Ürünler (44.000+)

MAX3483CSA+T - 3.3V RS-485 Transceiver | Analog Devices
MAX3483CSA+T

MAX3483CSA+T - 3.3V RS-485 Transceiver | Analog Devices

The Analog Devices MAX3483CSA+T is a 3.3 V-powered RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 10 Mbps, and an 8-pin SOIC package. The MAX3483 uses slew-rate-limited signaling to reduce electromagnetic interference and cable reflections, making it suitable for industrial, instrumentation, and communications links. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level data into differential bus signals and reconstructs logic-level data from differential inputs. The MAX3483 combines a balanced line driver, differential receiver, and 3.3 V power rail in one package. This places it in the interface IC hierarchy alongside bus transceivers, differential line drivers, and differential receivers while providing a compact solution for multidrop industrial buses. The device operates from a single 3.3 V supply and supports 3.0 V to 3.6 V operation. Its slew-rate-limited driver lowers the edge rate of transmitted signals, reducing EMI and reflections that can interfere with slow or poorly terminated cables. The manufacturer identifies the MAX3483 family for data rates up to 250 kbps when its slew-rate-limited operation is used to suppress cable reflections. Analog Devices also describes the MAX3483 as a 10 Mbps RS-485/RS-422 transceiver. The MAX3483CSA+T includes one transmit driver and one receive channel, allowing it to serve as a bus node in point-to-point or multidrop RS-485 networks. Its low-power design is useful in portable test equipment, industrial controllers, and distributed sensors. The separate driver-disable and receiver-enable controls support half-duplex communication and allow the receive path to be disabled when the node is not listening. Typical applications include industrial automation, RS-485 instrumentation, building-control equipment, data acquisition, and communications equipment operating from a 3.3 V rail. The slew-rate-limited driver is particularly appropriate where long cables, imperfect terminations, or adjacent high-speed circuitry could produce reflected or spurious signals. When designing the circuit, route the differential bus as a controlled-impedance pair, provide the termination and biasing required by the selected network topology, and keep the ground return close to the signal path. Confirm that the required baud rate, cable length, topology, and termination strategy are compatible with slew-rate-limited signaling before releasing the PCB layout. This page combines manufacturer specifications, package and lifecycle information, practical RS-485 design guidance, and a focused comparison of documented MAX3483 variants. These engineering details help buyers evaluate the transceiver's voltage, data-rate, package, and ESD-related options before integrating it into a new design.

RFQ İletişim
MAX3483ECPA+ - 12Mbps RS-485 Transceiver | Analog Devices
MAX3483ECPA+

MAX3483ECPA+ - 12Mbps RS-485 Transceiver | Analog Devices

Analog Devices MAX3483ECPA+ is a 3.3 V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 12Mbps, and ±15kV ESD protection in an 8-pin PDIP package. It combines a slew-rate-limited transmitter with a low-power receiver for robust point-to-point and multidrop serial communication. An RS-485 transceiver is an interface IC that converts logic-level signals into differential bus voltages and reconstructs logic-level data from a differential pair. RS-485 belongs to the broader hierarchy of interface ICs, serial-interface transceivers, and communication semiconductors. The MAX3483ECPA+ can operate as both an RS-485 and an RS-422 transceiver, making it suitable for industrial control, instrumentation, and other reliable wired-data links. The principal operating features include a 3.3 V supply, 12Mbps maximum signaling speed, ±15kV ESD protection, and slew-rate-limited RS-485/RS-422 outputs. The transmitter’s controlled edge rate helps reduce electromagnetic interference and ringing on cables. The package includes one driver and one receiver, allowing a half-duplex arrangement in which a transceiver node transmits and receives on the same differential bus. According to the MAX3483E manufacturer documentation, this is a low-power, 3.3 V device intended for industrial communication networks. Its ESD protection helps the interface withstand electrostatic discharge encountered during installation and handling. The receiver operates from the same 3.3 V supply as the transmitter, simplifying power architecture in systems that use modern low-voltage digital logic. The slew-rate-limited driver is particularly useful when long cables, imperfect terminations, or multiple connected nodes create reflection-prone conditions. Typical applications include industrial sensor networks, programmable-logic-controller communication links, instrumentation equipment, data-acquisition systems, and isolated or non-isolated supervisory control links. The MAX3483ECPA+ is also appropriate for embedded systems that require a legacy-compatible 8-pin through-hole footprint and a 3.3 V RS-485 interface. When designing around the MAX3483ECPA+, account for bus-direction control, termination at the physical ends of the differential pair, and common-mode behavior across the installed cable. A transceiver with a 12Mbps capability is not automatically required to operate at that rate; lower signaling rates can improve margin in noisy or poorly terminated installations. This product guide combines the manufacturer’s device description, package and interface characteristics, drop-in replacement assessment, comparison parameters, and practical integration guidance to support faster component selection and PCB-level planning.

RFQ İletişim
MAX3483ECSA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3483ECSA+

MAX3483ECSA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3483ECSA+ is a 3.3 V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 12 Mbps, and enhanced ESD protection of ±15 kV, packaged in an 8-pin SOIC. Its slew-rate-limited transmitter is designed to reduce electromagnetic interference and cable reflections in industrial communications links. An RS-485/RS-422 transceiver is an interface IC that converts between low-voltage digital logic signals and differential bus voltages. It belongs to the transceiver and line-driver hierarchy, which sits under interface ICs and broader semiconductor signal-interface products. Differential signaling provides common-mode rejection, allowing reliable communication over cables exposed to industrial noise, ground-potential differences, and reflected signals. Key features of the MAX3483ECSA+ include operation from a single 3.3 V supply, interoperability with 5 V logic, 12 Mbps maximum data rate, and enhanced electrostatic-discharge protection. The transmitter outputs and receiver inputs are protected to ±15 kV under the Human Body Model, ±8 kV under the IEC 1000-4-2 Contact Discharge method, and ±15 kV under the IEC 1000-4-2 Air Gap Discharge method. The device contains one low-power driver and one receiver in a half-duplex arrangement. A receiver-enable input and driver-enable input control bus direction when the transceiver is used with a shared bus. Slew-rate limiting reduces high-frequency harmonics, lowers EMI, and helps limit reflections caused by imperfectly terminated cables, although cable length, topology, and termination remain important determinants of reliable operation. Typical uses include industrial RS-485 links, RS-422 point-to-point links, building and factory automation, data acquisition systems, and embedded control networks. The half-duplex architecture is particularly appropriate for two-wire multidrop buses, while the same electrical transceiver can support four-wire RS-422 arrangements when direction control is managed appropriately. Designers should place the transceiver close to the connector or board edge, provide a continuous ground reference, route the differential pair as a tightly coupled pair, and install termination at the physical ends of the bus. The supply should be decoupled close to the VCC pin, and unused enable inputs must not float. Cable length and topology should be checked against the data rate because slew-rate limiting alone does not guarantee signal integrity on every installation. This page combines manufacturer and distributor sourcing information with practical interface-design guidance, package-specific comparisons, and application-oriented selection criteria that are not consolidated on a typical distributor listing.

