Ürünler (44.000+)

MAX3387EEUG+T - 3V RS-232 Transceiver | Analog Devices
MAX3387EEUG+T

MAX3387EEUG+T - 3V RS-232 Transceiver | Analog Devices

The Analog Devices MAX3387EEUG+T is a 3V-powered RS-232 communications interface IC with three transmitters and three receivers, 250kbps data-rate capability, and enhanced electrostatic-discharge protection. It is packaged in a 24-pin TSSOP and can operate from a 3V to 5.5V supply. An RS-232 transceiver is a semiconductor interface that converts logic-level signals into RS-232 voltage levels and converts received RS-232 signals back into digital logic levels. The MAX3387E belongs to the interface IC hierarchy, where it bridges a host controller and external data-terminal equipment through EIA/TIA-232 links. Its dual charge-pump design supports true RS-232 operation from a low-voltage supply without a separate negative supply rail. The device provides three driver channels and three receiver channels, allowing two RS-232 ports or several individual data paths to be implemented in one package. A proprietary low-dropout transmitter output stage enables operation from supplies up to 5.5V while maintaining compliant output levels. The manufacturer also identifies enhanced ESD protection, with the product listing specifying 15kV protection. At data rates up to 250kbps, the MAX3387EEUG+T is appropriate for data links that require more throughput than a conventional low-speed serial port. Its internal charge pumps require four 0.1uF capacitors for operation from 3.3V. This compact approach eliminates the external negative-voltage supply circuitry commonly associated with older RS-232 implementations, reducing board area and simplifying system power design. Typical applications include industrial control terminals, data-acquisition equipment, point-of-sale terminals, configuration interfaces, portable diagnostic equipment, and embedded serial adapters. Multiple driver and receiver channels also suit designs that combine console, firmware-update, and peripheral-control links while limiting the number of interface ICs on the board. PCB design should keep the charge-pump capacitors close to their associated pins and provide adequate return paths for high-speed transitions. Designers should also distinguish powered logic-side signals from externally accessible RS-232 lines, route cables to reduce ESD exposure, and verify signal polarity and logic levels on every connected channel before production release. This page combines the manufacturer interface description with verified ordering information, a focused drop-in cross-reference, and practical implementation guidance. It is intended to help engineers identify the correct package variant, compare compatible devices, and implement a compact, low-power RS-232 interface without overlooking supply, ESD, or signal-integrity constraints.

RFQ İletişim
MAX3388ECUG+ - 2.5V 460kbps RS-232 Transceiver | Maxim
MAX3388ECUG+

MAX3388ECUG+ - 2.5V 460kbps RS-232 Transceiver | Maxim

The Maxim Integrated MAX3388ECUG+ is a 3-driver/2-receiver RS-232 transceiver designed for 2.5V-powered communications equipment. Rated for data rates up to 460kbps and enhanced electrostatic-discharge protection up to 15kV, the device is housed in a 24-pin TSSOP package. It implements a full RS-232 interface for portable and embedded systems that require bidirectional serial communication. An RS-232 transceiver is an interface integrated circuit that converts between complementary TTL/CMOS logic levels and the bipolar voltage levels used by RS-232 equipment. The MAX3388ECUG+ sits within the interface IC hierarchy as an EIA/TIA-232 communications transceiver, combining line drivers and receivers in one package. Its 2.5V supply operation is particularly useful for reducing the power burden in battery-powered phones, personal digital assistants, and other mobile equipment. The principal features include three transmit drivers, two receive inputs, operation from a single 2.5V supply, support for data rates as high as 460kbps, and enhanced ESD protection up to 15kV. These characteristics make the device suitable for portable equipment that must communicate with RS-232 peripherals while preserving a compact, low-voltage power architecture. The device's multi-driver arrangement allows several unidirectional RS-232 outputs alongside two receive channels, enabling asymmetric links such as command, control, status, and diagnostic paths. Its 24-pin TSSOP package provides a conventional surface-mount footprint that can simplify board layout relative to discrete driver and receiver implementations. Low-voltage operation also allows the IC to share a compact portable power rail without requiring a separate 5V interface supply. Typical applications include serial adapters for personal digital assistants, communication ports in cellular telephones, data acquisition equipment, industrial controllers, and portable test instruments. It is particularly appropriate where an equipment designer needs a compact EIA/TIA-232 interface, multiple logic-level outputs, receive inputs, and stronger ESD tolerance on externally accessible serial lines. When laying out a design, keep the transceiver's logic-side traces away from the exposed RS-232 connector and route driver outputs as short, direct connections to the interface pins. Confirm the connector's signal polarity and the logic-level relationship of the connected UART before using each driver and receiver, because the RS-232 electrical standard is not directly compatible with ordinary CMOS signals. This page combines the device's interface functions, RS-232 operating characteristics, verified package information, sourcing guidance, and application-focused design guidance to support faster component selection and implementation. For a replacement, verify the exact suffix, pin assignment, electrical ratings, and system-level RS-232 polarity before production release.

RFQ İletişim
MAX3388ECUG+T - 2.5V 460kbps RS-232 Transceiver | Analog Devices
MAX3388ECUG+T

MAX3388ECUG+T - 2.5V 460kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3388ECUG+T is a 2.5V-powered RS-232 transceiver with three drivers, two receivers, 460kbps data-rate capability, and enhanced 15kV electrostatic-discharge protection in a 24-TSSOP package. It is designed for portable systems that require a low-voltage, low-power communications interface. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and an RS-232 link. The MAX3388E family implements the electrical drivers and receivers required by EIA/TIA-232, also associated with V.28 and V.24 communications interfaces. Within the electronic-component hierarchy, it is a transceiver, interface IC, communications semiconductor, and low-voltage serial-interface device. Three RS-232 drivers support multiple outbound channels, while two receivers support two inbound channels. The 2.5V supply allows the device to operate from a low-voltage system rail without requiring a conventional 5V RS-232 supply. Its 460kbps maximum data rate makes it suitable for equipment whose serial links must transfer commands, configuration data, status information, or short data packets quickly. Enhanced electrostatic-discharge protection rated to 15kV is a major feature for connectors that can be touched during installation or connected to external cables. The protection is especially relevant to PDAs, mobile equipment, and industrial control systems where an RS-232 port may be exposed to electrostatic discharge. The manufacturer describes the MAX3388E and MAX3389E as low-power, high-data-rate communications interfaces with enhanced ESD protection. Typical uses include personal digital assistants, cellular phones, point-of-sale equipment, data acquisition units, industrial controllers, and service interfaces. The three-driver, two-receiver arrangement suits asymmetric links in which a controller sends commands to multiple peripherals while receiving responses from up to two devices. A system using fewer channels can disable unused drivers and receivers according to the device interface guidance. Designers should account for RS-232 level translation at the connector, protect the supply rail, and verify that signal rates and cable characteristics suit the intended link. Decoupling capacitors should be placed close to the supply and ground pins, while external driver and receiver networks should follow the manufacturer application guidance. The 24-TSSOP package also requires a PCB footprint consistent with its 0.65mm pitch. This product page combines manufacturer-interface details, package identification, ESD and data-rate specifications, drop-in alternatives, application guidance, and PCB-focused design considerations to support component selection and implementation. It is intended to help engineers evaluate electrical compatibility and make a board-level replacement decision without relying on family-level descriptions alone.

