that suppresses large dv/dt common-mode steps from switching power stages, 1.3 MHz bandwidth for fast transient response, and a low 35 ppm/degrees C maximum temperature drift enabled by the chopper-stabilized architecture. The integrated 400 micro-ohm shunt eliminates external resistor stocking, drift concerns, and board-space overhead. The INA790A-Q1 uses a zero-drift chopper architecture that modulates the input offset voltage to a higher frequency, samples the modulation envelope, and feeds back to cancel the original offset. This technique virtually eliminates the 1/f noise corner and the offset drift that limit conventional current-sense amplifiers in high-precision DC and slow-varying measurements. Typical applications include 48V automotive BLDC motor phase current sensing, server and telecom hot-swap controller current monitors, industrial solenoid and actuator current feedback, solar inverter string current measurement, and battery management system (BMS) pack-current sensing. The AEC-Q100 Grade 1 qualification and PWM rejection make it specifically tailored to inverter and motor-drive environments. When designing with this device, place the INA790A-Q1 in the Kelvin path as close to the load current shunt as possible. Because the shunt is internal, the only PCB layout concern is keeping high-current traces off the analog ground return. Use the REF pin to level-shift the output for bidirectional sensing into an ADC with a ground-referenced input. This page synthesizes TI datasheet parameters, DigiKey pricing, INA790A vs INA790B comparison, and practical design notes not found in the manufacturer datasheet alone.

RFQ İletişim
INA791B-Q1 - 110V 75A High-Bandwidth Current Sense Amp | Texas Instruments
INA791B-Q1

INA791B-Q1 - 110V 75A High-Bandwidth Current Sense Amp | Texas Instruments

The Texas Instruments INA791B-Q1 is an AEC-Q100-qualified, ultra-precise bidirectional current-sense amplifier with integrated 75A EZShunt technology, supporting a common-mode voltage range of -4V to +110V independent of supply. Housed in a 14-pin DFN (DEK) package measuring approximately 2.5 mm x 3 mm, the B-grade variant offers enhanced precision over the A-grade, including tighter gain error and offset drift specifications optimized for high-accuracy current measurement in automotive and industrial systems. A current-sense amplifier is an analog IC that measures the small differential voltage developed across a shunt resistor carrying a large load current, while rejecting the large common-mode voltage present at the shunt terminals. The category belongs to the instrumentation amplifier family, itself a subclass of operational amplifiers used in measurement and protection subsystems. Current-sense amplifiers sit in the signal chain between the power stage and the MCU/ADC, enabling telemetry, overcurrent protection, and closed-loop control in DC/DC converters, motor drivers, and battery management systems. Key features of the INA791B-Q1 include a wide -4V to +110V common-mode range, high bandwidth for fast transient response, support for 75A RMS continuous current via the integrated EZShunt resistor, and a single 2.7V to 5.5V supply drawing only 3.75 mA maximum quiescent current. The B-grade variant delivers tighter initial accuracy and lower drift than the A-grade, making it well-suited to precision telemetry across the automotive temperature range of -40C to +125C. The architecture combines a precision chopper-stabilized front end with an EZShunt integrated shunt element, eliminating external sense resistors while maintaining high CMRR across the entire common-mode range. The device outputs an analog voltage proportional to load current that can be routed directly to an ADC input for software-based current monitoring, fault detection, and coulomb counting. Typical applications include 48V automotive electrical systems, battery management in HEV/EV powertrains, motor control in body and chassis ECUs, solenoid and actuator monitoring, and industrial high-voltage bus telemetry. The integrated shunt simplifies PCB layout and reduces parasitic inductance that otherwise degrades high-di/dt measurement accuracy. When designing with this part, route the high-current path directly through the integrated EZShunt pins to minimize parasitic resistance, and place a low-ESR decoupling capacitor close to the VS pin. The bidirectional capability means the output polarity indicates current direction, which simplifies charge/discharge monitoring in battery systems.