RFQ İletişim
MAX3483ECSA+T - 12Mbps RS-485 Transceiver | Analog Devices
MAX3483ECSA+T

MAX3483ECSA+T - 12Mbps RS-485 Transceiver | Analog Devices

The Analog Devices MAX3483ECSA+T is a 3.3 V RS-485/RS-422 half-duplex transceiver with one driver, one receiver, 12 Mbps maximum data rate, and ±15 kV ESD protection in an 8-SOIC package. It is designed for industrial, instrumentation, and communications equipment that requires a compact, low-power differential-bus interface. An RS-485 transceiver is a type of interface IC that converts logic-level signals into differential RS-485 or RS-422 signals and converts received differential signals back into logic levels. RS-485 belongs to the differential communications interface hierarchy, where the transmitter uses complementary signal pairs to improve noise immunity and permit communication over longer cables than single-ended interfaces. The MAX3483ECSA+T combines a driver, receiver, enable control, and bus protection in one surface-mount device. Key features include a 3.3 V supply, a 12 Mbps data rate, and ±15 kV ESD protection. The slew-rate-limited driver reduces electromagnetic interference and helps limit reflections on improperly terminated cables. The half-duplex architecture allows the driver and receiver to share the same pair of bus conductors, although the direction must be controlled with the driver-enable and receiver-enable inputs. The device is a true RS-485/RS-422 transceiver intended for point-to-point and multidrop differential buses. Its one-driver, one-receiver arrangement supports systems where the transceiver must both transmit data and monitor bus activity. The MAX3483E family is identified as a production product by Analog Devices, while the suffix indicates the commercial-temperature, 8-SOIC ordering configuration. Typical applications include industrial sensor interfaces, factory automation links, building-control equipment, instrumentation, data acquisition systems, and point-to-point serial links. The 12 Mbps capability makes the device suitable for moderately high-rate control and communication networks, while the slew-rate-limited output is particularly useful on cables where reflected signals could otherwise create unwanted transitions. PCB design should place the transceiver close to the connector and keep the differential route short, symmetrical, and continuous over a controlled ground plane. Use the biasing and termination values specified by the manufacturer for the selected topology, and route the logic-side signals away from the bus connector. The unused supply and interface pins must follow the pin-description table in the manufacturer datasheet. This page combines electrical specifications, package and pin information, substitution guidance, application-focused design notes, and a parameter-by-parameter comparison to help engineers evaluate the MAX3483ECSA+T before integrating it into a new RS-485 or RS-422 design.

RFQ İletişim
MAX3483EEPA+ - 12Mbps 3.3V RS-485/RS-422 Transceiver | Maxim
MAX3483EEPA+

MAX3483EEPA+ - 12Mbps 3.3V RS-485/RS-422 Transceiver | Maxim

The Maxim Integrated MAX3483EEPA+ is a 3.3V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 12 Mbps and ±15 kV ESD protection on all pins, housed in an 8-pin through-hole PDIP package. It operates from a 3.0 V to 3.6 V supply and covers the industrial temperature range of -40 °C to +85 °C. An RS-485 transceiver is a line-driver and line-receiver pair that converts between differential logic-level signals and balanced, noise-immune differential bus wiring. The MAX3483EEPA+ belongs to the wider RS-485 transceiver family of interface ICs, which sit at the boundary between logic-level digital systems and long-distance, multi-drop field-bus cabling used in industrial automation, building controls and instrumentation networks. Key features include a slew-rate-limited driver that limits EMI and reduces reflections on unterminated or lightly terminated cables, a 50 mV receiver hysteresis that rejects noise and prevents chatter around the logic threshold, and true half-duplex operation where the driver and receiver share a single differential pair. The MAX3483EEPA+ is the E-qualified member of the MAX3483E family, which also includes the MAX3485E, MAX3486E, MAX3488E, MAX3490E and MAX3491E in the same 8-pin PDIP footprint. Architecturally the device combines a differential driver stage with a comparator-based receiver and an enable-controlled direction logic block, so the DE and /RE pins can be tied together for automatic half-duplex operation or driven separately for bus arbitration scenarios. Because the driver edges are slew limited rather than edge-triggered at full CMOS speed, the part is well suited to point-to-point and short multidrop links running at megabit-class rates. Typical uses include industrial PLC and DCS remote I/O modules, RS-485 to RS-232 gateway boards, POS and kiosk peripherals, building HVAC controllers, CNC machine tool links, and instrumentation buses carrying sensor data back to a host controller. It is also frequently used in prototype and instrumentation benches where a through-hole DIP package is easier to hand-solder and rework than a fine-pitch surface-mount alternative. When designing around this part, confirm the cable length and termination strategy against the intended data rate, keep the differential pair tightly coupled and away from switching nodes, and connect the unused receiver output to a defined logic level so noise cannot float into the digital domain. Review the pin-description table in the manufacturer datasheet when assigning PCB tracks, and use the Request a Quote form on this page for current lead time and stock.

RFQ İletişim
MAX3483EESA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3483EESA+

MAX3483EESA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3483EESA+ is a 3.3V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 12Mbps, ±15kV ESD protection, and an 8-pin SOIC package. It is designed for bidirectional serial communication over industrial, instrumentation, and control-system cables while operating from a 3.0V to 3.6V supply. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential line signals and receives those signals back as differential inputs. The MAX3483EESA+ belongs to the broader transceiver and interface-IC hierarchy, where differential signaling improves noise immunity and permits reliable communication over longer cables than single-ended interfaces. The principal features include slew-rate-limited transmitter operation, ±15kV ESD protection, a 12Mbps maximum data rate, and support for both RS-485 and RS-422 networks. Slew-rate limiting reduces high-frequency harmonics and can help limit reflections on improperly terminated cables. The single-driver, single-receiver arrangement supports point-to-point links, multidrop RS-485 networks, and RS-422 communication where compatible system signaling is required. This device operates from a 3.3V supply and is intended for low-power industrial and embedded systems. Its 8-pin SOIC package supports conventional surface-mount assembly and keeps the interface compact. Unlike an RS-232 transceiver, the MAX3483EESA+ uses balanced differential signaling, allowing the same device family to serve RS-485 and RS-422 interfaces where the network topology and termination arrangement meet the relevant interface requirements. Typical applications include industrial sensor networks, factory automation equipment, building-control nodes, instrumentation, and embedded data links. The 12Mbps capability supports faster data transfer than low-speed isolated transceivers, while slew-rate control favors EMI reduction. RS-485 multidrop networks still require correct bus topology, termination at the physical ends, and suitable common-mode margins for the installed cable and grounding arrangement. When designing the board, place the transceiver close to the connector and route the differential pair as a controlled-impedance pair. Keep the ground reference close to the cable, provide decoupling at the supply pins, and verify the receive thresholds under worst-case noise and common-mode conditions. Do not assume that the 12Mbps headline rate guarantees reliable operation over long cables; cable length, topology, termination, and transceiver capability determine the practical limit. This product page combines the manufacturer’s device description with application-oriented design guidance, package details, lifecycle information, and clearly qualified drop-in alternatives. It supports faster part selection by separating electrical function, network compatibility, ESD protection, speed, and board-level implementation considerations before a design is committed to production.