RFQ İletişim
MAX3388EEUG+ - 2.5V ESD-Protected RS-232 | Maxim
MAX3388EEUG+

MAX3388EEUG+ - 2.5V ESD-Protected RS-232 | Maxim

The Maxim Integrated MAX3388EEUG+ is a 2.5V-powered, ±15kV ESD-protected RS-232 interface transceiver with three transmitters and two receivers in a 24-pin TSSOP package. It combines three driver channels and two receiver channels on one device, making it suitable for compact equipment that needs bidirectional serial communication but does not require the same number of transmit and receive lines. An RS-232 transceiver is a semiconductor interface device that converts logic-level signals into RS-232 line levels and converts incoming RS-232 signals back into CMOS-compatible logic. The MAX3388EEUG+ supports EIA/TIA-232 and V.28/V.24 communications interfaces. Its low 2.5V supply design is particularly useful for portable equipment, personal digital assistants, and cellular-phone systems where power consumption and circuit area are important constraints. The three transmitter and two receiver arrangement gives the device a 3/2 channel configuration. Additional standout characteristics include ±15kV ESD protection and operation from a 2.5V supply. These features help protect the interface pins when cables are connected, removed, or exposed to electrostatic discharge during handling. The MAX3388E family is also identified as providing high data-rate capability and low power requirements. The 24-TSSOP package provides a surface-mount implementation with gull-wing terminals and a rectangular body. The industrial temperature grade makes the MAX3388EEUG+ appropriate for equipment operating across an industrial environment. Its three transmitters also allow a single package to support multiple outgoing RS-232 lines, reducing the number of interface components required on a board. Typical applications include handheld and portable communication equipment, personal digital assistants, cellular-phone accessories, point-of-sale terminals, diagnostic equipment, and embedded serial-port systems. The two receiver channels can support two incoming signals while the three transmitter channels serve outbound links or status and control lines. Designers should place required charge-pump and interface capacitors according to the manufacturer application circuit, maintain the specified supply range, and provide direct protection and layout measures for exposed cable connectors. The 24-pin TSSOP footprint is also sensitive to assembly and soldering practices, so the recommended land pattern and reflow profile should be followed. This page organizes the RS-232 channel configuration, supply voltage, ESD rating, package information, drop-in replacement analysis, comparison parameters, and practical interface-layout guidance into one engineering-focused resource for component selection and PCB design.

RFQ İletişim
MAX3388EEUG+T - 2.5V ESD-Protected RS-232 Transceiver | Maxim
MAX3388EEUG+T

MAX3388EEUG+T - 2.5V ESD-Protected RS-232 Transceiver | Maxim

The Maxim Integrated MAX3388EEUG+T is a 2.5V-powered, ±15kV ESD-protected RS-232 transceiver designed for portable data and communications equipment. The device combines three drivers and two receivers in a 24-TSSOP package, operates from a single 2.5V supply, and supports data rates up to 460kbps. Its combination of low power requirements, high data-rate capability, and enhanced electrostatic-discharge protection makes it appropriate for RS-232 links in PDAs, cellular phones, and other compact portable systems. An RS-232 transceiver is an interface IC that converts between digital logic-level signals and RS-232 line-level signals. The transmitter section drives logic-level data onto a serial interface, while the receiver section converts incoming RS-232 signals back into logic-compatible data. As a 3/2 transceiver, the MAX3388EEUG+T provides three transmit channels and two receive channels in one package, reducing component count and simplifying portable serial-interface designs. The main advantages of this MAX3388E-family device include its low 2.5V operating supply, data-rate capability of 460kbps, and ±15kV ESD protection. The low supply voltage supports designs in which conserving battery energy and reducing overall system voltage are priorities. ESD protection is particularly valuable in handheld equipment because exposed serial connectors are susceptible to electrostatic discharge during use, handling, and connection to external accessories. The MAX3388EEUG+T belongs to the MAX3388E and MAX3389E interface family, which is designed around EIA/TIA-232 and V.28/V.24 communications interfaces. Both families share a low-power 2.5V architecture, high data-rate operation, and enhanced ESD protection. The MAX3388E provides two receivers, making it appropriate for designs that need more driver channels than receiver channels. Typical uses include RS-232 connections in PDAs and cellular phones, portable data acquisition equipment, and embedded systems that exchange serial data with accessories or service equipment. In these applications, the device can bridge a low-voltage controller to an external RS-232 port while maintaining a compact 24-pin surface-mount footprint. Board designers should still provide suitable connector protection and route the interface according to the manufacturer's application guidance. A key design consideration is the distinction between the low-voltage logic side and the RS-232 side. Decoupling, grounding, and connector placement can affect signal integrity and ESD performance even when the IC itself includes internal protection. Use the pin-description and application-circuit information in the manufacturer datasheet when assigning input, output, enable, ground, and supply connections. This product page combines exact package and interface information with practical drop-in cross-reference options, application guidance, and design considerations. It supports faster component identification while preserving the distinction between verified electrical facts and engineering guidance that still requires circuit-level validation.

RFQ İletişim
MAX3389ECUG+ - 2.5V 3/2 RS-232 Transceiver | ADI
MAX3389ECUG+

MAX3389ECUG+ - 2.5V 3/2 RS-232 Transceiver | ADI

Analog Devices MAX3389ECUG+ is a 3-driver, 2-receiver RS-232 transceiver designed for low-voltage serial-interface systems. It operates from a 2.5V supply, supports the EIA/TIA-232 and V.28/V.24 communication standards, provides ±15kV ESD protection on its external interface pins, and is packaged in a 24-pin TSSOP. The device targets portable and mobile equipment requiring a compact, low-power RS-232 interface. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a cable-based RS-232 link. The MAX3389ECUG+ combines three transmit channels with two receive channels in one package. This mixed 3/2 configuration allows one controller to command three external targets while receiving status or data from two of them, reducing the number of separate interface components required in portable equipment. The primary electrical features are the 2.5V operating supply, a specified 2.35V to 3V transceiver supply range, and ±15kV ESD protection. These characteristics make the device suitable for systems in which connector exposure, limited battery energy, and restricted board area are important design constraints. The enhanced ESD protection helps improve interface robustness when users connect external cables to personal digital assistants, mobile phones, and other handheld communications products. The MAX3389 family implements the electrical signaling required by EIA/TIA-232 and V.28/V.24 interfaces. Driver channels convert TTL-compatible command signals into RS-232 levels, while receiver channels recover RS-232 data as logic-level signals. The integrated multi-channel arrangement also reduces the number of package outlines and PCB land patterns that a design team otherwise needs to manage for several independent serial ports. Typical uses include personal digital assistant connectivity, mobile phone accessories, handheld test equipment, point-of-sale terminals, and compact industrial controllers. The low 2.5V supply requirement allows the interface to operate alongside low-voltage logic, while the TSSOP-24 package supports compact board layouts. Product qualification, ordering, and lifecycle requests can be handled through the Request a Quote form on this page. The primary design consideration is external-signal handling. Although the device has enhanced ESD protection, the board still needs a suitable return path, controlled cable routing, and connector placement that minimizes ESD exposure. Power and signal integrity should be evaluated together because the RS-232 drivers and receivers operate at a higher voltage domain than many modern low-voltage host controllers. This page combines the identified electrical ratings, package information, application context, comparison parameters, and practical design guidance into one engineering reference. It also distinguishes exact drop-in candidates from related interface families and highlights which characteristics must still be confirmed in the manufacturer datasheet before a substitution is released to production.