RFQ İletişim
INA819IDR - 35µV Offset Low-Power Instrumentation Amp | Texas Instruments
INA819IDR

INA819IDR - 35µV Offset Low-Power Instrumentation Amp | Texas Instruments

The Texas Instruments INA819IDR is a low-power (350 µA), high-precision instrumentation amplifier housed in an 8-pin SOIC (D) package, offering 35 µV maximum offset voltage, 8 nV/√Hz input-referred noise density, and ±60 V overvoltage protection on the gain-setting pins (pins 2 and 3). A single external resistor sets any gain from 1 to 10,000, making it a flexible analog front-end building block. An instrumentation amplifier (INA / in-amp) is a precision differential amplifier that combines high input impedance, accurate fixed gain, and excellent common-mode rejection ratio (CMRR). It is constructed from internal op-amps and a precision resistor network; the user only programs the gain with one external resistor. Within the analog signal-chain hierarchy, instrumentation amplifiers sit above standard op-amps and are the preferred first stage for low-level, high-CMRR sensor readout, before downstream ADCs, SAR drivers, or programmable-gain stages. The INA819 targets precision industrial, medical, and test-and-measurement designs that demand excellent DC accuracy and very low broadband noise. Key specifications include 35 µV maximum input offset voltage, 0.4 µV/°C maximum offset drift, 8 nV/√Hz voltage noise density, 120 dB minimum CMRR (G = 100), 7 MHz bandwidth (G = 100), and 1.6 V/µs slew rate. The super-beta input stage delivers very low input bias current (10 nA maximum) and high input impedance, supporting direct connection to high-impedance bridges and transducers without external buffers. Architecturally, the INA819 combines a super-beta bipolar input front-end with a current-feedback gain stage and laser-trimmed thin-film resistors, achieving <0.4 µV/°C drift and 120 dB CMRR at 1 kHz. It supports single-supply 4.5 V to 36 V or dual-supply ±2.25 V to ±18 V operation, suiting both battery-powered and industrial 24 V bus rails. Typical applications include bridge pressure-strain gauge signal conditioning, weigh scales, ECG/biopotential front ends, industrial process-control analog inputs, and battery-cell monitoring AFE stages. The ±60 V input protection (gain pins only) allows direct connection to industrial sensor lines without external clamping in many cases. When designing with the INA819, choose the gain resistor close to the INA pins to minimize parasitic capacitance and maintain CMRR above 100 dB. For highest DC accuracy, add a low-pass RC filter at the output to attenuate RF rectification before the ADC. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes - engineering context not found in the manufacturer datasheet alone.

RFQ İletişim
INA950-SEP - 80V Ultra-Precise Current-Sense Amp | TI
INA950-SEP

INA950-SEP - 80V Ultra-Precise Current-Sense Amp | TI

The INA950-SEP from Texas Instruments is a space-enhanced product (SEP) current-sense amplifier designed for ultra-precise current measurements in high-reliability applications. It senses the voltage drop across a shunt resistor over a wide common-mode range from 2.7V to 80V, making it ideal for high-side current sensing in systems with large supply voltages. The device operates from a single 2.7V to 5.5V supply while drawing only 370μA (typical) of quiescent current, and is available in the TSSOP-8 package. A current-sense amplifier is a specialized operational amplifier that measures current by amplifying the small differential voltage across a sense resistor while rejecting the common-mode voltage. It is a key building block in power management systems, enabling accurate monitoring of load currents, battery charging, and power supply health. The INA950-SEP belongs to the family of analog current-sense amplifiers, which are essential for closed-loop control and protection in industrial, automotive, and aerospace systems. Key features include a wide common-mode input range of 2.7V to 80V, a bandwidth of 1.1MHz, and ultra-precise gain accuracy. The device is designed for space applications, offering enhanced radiation tolerance and reliability. Its low quiescent current of 370μA minimizes power consumption, making it suitable for battery-powered and energy-harvesting systems. The TSSOP-8 package provides a compact footprint for space-constrained PCBs. Technically, the INA950-SEP uses a precision current-sense architecture that maintains high accuracy across temperature and supply variations. The wide common-mode range allows it to monitor currents on high-voltage rails without level shifting, simplifying system design. The 1.1MHz bandwidth enables fast transient response, which is critical for detecting overcurrent conditions in real time. Typical applications include high-side current sensing in power supplies, battery management systems, motor control, and load switches. In space applications, it is used for power monitoring in satellites and spacecraft, where reliability and precision are paramount. The device's wide common-mode range and low power consumption make it versatile for both high-voltage and low-power systems. When designing with the INA950-SEP, ensure that the shunt resistor is placed in the high-side path and that the common-mode voltage does not exceed the absolute maximum rating. Proper PCB layout with Kelvin connections to the shunt resistor is essential to minimize parasitic resistance and maintain measurement accuracy.

