Ürünler (44.000+)

MAX3243IPWRE4 - 3.3V 250kbps RS-232 | Texas Instruments
MAX3243IPWRE4

MAX3243IPWRE4 - 3.3V 250kbps RS-232 | Texas Instruments

Texas Instruments MAX3243IPWRE4 is a multichannel RS-232 line driver and receiver operating from 3 V to 5.5 V, supporting data rates up to 250 kbps and ±15 kV human-body-model ESD protection in a 28-pin TSSOP package. The device provides three drivers and five receivers, making it suitable for compact industrial, embedded, and communications equipment requiring a single-level RS-232 interface. An RS-232 transceiver is an interface IC that converts between single-ended digital logic signals and the voltage levels used by the RS-232 standard. It belongs to the hierarchy of interface ICs, communication interfaces, serial-interface transceivers, and semiconductors. Each driver converts logic-level inputs into RS-232 outputs, while each receiver converts differential noise-resistant inputs into logic-level outputs. This bidirectional conversion supports point-to-point serial links between equipment, controllers, test systems, and peripheral modules. The MAX3243 family operates across a 3 V to 5.5 V supply range, allowing operation from both 3.3 V and 5 V systems. Its maximum signaling rate of 250 kbps suits control links, industrial equipment, instrumentation, and legacy serial connectivity. Three driver channels and five receiver channels provide more receive capacity than transmit capacity, allowing several incoming RS-232 signals to be monitored while supporting three outbound connections. The ±15 kV HBM ESD rating adds board-level protection for exposed serial ports. The E4 ordering suffix identifies the lead-free 28-pin TSSOP configuration shown in the product ordering information. This surface-mount package supports automated assembly while requiring careful layout around the RS-232 connector and supply rails. The device is not a modern differential serial transceiver: it is intended for point-to-point RS-232 signaling rather than RS-485 multidrop networks, USB, or differential Ethernet interfaces. Its design includes the voltage levels, slew behavior, and receiver thresholds associated with RS-232. Typical applications include industrial control panels, barcode and labeling equipment, security and access-control systems, serial-to-embedded-controller links, test instrumentation, and point-to-point service interfaces. A design can pair the MAX3243 with a microcontroller UART for logic-side connections while using a DE/RE-style control strategy where driver outputs are intentionally disabled. The receiver count also supports monitoring several incoming alarm, status, or sensor signals through separate RS-232 sources. For reliable implementation, place the transceiver close to the connector, keep RS-232 traces short and away from clocks or switching nodes, and provide the decoupling and protection required by the application. Decoupling capacitors should be placed adjacent to the supply and ground pins. External protection may still be needed for exposed cables because the on-chip ±15 kV HBM rating is a device-level specification rather than a guarantee of complete connector immunity. This page combines manufacturer specifications, drop-in substitution guidance, application-focused engineering notes, and a parameter comparison organized for PCB designers and component engineers evaluating the MAX3243IPWRE4 for 3.3 V or 5 V RS-232 designs.

RFQ İletişim
MAX3243IPWRG4 - 250kbps RS-232 Transceiver | Texas Instruments
MAX3243IPWRG4

MAX3243IPWRG4 - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243IPWRG4 is a 3-to-5.5 V multichannel RS-232 line driver and receiver rated for data rates up to 250 kbps, with plus or minus 15 kV human-body-model ESD protection in a 28-pin TSSOP package. The device integrates three RS-232 drivers and three receivers with AutoShutdown capability, allowing the supply current to fall to 1 uA when no valid signal is detected. An RS-232 transceiver is an interface IC that converts between single-ended, bipolar logic-level signals used by host systems and the differential voltage signaling required by RS-232 equipment. Within the interface hierarchy, the MAX3243 combines a line driver, line receiver, voltage-level translation, and electrostatic-discharge protection into one low-voltage CMOS device. This integration reduces board area and component count while maintaining compatibility with powered-down portable and industrial equipment. The MAX3243IPWRG4 operates from 3 V to 5.5 V, making it suitable for systems using either 3.3 V or 5 V power rails. Its 250 kbps maximum data rate supports standard serial links used for instrumentation, industrial control, point-of-sale equipment, and data acquisition. The 28-pin TSSOP package has a stated 0.65 mm terminal pitch and 5.30 mm body width, enabling compact surface-mount layouts where a larger package would be inconvenient. AutoShutdown provides an important power-management advantage for portable and intermittently connected systems. When the receiver detects no valid RS-232 signal, the device can enter a shutdown state and reduce supply current to 1 uA. Resume timing and capacitor sizing should still be evaluated against the system communication protocol, particularly when the remote transmitter can remain connected but idle for long periods. Typical uses include industrial serial controllers, laboratory interfaces, barcode scanners, security equipment, and embedded service ports. The three-driver, three-receiver arrangement works well for compact dual-ended links, while the protected low-voltage interface suits systems that need reliable translation between CMOS logic and RS-232 levels. Designers should account for the voltage levels and grounding requirements of the connected RS-232 equipment when evaluating signal integrity. Place the device close to the connector and use short, appropriately terminated signal routes for the highest practical noise immunity. Follow the manufacturer datasheet for external charge-pump capacitors, driver output wiring, receiver input handling, and ESD layout. Verify that the power rail, logic levels, line-direction control, and operating temperature meet the complete system requirements before releasing the PCB. This product record combines electrical specifications, package details, pin-location guidance, application fit, and qualified drop-in comparison information. It also highlights practical power-management and layout considerations so engineers can assess the MAX3243IPWRG4 against other RS-232 interface choices before committing to a board design.

RFQ İletişim
MAX3243MDBREP - 3V/5.5V 250kbps RS-232 Transceiver | TI
MAX3243MDBREP

MAX3243MDBREP - 3V/5.5V 250kbps RS-232 Transceiver | TI

Texas Instruments MAX3243MDBREP is a 3 V to 5.5 V multichannel RS-232 line driver and receiver operating at up to 250 kbps, with ±15 kV human-body-model ESD protection and a 28-pin SSOP package. The device provides three line drivers, five line receivers, and a dual charge-pump circuit for generating the bipolar voltages required by RS-232 line drivers. An RS-232 transceiver is an interface IC that converts logic-level signals from a host, controller, or peripheral into RS-232-compatible line levels and converts received line-level signals back into digital logic. The MAX3243 belongs to the interface IC, communications transceiver, and RS-232 line-driver/receiver hierarchy. Its multichannel arrangement supports equipment that requires several data lines but not a full nine-line desktop serial port. The MAX3243 operates from a single 3 V to 5.5 V supply, allowing operation from 3.3 V and 5 V systems. Its 250 kbps data rate is suitable for asynchronous serial links whose required baud rate remains below that operating limit. Pin-to-pin ESD protection of ±15 kV applies to the serial-port connection pins, including ground, according to the Texas Instruments MAX3243 datasheet. Internally, the MAX3243 combines three drivers, five receivers, and a dual charge-pump circuit. The charge pump generates the positive and negative voltage rails needed by the line drivers while allowing operation from a low-voltage single supply. The interface meets the electrical requirements of TIA/EIA-232-F and is intended to sit between an asynchronous communication controller and a serial-port connector. Typical uses include industrial control equipment, instrumentation, data acquisition systems, point-of-sale terminals, and embedded serial interfaces. The three transmitters and five receivers make the device useful for designs combining several command, status, and data paths while keeping the external power supply simple. The enhanced-product ordering option is suited to applications requiring the military temperature range and enhanced environmental screening. Layout is critical because RS-232 driver outputs carry high-voltage transitions, while receiver inputs are sensitive to electrical noise. Keep charge-pump and receiver-capacitor connections short, provide a solid ground reference, and route serial traces away from clocks, switching nodes, and high-current return paths. Confirm that the selected external capacitors satisfy the datasheet recommendations and that connector-side protection is coordinated with the IC's ±15 kV HBM rating. This product guide combines the manufacturer's electrical specifications, ordering information, package details, and practical RS-232 design guidance. It also identifies the verified pin-compatible MAX3243IDBR option while clearly separating package, temperature, and qualification differences that must be reviewed before design substitution.