RFQ İletişim
MAX3389ECUG+T - 2.5V RS-232 Transceiver | Analog Devices
MAX3389ECUG+T

MAX3389ECUG+T - 2.5V RS-232 Transceiver | Analog Devices

The Analog Devices MAX3389ECUG+T is a 2.5V-powered, 3/2 RS-232 transceiver with two drivers, two receivers, 15kV ESD protection, and a 24-pin TSSOP package. Designed for low-power portable equipment, it combines an EIA/TIA-232 interface with enhanced electrostatic-discharge protection. Its 2.5V supply operation suits PDAs, cellular phones, data terminals, and other compact systems where both circuit-board area and operating power are constrained. An RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and an RS-232 link. A driver converts TTL or CMOS logic into RS-232 levels, while a receiver converts incoming RS-232 signals back into logic levels. As a member of the voltage-regulator and power-management ecosystem, this interface IC connects low-voltage digital circuitry to the voltage and polarity characteristics of an RS-232 communications port. The MAX3389ECUG+T provides 15kV ESD protection, a 2.5V supply, low power requirements, and high data-rate capability. Its three-driver, two-receiver configuration supports one communications channel plus one additional transmit function, making it practical for devices that need more than one RS-232 output but fewer than three active receivers. The integrated protection reduces the need for separate external protection networks on exposed connector-facing pins. The MAX3389E belongs to the MAX3388E and MAX3389E family of 2.5V-powered EIA/TIA-232 and V.28/V.24 communications interfaces. The MAX3389E configuration contains two drivers and two receivers. Because the interface operates from a low supply voltage, careful consideration of input levels, bypass capacitors, connector exposure, and grounding remains necessary when connecting it to legacy RS-232 equipment. Typical uses include RS-232 ports in PDAs, cellular phones, portable instruments, point-of-sale terminals, and embedded communications equipment. The part is especially relevant where a 5V interface would add unnecessary power, where a 24-pin TSSOP footprint fits an existing layout, or where exposed RS-232 lines require stronger ESD protection. It can also support multiple wired communications functions when a system does not need every driver and receiver active simultaneously. Place the MAX3389ECUG+T close to the RS-232 connector when practical, route each driver and receiver trace away from sensitive analog circuitry, and connect the interface ground to the system ground according to the board-level return-current plan. The 2.5V supply should be bypassed locally, while any external protection still needed for severe industrial transients should be selected for the connector environment rather than assumed to be covered by the IC. This product data combines the MAX3389ECUG+T configuration, directly documented interface characteristics, verified package information, and a validated same-footprint replacement path. It also adds application-focused design guidance intended to make RS-232 integration more reliable in portable and embedded systems.

RFQ İletişim
MAX338CEE+ - 8:1 Low-Leakage CMOS Analog Mux | Analog Devices
MAX338CEE+

MAX338CEE+ - 8:1 Low-Leakage CMOS Analog Mux | Analog Devices

The Analog Devices MAX338CEE+ is an 8-channel, low-leakage CMOS analog multiplexer with a 1 Circuit 8:1 configuration, 400 ohm on-resistance, and a 16-QSOP package. According to the manufacturer product data, the device connects one of eight inputs to a common output, making it suitable for routing external analog signals in test, measurement, control, and communication systems. The verified listing identifies a single +4.5 V to +30 V supply or dual supplies of ±4.5 V to ±20 V. An analog multiplexer is an analog switch device that selects one signal path among multiple inputs and connects it to a shared output. The MAX338 family is positioned as a low-leakage CMOS analog multiplexer family, with the MAX338 providing eight channels and the related MAX339 providing dual four-channel operation. This hierarchy places the part within analog switches, multiplexers, interface ICs, and broader signal-routing systems. The verified MAX338CEE+ data specifies 400 ohm on-resistance and an 8:1 topology. Analog Devices identifies the MAX338 and MAX339 as pin-compatible upgrades for the industry-standard DG508A and DG509A families. The low-leakage characteristic is useful when source impedance is high, because leakage through an inactive channel can otherwise create measurement errors or interfere with small-signal nodes. The device also supports both single-supply and dual-supply operation, allowing integration into systems with different reference and bias arrangements. Typical uses include data acquisition, automated test equipment, sensor multiplexing, analog signal routing, sample-and-hold systems, and industrial control interfaces. The 8:1 arrangement reduces the number of physical connections required when a controller must inspect several analog sources through one downstream converter or measurement channel. Designers should verify signal amplitude, supply polarity, control logic, switching timing, and package footprint against their particular system before production use. A key design consideration is keeping unused analog inputs, control pins, and supply rails within the manufacturer's specified operating limits. PCB routing should minimize trace resistance and capacitance around high-impedance signal nodes, while grounding and decoupling should follow the datasheet recommendations. This page summarizes verified product, distributor, and manufacturer information; application suitability still depends on the complete electrical specification set.

RFQ İletişim
MAX338CPE+ - 8:1 CMOS Analog Multiplexer | Analog Devices
MAX338CPE+

MAX338CPE+ - 8:1 CMOS Analog Multiplexer | Analog Devices

The Analog Devices MAX338CPE+ is a single 8:1 CMOS analog multiplexer with 16-pin PDIP packaging, a 400 ohm on-resistance listing, and operation from a single 4.5 V to 30 V supply. It can also operate from dual supplies of ±4.5 V to ±20 V, making it suitable for instrumentation, industrial signal-routing, and test systems that require routing one of eight analog inputs to a common output. The chipdig listing also identifies the device as an 8-channel, low-leakage CMOS analog multiplexer with a 650 ohm resistance specification, so engineers should verify the applicable on-resistance condition against the manufacturer datasheet for their exact supply and temperature configuration. An analog multiplexer is a semiconductor switch that connects one selected input channel to a shared output. The MAX338CPE+ belongs to the CMOS analog switch and multiplexer hierarchy, where low-leakage CMOS construction supports high-impedance measurement circuits. Its 8:1 configuration reduces the number of physical input connections required when a controller must inspect several voltage, sensor, or diagnostic signals sequentially. The common output can then feed an ADC, measurement instrument, amplifier, or further signal-processing stage. Key features include eight selectable analog inputs, a single-ended common output, and a single 16-pin PDIP package. According to the Analog Devices MAX338 product page, the MAX338 and MAX339 devices are improved multiplexers that are pin-compatible upgrades for the industry-standard DG508A and DG509A families. The MAX338 family also supports both single and dual power-supply arrangements. These features distinguish it from multiplexer products that require one supply rail only or provide a different channel-to-pin arrangement. The MAX338CPE+ is a monolithic CMOS device intended to route low-frequency analog signals. Its channel count, supply range, and legacy DIP footprint are particularly useful when creating test fixtures, sensor interfaces, process-control equipment, or diagnostic systems that need to remain compatible with an existing 16-pin design. Because the common output carries the selected channel, the source impedance, signal amplitude, settling behavior, and downstream input range remain important system-level considerations. Typical uses include eight-way sensor selection, automated test equipment, industrial control signal routing, laboratory measurement systems, and instrumentation with multiple analog sources. The same-package DG508A and DG509A reference points are also useful when evaluating a design that was originally built around those established multiplexers. The MAX339 provides a related 4:1 dual-channel function rather than the MAX338's single 8:1 arrangement. When laying out the circuit, place the multiplexer close to the source and destination analog paths to minimize parasitic capacitance and resistance. Keep high-impedance traces short, provide a stable supply reference, and avoid excessive loading on the common output. Engineers should also confirm the exact channel pin assignments, control truth table, electrical limits, and operating-temperature grades in the manufacturer datasheet before treating the part as a production drop-in replacement. This page consolidates verified manufacturer and distributor information, supply configurations, package details, drop-in references, and practical selection guidance. It distinguishes documented pin-compatible alternatives from broader functional equivalents so procurement and engineering decisions can be made without confusing a multiplexer upgrade with a merely similar switch.