RFQ İletişim
IPQ8072 - Quad-core Wi-Fi 6 SoC, 2.2GHz, Networking Pro 1200 | Qualcomm
IPQ8072

IPQ8072 - Quad-core Wi-Fi 6 SoC, 2.2GHz, Networking Pro 1200 | Qualcomm

The Qualcomm IPQ8072 is a quad-core 64-bit ARM Cortex-A53 networking system-on-chip (SoC) operating up to 2.2 GHz, integrated into Qualcomm's Networking Pro 1200 platform for premium Wi-Fi 6 (802.11ax) routers, gateways, and mesh systems. It supports up to 12 spatial streams across 2.4 GHz, 5 GHz, and 6 GHz bands when paired with QCN9074 or QCN9024 companion radios, delivers up to 5.4 Gbps aggregate PHY rate, and ships in a 772-ball FCBGA package. The die integrates a quad-core CPU subsystem, dual-band MAC/BB blocks, dedicated packet engine hardware, and security acceleration. A Wi-Fi 6 SoC is a system-on-chip that consolidates the application processor, Wi-Fi baseband/MAC, networking offloads, and crypto engines into a single die, replacing what was historically a CPU-plus-discrete-Wi-Fi-chipset architecture. Within the platform hierarchy, the IPQ8072 sits at the premium tier of Qualcomm's Networking Pro family, between the mid-range IPQ6018/IPQ6024 series and the Wi-Fi 7 flagship IPQ9574. It is intended for carrier-grade CPE, enterprise access points, and retail tri-band/quad-band routers that demand deterministic MU-MIMO and OFDMA scheduling. Key differentiating features include 12-stream 8x8 + 4x4 MU-MIMO with OFDMA, hardware-accelerated encryption (IPSec/L2TP/SSL/TLS) via dedicated engines, a quad-core A53 CPU at 2.2 GHz for control plane and SDK extensibility, support for up to 2.5 Gbps Ethernet (HSGMII/PSGMII), and integrated RF/PHY for simultaneous tri-band operation. The 14 nm process node and 772-ball FCBGA package enable compact router designs with reduced BOM. Architecturally, the IPQ8072 pairs a quad-core CPU cluster with hardware packet processing accelerators, offloading NAT, QoS, and crypto from the CPU to maintain wire-speed throughput. The integrated Wi-Fi subsystem supports 1024-QAM, MU-MIMO uplink/downlink, OFDMA, BSS coloring, target wake time (TWT), and dynamic frequency selection (DFS) for global regulatory compliance. The Networking Pro 1200 platform framing also brings platform-level features like Qualcomm's Wi-Fi SON (Self-Organizing Network) for mesh. Typical applications include Wi-Fi 6 tri-band/quad-band consumer routers, carrier-grade gateways, enterprise access points, mesh nodes, and small-business firewalls. The wide temperature range and carrier-grade SDK make it suitable for industrial deployments and outdoor CPE. When designing with IPQ8072, allocate at least 6 layers of PCB stack-up with continuous ground planes beneath the FCBGA, follow Qualcomm's reference thermal solution (heat spreader plus 1 oz copper pour), and validate PCIe/NSS pin assignments against the QSDK BSP for your chosen QCN radio companion. Use M.2 or mPCIe slots to attach QCN9074 5 GHz or 6 GHz radio cards. This page synthesizes distributor stock, package-level drop-in alternatives, and reference design considerations beyond the raw datasheet - including the IPQ8072A stepping upgrade and the sibling IPQ8074 (higher-end) / IPQ6018 (mid-range) alternatives.

