INA250A1PW - 36V Bidirectional Current-Sense Amplifier | TI
MPN: INA250A1PW ✓ AktifINA250A1PW Genel Bakış
A current-sense amplifier is a specialized instrumentation amplifier that converts the voltage across a current-sensing resistor into a proportional, low-level output voltage. The INA250 belongs to the current-sense amplifier hierarchy, where it supports precision measurement, power monitoring, motor control, industrial instrumentation, and protection systems. Its integrated shunt also reduces board area compared with a discrete shunt-resistor implementation.
The device provides bidirectional measurement through an externally applied reference voltage. Positive current can move the output above the reference level, while negative current moves it below that level. This arrangement allows a unidirectional amplifier output to represent both load directions and supports applications that need absolute-value or signed-current information. The 0 V to 36 V common-mode range covers many industrial, automotive-adjacent, power-supply, and motor-system rails.
The INA250A1PW uses the A1 gain option, which provides 20 V/V voltage gain. Its voltage-output architecture simplifies connection to analog-to-digital converters, comparators, controllers, and monitoring systems. Because the sensing element is integrated, PCB design must preserve the defined current path and provide adequate copper width and thermal capacity for the intended current level. The TSSOP package is a surface-mount package in the TSSOP-16 family.
Typical applications include high-side power-supply monitoring, bidirectional motor-current measurement, industrial control systems, battery current sensing, solenoid monitoring, and electronic protection. In these systems, the amplifier reconstructs a current-proportional voltage that can be digitized or compared with a threshold. System calibration should account for the selected gain, reference voltage, ADC resolution, and the measurement bandwidth required by the load.
Design attention should focus on Kelvin routing for the reference connection, filtering around the output when the measured waveform contains high-frequency noise, and thermal verification at maximum continuous current. The integrated shunt is convenient, but PCB copper, vias, pads, and connector geometry can limit practical current and increase temperature rise. Use the manufacturer pin-description table when assigning PCB tracks and the device data sheet for the complete recommended layout.
This page combines the manufacturer device description, package and operating information, practical application guidance, replacement criteria, and engineering-oriented design notes. These resources help engineers evaluate the INA250A1PW beyond a basic distributor listing while keeping pin compatibility and measurement accuracy at the center of the selection process.
Drop-in alternatifler için INA250A1PW — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu ürüne yer değiştirme seçenekleri mevcut değil.
Alternatifleri Talep EdinINA250A1PW Maksimum Değerlendirmeler & Elektriksel Özellikler
| Device Type | Bidirectional precision current-sense amplifier |
| Integrated Current-Shunt Resistor | Yes |
| Common-Mode Voltage Range | 0 V to 36 V |
| Maximum Common-Mode Voltage | 36 V |
| Çıkış Türü | Voltage output |
| Current Measurement Direction | Bidirectional |
| Gain Option | A1, 20 V/V |
| Referans Gerilimi | Externally applied |
| Paket | 16-pin TSSOP (PW) |
| İşletim Sıcaklığı Aralığı | -40 °C to +125 °C |
| Montaj Türü | Surface mount |
INA250A1PW 16-pin tssop (pw) Pin Yapısı Kılavuzu
INA250A1PW (16-pin tssop (pw) paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: INA250A1PW.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
INA250A1PW için uygundur 6 uygulamas: High-Side Power-Supply Monitoring, Bidirectional DC Motor Control, Industrial Load Monitoring, Battery Current Sensing, Solenoid and Actuator Feedback, Overcurrent Protection.
High-Side Power-Supply Monitoring
The INA250A1PW suits high-side power-supply monitoring because its integrated shunt measures current while the sensed rail can operate from 0 V to 36 V independently of the amplifier supply. Its 20 V/V gain converts bidirectional current into an analog voltage around an applied reference. Place the device in the positive or negative conductor, route the full load current through its defined pins, and connect the output to an ADC or threshold comparator. Copper width, via count, and thermal rise determine whether the layout supports the required continuous current.
Önerilen
Bidirectional DC Motor Control
The INA250A1PW provides signed motor-current feedback for closed-loop DC motor controllers. Its bidirectional operation allows an external reference to center the output so positive and negative current occupy opposite sides of that reference, while the 0 V to 36 V common-mode range covers many low-voltage motor buses. The 20 V/V gain establishes the current-to-voltage scale used by the controller. Designers should protect the control path from motor-edge transients, filter noise according to control-loop bandwidth, and verify that copper and thermal conditions remain acceptable at peak motor current.