RFQ İletişim
MAX3483EESA+T - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3483EESA+T

MAX3483EESA+T - 12Mbps RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX3483EESA+T is a 3.3 V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 12 Mbps, ±15 kV ESD protection, and an 8-pin NSOIC package. The MAX3483E family combines true RS-485/RS-422 signal handling with slew-rate-limited drivers to reduce unwanted reflections and electromagnetic interference on balanced communication lines. An RS-485/RS-422 transceiver is an interface integrated circuit that converts logic-level signals between a host controller and a balanced differential bus. These differential interfaces use two conductors and common-mode rejection to improve noise immunity over longer cable runs. The MAX3483EESA+T sits within the interface IC hierarchy as a physical-layer transceiver for industrial control, instrumentation, building automation, and embedded serial networking systems. The device operates from a 3.3 V supply, with a documented operating range of 3 V to 3.6 V. Its ±15 kV ESD protection helps protect the bus-facing pins from electrostatic discharge encountered during installation or industrial operation. The 12 Mbps maximum signaling rate supports communication rates substantially above common low-speed RS-485 systems, while slew-rate-limited driver behavior reduces edge-rate harmonics on the cable. Each device contains one driver and one receiver, allowing it to serve as a half-duplex RS-485 node when the driver and receiver direction are controlled appropriately. The MAX3483 family is also identified as a true RS-485/RS-422 transceiver, distinguishing its differential bus implementation from unrelated serial-interface standards. The 8-pin NSOIC package supports conventional surface-mount assembly while keeping the transceiver compact for multi-channel interface boards. Typical uses include industrial sensor gateways, programmable logic controller communication ports, building-control equipment, instrumentation, and isolated or non-isolated serial data links. In a multi-drop RS-485 network, the transceiver interfaces a microcontroller UART with a polarity-balanced pair while the system's termination and biasing network determines signal integrity and load capability. Board design should preserve the relationship between the differential pair, the transceiver ground reference, and the logic interface. Place input and bypass capacitors close to the power pin, route the driver outputs as a controlled-impedance differential pair, and verify termination, common-mode range, and cable length against the system data rate. The slew rate is intentionally limited, so the 12 Mbps specification should not be interpreted as a guarantee of reliable 12 Mbps operation over every cable length or topology. This product page combines manufacturer specifications, commercial sourcing information, strict drop-in alternatives, package details, and practical PCB-design guidance. It also highlights the distinctions between the MAX3483E and related low-power MAX3485E, MAX3488E, and MAX3490E transceivers so engineers can identify a replacement without overlooking bus topology, speed, enable logic, or ESD requirements.

RFQ İletişim
MAX3483ESA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver
MAX3483ESA+

MAX3483ESA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver

The Maxim Integrated MAX3483ESA+ is a 3.3V-powered, 10Mbps, slew-rate-limited true RS-485/RS-422 transceiver with one driver and one receiver in an 8-SOIC package. The verified product data identifies a half-duplex transceiver, a 3V to 3.6V operating supply, and operation compatible with both RS-485 and RS-422 interfaces. An RS-485/RS-422 transceiver is an interface IC that converts digital logic-level signals into balanced differential line signals and converts received differential signals back into logic levels. These balanced interfaces improve noise immunity and allow communication over longer cable runs than single-ended links. The MAX3483ESA+ belongs to the interface-IC hierarchy, where transceivers support industrial control, instrumentation, data acquisition, and embedded serial networks. The MAX3483 family combines low-power 3.3V operation with a 10Mbps data rate. According to the Analog Devices product page, the MAX3483 and MAX3488 use slew-rate-limited drivers to reduce EMI and cable reflections while supporting error-free transmission up to 250kbps. The MAX3483ESA+ also provides a half-duplex arrangement, allowing a shared pair to support transmit and receive operation when the driver and receiver are managed appropriately. Because the device is intended for differential communication, board design must account for cable length, termination, biasing, grounding, and protection. The verified data confirms the SOIC package and 3.3V-powered RS-485/RS-422 function, but does not provide complete electrical tables or package dimensions in the supplied snippets. Applications should therefore follow the official manufacturer datasheet for pin limits, supply-current details, receiver thresholds, driver loading, and recommended external components. Typical uses include 3.3V industrial equipment, sensor interfaces, building-control nodes, laboratory instrumentation, and embedded systems that need RS-485 or RS-422 connectivity. The device is suitable when the host logic operates at 3.3V and the selected data rate matches the transceiver and cable requirements. For a new design, verify the exact package variant, confirm all eight pin functions against the official datasheet, and test the completed board with representative cable lengths and terminations. This page combines verified manufacturer and distributor information with engineering guidance while leaving unspecified parameters explicitly undetermined.