RFQ İletişim
IR4301MTRPBF - 160W Mono Class D Audio Amplifier | Infineon
IR4301MTRPBF

IR4301MTRPBF - 160W Mono Class D Audio Amplifier | Infineon

The Infineon IR4301MTRPBF is a 1-Channel (Mono) Class D integrated digital audio amplifier that delivers up to 160W into a 4 ohm load from a 22-pin PowerVQFN (5x6 mm) package. The part integrates a PWM controller, a high-voltage gate driver, and two low-RDS(on) MOSFETs into a single multichip module, and it accepts a fully differential or single-ended analog input with no DSP required. According to the Infineon IR4301M datasheet, the device achieves a typical output noise floor of 250 uVrms and operates from a split or single power supply. A Class D audio amplifier is a switching amplifier topology that drives the loudspeaker with pulse-width modulated square waves at hundreds of kHz, then low-passes them in the speaker itself. The IR43x1 family therefore belongs to the audio amplifier IC class of products, which itself sits inside the broader amplifier IC and integrated circuit hierarchy. Compared with classic linear (Class AB) amplifiers, Class D designs reach efficiencies above 90 percent, which lets the IR4301M deliver high peak music power without a mechanical heatsink in typical music playback use. Key features include integrated analog input with no MCU code required, high peak music power output, no mechanical heatsink requirement, split or single supply operation, and differential or single-ended input. Integrated protections cover over-current, over-temperature, and under-voltage conditions. The 5 mm by 6 mm PQFN22 footprint exposes the die to a thermal pad that conducts waste heat to the PCB copper, which is the primary cooling path in compact audio products. The IR4301M multichip module uses an optimized co-packed MOSFET pair driven by a dedicated controller, so the gate drive and dead time are matched to the output stage. High voltage ratings and noise immunity in the controller IC ensure reliable operation over a wide range of environmental conditions. The amplifier is specified for industrial temperature grade and supports both bridge-tied-load and single-ended output configurations through the same pinout. Typical applications include soundbars, subwoofers, mini-component stereo systems, portable Bluetooth speakers, and integrated active speaker modules. The device is also used in automotive aftermarket amplifiers and pro-sumer desktop audio. Designers choose this part when they need a small, thermally friendly mono Class D stage that can be driven directly from an analog audio source. When designing with the IR4301M, place the LC output filter components close to the device and provide a substantial copper pour on the exposed pad to dissipate the idle losses. The datasheet recommends a ferrite-core inductor around 10 to 22 uH and an X7R film or ceramic filter capacitor matched to the load impedance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone. The IR43x1 family covers the IR4301M, IR4311M, and IR4321M, which differ mainly in output power and supply voltage rating.

RFQ İletişim
IR4302MTRPBF - 2-Ch Class D 130W Stereo Amp | Infineon
IR4302MTRPBF

IR4302MTRPBF - 2-Ch Class D 130W Stereo Amp | Infineon

The Infineon IR4302MTRPBF is a 2-channel integrated analog-input Class D audio amplifier IC that combines a dual-channel PWM controller, a high-voltage gate driver, and four low-RDS(on) digital audio MOSFETs in a single 44-pin PQFN (7x7 mm) package. According to manufacturer datasheet, it delivers up to 130 W peak music output per channel into 4 ohm loads, operates from a split or single ±21 V (or single 10 V to 42 V) supply, and provides differential or single-ended analog inputs. Differential analog noise floor is specified at 250 uVrms, and the part integrates standard Class D protections including over-current, over-temperature, and under-voltage lockout. A Class D audio amplifier is a switching-mode power amplifier that uses pulse-width modulation (PWM) at hundreds of kHz to drive the output stage, achieving efficiencies typically above 90% - compared with 50-65% for Class AB designs - by ensuring the output transistors are either fully on or fully off. This topology minimizes quiescent dissipation, eliminates the need for large mechanical heatsinks, and allows much smaller form-factor designs. The IR4302MTRPBF exemplifies the integrated Class D trend: rather than discrete controller + MOSFET half-bridges, the silicon and the power stage are co-packaged and co-optimized, which reduces parasitic loop inductance, EMI, and PCB layout effort. Key features that distinguish this part include: no mechanical heatsink required for typical music playback, selectable single or split supply operation, differential or single-ended analog inputs, integrated protection features (over-current, over-temperature, under-voltage), small 7x7 mm PQFN-44 footprint, and high peak music power output versus its physical size. The IR4302 family shares the same PQFN-44 package across its variants (IR4302 and IR4312), simplifying PCB reuse. Typical applications include consumer home-theater receivers, soundbars, powered desktop speakers, musical instrument amplifiers, automotive head-unit subwoofer channels, and multichannel AVR systems. In each case the device's high efficiency, small PCB footprint, and integrated protection reduce total BOM and thermal-management complexity versus discrete Class D solutions. Design consideration: layout the output LC filter with low-ESR ferrite or powdered-iron inductors and film or ceramic capacitors placed close to the amplifier outputs, and keep the analog input ground return separated from the high-current power ground until they join at the bulk-decoupling capacitor. Use an RC snubber across the output to reduce EMI if required by the standard in your region (e.g., FCC Part 15, EN55032). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ İletişim
IRS20124C Audio Digital Driver IC | Infineon
IRS20124C