RFQ İletişim
MAX338CSE+ - 8-Channel CMOS Analog Multiplexer | Maxim
MAX338CSE+

MAX338CSE+ - 8-Channel CMOS Analog Multiplexer | Maxim

The Maxim Integrated (now part of Analog Devices) MAX338CSE+ is a monolithic CMOS 8:1 analog multiplexer (also configurable as a dual 4:1) housed in a 16-pin narrow-body SOIC (NSOIC) package. It is built to route one of eight single-ended analog inputs to a common output under control of a 3-bit binary address, with on-resistance (RON) of 400 ohm typical over the full signal range. What is an analog multiplexer? An analog multiplexer (MUX) is a semiconductor switch that selects one of N analog input channels and routes it to a single output line, allowing a microcontroller or ADC to "scan" many sensors or signals through a single high-performance analog front-end. Multiplexers belong to the larger family of analog switches and are foundational building blocks in data acquisition, instrumentation, audio routing, and test equipment. The MAX338 operates from a single +4.5V to +30V supply (or dual ±4.5V to ±20V supplies), giving designers wide headroom for industrial 24V rails and ±15V instrumentation racks. Key features include low-leakage CMOS construction (typically < 1 nA at room temperature), break-before-make switching action that prevents momentary channel cross-connection, ESD protection on all logic and analog pins, and pin-compatibility with the industry-standard DG508A / DG509A, enabling direct drop-in upgrade to lower leakage. Logic inputs are TTL/CMOS compatible, simplifying interface to 3.3V and 5V microcontrollers. The MAX338 is fabricated on a low-leakage dielectric-isolation CMOS process that minimizes parasitic capacitance and channel-to-channel charge injection. Internal logic-level translation allows the digital inputs (A0, A1, A2, EN) to be driven directly from modern microcontrollers. The device is specified over the commercial 0C to +70C temperature range, making it well suited for indoor test equipment and laboratory instrumentation rather than industrial or automotive use; for extended temperature ranges see the MAX338E variant. Typical applications include data-acquisition front-ends scanning multiple thermocouples or analog sensors, audio signal routing in mixing consoles and broadcast equipment, automated test equipment (ATE) pin boards, instrumentation multiplexer and sample-and-hold front ends, industrial process control signal multiplexing, and medical patient-monitoring analog front ends. Designers choose it when they need more analog inputs than their ADC provides and require clean, low-leakage switching. When designing with this device, place 0.1uF decoupling capacitors close to V+ and V- (or GND for single-supply use) and keep analog traces short to minimize crosstalk. Ensure all unused digital and analog inputs are tied to a defined logic level (not left floating) to prevent channel-to-channel leakage paths. This page synthesizes distributor pricing, drop-in alternatives, application guidance, and pin-level design notes that complement the manufacturer datasheet.

RFQ İletişim
MAX338EEE+ - 8:1 Low-Leakage CMOS Multiplexer | Maxim Integrated
MAX338EEE+

MAX338EEE+ - 8:1 Low-Leakage CMOS Multiplexer | Maxim Integrated

The Maxim Integrated MAX338EEE+ is an 8:1 low-leakage CMOS analog multiplexer with 400 ohm on-resistance, supplied in a 16-QSOP surface-mount package. It connects one of eight inputs to a common output and operates from a single +4.5 V to +30 V supply or from dual ±4.5 V to ±20 V supplies. The MAX338 family also includes dual 4-channel configurations for designs requiring two independently selected signal paths. An analog multiplexer is a semiconductor switching network that routes one selected input to a shared output. The MAX338 belongs to the CMOS analog switch and multiplexer hierarchy, where low leakage is valuable when measuring weak, high-impedance signals or when unused channels must contribute little error to the measurement system. It also supports positive-only and split-supply analog systems, allowing the same switching architecture to serve instrumentation, test, measurement, and signal-routing equipment. Verified product information identifies one analog switch circuit, an 8:1 configuration, 400 ohm on-resistance, a 16-QSOP package, and low-leakage CMOS construction. The single-supply operating range is +4.5 V to +30 V, while dual-supply operation extends from ±4.5 V to ±20 V. These wide ranges permit use with legacy ±15 V analog circuits as well as modern single-rail systems. The EEE ordering code is associated with the industrial-grade 16-terminal surface-mount variant shown in distributor data. Because the MAX338 is a monolithic CMOS multiplexer, its internal channels share one common output. This architecture minimizes the number of external signal paths in a multi-source measurement design, although it does not provide simultaneous access to all eight channels. Selection should therefore be based on required channel count, acceptable on-resistance, leakage limit, supply topology, and the voltage and current levels present at each switched node. Detailed leakage, bandwidth, charge-injection, and switching-time figures were not supplied in the verified excerpts and must be taken from the manufacturer datasheet. Typical uses include automated test equipment, data-acquisition systems, sensor-signaling interfaces, process-control instrumentation, and laboratory measurement front ends. The device is particularly useful when many potential analog inputs must share one amplifier, converter, or data-acquisition channel. A suitable external circuit must also keep every input and output within the device's absolute maximum ratings during switching and fault conditions. Designers should verify control logic levels, input overvoltage tolerance, analog signal range, and break-before-make behavior against the full datasheet before layout release. Care should be taken around unused channels, signal-source impedance, and injected charge because low leakage alone does not guarantee low measurement error. Input filtering may be appropriate when fast transients or high-energy events are possible. This product record combines verified manufacturer and distributor information, explicit data-gap markers, same-family drop-in candidates, and practical selection guidance. It is intended to help engineers identify the correct 16-QSOP multiplexer while separating confirmed MAX338EEE+ attributes from parameters that still require direct datasheet verification.

RFQ İletişim
MAX338EEE+T - 8:1 CMOS Analog Multiplexer | Maxim Integrated
MAX338EEE+T

MAX338EEE+T - 8:1 CMOS Analog Multiplexer | Maxim Integrated

Maxim Integrated MAX338EEE+T is an 8:1 single-ended CMOS analog multiplexer with 400 ohm on-resistance, housed in a 16-pin SSOP package. It selects one of eight analog inputs and connects the selected input to a common output. The device operates from a single +4.5 V to +30 V supply or from dual supplies of ±4.5 V to ±20 V, making it suitable for both positive-rail and split-supply instrumentation. An analog multiplexer is an interface IC that routes multiple analog signals through one common connection. The MAX338 belongs to the CMOS analog switch family, combining an 8:1 multiplexer with low-leakage switching elements. This allows a measurement system, data-acquisition circuit, or industrial control board to reduce the number of dedicated signal paths while preserving accurate analog connectivity. The principal features include an 8:1 configuration, 400 ohm on-resistance, and 20 pA leakage. Its address and enable controls are TTL-compatible from +0.8 V to +2.4 V across the specified temperature and supply ranges. These characteristics make the device useful when a system must select among sensor outputs, measurement inputs, or multiplexed test points without using a separate connector for every channel. The MAX338 is fabricated using Maxim's 44 V silicon-gate process, supporting operation with relatively wide supply voltages. The manufacturer identifies the MAX338 and MAX339 as improved, pin-compatible upgrades for the industry-standard DG508A and DG509A. Related MAX328 and MAX329 devices provide lower leakage and charge injection but higher on-resistance, creating a useful trade-off between leakage, switching transients, and signal resistance. Typical applications include data-acquisition systems, automated test equipment, industrial process monitoring, medical instrumentation, and communication-interface boards. An eight-channel bank can route eight analog sources into one amplifier, comparator, or converter input, while complementary address and enable logic controls the selected path. The industrial temperature grade also supports equipment intended for factory, laboratory, and communications environments. PCB design should place input and output traces away from high-speed digital paths, provide a stable ground reference, and observe the supply and decoupling requirements in the manufacturer datasheet. Because the multiplexer contributes 400 ohm of series resistance and switching transients, the receiving amplifier should have sufficiently high input impedance and bandwidth. Fault conditions should also be checked with the device disabled so that unused inputs cannot create unintended loading or signal transitions. This product page combines manufacturer specifications, package information, functional context, replacement guidance, and application-oriented design guidance. It helps engineers evaluate the MAX338EEE+T against same-package family options while accounting for channel configuration, on-resistance, leakage, and control-interface compatibility.