RFQ İletişim
MAX3483ESA+T - 3.3V RS-485/RS-422 Transceiver | ADI
MAX3483ESA+T

MAX3483ESA+T - 3.3V RS-485/RS-422 Transceiver | ADI

Analog Devices MAX3483ESA+T is a 3.3 V powered RS-485/RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 10 Mbps, and an 8-SOIC package. The MAX3483 family combines a true RS-485/RS-422 driver, receiver, and slew-rate-limited driver in a compact surface-mount package. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level signals into differential bus voltages and converts received differential signals back into logic levels. It belongs to the transceiver hierarchy: differential line driver and receiver, communications interface IC, interface semiconductor. True differential signaling improves noise immunity over single-ended links and supports reliable communication across industrial, instrumentation, and control environments. The MAX3483ESA+T operates from a 3.3 V supply and supports data rates up to 10 Mbps. Its slew-rate-limited driver reduces electromagnetic interference and helps limit reflections on improperly terminated cables. The manufacturer documentation also describes operation up to 250 kbps for the MAX3483ESA, so system designers should verify the speed grade and timing limits relevant to their cable, topology, and termination arrangement. The device contains one driver and one receiver, supporting half-duplex RS-485 operation when the driver-enable and receiver-enable controls are used together. Driver and receiver outputs can be placed in a high-impedance state when disabled. This control flexibility supports shared multidrop buses, direction control from a host controller, and designs that keep the receiver active while the driver is inactive. Typical uses include industrial RS-485 links, RS-422 point-to-point communications, building-control equipment, instrumentation networks, data-acquisition systems, and embedded control systems. The 3.3 V supply aligns with modern controller I/O levels, while the differential bus interface supports communication over cables that would be unreliable with ordinary single-ended logic. A successful design must select the proper cable length, data rate, topology, biasing, and termination. Place the transceiver close to the connector, route the differential pair as a tightly coupled pair, provide a continuous ground reference where appropriate, and avoid stubs that create impedance discontinuities. Confirm the logic polarity and timing of DE and RE before connecting the device to a multidrop network. This page combines the manufacturer product information, distributor listings, package information, comparison data, and practical RS-485 design guidance. It also identifies pin-compatible family alternatives and highlights the functional trade-offs that matter when selecting a transceiver for a new or existing board.

RFQ İletişim
MAX3485AEASA+ - 20Mbps 3.3V RS-485/RS-422 Transceiver | Analog Devices
MAX3485AEASA+

MAX3485AEASA+ - 20Mbps 3.3V RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX3485AEASA+ is a 3.3V-powered, half-duplex RS-485/RS-422 transceiver supporting data rates up to 20Mbps in an 8-SOIC package. It combines one driver and one receiver with slew-rate-limited operation and ±20kV ESD protection, making it appropriate for extended cable runs in electrically noisy industrial environments. The 3V to 3.6V operating range also allows use with 3.3V digital systems. An RS-485/RS-422 transceiver is an interface IC that converts logic-level transmit and receive signals into differential bus voltages and back again. RS-485 supports balanced, multipoint communication over longer distances, while RS-422 provides a balanced differential link commonly used for point-to-point equipment connections. The MAX3485AEASA+ belongs to the interface IC hierarchy, where transceivers bridge communication processors, sensors, controllers, and industrial equipment connected by copper cabling. The principal features of the MAX3485AEASA+ are its 20Mbps maximum signaling rate, 3V to 3.6V supply operation, half-duplex communication, and ±20kV ESD protection. Slew-rate limiting reduces high-frequency components generated by the driver and helps control EMI and cable reflections. These characteristics make the device useful where a conventional RS-485 transceiver would add excessive edge-rate energy to a long or noisy bus. The device contains one differential driver and one differential receiver in a compact 8-SOIC package. A half-duplex architecture allows the same differential pair to support transmission and reception, which reduces connector and PCB routing requirements. Because the interface supports both RS-485 and RS-422 applications, the exact bus configuration and termination strategy must be selected according to the number of nodes, cable length, topology, and grounding arrangement used in the final system. Typical uses include industrial supervisory control, factory automation, building controls, networked sensors, data-acquisition equipment, and point-to-point links between control electronics and remote instrumentation. In these systems, the transceiver can carry command, status, and measurement data over a differential cable while the 3.3V supply simplifies integration with low-voltage controllers. Long cables, connectors, and exposed installations also make the device's ±20kV ESD protection particularly relevant. When laying out a board, place the transceiver close to the bus connector and keep the differential route short, continuous, and away from noisy switching paths. Termination, common-mode capacitors, and pull-up or pull-down components should be selected from the system-level RS-485 or RS-422 design rather than added solely by board population. The signal integrity of the complete bus depends on cable impedance, stubs, topology, and grounding in addition to the IC. This product page combines the manufacturer's device description, verified distributor identification, package information, cross-reference options, and practical interface-design guidance. It distinguishes confirmed operating facts from parameters that still require board-level validation, helping engineers select the correct transceiver, compare pin-compatible devices, and plan a robust 3.3V differential communication link.

RFQ İletişim
MAX3485AEASA+T - 20Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3485AEASA+T

MAX3485AEASA+T - 20Mbps RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX3485AEASA+T is a 3.3V half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a 20Mbps maximum data rate, slew-rate-limited signaling, and ±20kV ESD protection in an 8-pin SOIC package. The MAX3485AEASA+T suffix identifies the Analog Devices/Maxim Integrated automotive-grade, tape-and-reel ordering variant. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts between digital logic signals and balanced differential signals. It belongs to the transceiver hierarchy within interface ICs and supports bidirectional communication over cables that may run through electrically noisy industrial environments. Balanced signaling improves noise immunity by receiving the difference between two conductors rather than relying on a single-ended voltage. The device operates from a nominal 3.3V supply, with the manufacturer listing a 3V to 3.6V operating range. Its 20Mbps data rate supports factory automation, industrial control networks, telecommunications equipment, and EMI-sensitive data links. The slew-rate-limited driver reduces high-frequency switching energy, while ±20kV ESD protection strengthens the interface against electrostatic discharge encountered during installation or connection of external cabling. Each MAX3485AE device integrates one half-duplex driver and one receiver. A shared communication path requires controlled direction switching between transmit and receive states, allowing the same pair of conductors to carry data in both directions. The analog product family also includes related MAX3483AE, MAX3488AE, and MAX3490AE devices in the same 8-pin SO package, enabling family-level design comparison when a different bus implementation or feature set is required. Typical uses include industrial-control networks, telecommunications links, instrumentation, building controls, and embedded systems that communicate with remote nodes over balanced cable. The combination of 3.3V operation, 20Mbps signaling, slew-rate limiting, and high ESD protection makes the device suitable for low-voltage controller boards that require robust differential communications without a high-power interface solution. The primary design considerations are bus termination, fail-safe biasing, transceiver enable timing, and ground handling. Place the interface close to the connector, provide a continuous return path, and evaluate common-mode voltage and cable length against the circuit operating limits. Do not substitute a 5V-only transceiver unless its supply range and electrical parameters are confirmed for the complete system. This product page consolidates the manufacturer’s electrical characteristics, package information, family comparisons, and practical interface guidance into an engineering-oriented reference. It also distinguishes direct device options from broader RS-485 alternatives and highlights where existing PCB footprints require electrical verification before substitution.