IRS20124C Audio Digital Driver IC | Infineon

Infineon Technologies IRS20124C is an integrated-circuit audio digital driver described by the verified distributor data as “IC AUDIO DVR DGTL HI/LO DIE.” The device is listed by DigiKey as an audio channel device and is positioned for digital audio signal-driving applications. Its verified package, channel count, electrical ratings, timing characteristics, thermal limits, and exact pin assignments are not included in the supplied records, so those details remain identified as data-needed rather than inferred. An audio digital driver is a signal-path integrated circuit, or interface IC, that converts or conditions digital-audio signals for connection to downstream audio circuitry. In the broader hierarchy, it belongs to digital signal conditioning, then interface ICs, then semiconductor components. Compared with a passive line driver, an integrated audio driver can consolidate multiple digital channels and associated protection or interface functions, but its exact implementation must be confirmed from the manufacturer datasheet. The verified data specifically identifies the IRS20124C as an audio special-purpose device with high-side and low-side digital drive circuitry. This description suggests that the part is intended to provide controlled digital output behavior rather than serving as an analog audio amplifier. The distributor wording also references “die,” but it does not disclose die dimensions, process technology, clocking requirements, or isolation details. Potential uses include digital audio links, audio equipment, powered speaker or headphone systems, and other systems requiring a dedicated audio digital-drive interface. The correct application cannot be finalized without the electrical limits, package drawing, logic thresholds, timing, and pinout. Engineers should compare those verified values against the target system before selecting the part. When integrating the IRS20124C, verify supply voltage, input and output logic levels, propagation delay, channel configuration, and exposed-pad requirements in the manufacturer documentation. Do not assume SOIC, QFN, leadless, or other package options solely from the suffix. Distributor ECAD records can contain multiple package interpretations, making the exact manufacturer part document controlling. This page consolidates distributor classification, sourcing links, and the precise limitations of the available records. It deliberately avoids invented electrical specifications, package assumptions, pricing, pin assignments, or replacement claims while identifying what must be obtained before design release.

RFQ İletişim
IRS20124CD - 200V Digital Audio Driver | Infineon
IRS20124CD

IRS20124CD - 200V Digital Audio Driver | Infineon

Infineon Technologies IRS20124CD is a digital audio driver IC designed for Class D amplifier output stages, with verified source information identifying a 200 V high-voltage rating and support for programmable dead-time generation. It is associated with the IRS20124S family, whose manufacturer description identifies integrated dead-time generation and bidirectional over-current sensing for simplified output-stage design. The device is intended to drive discrete power transistors rather than directly delivering loudspeaker current, making external MOSFET or IGBT selection an important part of amplifier design. A digital audio driver is a gate-drive IC used between a Class D controller and the power switching transistors in an audio amplifier. It translates control signals into high-voltage gate drive, manages timing between complementary switching devices, and can provide protection functions. This places the IRS20124CD in the broader power-management and audio-amplifier hierarchy: Class D amplifier controller, digital audio driver, discrete power stage, loudspeaker output. The verified family information highlights programmable dead-time through the DT/SD pin, allowing external resistor-based timing adjustment with only two external resistors. Proper dead-time prevents simultaneous conduction in the complementary output devices, while bidirectional over-current sensing helps the amplifier react to abnormal output-stage conditions. These features are central to designing a robust discrete switching stage rather than relying on uncontrolled gate timing. The IRS20124CD is associated with up to 1000 W output-power capability in Class D audio applications according to the supplied IRS20124S family source snippet. The exact electrical ratings, thermal limits, package dimensions, and pin assignments for the CD suffix were not present in the verified data, so those values must be confirmed against the Infineon manufacturer datasheet before layout or production use. The family is particularly relevant to powered speakers, subwoofers, PA systems, and automotive or industrial audio equipment where a discrete MOSFET output stage is preferred. Designers should treat the IRS20124CD as a high-voltage gate driver, not as a complete audio amplifier. External switching transistors, DC-link voltage, current sensing, dead-time components, gate resistors, heat sinking, and output filtering must be designed together. The family’s programmable dead-time and bidirectional current sensing reduce control complexity, but exact component values and protection thresholds require the manufacturer datasheet. This page distinguishes verified family-level information from CD-suffix-specific data that is unavailable in the supplied results. It also emphasizes practical selection criteria, including package confirmation, voltage rating, gate-drive compatibility, current limits, thermal performance, and amplifier topology before treating any substitute as a true drop-in replacement.