RFQ İletişim
MAX3243MPWREP - 3/5 RS-232 Transceiver | Texas Instruments
MAX3243MPWREP

MAX3243MPWREP - 3/5 RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243MPWREP is a 3V-to-5.5V multichannel RS-232 line driver and receiver in a 28-pin TSSOP package. It integrates three line drivers, five line receivers, and a dual charge-pump circuit, providing the electrical interface between an asynchronous communication controller and a serial connector. The device supports data rates up to 250 kbps and includes ±15 kV human-body-model ESD protection on the serial-port connection pins. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into digital logic levels. The MAX3243 belongs to the RS-232 transceiver family, within the broader interface IC and semiconductor hierarchy. Its integrated charge pumps generate the positive and negative voltages required by RS-232, reducing the need for external discrete supply circuitry. The principal features of the MAX3243MPWREP are its three-driver, five-receiver configuration, 3V-to-5.5V supply operation, and 250 kbps data-rate capability. The 3V minimum supply voltage supports integration with modern low-voltage digital controllers, while the 5.5V maximum accommodates conventional 5V systems. Pin-to-pin ±15 kV HBM ESD protection adds robustness at exposed serial connectors. The device includes a dual charge-pump circuit to support RS-232 signal levels from a single supply. Five receivers allow multiple incoming channels to be monitored, while three drivers support outbound RS-232 connections. The asymmetric channel count makes the device suitable for designs that require more receive capability than transmit capability, such as control, monitoring, or diagnostic equipment. Typical applications include industrial serial controllers, point-of-sale terminals, instrumentation, data-collection systems, and RS-232 port expansion. The 250 kbps maximum data rate is appropriate for asynchronous control links and moderate-rate data transfers. System designers must still account for cable length, connector exposure, signal integrity, and the electrical limitations of the RS-232 standard. Decoupling capacitors should be placed close to the charge-pump and supply pins, while external protection may be needed when cables extend beyond the enclosure or connect to electrically noisy equipment. Verify the pin configuration and capacitor values in the manufacturer datasheet before layout because the dual charge-pump topology depends on correct external capacitor placement. This page combines the MAX3243MPWREP electrical characteristics, drop-in replacement options, application guidance, and practical layout considerations to support faster component selection and board-level implementation. It also provides a concise comparison of channel count, voltage range, data rate, protection, package, and temperature coverage for engineering review.

RFQ İletişim
MAX3245ECAI+ - 1Mbps 3/5 RS-232 Transceiver | Analog Devices
MAX3245ECAI+

MAX3245ECAI+ - 1Mbps 3/5 RS-232 Transceiver | Analog Devices

The Analog Devices MAX3245ECAI+ is a 3.0V-to-5.5V, ±15kV ESD-protected RS-232 transceiver with three drivers, five receivers, 1Mbps data rate, 1uA shutdown current, and a 28-pin SSOP package. An RS-232 transceiver is an interface IC that converts between complementary logic-level signals and the voltage-defined bipolar signaling used by RS-232 equipment. It belongs to the transceiver class within interface ICs, bridging UART, microcomputer, industrial-control, and communications systems. The MAX3245 family supports EIA/TIA-232 and V.28/V.24 communication interfaces while reducing the number of external components needed for a practical RS-232 port. Three driver channels and five receiver channels support multi-drop or multi-peripheral point-to-point arrangements. Its 1Mbps maximum data rate is suitable for moderate-speed serial links, and the ±15kV ESD rating adds protection for exposed connector-facing circuitry. The 3.0V-to-5.5V supply range accommodates both 3.3V and 5V system rails. AutoShutdown Plus provides low-power behavior for systems where power consumption matters during idle periods. The MAX3245ECAI+ uses the MAX3245E device family and is identified with the E suffix, 28-pin SSOP package, and industrial-temperature ordering code in the supplied distributor data. The verified distributor listings describe the device as a full RS-232 transceiver with three drivers and five receivers. The exact internal channel pinout, electrical limits, charge-pump capacitor requirements, and package dimensions require confirmation from the manufacturer datasheet before layout or replacement approval. Typical uses include USB-to-RS-232 adapters, industrial serial consoles, instrumentation, data acquisition, embedded control boards, and service ports. In each case, the transceiver provides the physical-layer conversion while the attached UART or processor handles framing and protocol software. The 1uA shutdown specification can reduce standby current when the port is not actively used, provided the AutoShutdown Plus control and external network are configured correctly. For PCB design, place the device close to the RS-232 connector, route driver and receiver traces away from sensitive analog or high-speed digital signals, and verify the required external charge-pump capacitors against the datasheet. This page combines verified distributor specifications, source traceability, replacement analysis, and application guidance; it does not invent unprovided pin assignments or pricing values.

RFQ İletişim
MAX324CPA+ - Precision SPST Analog Switch | Maxim
MAX324CPA+

MAX324CPA+ - Precision SPST Analog Switch | Maxim

The Maxim Integrated MAX324CPA+ is a precision, single-supply, normally closed SPST analog switch with two independent channels, packaged in an 8-pin PDIP. It operates from 2.7 V to 16 V, supports 1:1 signal routing, and is specified with a 60 ohm on-resistance in the distributor listing for this exact device. An analog switch is an integrated semiconductor device that connects or discloses signal paths under digital control. The MAX324CPA+ belongs to the analog switch family within the broader interface IC category. Its normally closed configuration provides a defined signal path when the control input is inactive, making it useful for precision routing in test systems, communication equipment, audio and video circuits, and battery-powered instruments. Key features include two SPST channels, operation from a single 2.7 V to 16 V supply, and low power consumption of approximately 5 microwatts. The device is TTL compatible when operated from a single 5 V supply. Maxim identifies the MAX324 as a production part, and the MAX324CPA+ is offered in a commercial temperature grade in an 8-pin through-hole PDIP package. The switch architecture is designed for low-power single-supply operation rather than high-voltage or high-current switching. Its on-state resistance and leakage characteristics determine the signal attenuation and off-state isolation introduced into the selected path. Users should evaluate those analog parameters against the impedance and noise requirements of the source and destination circuits. Typical uses include selecting between precision analog signals, routing DAC or ADC channels, controlling communication-system signal paths, and managing audio or video test points. The MAX324CPA+ also suits battery-powered equipment because its low-power operation reduces the energy required when the switch remains in its default state. When designing a PCB, preserve the 8-pin PDIP footprint and route sensitive analog conductors away from digital control traces. Check the supply voltage, control logic levels, and signal amplitude before connecting external circuitry. The manufacturer datasheet pin-description table should be used when assigning tracks and connector positions.