RFQ İletişim
MAX3485CPA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver | Maxim
MAX3485CPA+

MAX3485CPA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver | Maxim

The Maxim Integrated MAX3485CPA+ is a 3.3V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, 10Mbps maximum data rate, and an 8-pin PDIP package. It is designed for low-power point-to-point and multidrop serial communication links. The verified product description identifies it as a slew-rate-limited transceiver intended to reduce electromagnetic interference and cable reflections while maintaining reliable data transmission. An RS-485/RS-422 transceiver is a physical-layer interface IC that combines differential line-driver and differential receiver functions. RS-422 commonly supports point-to-point, one-driver topologies, while RS-485 supports longer multipoint buses and often requires biasing and termination. The MAX3485CPA+ sits in the interface-IC hierarchy between a host UART or microcontroller and a balanced data cable. The MAX3485CPA+ operates from 3.3V and supports communication rates up to 10Mbps. Its slew-rate-limited driver is intended to limit edge speed, which can reduce radiated EMI and ringing on imperfectly terminated cables. The device is suitable for industrial-control links, building automation, instrumentation, motor-control systems, and other embedded serial networks where a low-power differential interface is required. The 8-pin PDIP package supports through-hole PCB assembly and is distinct from the surface-mount alternatives identified in the cross-reference data. The transceiver-half architecture means the application determines whether the driver and receiver are enabled together or whether receive-only and transmit-only behavior is used through external control. Correct biasing, termination, grounding, and cable topology remain essential for reliable RS-485 operation. For design work, preserve the pinout and package when selecting a substitute. SP3485EN-L/TR is identified as a functionally equivalent, pin-compatible cross-reference with 2kV ESD protection, but its package and exact electrical details should be checked against the target design. This page consolidates verified manufacturer and distributor information, replacement data, application guidance, and design cautions for engineers evaluating MAX3485CPA+.

RFQ İletişim
MAX3485CSA+ - 10Mbps 3.3V RS-485/RS-422 IC | Maxim
MAX3485CSA+

MAX3485CSA+ - 10Mbps 3.3V RS-485/RS-422 IC | Maxim

The Maxim MAX3485CSA+ is a 3.3V-powered, half-duplex RS-485/RS-422 transceiver rated for data rates up to 10Mbps, supplied in an 8-pin SOIC package. It combines one driver and one receiver for industrial point-to-point and multidrop differential communication. Its low-power design supports compact interface equipment where supply current, board area, and signal integrity are important. The verified product information identifies the MAX3485 family as a true RS-485/RS-422 transceiver with slew-rate-limited operation and protection features. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level signals into differential bus signals and receives differential bus signals back into logic levels. RS-422 supports balanced, point-to-point communication, while RS-485 adds the ability for multiple drivers and receivers on a shared bus when the system is properly terminated and controlled. The MAX3485CSA+ belongs to the interface-IC hierarchy: transceiver, differential data interface, communications IC, and semiconductor. The MAX3485CSA+ is identified as a 3.3V-powered 10Mbps RS-485/RS-422 transceiver with an 8-SOIC package. The family description also states that the MAX3483 and MAX3488 use slew-rate-limited drivers to minimize unwanted effects, while the broader MAX348x/MAX349x family includes multiple transceivers for different operating requirements. Exact MAX3485CSA+ limits not present in the supplied search data are retained as data-needed rather than estimated. A typical use places the transceiver between a host UART or embedded controller and a cable-based RS-485 or RS-422 link. The differential bus improves noise immunity over single-ended signaling, while the 10Mbps capability supports factory automation, industrial controls, instrumentation links, building automation, and embedded data networks. Bus topology, cable length, grounding, termination, and protocol timing must be validated together because transceiver speed alone does not guarantee reliable network operation. The principal design considerations are correct logic-side voltage compatibility, supply decoupling, controlled enable and driver shutdown behavior, proper bus termination, and protection against electrostatic discharge or inductive transients. The verified distributor information lists the part in an 8-SOIC package and describes the device as a 1/1 RS-422/RS-485 transceiver, but it does not provide a complete manufacturer pinout, electrical limit table, or lifecycle classification. Engineers should consult the official MAX3485 datasheet before layout or production release. This page consolidates the supplied manufacturer, distributor, and cross-reference information with practical selection guidance. It distinguishes confirmed facts from unavailable parameters and avoids treating package variants or merely similar interface ICs as drop-in replacements without verified pin and electrical compatibility.

RFQ İletişim
MAX3485CSA+T - 3.3V 10Mbps RS-485/422 | Analog Devices
MAX3485CSA+T

MAX3485CSA+T - 3.3V 10Mbps RS-485/422 | Analog Devices

The Analog Devices MAX3485CSA+T is a 3.3V low-power RS-485 and RS-422 half-duplex transceiver with one driver and one receiver, a maximum data rate of 10Mbps, and an 8-pin SOIC package. It operates from a 3V to 3.6V supply and combines short-circuit-limited driver outputs with thermal shutdown protection. The receiver includes a fail-safe feature for improved behavior on an open, shorted, or idle bus. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over longer distances. RS-485 supports multidrop half-duplex buses, while RS-422 provides differential point-to-point links. Within the interface hierarchy, the MAX3485CSA+T belongs to the RS-485/RS-422 transceiver family of communication ICs, level translators, and semiconductor interface devices. The MAX3485CSA+T supports data rates up to 10Mbps from a 3V to 3.6V supply. Its driver uses slew-rate limiting to reduce unwanted edge energy on the bus, while short-circuit current limiting and thermal shutdown help protect the output stage. The integrated receiver provides a fail-safe response that improves system behavior when the connected line is undriven. These features make the device suitable for compact, low-power industrial communication equipment. The half-duplex arrangement shares one pair of bus pins between the driver and receiver, reducing board area and connector count. Direction control determines whether the device transmits or receives. Because a single transceiver channel is provided, systems requiring bidirectional communication must include bus-direction control and account for turnaround timing. The device also requires external bypass capacitance and controlled termination, biasing, and protection appropriate to the target network. Typical uses include industrial RS-485 sensor gateways, RS-422 motor-control links, building automation controllers, test equipment, and embedded serial-data links. The 10Mbps capability supports high-rate instrumentation, while the low 3.3V supply is compatible with modern controller and logic rails. In motor or industrial environments, protection components and galvanic isolation may be added according to the installation's surge, ESD, and ground-potential requirements. For layout, place the supply bypass capacitor close to the VCC pin and route the differential bus pair as a tightly coupled pair to minimize radiated noise and susceptibility to interference. Confirm that termination and fail-safe biasing are installed only where required by the bus topology. A single termination resistor is normally placed at each physically remote end of a standard RS-485 bus rather than at every node. This product reference combines manufacturer specifications, pin and package details, sourcing guidance, supported use cases, and practical interface-design considerations. It helps engineers compare the MAX3485CSA+T with related low-power transceivers while focusing on package compatibility, data rate, protection features, and system-level implementation.