Önerilen
Industrial Load Monitoring
The INA250A1PW is appropriate for industrial loads where signed current, compactness, and a wide sensed-voltage range are important. Its integrated shunt removes the footprint and tolerance-management burden of a discrete precision shunt, while the 20 V/V A1 gain provides usable scaling for moderate current ranges. A controller can monitor the analog output continuously or compare it against protection thresholds. Environmental qualification should be checked against the exact assembly requirements, and the PCB must maintain the specified current path without sharing narrow copper sections with sensitive measurement returns.
Önerilen
Battery Current Sensing
The INA250A1PW can monitor current in battery-powered equipment when the common-mode voltage stays within its 0 V to 36 V range. Bidirectional sensing is useful for systems that need charge and discharge current information, while the integrated shunt simplifies the analog front end. Connect the output to an ADC channel and use the external reference to establish the zero-current level. Before selection, calculate the maximum sense voltage at peak current, confirm the available amplifier supply range, and ensure the PCB current path remains within the device's intended operating conditions.
Önerilen
Solenoid and Actuator Feedback
The INA250A1PW can report current through a solenoid or actuator when the driven conductor is within the 0 V to 36 V common-mode range. The integrated sensing element provides a compact way to detect blocked motion, overload, or an open load without adding a discrete shunt. Its bidirectional capability can also distinguish current reversal in some actuator arrangements. Keep the analog output bandwidth consistent with the diagnostic response time, and place protection and filtering so switching edges do not dominate the measurement or upset an ADC input.
Önerilen
Overcurrent Protection
The INA250A1PW supports overcurrent detection by translating conductor current into a voltage that can be compared with a hardware threshold. Because the A1 version has 20 V/V gain, protection thresholds should be calculated from the actual output swing, reference voltage, and selected current limit rather than copied from another gain option. The integrated shunt also helps preserve measurement consistency across assembly. Validate tolerance at the temperature extremes, account for response delay during a short circuit, and ensure the current-carrying PCB path does not become the weakest element in the protection system.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: INA250A1PW — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Do not treat another INA250 gain option as an automatic drop-in substitute. INA250A2PW, INA250A3PW, and INA250A4PW increase the gain to 50, 100, and 200 V/V, respectively, requiring changes to output-range calculations, thresholds, software scaling, and possibly protection behavior. INA240-family devices support current measurement but use an external shunt, so they are not pin-compatible functional substitutes for the integrated INA250 architecture. Before placing a part, confirm the exact gain code, supply range, common-mode voltage, package, pin configuration, thermal conditions, and current-path layout.
Ana Farklılayıcılar
- Integrated precision shunt simplifies the sensing element (karşılaştırma:INA240A1PW)
- Wide common-mode operating range (karşılaştırma:INA250A2PW)
- Lower gain preserves measurement headroom for moderate currents (karşılaştırma:INA250A4PW)
Tasarım Notları
Use the manufacturer pin-description table to identify the current-carrying pins and preserve the specified copper path around the integrated shunt. Estimate: for a 1 A continuous current, the PCB copper, vias, pads, and package connections all contribute resistance and temperature rise, so the layout should be sized for the intended current rather than only the nominal signal connection. Keep the current path physically separate from sensitive analog routing to reduce unintended voltage offsets.
Route the reference and output connections as short analog traces, with their return path referenced to the device ground. The external reference defines the zero-current output level in bidirectional measurements, so excessive reference impedance can create offset or noise that appears directly on the measured-current signal. If the output connects to an ADC, select the input range for the 20 V/V gain and add filtering only after determining the required control or diagnostic bandwidth.
Verify continuous-current capability at the highest ambient temperature rather than relying only on nominal output range. Estimate: resistor power is calculated as P = I²R, and junction temperature depends on the package dissipation and PCB thermal resistance. The integrated shunt eliminates a discrete resistor but does not eliminate heat generated in the current path. Check connector pads, copper width, via count, and exposed thermal features against the maximum operating current and temperature rise.
Do not substitute another INA250 gain option as an electrically equivalent replacement. The A1 gain is 20 V/V, while the A2, A3, and A4 options provide progressively higher gain; changing gain changes output scaling, signal-to-noise requirements, and threshold calculations. Also verify that the common-mode voltage remains between 0 V and 36 V and that the separate amplifier supply stays within the manufacturer-specified operating range.
Uyumluluk Bilgisi
The identified technical pages do not provide explicit compliance statements for the exact ordering code, so each unconfirmed field is marked unknown. AEC-Q100 is not applicable because the device is an instrumentation amplifier rather than an automotive-qualified component.