RFQ İletişim
MAX338EPE+ - 8:1 400Ω Analog Multiplexer | Analog Devices
MAX338EPE+

MAX338EPE+ - 8:1 400Ω Analog Multiplexer | Analog Devices

The Analog Devices MAX338EPE+ is an 8:1 single-ended CMOS analog multiplexer with 400 Ω on-resistance, 16-PDIP package, and 3-bit binary address control. The device connects one of eight inputs to a common output, making it suitable for analog signal routing in instrumentation, test systems, data acquisition, and embedded control equipment. Verified distributor data identifies the MAX338EPE+ as a single-circuit IC switch, 8:1 multiplexer, 400 Ω switch, and 16-pin DIP package; the Analog Devices product page describes the MAX338 family as a monolithic CMOS analog multiplexer. An analog multiplexer is a switching semiconductor that routes multiple analog inputs to one shared signal path under digital control. The MAX338/MAX339 family belongs to the analog switch and mux hierarchy, where the MAX338 provides one 8-channel single-ended path and the MAX339 provides dual 4-channel operation. Reducing the number of external signal connections can simplify wiring, board space, and system architecture when several sensors or measurement nodes must be selected by a controller. Key verified characteristics include an 8:1 configuration, 400 Ω on-resistance, 16-PDIP mechanical package, industrial temperature grade, and through-hole mounting. The MAX338EPE+ uses a 3-bit binary address to select one of eight inputs according to the manufacturer description. The verified snippets do not provide complete electrical limits such as supply voltage, leakage current, bandwidth, switch capacitance, or logic thresholds, so those values must be checked against the official manufacturer datasheet before final design release. The MAX338 family is positioned for low-leakage CMOS analog multiplexing. This makes the device relevant where a controller must scan multiple analog sources while preserving a common signal-conditioning path. The common output can feed a downstream amplifier, ADC, comparator, or measurement front end, while the selected address determines which input reaches that shared node. The exact input signal range and allowable switching conditions depend on parameters not included in the verified search snippets. Typical uses include multimeter and bench-test input selection, sensor-channel scanning, industrial control interfaces, data-acquisition systems, and embedded measurement modules. The 16-PDIP package favors through-hole prototyping and repair rather than compact surface-mount production. Because the available evidence does not provide full timing, power, and absolute-maximum ratings, engineers should use the official MAX338 datasheet and validate signal levels, supply rails, leakage, settling behavior, and control timing in the intended system. A key design consideration is ensuring that the downstream circuit can tolerate the mux's on-resistance, leakage, and charge injection. Signal-chain errors become more significant when source impedance is high, source-to-source voltage differences are large, or measurement accuracy is dominated by leakage. Route the selected output with short traces, maintain a stable reference and supply arrangement, and account for control-signal timing before sampling the analog node. This page combines verified distributor listings, the Analog Devices family description, package information, and practical selection guidance for engineers evaluating the MAX338EPE+. Pricing shown here is a reference as of 2026-10-21 and should be confirmed with the seller before purchase.

RFQ İletişim
MAX338ESE+ - 8:1 Low-Leakage CMOS Analog Multiplexer | Maxim Integrated
MAX338ESE+

MAX338ESE+ - 8:1 Low-Leakage CMOS Analog Multiplexer | Maxim Integrated

The Maxim Integrated MAX338ESE+ is an 8-channel, low-leakage CMOS analog multiplexer packaged in a 16-pin narrow SOIC, with a maximum on-resistance of 400 ohm and a single-supply operating range of +4.5V to +30V (or dual supplies of +/-4.5V to +/-20V). The device is pin-compatible with the industry-standard DG508A and DG509A, and the ESE suffix denotes the extended temperature (-40C to +85C) 16-SOIC package. An analog multiplexer, or mux, is a semiconductor switch that routes one of several analog input channels to a shared output node under digital address control. It sits in the signal path between sensors, amplifiers and converters on one side and a single measurement or processing chain on the other. In the broader hierarchy, MAX338ESE+ belongs to the analog switch and multiplexer family, which in turn falls under interface ICs within integrated circuits. Reducing eight or sixteen analog wires down to one shared node is the core value proposition: fewer PCB traces, fewer connector pins, and a smaller multiplexing front end for data acquisition. Key features include a 400 ohm maximum on-resistance, low off-state leakage, and bidirectional analog channels, so the mux can be used as either a multiplexer or a demultiplexer. The device runs from a single +4.5V to +30V rail or from dual rails of +/-4.5V to +/-20V, which makes it suitable for both modern low-voltage instrumentation and legacy +/-15V or +/-12V analog test equipment. Fault-protected channel architecture improves robustness when inputs are over-driven or switched while signals are present. Internally the MAX338 uses CMOS transmission-gate switches driven by a 3-bit binary address for the 8-channel configuration, with the address decode and drive circuitry integrated on the same die. Because the channels are bidirectional, the same silicon supports demultiplexing applications where the single common node is driven and the eight channel nodes are the destinations. This symmetry is what allows one part number to cover both directions of analog routing. Typical applications include multi-channel data acquisition systems, automated test equipment, process-control instrumentation, multimeter and measurement front ends, battery and power-supply test systems, and data logger signal conditioning. Designers frequently use the MAX338 alongside RS-232 and RS-485 transceivers, parallel interface controllers, and precision amplifiers to build compact measurement instruments. The main design consideration is supply headroom and signal range: because the channels are bidirectional and the on-resistance is relatively high at 400 ohm, the device is best suited to high-impedance sources and precision measurement nodes rather than low-impedance power or current-carrying loads. Check the injected charge and off-state leakage against your accuracy budget. This page consolidates manufacturer documentation, distributor pricing and availability, pin-compatible drop-in alternatives, and practical layout guidance so engineers can evaluate a redesign or a second-source sourcing decision without pulling together five separate documents.

RFQ İletişim
MAX338ESE+T - 8:1 CMOS Analog Multiplexer | Analog Devices
MAX338ESE+T

MAX338ESE+T - 8:1 CMOS Analog Multiplexer | Analog Devices

Analog Devices MAX338ESE+T is an 8:1 CMOS analog multiplexer with 400 ohm on-state resistance, housed in a 16-SOIC package. The device operates from a single +4.5 V to +30 V supply or from dual supplies of ±4.5 V to ±20 V, and its TTL-compatible address and enable inputs support both 5 V and high-voltage control environments. An analog multiplexer is an analog switch that routes one of several input signals to a shared output. The MAX338 belongs to the broader hierarchy of CMOS analog switch, multiplexer, interface IC, and semiconductor devices. Its eight channels are selected by a 3-bit binary address, while an enable input provides control over the selected connection. The device can therefore operate as a multiplexer or serve as a demultiplexer when the direction of signal routing is reversed. The MAX338/MAX339 family uses Maxim's 44 V silicon-gate process. This process supports operation from a single +4.5 V to +30 V supply or from dual ±4.5 V to ±20 V supplies. All address and enable controls remain TTL-compatible over their specified ranges, with a +0.8 V to +2.4 V input threshold identified for the control inputs. These characteristics make the multiplexer suitable for systems that must route wide-range analog signals. The 400 ohm on-state resistance identifies the MAX338 as a low-leakage CMOS multiplexer option intended for precision signal routing rather than high-current power switching. Its eight-to-one configuration reduces the number of physical connections required when several measured or conditioned signals must reach one processing channel. The common output architecture can also simplify board routing when a controller selects among sensor, instrument, or test-point signals. Typical applications include automated test equipment, data-acquisition systems, instrumentation, industrial control, and measurement setups. In each case, the 3-bit address bus identifies the desired channel and the enable input controls whether the common output is connected. The part is particularly useful where one analog input must be presented to a shared amplifier, converter, or measurement circuit without duplicating that downstream circuitry. A key design consideration is that the MAX338 is not a power switch. Its 400 ohm on-state resistance contributes signal attenuation and, when driving a finite load, can introduce an interaction between switch resistance and downstream input impedance. Layout should keep analog traces short, maintain a stable return path, and avoid placing high-current switching nodes near the selected input channels. This page consolidates the manufacturer's supply-range information, package details, functional characteristics, verified alternatives, and practical routing guidance into an engineering-focused guide for selecting and implementing the MAX338ESE+T in high-voltage analog multiplexing systems.