RFQ İletişim
IRS2052MTRPBF - 2-Ch 200V Class D Audio Driver | Infineon
IRS2052MTRPBF

IRS2052MTRPBF - 2-Ch 200V Class D Audio Driver | Infineon

The Infineon IRS2052MTRPBF is a 2-channel (stereo) high-voltage Class D audio amplifier driver IC integrating dual PWM modulators, gate drivers, and comprehensive protection features in a 48-pin MLPQ (7x7 mm) package. It supports an analog audio input and drives external complementary power MOSFETs in a half-bridge or full-bridge output stage, delivering high-efficiency amplification suitable for subwoofer, two-channel, and bridge-tied load (BTL) Class D topologies. A Class D audio amplifier is a switching amplifier topology that uses pulse-width modulation (PWM) to drive the output stage fully on or fully off, dramatically reducing power dissipation compared to a linear (Class A/B) amplifier. The IRS2052M occupies the 'controller + gate driver' layer of the audio amplifier hierarchy (Class D controller -> audio amplifier -> amplifier IC -> signal chain IC -> semiconductor), making it the brain and gate-drive interface between the analog audio front end and the high-current MOSFET output stage. Key features include a 200 V high-voltage rating (suitable for ±100 V rails), programmable dead-time, integrated over-current and over-temperature protection, clipping detection output for dynamic speaker management, and a versatile shutdown control that supports latched, non-latched, or host-controlled modes. The IRS2052M operates from a logic supply and a high-voltage bootstrap supply, enabling self-powered gate drive for the high-side MOSFETs of each half-bridge. The device integrates proprietary PWM modulation with adjustable switching frequency (typically 400 kHz to 800 kHz range) to balance audio band noise rejection against switching losses. An external thermal sensor input allows system-level thermal monitoring beyond the on-chip thermal shutdown, critical in space-constrained multi-channel amplifiers and automotive audio systems. Typical applications include powered subwoofers, home theater receivers, automotive head units and external amplifiers, professional powered speakers, and marine/PA systems. Its 200 V rating enables high-power designs (several hundred watts per channel) with appropriate output MOSFET selection and output filter design. When designing with the IRS2052M, prioritize gate-drive loop layout to minimize parasitic inductance on the high-current path, and carefully select bootstrap capacitor values based on switching frequency and high-side MOSFET gate charge. Always pair the IRS2052M with logic-level or standard-threshold MOSFETs whose total gate charge supports the programmed switching frequency without exceeding the IC's drive capability. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ İletişim
IRS2053MPBF - 3-Channel 6.2W Class-D Amplifier | Infineon
IRS2053MPBF