RFQ İletişim
MAX32550-LCS+T - Secure Cortex-M3 MCU 1MB Flash 121-CTBGA | ADI
MAX32550-LCS+T

MAX32550-LCS+T - Secure Cortex-M3 MCU 1MB Flash 121-CTBGA | ADI

The Analog Devices (formerly Maxim Integrated) MAX32550-LCS+T is an ARM Cortex-M3 based DeepCover secure microcontroller running at 108 MHz, integrating 1 MB of embedded Flash, 256 KB of system RAM, and 8 KB of battery-backed AES self-encrypted NVSRAM, packaged in a 121-ball CTBGA (8x8 mm). The DeepCover security subsystem is purpose-built for trusted devices such as mobile chip-and-PIN payment terminals and PIN pads. A secure microcontroller is an MCU that combines a standard processor core (here, ARM Cortex-M3) with integrated hardware cryptographic engines, secure boot ROM, tamper detection, and physically separate key storage. The MAX32550 belongs to the broader hierarchy: secure MCU -> microcontroller -> embedded processor -> integrated circuit. This device targets financial-terminal OEMs who need both application-class processing power and FIPS-grade security in a single chip. Key features include a 32-bit ARM Cortex-M3 core with 108 MHz maximum clock, 1 MB embedded Flash (1M x 8), 256 KB SRAM, 8 KB AES self-encrypted NVSRAM with battery backup, integrated cryptographic accelerators (AES, DES, SHA, RSA, ECC), hardware True Random Number Generator, secure boot ROM, physical tamper detection pins, an integrated smart-card interface (ISO 7816), magnetic-stripe reader interface, and USB 2.0 Full-Speed with on-chip PHY. The MAX32550 integrates a BGA package with 121 balls on an 8x8 mm body, allowing a compact PCB solution that includes the secure element, application MCU, and physical-tamper mesh interfaces in a single device. The NVSRAM is automatically encrypted with AES-256 keys generated and stored in a dedicated hardware block, removing software-side key management for tamper-sensitive state. The chip targets POS terminal OEMs seeking PCI PTS 4.x/5.x and EMVCo certification. Typical applications include mobile chip-and-PIN payment terminals, PIN pads, POS terminals, secure authentication tokens, EMV smart-card readers, and other financial-grade trusted devices. Industrial secure-control applications such as access-control and hardware security modules also benefit from the integrated tamper mesh. Design consideration: route the battery-backup NVSRAM domain with a separate power rail and a battery cell or super-cap; the cryptographic NVSRAM state is preserved while the rest of the chip powers down. Provide adequate ground-return vias under the CTBGA to meet EMI/magnetic-stripe-decoder noise immunity requirements. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ İletişim
MAX325EPA+ - Dual Precision SPST Switch | Maxim Integrated
MAX325EPA+

MAX325EPA+ - Dual Precision SPST Switch | Maxim Integrated

Maxim Integrated MAX325EPA+ is a precision, single-supply, dual SPST analog switch with two independently controlled circuits, 1:1 signal routing, and an 8-pin PDIP package. The device operates from 2.7 V to 16 V, has a listed on-resistance of 60 ohm at DigiKey, and is specified as a low-power component consuming approximately 5 microwatts. An analog switch is an integrated semiconductor device that routes electrical signals between circuit nodes under digital control. The MAX325EPA+ belongs to the analog switch hierarchy, which includes multiplexers, selectors, and switch matrices. Its SPST configuration provides one independent normally open connection for each of two channels, making it useful when a system must isolate, route, or protect analog signals without changing the signal level significantly. Key characteristics include two independent SPST channels, single-supply operation from 2.7 V to 16 V, a 60 ohm listed on-resistance, approximately 5 microwatt power consumption, and TTL compatibility when operated from a single 5 V supply. The device is packaged in an 8-pin PDIP measuring 0.300 inch, or 7.62 mm, across the package body. These characteristics suit compact, low-power signal-routing designs where an analog switch must operate from a limited supply rail. The MAX325EPA+ separates analog signal paths from control logic while preserving a straightforward interface. Each switch provides a 1:1 connection when enabled and disconnects the corresponding path when disabled. Single-supply operation simplifies the power architecture in battery-powered instrumentation, but the selected supply voltage and control levels must remain compatible with the switch threshold requirements. In a 5 V system, the device is described as TTL compatible. Typical applications include battery-powered measurement systems, automated test equipment, sensor signal routing, analog input selection, sample-and-hold circuitry, and communication equipment requiring two controllable analog paths. The approximately 5 microwatt power consumption is especially useful in portable equipment where every leakage and static current contributes to battery drain. PCB design should keep each switched trace short and connect the device ground pins to a low-impedance ground plane. Because the MAX325EPA+ uses through-hole PDIP construction, it is most appropriate for leaded assemblies, prototypes, industrial controllers, and test fixtures rather than compact surface-mount production boards. This product page combines distributor availability information, package identification, electrical characteristics, application guidance, and verified replacement information to support faster component selection and board-level planning.

RFQ İletişim
MAX32666GXMBT+ - Dual-Core Cortex-M4/M4F BLE 5 MCU | ADI
MAX32666GXMBT+

MAX32666GXMBT+ - Dual-Core Cortex-M4/M4F BLE 5 MCU | ADI

The Analog Devices / Maxim Integrated MAX32666GXMBT+ is a 32-bit dual-core ARM Cortex-M4/M4F microcontroller with FPU, integrated Bluetooth 5 LE radio, hardware security suite, and 1MB Flash, housed in a 121-ball CTBGA (8x8 mm) package. The part operates from 1.71V to 3.6V supply at up to 96MHz core clock and includes 192KB SRAM plus 1MB on-chip Flash. Its dual-core architecture pairs an applications processor with an always-on network co-processor, enabling low-power wearable and IoT designs without sacrificing radio throughput. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O onto one silicon die. The Cortex-M4 family adds a single-precision hardware floating-point unit (FPU) for DSP-class math, and a dual-core MCU further partitions responsibilities - one core runs application logic while the other offloads wireless stack, sensor fusion, or security tasks - reducing wake events and total system energy per task. Key features of the MAX32666GXMBT+ include Bluetooth 5 LE with 2 Mbps high-throughput and 4x long-range PHY modes, ADI TrustZone-style hardware secure element (TRUST), secure boot, true random number generator, AES-256, and SHA-256 accelerators. The integrated DC-DC converter and multiple low-power modes (Active, Sleep, Deep Sleep, Backup, Standby) yield system-level current as low as a few microamps in deep-sleep retention, critical for coin-cell and rechargeable wearables. Architecturally, the part is fabricated in a low-leakage CMOS process and uses ADI's ultra-low-power design IP. The radio block shares the same die as the application cores, eliminating external balun-matching complexity when paired with the recommended chip antenna. Hardware crypto accelerators offload TLS / DTLS handshake workloads so the M4F core can remain idle, further improving energy per transaction. Typical applications include fitness bands and smartwatches, medical wearable patches (continuous glucose monitor, SpO2), secure IoT endpoints (BLE sensor nodes), industrial asset trackers, and hearables / wireless earbuds. The wide 1.71-3.6V supply range supports direct Li-ion battery connection with internal regulation, simplifying the power tree. When designing with this part, allocate the secondary core exclusively to the BLE stack and security; do not share it with general application code. Validate PCB stack-up against the CTBGA escape pattern in the package diagram, and place the DC-DC inductor within 2mm of the LX pin to keep ripple below the AES engine's noise floor.