RFQ İletişim
MAX3485ECPA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3485ECPA+

MAX3485ECPA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX3485ECPA+ is a 3.3V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 12Mbps, and ±15kV ESD protection, housed in an 8-pin PDIP package. The MAX3485 family uses slew-rate-limited drivers to reduce electromagnetic interference and reflections on improperly terminated RS-485 cables. A transceiver is an interface IC that combines a differential line driver with a differential receiver so two devices can exchange data over a balanced copper connection. In the RS-485 hierarchy, it belongs to the RS-485/RS-422 interface transceiver class and converts digital logic levels into differential bus signals. The differential signaling improves noise immunity and permits communication over distances greater than those typically supported by single-ended interfaces when the bus is correctly terminated and biased. The MAX3485ECPA+ combines 3.3V operation with ±15kV ESD protection and a 12Mbps maximum data rate. Its slew-rate-limited driver is designed to minimize cable reflections and reduce EMI, particularly when a board must interoperate with RS-485 equipment designed for controlled edge rates. The device contains one transmitter and one receiver, allowing one node to transmit and receive on a shared half-duplex bus through external direction-control and bus-enable circuitry. As a true RS-485/RS-422 transceiver, the MAX3485ECPA+ supports point-to-point or multipoint communication architectures using differential bus wiring. Receiver and driver enable controls support half-duplex operation, while a receiver output allows the host interface to interpret bus state. The 3.3V supply keeps the logic interface compatible with low-voltage digital systems, although the complete RS-485 interface still requires attention to grounding, cable topology, termination, biasing, and ESD protection at the connector. Typical applications include industrial automation equipment, test and measurement instruments, building-control gateways, data-acquisition systems, computer instrumentation, and communications links between embedded controllers and external RS-485 devices. The device is particularly useful when a compact interface must combine RS-422 or RS-485 operation with stronger ESD protection than a basic logic-level transceiver provides. When designing around the MAX3485ECPA+, place the transceiver close to the connector and route the differential pair as a controlled-impedance pair. Use a termination resistor only at appropriate physical endpoints, and verify that a single termination resistor remains connected while the bus is idle. Confirm direction-control timing and avoid allowing bus-driver and receiver-enable signals to overlap. The 8-pin PDIP package is also convenient for prototypes and through-hole industrial products where hand soldering and inspection are important. This page combines the manufacturer product information, exact-MPN listing details, interface-family context, replacement analysis, and practical PCB guidance to support faster component selection and implementation. It also distinguishes confirmed drop-in candidates from options that require further electrical verification.

RFQ İletişim
MAX3485ECSA+ - 12Mbps 3.3V RS-485/RS-422 Transceiver
MAX3485ECSA+

MAX3485ECSA+ - 12Mbps 3.3V RS-485/RS-422 Transceiver

The Analog Devices MAX3485ECSA+ is a 3.3 V-powered, half-duplex RS-485/RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 12 Mbps, ±15 kV ESD protection, and an 8-pin SOIC package. Its slew-rate-limited driver helps reduce ringing and unwanted reflections on multidrop communication buses. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential physical-layer signals and converts received differential signals back into digital data. Within the product hierarchy, this device is a transceiver, a communications interface IC, and a physical-layer interface component for industrial-control, instrumentation, and embedded data links. The MAX3485ECSA+ supports true differential signaling, making it suitable for noise-resistant communication over longer cable runs than a single-ended interface. Key features include operation from a 3.3 V supply, data rates up to 12 Mbps, ±15 kV ESD protection on the bus-facing pins, and slew-rate-limited RS-485/RS-422 driver outputs. The integrated half-duplex arrangement allows one driver and one receiver to share a communications pair, while separate driver-enable and receiver-enable inputs provide local control over bus direction and receive state. The 8-SOIC package supports compact surface-mount PCB construction. The MAX3485 family combines low-power 3.3 V operation with high-speed differential signaling. Slew-rate limiting controls the driver edge rate, helping suppress the high-frequency content that can propagate through cables, connectors, and PCB traces. The protected bus pins add an ESD barrier for ports exposed to industrial wiring, although they do not eliminate the need for correct grounding, cable routing, and external surge protection. The MAX3485E variant is identified by Analog Devices as a production 3.3 V transceiver with enhanced ESD protection. Typical applications include industrial PLC and factory automation links, RS-485 instrumentation networks, building-control equipment, data-acquisition systems, and embedded controllers requiring a compact, high-speed differential interface. The device can also support point-to-point RS-422 links where the host must control transmit and receive direction independently through its DE and active-low RE inputs. When laying out a board, place the transceiver close to the connector or transceiver isolation barrier and route the Y and Z bus traces as a tight, balanced pair. Keep the ground reference close to the cable shield connection, avoid long stubs, and follow the interface schematic and termination guidance in the manufacturer datasheet. Component values for termination and biasing should be calculated from the actual cable length, topology, node count, and baud rate.

RFQ İletişim
MAX3485EESA+ 3.3V 12Mbps RS-485/RS-422 Transceiver
MAX3485EESA+

MAX3485EESA+ 3.3V 12Mbps RS-485/RS-422 Transceiver

The Analog Devices MAX3485EESA+ is a 3.3V-powered, half-duplex RS-485/RS-422 transceiver rated for data rates up to 12Mbps, with enhanced electrostatic-discharge protection and an 8-pin SOIC package. It combines one transmitter and one receiver in a single device for bidirectional industrial communication links. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential bus voltages and converts received differential voltages back into digital logic levels. This device belongs to the transceiver hierarchy within interface ICs, where differential signaling improves noise immunity, reduces ground-potential sensitivity, and supports communication across factory, industrial, and instrumentation environments. Key features include a 3.3V supply, operation to 12Mbps, slew-rate-limited true RS-485/RS-422 signaling, and enhanced ESD protection. Transmitter outputs and receiver inputs are protected to ±15kV under the IEC 1000-4-2 air-gap discharge test, ±8kV under the IEC 1000-4-2 contact-discharge test, and ±15kV under the Human Body Model. The integrated protection reduces the need for separate bus-line protection in exposed industrial interfaces. The half-duplex architecture lets the transmitter and receiver share a differential pair through direction-control logic. The MAX3485EESA+ is designed for both RS-485 multidrop networks and point-to-point RS-422 links. Its 12Mbps capability accommodates high-rate industrial data paths while its limited slew rate reduces unwanted edge energy and electromagnetic interference compared with an unrestricted high-speed driver. Typical applications include industrial automation controllers, RS-485 communication modules, data-acquisition equipment, building-control interfaces, instrumentation, and point-to-point RS-422 links. Because the bus operates at 3.3V, it can interface directly with 3.3V logic without a separate level-shifting stage when the connected transceiver and controller use compatible thresholds. PCB design should preserve the compact 8-pin SOIC footprint and place protection, bypass, and termination components close to the relevant pins. Check the manufacturer pin-description table before assigning the driver-enable and receiver-enable functions, and verify whether the selected bus topology requires termination, biasing, or fail-safe bias resistors. This page combines manufacturer specifications, package information, interface-design guidance, comparison data, and drop-in replacement options to support faster component selection, PCB planning, and robust RS-485/RS-422 implementation.