RFQ İletişim
MAX338ETE+ - 8:1 400Ω Low-Leakage MUX | Maxim Integrated
MAX338ETE+

MAX338ETE+ - 8:1 400Ω Low-Leakage MUX | Maxim Integrated

The Maxim Integrated MAX338ETE+ is an 8:1 CMOS analog multiplexer with a 400 Ω on-resistance, low-leakage design, and a 16-pin TQFN package measuring 5 x 5 mm. According to the verified manufacturer product page, the MAX338 family is also described as an 8-channel or dual 4-channel low-leakage CMOS analog multiplexer. The device connects one of eight inputs to a common output using a 3-bit binary address, making it suitable for analog signal routing, measurement systems, instrumentation, and control equipment. An analog multiplexer, or analog mux, is an interface IC that routes one selected input channel to a shared output while blocking unselected channels. The MAX338 is a monolithic CMOS device intended for low-leakage signal-path applications. Its 8:1 configuration reduces the number of external signal lines when a system must select among multiple sensors, sources, or measurement channels. The 400 Ω specification is identified by the verified distributor listing, while additional electrical limits are not supplied in the retrieved data and are therefore not inferred here. The key verified feature set includes an 8:1 configuration, 400 Ω on-resistance, low-leakage operation, CMOS construction, and a 16-TQFN 5 x 5 mm package. The manufacturer describes the MAX338 family as connecting one of eight inputs to a common output through a 3-bit binary address. The single-pole, single-throw switching arrangement is represented by the 8:1 mux function, although detailed break-before-make and charge-injection values were not provided in the verified snippets. This part is useful when the system must share a downstream amplifier, ADC, DAC, or measurement block across several analog sources. It can help simplify routing in data-acquisition systems, sensor interfaces, automated test equipment, industrial controllers, and communication equipment. The low-leakage characteristic is particularly relevant when source impedance is high or when leakage can affect measurement accuracy, although the exact leakage limit should be confirmed in the manufacturer datasheet. The 16-TQFN package supports compact surface-mount layouts and requires careful PCB design around the exposed-pad and thermal requirements shown in the manufacturer documentation. A key design consideration is to verify signal voltage, supply voltage, input impedance, switching speed, and leakage against the complete MAX338 data sheet before production release. The verified distributor data confirms the part number and package, but does not provide a complete set of timing, current, or absolute-maximum ratings. This product page combines the verified manufacturer identification, distributor package data, pricing references, and application guidance. It also distinguishes confirmed parameters from values requiring datasheet confirmation, helping engineers make an informed sourcing decision without introducing unsupported specifications.

RFQ İletişim
MAX338ETE+T - 8:1 CMOS Analog Multiplexer | Analog Devices
MAX338ETE+T

MAX338ETE+T - 8:1 CMOS Analog Multiplexer | Analog Devices

Analog Devices MAX338ETE+T is a single 8:1 CMOS analog multiplexer with 400 ohm on-resistance, housed in a 16-TQFN package with a 5 x 5 mm footprint. It operates from a single +4.5V to +30V supply or from dual supplies of ±4.5V to ±20V. Its TTL-compatible address and enable inputs accept logic levels from +0.8V to +2.4V across the specified temperature range. An analog multiplexer is an analog switch that routes one of several input signals to a shared output. A single 8:1 multiplexer provides eight selectable signal paths while reducing the number of external connections required between a source circuit and a measuring or processing circuit. The MAX338 is designed for precision signal-routing requirements and is fabricated using Maxim's 44V silicon-gate process. The primary function is an 8:1 single-ended analog switch. Its specified 400 ohm on-resistance makes it suitable for routing moderate-impedance sensor, measurement, or control signals rather than high-current loads. TTL-compatible control inputs simplify connection to 5V CMOS and TTL control logic. Operation from either a single positive supply or dual supplies also supports systems that use positive-only or bipolar analog rails. The MAX338 family is fabricated on a 44V silicon-gate process, providing the voltage headroom needed for the specified operating ranges. The manufacturer describes the MAX338 as a low-leakage CMOS analog multiplexer. Its improved multiplexing performance is intended to address both leakage and charge-injection considerations when selecting among analog sources, although exact device-level values should be confirmed in the manufacturer datasheet. Typical applications include sensor-signal selection, data-acquisition front ends, instrumentation, industrial control, test and measurement equipment, and analog signal routing in systems operating from a single +5V rail or higher single-supply rails. The eight-to-one configuration is especially useful when a system must select among multiple analog inputs before conversion, amplification, comparison, or further signal conditioning. When designing around the MAX338ETE+T, verify the exact supply limits, control-logic states, analog signal range, switch configuration, and exposed-pad connection against the manufacturer datasheet. Place the device so its thermal pad can dissipate heat as intended, keep sensitive analog routing away from fast-switching nodes, and account for off-state leakage and channel charge injection in high-impedance precision circuits. This product page consolidates the MAX338ETE+T manufacturer specifications, verified product identifiers, source links, application guidance, design considerations, and qualified replacement information. It is structured to help engineers move from datasheet lookup to footprint-compatible sourcing without treating different package or electrical variants as interchangeable.

RFQ İletişim
MAX338MSE/PR3+ - 8:1 CMOS Multiplexer | Analog Devices
MAX338MSE/PR3+

MAX338MSE/PR3+ - 8:1 CMOS Multiplexer | Analog Devices

Analog Devices MAX338MSE/PR3+ is a single 8:1 CMOS analog multiplexer with 400 ohm on-resistance, a 3-bit binary address interface, and a 16-pin SOIC package. It connects one of eight inputs to a common output and can also operate as an eight-channel demultiplexer by reversing the signal-routing role. The low-leakage architecture is intended for precision analog-signal selection systems where minimizing off-state coupling is important. An analog multiplexer is a semiconductor switch that routes one of several physical input channels to a shared signal path. It belongs to the analog switch and multiplexer hierarchy, interface IC category, and broader signal-conditioning system. Unlike a digital multiplexer, its primary purpose is to preserve analog signal integrity while selecting a source for measurement, conversion, instrumentation, or communication circuitry. The MAX338 family provides eight selectable channels in the MAX338 configuration and uses address logic to determine which input reaches the common output. Its 400 ohm on-resistance is suitable for many medium-impedance sensor and instrumentation nodes. The CMOS implementation, low-leakage characteristic, and analog switching function make the device useful when channel isolation and signal routing matter more than very high bandwidth or very low resistance. Three address-control bits select one of eight possible input paths. The selected signal can be used in either multiplexing or demultiplexing arrangements, allowing the same device family to support measurement systems, signal-distribution networks, and test systems. The exact electrical limits, address timing, channel characteristics, supply requirements, and operating-temperature limits must be confirmed in the Analog Devices MAX338 manufacturer data sheet before finalizing a circuit. Typical uses include multiplexing resistive sensor outputs into an analog-to-digital converter, selecting instrumentation channels, routing multiple test points through a shared measurement chain, and building compact signal-distribution systems. These applications benefit from the dedicated 8:1 topology and the low-leakage CMOS design. Designs requiring substantially lower on-resistance, faster switching, higher voltage operation, or differential channel handling may need a different multiplexer family. When laying out a board, route the eight analog inputs and common output as short, guarded traces, place the device close to the sensing circuitry, and keep digital address lines away from sensitive analog paths. Confirm the package pin arrangement and the manufacturer’s grounding and supply recommendations on the official data sheet. Do not infer pin functions from another MAX338 package or ordering code without checking the exact pin description table. This product summary combines the official MAX338 family description, package and routing information, temperature-code context, and application-focused engineering guidance. It also identifies the package-compatible alternatives that can be evaluated without changing the PCB footprint and highlights the principal trade-offs between low-leakage multiplexing, switching resistance, and system flexibility.