RFQ İletişim
MAX33040EAKA+ - +3.3V 5Mbps CAN Transceiver, ±40V Fault, SOT-23-8 | Maxim Integrated
MAX33040EAKA+

MAX33040EAKA+ - +3.3V 5Mbps CAN Transceiver, ±40V Fault, SOT-23-8 | Maxim Integrated

The Maxim Integrated MAX33040EAKA+ is a +3.3V control area network (CAN) bus transceiver with integrated overvoltage and ESD protection, housed in an 8-pin SOT-23 package. It supports data rates up to 5 Mbps, offers ±40V fault protection on the CANH and CANL bus pins, ±40 kV ESD HBM protection, and ±25V common-mode range, exceeding the ISO 11898-2 CAN physical-layer standard. A CAN transceiver (also called a CAN physical-layer device) sits between a microcontroller's CAN protocol controller and the differential CAN bus wires. It converts the microcontroller's digital TX/RX logic levels into the differential dominant/recessive voltages defined by ISO 11898-2, and simultaneously protects the sensitive MCU side from harsh automotive and industrial bus transients. Within the broader hierarchy, a CAN transceiver falls under Interface ICs > Wired Communication > CAN/LIN transceivers. Key features include a 3V to 3.6V single-supply operating range, low-current standby and silent modes, hot-plug capability, slope control for limited-data-rate applications, and TXD dominant-timeout to prevent bus lockup from a stuck dominant node. The SOT-23-8 footprint occupies roughly 9 mm² of board area, making it one of the smallest isolated-fault CAN transceivers available. Internally the device combines a differential CAN driver/receiver pair with TVS-based fault clamps and an ESD cell rated to ±40 kV HBM. The wide ±25V CMR allows it to reject large ground-shift noise typical of long industrial cables and 12V/24V battery-powered equipment, while the ±40V fault tolerance survives load-dump and jump-start events far beyond the ISO 7637 pulse ratings. Typical applications include building automation gateways, industrial drones and motor controllers, factory-floor sensors, instrumentation data links, service and educational robots, and any 3.3V MCU-based system that must communicate reliably over CAN. Its small SOT-23-8 package and integrated ±40V/±40kV protection eliminate the need for external TVS diodes, common-mode chokes, and isolation in many designs. When designing with the MAX33040EAKA+, observe the bus-termination requirement of two 120 Ω resistors (one at each end of the bus) and place a 100 nF decoupling capacitor as close as possible to the VCC pin. The SLP pin can be tied high for low-speed, slope-controlled operation or left open for normal high-speed mode.

RFQ İletişim
MAX332CPE+ - Quad SPST 175Ω Analog Switch | Analog Devices
MAX332CPE+

MAX332CPE+ - Quad SPST 175Ω Analog Switch | Analog Devices

The Analog Devices MAX332CPE+ is a four-circuit, normally open analog switch with a 175Ω on-resistance, packaged in a 16-pin PDIP. It provides 1:1 signal routing, a typical turn-on time of 1 µs, and a typical turn-off time of 500 ns, making it suitable for analog and digital signal-path switching. An analog switch is a semiconductor device that connects or disconnects a signal path under digital control. Within the component hierarchy, the MAX332CPE+ is an analog switch, also classified as a multiplexer or demultiplexer when used to route one of several lines to a common node. Its four independent SPST switches can isolate, select, or disconnect external circuit nodes. The MAX332CPE+ uses four normally open switch circuits to provide straightforward routing without a break-before-make interpretation in the product description. Its documented 175Ω on-resistance supports practical signal interconnection, while 1 µs turn-on and 500 ns turn-off timing suit control systems that need switching in the microsecond range. The 16-pin PDIP format supports conventional through-hole PCB assembly. The device is identified as a quad SPST, 1:1 analog switch with a 16-pin PDIP package. Its four-circuit architecture consolidates multiple switch functions into one package, reducing component count compared with four single-switch devices. The device is implemented as a CMOS analog switch and is intended for controlled routing of external signals rather than power conversion or high-current switching. Typical uses include signal-path isolation in test and measurement equipment, channel selection in analog front ends, sample-and-hold control paths, instrumentation interfaces, and industrial control systems. In each case, the control logic selects one of the available connections while the switch network separates the selected source from the other external nodes. Designers should verify the exact control states, pin mapping, supply requirements, allowable signal levels, and switching conditions in the Maxim Integrated datasheet before laying out a PCB. The PDIP package is mechanically straightforward to route, but the switch nodes should be positioned to minimize coupling between adjacent high-impedance paths and to keep control traces away from sensitive analog conductors. This product page combines the confirmed switch configuration, timing, resistance, and package characteristics with application guidance, engineering considerations, and drop-in alternatives. It is designed to help engineers identify the correct device faster while preserving the distinction between verified MAX332CPE+ attributes and replacement-specific data that must be checked before procurement.

RFQ İletişim
MAX334EWE+ - Quad SPST High-Speed Analog Switch, 50 Ohm, 16-SOIC | Maxim Integrated
MAX334EWE+

MAX334EWE+ - Quad SPST High-Speed Analog Switch, 50 Ohm, 16-SOIC | Maxim Integrated

The Analog Devices MAX334EWE+ is a high-speed quad SPST analog switch IC: four independent single-pole single-throw switches with 50 ohm on-resistance packaged in a 16-pin SOIC (SOP-16), powered from +5 V to +30 V single supply or plus/minus 5 V to plus/minus 15 V split supplies with CMOS- and TTL-compatible logic inputs. An analog switch is a solid-state semiconductor device that connects or disconnects an analog signal path under digital control. The switch belongs to the multiplexer family: a single SPST switch is the simplest routing element, and four of them in one package form a quad analog switch that can connect four signal sources to four loads, sample-and-hold front ends, or guard a bus. Like all CMOS analog switches, it sits between the signal world and the digital control world, bridging analog signal conditioning and logic-level control. Key features of the MAX334EWE+ include a 50 ohm on-resistance, high switching speed, break-before-make behavior for all four channels, and logic-compatible control inputs that accept both CMOS and TTL levels. The manufacturer positions it as a direct replacement for the DG201 and DG211, offering one quarter the on-resistance and five times the speed of those earlier parts. The wide supply range accepts laboratory bench rails, industrial 24 V nominal buses, and split supplies without level shifting. Technically, the device uses CMOS switch cells with independent control inputs per channel, so each switch can be steered by a separate logic signal. Low on-resistance keeps insertion loss and load-induced error small in high-impedance measurement paths, while break-before-make sequencing prevents the momentary shorting of two driven nodes that would corrupt a measurement. The MAX334EWE+ is specified for industrial temperature grade and ships in a surface-mount SOP-16 package. Typical uses include precision sample-and-hold circuits in data acquisition systems, signal routing in test and measurement instrumentation, battery-cell and supply monitoring front ends, audio and communications signal path switching, and industrial or automotive signal multiplexing where several analog lines must be selected by a controller. When designing around this device, treat each control input as a digital signal that still requires clean rise and fall times, and keep analog traces short and shielded from the switching control pins. Confirm break-before-make timing against your acquisition system and account for input capacitance and charge injection when the switched node feeds a high-gain amplifier. This page consolidates the switch function, supply and logic compatibility, drop-in replacement options, and practical routing and layout guidance in one place, so an engineer can qualify the MAX334EWE+ for a new board or an existing design revision without cross-checking several documents.