RFQ İletişim
MAX3485EESA+T - 12Mbps RS-485 Transceiver | Analog Devices
MAX3485EESA+T

MAX3485EESA+T - 12Mbps RS-485 Transceiver | Analog Devices

Analog Devices MAX3485EESA+T is a 3.3V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a 12Mbps maximum data rate, and ±15kV ESD protection. The device is packaged in an 8-pin SOIC and accepts a 3V to 3.6V supply for industrial, embedded, and instrumentation communications. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus signals and converts received differential signals back into CMOS-compatible logic. These transceivers support noise-resistant communication over longer cables and multi-drop buses. The MAX3485E combines that differential interface function with low-power 3.3V operation and enhanced electrostatic-discharge protection for ports exposed to cables and industrial wiring. Key features include true RS-485 and RS-422 operation, a 12Mbps data rate, slew-rate-limited signaling, and integrated ESD protection of ±15kV. The single-driver, single-receiver arrangement supports both point-to-point RS-422 links and half-duplex multidrop RS-485 networks. Its 8-pin SOIC package supports conventional surface-mount assembly and is also available in a tape-and-reel ordering configuration. The differential driver reduces sensitivity to common-mode noise, while the receiver detects the polarity of the voltage difference across the A and B conductors rather than relying on an absolute signal level. Slew-rate limiting reduces high-frequency harmonics and helps control edge energy on the bus. The ±15kV protection rating adds an important margin for systems whose external connector or cable may be exposed to electrostatic discharge. Typical uses include industrial automation, factory equipment, building controls, instrumentation, data acquisition, and embedded serial links. The MAX3485E is particularly suitable for a 3.3V controller that needs an RS-485 port without a higher-voltage supply or a separate external protection network. Firmware and termination practices remain important when designing a reliable multidrop network. For a robust design, place the transceiver close to the connector, provide the required bus-termination and biasing components, connect the ground reference correctly, and route the differential pair as a tightly coupled pair. Keep protection and termination components close to the transceiver pins, and verify that the selected cables, connectors, grounding scheme, and baud rate meet the required communication distance. This page combines manufacturer product information, interface characteristics, practical bus-layout guidance, and qualified drop-in alternatives. It also highlights the distinctions among related MAX3485-family devices so engineers can compare supply voltage, fail-safe behavior, package, and transceiver behavior before releasing a replacement to production.

RFQ İletişim
MAX3485EPA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver
MAX3485EPA+

MAX3485EPA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver

The Analog Devices MAX3485EPA+ is a 3.3V-powered, slew-rate-limited, true RS-485/RS-422 transceiver with one driver and one receiver, data rates up to 10Mbps, and an 8-pin PDIP package. It is designed for low-power industrial and embedded communication links where a compact, dual RS-485/RS-422 interface is required. The verified product information identifies a 3V to 3.6V supply range, short-circuit current limiting, thermal shutdown, and fail-safe receiver behavior. Its 8-pin through-hole package is suitable for industrial control boards, instrumentation, and legacy communication equipment that uses DIP-compatible footprints. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential bus signals and receives differential bus signals back into logic-level outputs. RS-422 commonly supports point-to-point or one-driver topologies, while RS-485 supports multipoint buses and commonly uses termination and biasing. The MAX3485EPA+ combines one transmitter and one receiver in one package, making it suitable for half-duplex communication links, industrial transceivers, and systems that need a compact dual-ended interface. Key verified features include operation from 3V to 3.6V, a transmission data rate up to 10Mbps, slew-rate limiting for controlled signal propagation, short-circuit current limiting, and thermal shutdown protection that places the driver output into a high-impedance state. The receiver includes a fail-safe feature for improved behavior in bus idle or fault conditions. These functions help designers protect the communication path when the remote bus is shorted or when power dissipation becomes excessive. The MAX3485 family is positioned between general-purpose digital I/O and full physical-layer network controllers. Compared with an RS-232 transceiver, it uses differential signaling and is better suited to longer, noise-resistant industrial links. Compared with a multi-channel transceiver, the MAX3485EPA+ provides a simpler one-driver, one-receiver implementation in an 8-pin PDIP package. Its through-hole package also makes it convenient for prototypes, repair assemblies, and systems where a surface-mount footprint is not required. Typical applications include RS-485 industrial sensor links, factory automation equipment, building-control interfaces, data-acquisition systems, instrumentation, and embedded communications modules. In an RS-485 bus, the MAX3485EPA+ can be paired with a microcontroller UART, protection components, termination resistors, and bias resistors. In RS-422 applications, it can support differential point-to-point links with suitable wiring and termination. Designers should verify the PCB footprint, supply decoupling, bus termination, common-mode limits, grounding, and protection requirements before production use. The verified data does not provide every electrical limit, package dimension, temperature grade, compliance declaration, or full pin-level application detail, so those parameters should be confirmed in the manufacturer datasheet. This page combines verified product information, cross-reference results, application guidance, and drop-in alternatives.

RFQ İletişim
MAX3485ESA+ - 10Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3485ESA+

MAX3485ESA+ - 10Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3485ESA+ is a 3.3 V, low-power RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 10 Mbps, and an 8-pin SOIC package. According to the manufacturer product page, the device is in production and is designed for low-power RS-485 and RS-422 communication links. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level digital signals into differential bus signals and receives differential bus signals back into CMOS-compatible logic. RS-485 supports multipoint, half-duplex communication, while RS-422 is commonly used for point-to-point, full-duplex links. The MAX3485 family combines a driver and receiver in one package to reduce board area and simplify interface implementation. The MAX3485ESA+ is identified as a 3.3 V-powered, slew-rate-limited, true RS-485/RS-422 transceiver. The verified product information specifies a 10 Mbps data rate and an 8-SOIC package. The slew-rate-limited driver is intended to reduce unwanted signal transitions and improve communication behavior on practical differential buses. Each device contains one driver and one receiver. The interface family is suitable for industrial control, instrumentation, data acquisition, building automation, and embedded communications where differential signaling helps reject common-mode noise. The MAX3485ESA+ can also support point-to-point RS-422 links, depending on the system wiring and termination arrangement. Its low-power 3.3 V operation is useful for compact equipment where supply current and bus-energy efficiency matter. When designing a circuit, verify the exact pin functions, supply-voltage limits, driver enable logic, receiver output behavior, and termination requirements from the manufacturer datasheet before layout. RS-485 buses generally need correct biasing and termination at the physical endpoints; RS-422 links require termination appropriate to the selected topology. Never infer an alternate package or pinout from a distributor title alone. This page consolidates the verified manufacturer product information, distributor listings, packaging data, and design-oriented guidance for engineers evaluating the MAX3485ESA+. It also distinguishes the part from functional alternatives that may require different packages, logic functions, or interface architectures.