RFQ İletişim
MAX338MSE/PR3+T - 8:1 CMOS Multiplexer | Analog Devices
MAX338MSE/PR3+T

MAX338MSE/PR3+T - 8:1 CMOS Multiplexer | Analog Devices

Analog Devices MAX338MSE/PR3+T is an 8-channel or dual 4-channel CMOS analog multiplexer with a 400 ohm on-resistance, packaged in a 16-SOIC. The device connects one of eight inputs to a common output, providing low-leakage signal routing for test, measurement, control, and data-acquisition systems. It can operate from a single +4.5 V to +30 V supply or from dual supplies of ±4.5 V to ±20 V. An analog multiplexer is a semiconductor switch that routes multiple analog inputs through a shared output path. The MAX338 belongs to the broader interface-IC hierarchy: analog multiplexer, analog switch, interface IC, and semiconductor. Its eight-channel configuration can also be divided into two independent 4-channel sections, making it useful when a system must select among several sensor, instrument, or control signals without duplicating downstream amplifiers and converters. The MAX338 is identified as a low-leakage CMOS analog multiplexer. Its 400 ohm on-resistance supports practical routing of medium-impedance analog sources, while a listed leakage figure of 20 pA is useful when measuring high-source-impedance signals. The 16-SOIC package provides a conventional surface-mount footprint suitable for established test-and-measurement boards and industrial control equipment. The MAX338 family is designed around a single multiplexer architecture that can support either an 8:1 arrangement or a dual 4:1 arrangement. The manufacturer describes the MAX338 and MAX339 as pin-compatible upgrades for the DG508A and DG509A, emphasizing their role as established interface-building blocks for instrumentation systems. Their ability to operate from dual supplies also supports bipolar signal ranges where common-mode headroom is required. Typical uses include automated test equipment, data-acquisition systems, industrial process monitoring, laboratory instrument input selection, battery and power-system measurement, and control boards that route several analog channels to a single amplifier or converter. The dual 4-channel capability can shorten signal paths when two groups of four sources must be selected independently. Layout should give priority to keeping mux input and output traces short, maintaining a continuous ground reference, and preventing switched high-impedance nodes from coupling adjacent channels. The power and ground connections must be decoupled close to the device, while unused control and channel inputs should be connected according to the pin-description table in the Analog Devices MAX338 data sheet. This product summary combines the manufacturer family information with distributor and cross-reference records for MAX338MSE/PR3+T. It distinguishes the exact ordering code from related MAX338 package, temperature, and tape-and-reel options and provides application, comparison, and design guidance focused on selecting and implementing this 16-SOIC analog multiplexer.

RFQ İletişim
MAX339EPE+ - Dual 4:1 CMOS Analog Multiplexer | Maxim Integrated
MAX339EPE+

MAX339EPE+ - Dual 4:1 CMOS Analog Multiplexer | Maxim Integrated

The Maxim Integrated MAX339EPE+ is an 8-channel and dual 4-channel CMOS analog multiplexer in a 16-pin plastic DIP package. It routes one of eight inputs to a common output or operates as two independent 4:1 muxes, providing analog signal selection for data-acquisition, instrumentation, test, and embedded control systems. The device is designed for low-leakage operation and uses CMOS switching elements to control analog signals. An analog multiplexer is an interface IC that connects multiple signal sources to a shared processing channel. The MAX339 family combines an 8:1 configuration for the MAX338-style function with two selectable 4:1 sections in the MAX339EPE+. Within the broader hierarchy, the part is an analog switch, then a multiplexer, then an interface IC used to reduce the number of input channels required by an analog-to-digital converter, test instrument, or signal-conditioning system. The principal architectural benefit is channel consolidation. Instead of routing eight external wires directly to a processor or measurement circuit, a designer can connect eight source signals to the multiplexer and select the required channel at the common output. The dual 4:1 organization provides two independent routing groups, which can simplify layouts where two separate analog buses must each select one source. Its 16-pin PDIP package also supports conventional through-hole assembly and prototyping. The MAX339EPE+ is categorized as an industrial-temperature-grade component. Its CMOS implementation and low-leakage behavior are important when the multiplexed signals are low amplitude, because leakage through an imperfectly off switch can create an error path between channels. Designers must still evaluate signal amplitude, source impedance, bandwidth, charge injection, switching speed, and the complete off-state leakage path against the accuracy required by the end application. Typical uses include multiplexed sensor acquisition, automated test equipment, industrial control modules, laboratory measurement systems, communications equipment, and embedded data-acquisition platforms. In each case, the common output is connected to downstream analog circuitry while digital control signals determine which source reaches that output. The multiplexer reduces input wiring and can make a compact analog front end easier to route on a printed circuit board. PCB design should keep sensitive analog traces away from high-current switching paths and provide a low-impedance ground reference. Decoupling capacitors should be placed near the device's supply and ground pins, while the selected signal source should have a stable reference within the device's input voltage range. Confirm all absolute maximum ratings, logic thresholds, leakage limits, and recommended operating conditions in the manufacturer datasheet before releasing production artwork. This product record consolidates the verified device classification, package information, sourcing reference, and engineering guidance into one design resource. It also separates confirmed characteristics from parameters that must be checked in the manufacturer datasheet, helping engineers plan the mechanical footprint, interface architecture, and signal-integrity requirements before committing to a PCB design.

RFQ İletişim
MAX3483AEASA+ - 3.3V RS-485/422 IC | Analog Devices
MAX3483AEASA+

MAX3483AEASA+ - 3.3V RS-485/422 IC | Analog Devices

The Analog Devices MAX3483AEASA+ is a 3.3 V-powered RS-485/RS-422 half-duplex transceiver with 20 Mbps maximum data rate, ±20 kV ESD protection, and an 8-pin SOIC package. It combines one driver and one receiver in a compact surface-mount package designed for industrial-control, telecommunications, and EMI-sensitive data links. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts between digital logic levels and differential bus signals. Differential signaling supports noise immunity and common-mode tolerance in industrial environments. The MAX3483AE family belongs to the RS-485/RS-422 transceiver hierarchy, where these interface ICs sit between a host controller and a balanced communication cable. The MAX3483AEASA+ operates from a single 3.3 V supply and uses slew-rate-limited signaling to reduce electromagnetic interference and cable reflections. Its stated 20 Mbps data rate supports high-speed point-to-point links, while its ±20 kV ESD protection improves robustness against electrostatic discharge on connector-exposed lines. The integrated driver and receiver reduce the component count required for a half-duplex communications port. The 8-pin SOIC package is widely used for compact industrial and communications equipment. Because this is a bus transceiver rather than a power semiconductor, its principal design concerns are interface topology, cable length, termination, grounding, logic compatibility, and signal integrity rather than SOA-based power calculations. Slew-rate control reduces high-frequency harmonics, although the fastest supported data rate remains dependent on the complete transceiver, cable, connector, and receiver arrangement. Typical uses include industrial-control local area networks, telecommunications equipment, point-to-point data links, factory automation interfaces, and external communication ports exposed to electrostatic discharge. A half-duplex implementation places the driver and receiver in a shared bus arrangement and requires controlled switching so that the receiver is not exposed to an active driver output. For a robust implementation, route the differential pair as a closely coupled pair, connect the bus termination only at the physical ends, and place ESD protection close to external connectors. Verify that the controller logic levels, cable impedance, grounding method, and selected data rate are compatible with the complete system rather than treating the IC alone as a guarantee of bus performance. This page combines manufacturer specifications, application guidance, structured comparisons, and design-oriented notes to clarify where the MAX3483AEASA+ fits. It also distinguishes confirmed package, voltage, data-rate, and ESD attributes from parameters that require verification against the complete system design.