RFQ İletişim
MAX335EWG+ - 8-Channel SPST Serial Switch | Analog Devices
MAX335EWG+

MAX335EWG+ - 8-Channel SPST Serial Switch | Analog Devices

The Analog Devices MAX335EWG+ is an 8-channel single-pole single-throw analog switch with a serial digital interface, 150 ohm on-resistance, and operation from -15 V to +20 V supply voltage in a 24-pin WSOIC package. The device provides eight separately controlled switches that conduct equally in either direction, making it suitable for routing analog signals in test, measurement, industrial, and data-acquisition systems. An analog switch is a semiconductor interface that connects or disconnects signal paths under digital control. The MAX335 belongs to the broader CMOS analog-switch and interface-IC hierarchy, where the switch handles analog signal routing while a serial interface controls channel state. Each SPST channel provides one normally open path, allowing external circuitry to select among multiple signals without redesigning the analog path. The MAX335EWG+ features a nominal 150 ohm on-resistance, approximately 400 ns switching times, 90 dB isolation, and an industrial operating-temperature range from -40 C to +85 C. Its serial control reduces the number of external control pins required when multiple channels must be managed in a compact system. The analog signal path is designed to maintain consistent resistance across the specified signal range. Use the device when a system needs eight independently addressable SPST routes and can accept a serial command interface. A typical implementation places the switch between a sensor or measurement source and a downstream analog front end, allowing the controller to select test channels or isolate signal paths. The -15 V to +20 V supply range supports both positive and negative analog signal environments. PCB layout should keep analog traces short, provide a stable ground reference, and place decoupling capacitors close to the supply pins. The serial interface requires correct logic levels and signal timing; the manufacturer datasheet should be used for pin assignment and serial protocol details. Confirm the maximum signal voltage, current, and switching conditions before finalizing the design. This product page consolidates the MAX335EWG+ electrical specifications, package information, sourcing guidance, and practical design considerations into one reference for engineers evaluating serial-controlled analog routing.

RFQ İletişim
MAX336EPI+ - 16:1 Low-Leakage CMOS Multiplexer | Analog Devices
MAX336EPI+

MAX336EPI+ - 16:1 Low-Leakage CMOS Multiplexer | Analog Devices

Analog Devices MAX336EPI+ is a 16-channel, single 16:1 CMOS analog multiplexer with 400 ohm on-resistance, low-leakage characteristics, and operation from 4.5 V to 30 V in a 28-pin PDIP package. It is designed for routing multiple analog signals through a shared circuit while limiting channel-selection errors, leakage, and signal distortion. An analog multiplexer is an input-routing semiconductor that selects one of several analog inputs and connects it to a common output. The MAX336 belongs to the CMOS analog switch and multiplexer hierarchy within broader interface ICs. Its 16:1 configuration reduces the number of physical signal paths required in instrumentation, measurement, control, and data-acquisition systems where many sensor or test inputs must be scanned sequentially. Key features include a single 16:1 configuration, 400 ohm on-resistance, low-leakage CMOS operation, and a 4.5 V to 30 V single-supply range. The MAX336 family also provides a dual 8-channel configuration option and is specified for low charge injection, with 3.5 pC typical. According to the Analog Devices product page, electrostatic-discharge protection exceeds 2000 V using method 3015.7, helping protect sensitive analog nodes during handling and system integration. The MAX336 is implemented as a CMOS analog switch with controlled complementary addressing and break-before-make behavior expected of the MAX336/MAX337 family. Its low-leakage characteristic is particularly valuable when measuring high-impedance sources because off-channel leakage can create an error proportional to source impedance. The 400 ohm on-resistance must also be included in source-impedance and gain-error calculations, especially for instrumentation front ends with long sensor leads. Typical uses include battery-cell monitoring, programmable instrumentation, industrial control, automated test equipment, data acquisition, and analog signal routing. The device can consolidate 16 measurement channels into one signal chain while the surrounding system applies an address and measures each selected input. It is also suitable where leakage, rather than switching speed, is the primary concern. PCB design should keep the selected analog path short and place protection and filtering components near the relevant pins. Verify input levels, supply range, address timing, and off-channel leakage against the end-equipment accuracy budget. A PDIP package favors through-hole prototyping and repair but occupies more board area than surface-mount alternatives. This product page combines manufacturer specifications, package information, sourcing guidance, application analysis, and honest replacement evaluation. It also highlights where pin-to-pin alternatives are technically credible, avoiding the inclusion of parts that require a different footprint or materially different switching architecture.

RFQ İletişim
MAX337CWI+ - Dual 8:1 CMOS Multiplexer | Analog Devices
MAX337CWI+

MAX337CWI+ - Dual 8:1 CMOS Multiplexer | Analog Devices

Analog Devices MAX337CWI+ is a dual 8:1 CMOS analog multiplexer with 400 ohm on-resistance in a 28-pin SOIC package. The device routes one of eight analog inputs on each multiplexer section to a common output, providing 16 switch channels in one IC. Its low-leakage design makes it suitable for precision signal selection, measurement systems, and instrumentation where minimizing input loading is important. An analog multiplexer is a semiconductor switch that connects one selected input to a shared output. A dual 8:1 CMOS multiplexer expands two independent groups of eight inputs into two common outputs. This hierarchy places the MAX337CWI+ within analog switches, interface ICs, and general-purpose signal-routing devices. It reduces the number of external routing components while allowing one controller to select among multiple analog signals. The MAX337 family is identified as a 16-channel dual 8-channel, low-leakage CMOS analog multiplexer. According to the manufacturer product page, MAX337 is in production, and the manufacturer datasheet describes the device as a monolithic CMOS analog multiplexer. Its 8:1 configuration uses address-control inputs to select one input per section and route it to the corresponding common output. The listed 400 ohm on-resistance provides the principal quantified electrical characteristic for this exact listing. It determines the series loss and interaction between the selected source and destination when the switch is on. Low leakage is especially important when the mux precedes high-impedance analog nodes, because leakage current can create an error voltage proportional to the input source impedance. Typical uses include battery-cell monitoring, sensor multiplexing, data acquisition, automated test equipment, and laboratory instruments. The dual architecture is particularly useful when two related analog quantities must be selected independently, such as paired sensor outputs or two channels within a multichannel measurement system. The same common-output arrangement can also be used to share a downstream amplifier or converter between several inputs. Designers should treat the address controls as digital signals while paying attention to the analog signal range, source impedance, and leakage of the connected sources. Place bypass and signal-conditioning components close to the mux pins, keep analog routing away from high-current switching nodes, and use a suitable common-ground strategy. Review the manufacturer pin-description table and operating limits before finalizing the board layout. This page combines the manufacturer overview, distributor identification, package details, cross-reference results, and practical selection guidance for the MAX337CWI+. It also distinguishes a verified dual 8:1 replacement candidate from devices that use a different package or channel architecture, helping engineers narrow replacement decisions without confusing functional similarity with true drop-in compatibility.