IRS2053MPBF - 3-Channel 6.2W Class-D Amplifier | Infineon

The Infineon Technologies IRS2053MPBF is a three-channel Class-D digital audio power amplifier rated for a 10 V to 15 V supply and 6.2 W output power, housed in a 48-pin MLPQ package measuring 7 mm by 7 mm. It integrates the modulator, power-stage, and protection functions needed to drive three audio channels efficiently. Programmable bidirectional current sensing protects the high-side and low-side MOSFETs from overcurrent conditions. Its surface-mount MLPQ construction supports compact Class-D audio systems where reduced board area and efficient power conversion are important. A Class-D audio amplifier is a switching power amplifier that uses pulse-width modulation to represent an audio waveform. Unlike a linear audio amplifier, it spends less time between the positive and negative supply rails, improving power-conversion efficiency and reducing heat in many listening-power applications. The IRS2053MPBF sits within the hierarchy of audio amplifiers, power amplifiers, switching amplifiers, and power-management semiconductors. The verified product information identifies three amplification channels, Class-D operation, a 6.2 W output-power rating, and a 10 V to 15 V supply-voltage range. Its integrated current-sensing function is a key protection feature for the output power stage. The small MLPQ48 package is specifically associated with the smaller physical footprint made possible by Class-D topology, although exact output power per channel, efficiency, modulation frequency, thermal resistance, and load limits require confirmation from the manufacturer datasheet. Typical uses include compact powered speakers, multimedia speaker systems, consumer audio equipment, and other multi-channel sound systems powered from a 10 V to 15 V source. A three-channel device is useful when one board must drive multiple speakers or separate audio zones. System designers should account for supply headroom, speaker impedance, filtering, amplifier stability, PCB thermal performance, and the protection requirements of each output stage. For layout, the exposed thermal and electrical features of the MLPQ package require careful copper and via treatment according to the manufacturer recommendations. The audio output filter should be selected for the switching characteristics and load, while input and supply routing should be kept compact. Because verified thermal, frequency, protection-delay, and electrical-limit details are unavailable in the supplied excerpts, those values must be checked against the complete manufacturer datasheet before release to production. This page consolidates the verified distributor and datasheet-index information, separates confirmed specifications from missing technical data, and provides practical guidance for evaluating this amplifier. It does not infer substitute pinouts or claim drop-in compatibility without manufacturer or web evidence.

RFQ İletişim
IRS2053MTRPBF 3-Ch 10-15V 6.2W Class D Driver | Infineon
IRS2053MTRPBF

IRS2053MTRPBF 3-Ch 10-15V 6.2W Class D Driver | Infineon

The Infineon IRS2053MTRPBF is a three-channel, high-performance Class D audio amplifier driver with integrated PWM modulators and protection, designed for a 10 V to 15 V supply and a 48-pin MLPQ (7 x 7 mm) package. The verified data identifies it as a 3-channel device associated with 6.2 W output and 60 dB gain, making it suitable for external-MOSFET automotive audio power stages. Its 0.50 mm package pitch supports compact layouts, while its -40 °C to 125 °C operating range addresses harsh automotive environments. The device is RoHS compliant according to the provided source. A Class D audio driver is a controller or gate-drive device that uses pulse-width modulation to drive external power MOSFETs in an audio half-bridge or full-bridge output stage. Unlike a conventional linear audio amplifier, the switching output stage can deliver audio with lower power dissipation than a comparable linear stage, although EMI filtering and careful layout remain important. The IRS2053 integrates three channels so a complete three-channel amplifier can be formed with external MOSFETs and passive components. Key verified features include three audio channels, a 10 V to 15 V supply range, 6.2 W output capability in the cited series description, 60 dB gain, a 48-MLPQ package measuring 7 x 7 mm, and 0.50 mm pitch. The package also has an exposed pad according to the supplied product-page description. The -40 °C to 125 °C temperature range supports automotive and industrial audio systems, while RoHS compliance supports regulated manufacturing and product-environment requirements. The IRS2053 uses floating analog inputs and a protection-control interface intended for external MOSFET half-bridge stages. In implementation, the three PWM outputs drive external power devices, while input conditioning, gate resistors, supply decoupling, output filtering, and protection components complete the power stage. Exact output power, modulation details, pin names, current limits, and timing values were not included in the provided verified data and must be confirmed in the manufacturer datasheet before layout or production use. Typical applications include automotive head units, three-channel infotainment systems, seat or console audio, and compact external Class D power modules. A three-channel arrangement can support front left, front right, and a center, subwoofer, or rear channel, depending on the amplifier architecture. The 10 V to 15 V supply range is suitable for automotive battery-derived rails after suitable regulation and filtering, but the exact automotive transient and operating requirements are not provided here. Designers should follow the manufacturer datasheet for exposed-pad thermal design, input filtering, power-supply decoupling, MOSFET selection, gate-loop layout, EMI control, and protection configuration. Because the provided data does not include complete pin-level definitions or verified electrical limits, no pin-level substitute should be assumed merely because it uses a nominally similar package.

RFQ İletişim