RFQ İletişim
MAX3483AEASA+T - 3.3V 20Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3483AEASA+T

MAX3483AEASA+T - 3.3V 20Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3483AEASA+T is a 3.3V-powered RS-485/RS-422 interface transceiver with one driver and one receiver, a 20Mbps maximum data rate, and ±20kV ESD protection in an 8-pin SOIC package. Its slew-rate-limited driver reduces unwanted electromagnetic interference while supporting reliable point-to-point and multidrop industrial communication. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level signals into balanced differential signals and converts received differential signals back into CMOS-compatible data. The MAX3483 family belongs to the broader transceiver hierarchy: RS-485 and RS-422 interface transceiver, interface IC, data converter, and semiconductor. These differential interfaces improve noise immunity over single-ended communication and support longer cable runs in electrically noisy environments. The device operates from a 3.3V supply, supports data rates up to 20Mbps, and provides ±20kV ESD protection. Slew-rate-limited driver operation reduces edge-rate harmonics and ringing on the bus, making the interface suitable for EMI-sensitive equipment. The integrated half-duplex transceiver combines a differential driver and differential receiver, while separate driver-enable and receiver-enable controls provide flexible bus-direction management. MAX3483AEASA+T is one driver plus one receiver in an 8-pin industry-standard SO package. The receiver is designed for differential RS-422 or RS-485 buses, and the driver produces balanced differential outputs. This arrangement suits systems in which the host processor handles timing, direction control, bus arbitration, fault detection, and higher-level protocols independently of the physical interface. Typical applications include industrial-control networks, telecommunications equipment, building automation, instrumentation, data acquisition, and EMI-sensitive transceiver modules. A single MAX3483AEASA+T is also useful for point-to-point links where the system requires a compact, low-voltage RS-485 endpoint. Multidrop designs can add multiple transceivers, but the system designer must manage termination, biasing, grounding, and node-enable sequencing. Place the transceiver close to the connector and route the balanced bus pair as a coupled pair on the PCB. Keep the ground reference and differential traces away from switching nodes and high-current paths. Verify signal polarity, termination, common-mode range, bus loading, and protocol-specific idle states before releasing a production design. This page combines the manufacturer's key electrical and application facts with package-aware comparisons, drop-in family options, practical PCB guidance, and direct answers for engineers evaluating the MAX3483AEASA+T.

RFQ İletişim
MAX3483CPA+ - 3.3V 250kbps RS-485 Transceiver | Analog Devices
MAX3483CPA+

MAX3483CPA+ - 3.3V 250kbps RS-485 Transceiver | Analog Devices

The Analog Devices MAX3483CPA+ is a 3.3V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a 250kbps data rate, and an 8-pin PDIP package. It is designed for low-power serial communications where slew-rate limiting reduces electromagnetic interference and helps control cable reflections. The verified product data identifies the device as a true RS-485/RS-422 transceiver with a 3.3V supply range, commercial through-hole packaging, and receiver hysteresis of 50mV. An RS-485 transceiver is an interface IC that converts digital logic-level signals into differential bus signals and converts received differential signals back into logic-level data. RS-485 is commonly used for longer-distance, noise-tolerant industrial communication, while RS-422 provides a related differential signaling method. The MAX3483CPA+ belongs to the interface IC hierarchy: transceiver, communication interface, interface IC, and semiconductor. Its key verified features include one transmitter and one receiver, 250kbps operation, 3.3V operation, half-duplex communication, 50mV receiver hysteresis, and slew-rate-limited signaling. These characteristics suit equipment interfaces, industrial control links, instrumentation, and embedded systems that require a compact, low-power differential bus interface. The slew-rate-limited driver is particularly useful when longer cables or imperfect terminations create reflection concerns. The MAX3483CPA+ uses a true differential bus architecture rather than a single-ended logic output. Designers must still provide the correct bus topology, cable termination, common-mode handling, grounding, and protection for their installation. The driver and receiver are combined in one package, but the bus interface still requires external application-specific components such as termination resistors, protection devices, and decoupling capacitors. Typical applications include industrial automation, factory equipment, building controls, process monitoring, data acquisition, and embedded communications. A half-duplex arrangement allows the same pair of conductors to transmit and receive, although software or hardware flow control is needed to prevent simultaneous transmission and reception. The verified sources identify the MAX3483 family as low-power 3.3V transceivers, but detailed electrical limits, absolute maximum ratings, and pin-level values are not supplied in the prompt. For a new design, verify the complete manufacturer datasheet for supply tolerance, input and output thresholds, driver current, receiver sensitivity, timing, temperature limits, and ESD information before committing to the PCB. This page distinguishes verified product facts from unavailable parameters and does not infer specifications that were not present in the supplied data.

RFQ İletişim
MAX3483CSA+ - 3.3V 10Mbps RS-485 Transceiver | Maxim
MAX3483CSA+

MAX3483CSA+ - 3.3V 10Mbps RS-485 Transceiver | Maxim

The Analog Devices MAX3483CSA+ is a 3.3V-powered RS-485/RS-422 transceiver with one driver and one receiver, 10Mbps capability, and slew-rate limiting in an 8-SOIC package. It is designed for low-power, low-voltage serial communication systems where the physical layer must support both differential signaling standards. The verified distributor listings identify the device as a half-driver, half-receiver RS-422/RS-485 interface IC, while the manufacturer page describes the MAX3483 family as low-power transceivers for these protocols. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into differential line signals and receives differential line signals back into logic-level data. The differential architecture helps reject common-mode noise and supports communication over longer cables or noisier industrial environments. The MAX3483 family combines a transmitter, receiver, and driver-enable control in one package, reducing the number of discrete interface components required in a point-to-point or multidrop RS-485 link. Key verified characteristics include 3.3V operation, operation to 10Mbps according to the manufacturer product-page description, one driver and one receiver per device, and slew-rate-limited operation. The manufacturer product page states that the MAX3483 slew-rate-limited drivers minimize electromagnetic interference and reduce reflections caused by improperly terminated cables. Distributor listings also classify the part as an RS-422/RS-485 interface IC and identify the 8-SOIC package. The device is suitable for industrial equipment, instrumentation, building automation, data acquisition, and embedded control links that require a compact differential interface. A driver-enable input supports direction control in half-duplex RS-485 systems, allowing the transmitter to be disabled when the bus is not being driven. The receiver can then monitor the bus without creating a line conflict. Exact pin names, electrical limits, receiver thresholds, propagation delays, and temperature ratings must be taken from the manufacturer datasheet before final circuit design. For layout, place the transceiver close to the connector and keep differential traces short, matched, and continuous. Provide the supply bypassing and protection required by the selected system-level interface requirements. RS-485 cables normally benefit from termination, biasing, and common-mode protection, but those network components should be designed from the actual cable length, topology, baud rate, and grounding arrangement. This product page consolidates verified manufacturer and distributor information, package classification, source links, and application guidance. It does not invent electrical values absent from the supplied data; consult the MAX3483CSA+ manufacturer datasheet for the complete pinout, timing, electrical characteristics, recommended operating conditions, and application circuit.

RFQ İletişim