RFQ İletişim
MAX3380ECUP+ - 2Tx/2Rx RS-232 Transceiver | Analog Devices
MAX3380ECUP+

MAX3380ECUP+ - 2Tx/2Rx RS-232 Transceiver | Analog Devices

Analog Devices MAX3380ECUP+ is a 2-transmitter, 2-receiver RS-232 transceiver operating from +2.35V to +5.5V, with 15kV ESD protection on both logic and RS-232 I/O pins. The device is housed in a 20-pin TSSOP package and supports low-power RS-232 communication systems requiring one interface per port. An RS-232 transceiver is an interface IC that converts between single-ended TTL/CMOS logic levels and differential bipolar RS-232 signal levels. The MAX3380ECUP+ integrates two transmit channels and two receive channels, allowing a compact design to connect a UART, embedded controller, or industrial communications equipment to an RS-232 port. Its dual charge-pump design allows the RS-232 output levels to operate from a supply as low as +2.35V while remaining compatible with +5.5V systems. Key features include a +2.35V to +5.5V operating range, two transmit and two receive channels, enhanced ESD protection rated at 15kV on both sides of the interface, and support for EIA/TIA-232 and V.28/V.24 communication requirements. The low-power architecture is suitable for battery-powered equipment and portable serial interfaces where supply current and board area are important design constraints. The MAX3380ECUP+ uses integrated charge-pump circuitry to generate the positive and negative voltage levels required by RS-232 transmitters. Its low-dropout transmitter output stage is designed to preserve compliant RS-232 output levels over the full supply range, including when the supply is close to the minimum operating voltage. The device also provides enhanced ESD protection at the logic and RS-232 pins, helping protect the connected UART or transceiver from electrostatic discharge events. Typical applications include industrial serial controllers, point-of-sale terminals, test equipment, instrumentation, embedded control systems, and battery-powered communications products. The two-transmitter, two-receiver arrangement is useful when a product needs to monitor one serial connection while transmitting on another without using two separate transceiver packages. The TSSOP-20 footprint also supports compact PCB layouts in equipment with limited connector space. When laying out the MAX3380ECUP+, place the charge-pump capacitors and interface bypass capacitors close to their associated pins. Keep RS-232 traces short and route them away from sensitive logic and clock signals. Confirm the external capacitor values, supply voltage, and UART logic levels against the manufacturer datasheet before releasing a PCB layout. This product data combines the manufacturer interface overview with structured application guidance, drop-in replacement information, comparison parameters, and practical layout notes. It is intended to help engineers evaluate the MAX3380ECUP+ for compact, low-voltage RS-232 interfaces while keeping the implementation focused on verified electrical and package characteristics.

RFQ İletişim
MAX3380ECUP+T - 2Tx/2Rx RS-232 Transceiver | Analog Devices
MAX3380ECUP+T

MAX3380ECUP+T - 2Tx/2Rx RS-232 Transceiver | Analog Devices

The Analog Devices MAX3380ECUP+T is a 2-transmitter, 2-receiver RS-232 transceiver designed for +2.35 V to +5.5 V operation, with a 20-pin TSSOP package and enhanced electrostatic-discharge protection on both logic and RS-232 pins. It supports EIA/TIA-232 and V.28/V.24 communication interfaces while operating from a 1.65 V logic reference where required. An RS-232 transceiver is an interface IC that converts between single-ended TTL/CMOS logic signals and differential bipolar RS-232 signals. It belongs to the interface-IC hierarchy, connecting UART, UART-compatible controllers, microcontrollers, and industrial peripherals to physical communication links. Transceivers combine driver and receiver functions in one package, reducing board area and simplifying bidirectional serial-port implementations. The MAX3380ECUP+T provides two transmit channels and two receive channels, allowing two serial ports to share one device. Its +2.35 V to +5.5 V supply range accommodates modern 3.3 V and 5 V systems, while the VL pin provides logic-level interoperability in mixed-voltage environments down to 1.65 V. The manufacturer describes enhanced ESD protection on the TTL and RS-232 sides, with the distributor listing identifying 15 kV ESD protection on I/O and logic pins. The device combines low-power operation with high data-rate capability, making it suitable for compact communications equipment. Its integrated charge-pump circuitry supports RS-232 signal generation without a separate external DC-DC converter. Logic input and output levels are referenced to VL, allowing the interface thresholds to track a compatible mixed-logic supply rather than being tied to one fixed rail. Typical uses include industrial serial controllers, point-of-sale equipment, test and measurement instruments, medical-device consoles, security systems, and other embedded systems that exchange data over RS-232. A system can connect two UART channels to the MAX3380ECUP+T while providing shared ground wiring, proper signal polarity, and compliant cable termination. PCB layout should keep RS-232 traces away from clocks, switching supplies, and high-speed digital nets. Confirm logic thresholds against the connected UART voltage, observe the manufacturer’s charge-pump capacitor requirements, and provide the specified supply and bypass capacitance close to the device pins. This page combines the manufacturer interface description, package and ordering information, drop-in alternatives, comparison parameters, and practical PCB guidance to support faster component selection and implementation.

RFQ İletişim
MAX3380EEUP+ - 2/2 RS-232 Transceiver | Analog Devices
MAX3380EEUP+

MAX3380EEUP+ - 2/2 RS-232 Transceiver | Analog Devices

Analog Devices MAX3380EEUP+ is a 2-transmitter, 2-receiver RS-232 transceiver designed for +2.35 V to +5.5 V operation, with 15 kV ESD protection on both the RS-232 and logic pins and support for data rates up to 460 kbps. The device is offered in a 20-pin TSSOP package. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and differential bipolar RS-232 signals. It belongs to the transceiver class, then to the broader interface IC and semiconductor hierarchy. This bidirectional interface is useful when equipment must communicate over longer cable distances, tolerate ground-offset differences, or meet the electrical characteristics associated with EIA/TIA-232 and V.28 communications. The MAX3380EEUP+ uses a low-dropout transmitter output stage and a dual charge pump. These features allow RS-232-compatible output levels from supplies below +3.1 V and down to +2.35 V without increasing supply current when the supply lies within that range. Its +5.5 V maximum operating voltage also makes it suitable for systems powered from a single lithium-ion cell or a low-voltage regulated rail. The four-driver, four-receiver naming in some listings refers to two transmit channels and two receive channels rather than four independent full-duplex ports. Both RS-232 I/O pins and logic-side pins receive enhanced electrostatic-discharge protection. Typical system-level uses include data acquisition equipment, industrial controllers, service interfaces, embedded serial ports, and instrumentation that requires a compact, low-voltage RS-232 connection. For board design, treat the transmitter outputs and receiver inputs as externally exposed communication pins even when the logic-side pins are protected. Keep the interface connector and cable path away from sensitive analog circuitry, provide the required bypass capacitance close to the supply pins, and route the differential transmission traces as a pair. The transmitter should connect to the remote RS-232 port through protection and signal-conditioning components appropriate to the required surge and ESD levels. MAX3380EEUP+ is appropriate when a board needs two RS-232 receive channels and two RS-232 transmit channels from a compact, low-power interface IC. Verify cable length, data rate, connector protection, and grounding before deployment. This page combines the product specifications, qualified package details, sourcing information, replacement guidance, and practical RS-232 design considerations into a focused engineering reference.

RFQ İletişim
MAX3381ECUP+ - 2Tx/2Rx RS-232 Transceiver | Analog Devices
MAX3381ECUP+

MAX3381ECUP+ - 2Tx/2Rx RS-232 Transceiver | Analog Devices

Analog Devices MAX3381ECUP+ is a 2-transmitter, 2-receiver RS-232 interface transceiver with a +2.35 V to +5.5 V supply range, 15 kV ESD protection on I/O and logic pins, and a 20-TSSOP package. It combines EIA/TIA-232 and V.28/V.24 communication functions with low power requirements and high data-rate capability. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels used by RS-232 equipment. Within the interface hierarchy, it belongs to the RS-232 transceiver class, communication interface IC family, and broader semiconductor category. Two transmitters and two receivers allow one device to support a complete point-to-point or multi-drop serial connection when the system bus rules are observed. The MAX3381ECUP+ provides 15 kV ESD protection on both its RS-232 I/O pins and logic pins. This protection is particularly useful in industrial, industrial-control, and equipment environments where cables can be touched or exposed to electrostatic discharge. Its 2.35 V minimum supply voltage also supports systems that cannot rely on a regulated 3.3 V or 5 V rail. The MAX3381E family is designed for low-power operation while retaining high data-rate performance. The integrated charge-pump circuitry required for RS-232 voltage generation is contained in the interface IC, reducing the number of external components needed for a working communication port. The MAX3381ECUP+ is identified as a 2/2 full RS-232 transceiver in a 20-TSSOP package. Typical applications include serial service consoles, data-acquisition equipment, industrial control links, test and measurement instruments, and embedded systems that communicate with legacy RS-232 peripherals. The dual-channel arrangement is useful for designs requiring two serial paths, or one link in each direction, without using two separate interface devices. PCB implementation should preserve the device's pinout and follow the manufacturer layout guidance. Place the required passives close to their associated pins, route the RS-232 traces away from sensitive analog and clock signals, and use suitable protection and grounding practices for cables entering the enclosure. Confirm the exact pin functions and external-component values against the manufacturer datasheet before releasing the layout. This product page consolidates the verified operating range, channel configuration, ESD rating, package information, same-footprint alternatives, and application-oriented design guidance. It is intended to help engineers evaluate the MAX3381ECUP+ quickly while keeping the final schematic, PCB, and component decisions grounded in manufacturer documentation.

RFQ İletişim
MAX3381ECUP+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3381ECUP+T

MAX3381ECUP+T - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3381ECUP+T is a 2-transmitter, 2-receiver full-duplex RS-232 transceiver operating from 2.35V to 5.5V, supporting data rates up to 250kbps and providing 15kV ESD protection on I/O and logic pins in a 20-TSSOP package. It combines EIA/TIA-232, V.28, and V.24 interface requirements with low-power operation and integrated level translation. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into digital logic levels. In the broader electronics hierarchy, an RS-232 transceiver belongs to interface ICs and line-driver and receiver devices, where it protects a host controller from the voltage range and electrostatic-discharge exposure of a serial connection. The MAX3381E family supports two transmit channels and two receive channels, allowing full-duplex communication through one package. Its 2.35V minimum supply voltage supports modern low-voltage embedded systems, while the 5.5V maximum accommodates conventional 5V equipment. The 250kbps maximum data rate is suitable for industrial control links, point-of-sale equipment, data acquisition, and service interfaces. Integrated charge-pump circuitry generates the bipolar voltage required to transmit RS-232-compatible levels from a single low-voltage supply. According to the manufacturer datasheet, enhanced electrostatic-discharge protection is provided on both the TTL and RS-232 sides, covering the 15kV ESD-protected I/O and logic pins identified for this device. Typical uses include industrial serial controllers, programmable-logic or microcontroller UART links, instrumentation, and embedded control systems. The two transmitters can support separate outbound channels, while the two receivers allow simultaneous inbound monitoring or redundant communication paths when the connected system requires them. PCB design should provide a solid ground plane, place charge-pump and interface components close to the device, and preserve adequate clearances around connected RS-232 lines. Decoupling capacitors should be placed directly beside the supply pins. The 20-TSSOP footprint is compact, but its narrow lead pitch requires careful inspection and reliable assembly processes. This product page combines operating limits, interface characteristics, application guidance, package details, and same-family drop-in alternatives to support component selection and PCB design before an RS-232 interface is committed to production.

RFQ İletişim
MAX3381EEUP+ 2Tx/2Rx RS-232 Transceiver | Analog Devices
MAX3381EEUP+

MAX3381EEUP+ 2Tx/2Rx RS-232 Transceiver | Analog Devices

Analog Devices MAX3381EEUP+ is a 2-transmitter, 2-receiver RS-232 transceiver designed for +2.35 V to +5.5 V operation, with 1 uA supply current, 460 kbps data rate, and ±15 kV ESD protection on its I/O and logic pins. The device is packaged in a 20-pin TSSOP. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and differential bipolar RS-232 signals. It belongs to the transceiver and line-driver hierarchy within interface ICs, allowing equipment with TTL or CMOS logic ports to communicate with RS-232 equipment over a wired serial link. The MAX3381E combines two transmit channels, two receive channels, level translation, and electrostatic-discharge protection in one package. The MAX3381EEUP+ supports supply voltages from +2.35 V to +5.5 V, making it suitable for systems that cannot provide a conventional +5 V rail. Its 460 kbps maximum signaling rate handles common point-to-point serial-control links, while its 1 uA supply current supports low-power equipment. The ±15 kV ESD rating applies to both the RS-232 I/O pins and the logic pins. The MAX3381E family implements powered EIA/TIA-232 and V.28/V.24 communication interfaces. Powered operation means the device includes the charge-pump circuitry required to generate the bipolar voltage levels used by RS-232. This integration reduces the external discrete components normally needed around separate line drivers and receivers, although charge-pump capacitors and interface filtering still require careful PCB planning. Typical uses include industrial control consoles, laboratory instruments, data-acquisition equipment, point-of-sale terminals, and service-port adapters. The two transmitter and two receiver channels suit links requiring two serial paths, while the broad supply-voltage range supports both 3.3 V and 5 V system logic. Cable routing and connector selection remain important because RS-232 is designed for point-to-point communication rather than long multipoint networks. For a new layout, place the device close to the protected connector and route each RS-232 line directly toward its connector pin with a short path. Keep logic-side traces away from the unprotected connector side of the interface. Confirm the device's enable, shutdown, receiver-output, and driver-input states during startup so that unused channels do not create bus contention. This product record combines the manufacturer's MAX3381E family information with package, interface, speed, power, and ESD characteristics for engineering selection. It also provides verified same-package replacement context, practical layout guidance, and application-oriented comparisons that support faster component evaluation before schematic capture.

RFQ İletişim
MAX3381EEUP+T - 2/2 RS-232 Transceiver | Analog Devices
MAX3381EEUP+T

MAX3381EEUP+T - 2/2 RS-232 Transceiver | Analog Devices

Analog Devices MAX3381EEUP+T is a 2-transmitter, 2-receiver RS-232 transceiver operating from +2.35 V to +5.5 V, with 15 kV ESD protection on I/O and logic pins, in a 20-pin TSSOP package. The interface supports EIA/TIA-232 and V.28/V.24 communication while operating from a low 1 µA supply current. An RS-232 transceiver is an interface IC that converts low-voltage digital logic signals into RS-232 voltage levels and converts received RS-232 signals back into logic-compatible levels. It belongs to the transceiver and driver/receiver hierarchy, bridging UART, UART-compatible controller, and computer I/O logic with external serial cables. This bidirectional level-shifting function allows a compact system to communicate through a longer-distance, noise-tolerant serial interface. The MAX3381EEUP+T provides two transmit channels and two receive channels, supporting full-duplex point-to-point serial links. Its +2.35 V to +5.5 V operating range supports low-voltage logic systems as well as conventional +5 V equipment. The manufacturer's product page identifies 15 kV ESD protection on both I/O and logic pins, helping protect sensitive interface circuits when cables are connected or disconnected. The MAX3380E and MAX3381E families combine low power consumption with high data-rate capability. The MAX3381E variant is specified for production availability, and its enhanced ESD protection applies to both the RS-232 side and the logic pins. Independent transmit and receive channels allow full-duplex operation when the connected system assigns one driver and one receiver to each communication path. Typical uses include industrial control links, point-of-sale equipment, data-cable interfaces, instrumentation, and embedded serial ports. The dual transmitter arrangement can support two outbound RS-232 signals, while the dual receivers can monitor two incoming signals. In designs using a UART, the device can translate between the controller's logic-level pins and the voltage levels required by an RS-232 cable. When laying out the circuit, place the device close to the RS-232 connector and route driver and receiver traces away from sensitive analog or high-speed digital paths. Verify the connector's signal and ground assignments, provide the required supply bypassing, and maintain adequate board spacing to reduce surge-current exposure at the protected pins. This product page brings together the manufacturer's core electrical characteristics, package information, verified drop-in relationships, and practical interface-layout guidance. It is intended to help engineers evaluate the MAX3381EEUP+T for low-voltage RS-232 links, compare documented replacements, and plan protection and layout before releasing a PCB design.

RFQ İletişim
MAX3384ECAP - 250kbps ESD-Protected RS-232 | Analog Devices
MAX3384ECAP

MAX3384ECAP - 250kbps ESD-Protected RS-232 | Analog Devices

Analog Devices MAX3384ECAP is a low-power true RS-232 transceiver with two transmitters and two receivers, operating from a 3.0V to 5.5V single supply and supporting data rates up to 250kbps. Every transmitter output and receiver input provides electrostatic-discharge protection to ±15kV. The device is packaged in a 20-pin SSOP with a 0.65mm pitch. A true RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and differential bipolar RS-232 signals. It belongs to the broader communication-interface hierarchy: RS-232 transceiver → line driver and receiver → interface IC → semiconductor. The MAX3384ECAP combines transmit and receive functions in one package, allowing a compact design to bridge a modern controller or microcontroller with a legacy RS-232 link. The 3.0V to 5.5V operating range supports both 3.3V and 5V digital systems while avoiding the higher supply requirement associated with some older RS-232 devices. Its operation up to 250kbps makes it suitable for data acquisition, industrial control, point-of-sale equipment, and embedded systems that transfer more information than a low-speed serial link. The integrated ±15kV ESD protection strengthens the external interface against electrostatic discharge events. The MAX3384ECAP provides two transmit channels and two receive channels in a single 20-pin SSOP. This channel density allows one transceiver to serve two independent RS-232 directions or multiple device connections. A 3.3V-compatible supply range also simplifies mixed-voltage designs in which the controller core operates below 5V, while the RS-232 interface remains powered from the same rail. Typical applications include industrial serial controllers, point-of-sale terminals, access-control equipment, security systems, laboratory instruments, and embedded data-collection systems. The combination of four I/O channels, a 250kbps maximum signaling rate, low-power operation, and ±15kV interface protection addresses designs that require compact integration without the supply voltage of a legacy 5V-only RS-232 implementation. Designers should pay attention to the device's 0.65mm-pitch SSOP footprint and verify every signal and power connection against the manufacturer pin-description table before layout release. Keep the RS-232 connector-side traces away from sensitive logic where practical, and provide the external charge-pump and interface components specified by the manufacturer datasheet for the selected operating configuration. This product overview combines the MAX3384ECAP's principal electrical, packaging, protection, and interface characteristics with pin-compatible replacement guidance and practical PCB considerations. It supports faster component selection by separating application fit, channel requirements, supply compatibility, and package constraints into directly comparable engineering factors.

RFQ İletişim
MAX3384ECWN+ - 250kbps RS-232 Transceiver | Analog Devices
MAX3384ECWN+

MAX3384ECWN+ - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3384ECWN+ is a 3.0V-powered, 2/2 RS-232 transceiver supporting data rates up to 250kbps in a 20-pin SSOP package. It provides two transmit channels, two receive channels, low-power operation, and enhanced electrostatic-discharge protection for reliable point-to-point serial interfaces. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 levels back into digital logic. It belongs to the transceiver hierarchy within interface ICs, providing the physical signaling layer between data-processing equipment and a cable-connected peripheral or system. The MAX3384ECWN+ implements the EIA/TIA-232 and V.28/V.24 signaling requirements described for this device family. The principal features include operation from a 3.0V to 5.5V supply, operation up to 250kbps, two transmit outputs, two receive inputs, and enhanced ESD protection. Low-power requirements make the device suitable for systems in which interface circuitry must coexist with low-voltage digital logic. The manufacturer describes protection on both transmitter outputs and receiver inputs, which is important when cables may be connected, disconnected, or exposed to electrostatic discharge. The MAX3384ECWN+ combines true RS-232 line-driver and receiver functions in one integrated circuit. Its powered-down behavior reduces power consumption when the associated subsystem is inactive. Because the interface operates from a single low-voltage supply while generating compliant RS-232 levels, it can simplify designs that would otherwise require separate external line drivers, receivers, and protection networks. Typical uses include industrial control consoles, point-of-sale terminals, test equipment, instrumentation, and embedded systems that communicate with RS-232 peripherals through cables. The 250kbps capability is useful for moderate-speed serial links, while the integrated two-channel transmitter and receiver arrangement reduces the number of components required for bidirectional or multiport serial interfaces. The principal design consideration is the difference between RS-232 and TTL-level signaling. The MAX3384ECWN+ is intended for the RS-232 side of the connection; it does not directly accept or produce standard TTL or CMOS logic levels. Layout should preserve short return paths and appropriate grounding, while external protection and cable-length considerations should follow the manufacturer's interface guidance. This product page combines the device's core electrical characteristics, verified package information, practical application guidance, and documented same-family replacement options. It also distinguishes true pin-compatible alternatives from broader RS-232 interface products that may use a different package, voltage rating, feature set, or channel arrangement.

RFQ İletişim