RFQ İletişim
MAX3485ESA+T - 10Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3485ESA+T

MAX3485ESA+T - 10Mbps RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX3485ESA+T is a 3.3V, low-power, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 10Mbps, and an 8-pin SOIC package. The device is designed for bidirectional serial data links where low supply voltage, compact footprint, and multipoint bus capability are important. Its +T suffix identifies the tape-and-reel ordering option, while the E suffix denotes the manufacturer's extended-temperature product line. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into differential bus voltages and receives differential bus voltages back into CMOS-compatible logic signals. It belongs to the communication interface IC hierarchy: transceiver > RS-485/RS-422 interface > differential line driver and receiver > semiconductor. The MAX3485 combines both directions of signal conversion in one package while sharing a conductor pair during half-duplex operation. Key features include a 3.3V power supply, one driver and one receiver, a 10Mbps maximum data rate, and operation as a true half-duplex RS-485/RS-422 interface. Its driver supports short-circuit protection, and the integrated receiver provides the differential input thresholding required by RS-485 and RS-422 systems. The 8-SOIC package also allows reuse of existing SOIC-8 PCB layouts when a board revision changes the transceiver source. The MAX3485 family is designed for low-power communications equipment where each node must both transmit and receive over a wired bus. A controlled driver slew rate reduces unwanted high-frequency energy on the cable, while the half-duplex architecture reduces the number of transceivers and interface signals needed at each node. Exact propagation-delay, receiver-threshold, supply-current, and ESD ratings were not included in the supplied source excerpts and must be confirmed in the manufacturer datasheet before release. Typical uses include industrial data acquisition, building controls, instrumentation links, and embedded systems communicating with remote sensors over RS-485. It is also appropriate for point-to-point RS-422 links where the same transceiver pinout supports both directions. In a multi-drop RS-485 network, bias resistors and termination must be designed for the cable length, topology, and number of idle nodes to avoid excessive common-mode loading. The principal design consideration is transceiver direction control. DE and /RE can be managed separately or tied together, but the firmware must avoid asserting the driver while another node is transmitting because multiple drivers can conflict on the shared bus. Keep the bus wiring away from noisy sources, use proper signal and return paths, and verify the termination strategy for the selected data rate. This product record combines verified manufacturer and distributor information with practical replacement, application, and layout guidance. It distinguishes the exact 10Mbps MAX3485ESA+T ordering code from related MAX3485 variants, highlights the available SOIC-8 drop-in choices, and identifies specifications that still require confirmation from the official datasheet.

RFQ İletişim
MAX3485ESA/GG8 - 3.3V 10Mbps RS-485 Transceiver | Analog Devices
MAX3485ESA/GG8

MAX3485ESA/GG8 - 3.3V 10Mbps RS-485 Transceiver | Analog Devices

The Analog Devices MAX3485ESA/GG8 is a 3.3 V, low-power, half-duplex RS-485 and RS-422 transceiver rated for data rates up to 10 Mbps in an 8-pin SOIC package. Each device integrates one driver and one receiver, allowing a compact node to support bidirectional communication over a differential bus. Its slew-rate-limited driver is designed to reduce unwanted signal transitions, electromagnetic interference, and cable reflections associated with faster edge rates. The transceiver is suited to industrial equipment, data acquisition systems, building controls, and long-distance serial networks. An RS-485 transceiver is an interface IC that converts logic-level signals into differential differential-pair voltages for reliable communication over noisy or long cables. It also converts received differential signals back into CMOS-compatible logic. The MAX3485 family occupies the interface IC layer within communication systems and combines a line driver, line receiver, and bus-management functions in one package. Its 3.3 V supply supports compact industrial, instrumentation, and embedded-control designs operating from modern low-voltage logic rails. Key operating characteristics include 3.3 V power, a maximum data rate of 10 Mbps, one driver and one receiver, and an 8-pin SOIC footprint. The MAX3485ESA/GG8 is identified as the manufacturer’s extended-temperature part ordering code. The product family description also identifies low-power operation and thermal protection. These characteristics make the device useful where space, bus speed, reduced edge-rate emissions, and dependable differential signaling are more important than integrating multiple protocol-specific interface functions. The integrated driver and receiver support half-duplex RS-485 networks in which a node transmits and receives on the same pair. RS-422 systems can also use the driver and receiver, although the two protocols have different network topologies and driver-enable expectations. The differential signal method improves noise immunity because the receiver evaluates the voltage difference between the two conductors rather than relying on a single conductor referenced only to ground. That principle is especially valuable around motors, relays, switching supplies, and long cables. Typical uses include multi-drop industrial measurement buses, factory-floor controllers, building automation nodes, instrument interfaces, and embedded serial links between a controller and a remote sensor or actuator. A bus may accommodate as many as 256 devices when the complete system is designed for that population, including appropriate termination, biasing, cable length, topology, and data-rate limits. Device count alone does not guarantee successful communication because the complete bus topology must satisfy the selected transceiver’s electrical requirements. The principal design consideration is the relationship between data rate, cable length, topology, termination, and driver edge rate. Keep the differential route compact, use a continuous ground reference where system architecture permits, place termination only at the physical ends of the bus, and verify the driver-enable timing in half-duplex designs. This page consolidates the device’s operating characteristics, package information, application guidance, pinout-status disclosure, and a verified functional-equivalent candidate to support faster engineering review.

RFQ İletişim
MAX3488AEASA+T - 3.3V 20Mbps RS-485/RS-422 Transceiver
MAX3488AEASA+T

MAX3488AEASA+T - 3.3V 20Mbps RS-485/RS-422 Transceiver

The Analog Devices MAX3488AEASA+T is a 3.3V, low-power RS-485 and RS-422 transceiver containing one driver and one receiver. The device supports data rates up to 20Mbps, provides 20kV ESD protection, and uses slew-rate-limited operation to reduce unwanted transmitter-edge effects. It is packaged in an 8-pin SOIC and is identified with the A-grade, narrow-temperature, tape-and-reel ordering code MAX3488AEASA+T. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and converts received differential signals back into CMOS-compatible logic. It belongs to the broader hierarchy of interface transceiver, communications interface, and semiconductor devices. Balanced differential signaling is widely used in industrial control, instrumentation, building automation, and data-communication systems because it improves noise immunity and permits reliable transmission over longer cables than single-ended interfaces. The MAX3488 family combines a reduced-voltage 3.3V supply with high-speed RS-485 and RS-422 operation. Its slew-rate-limited driver limits the rate at which output transitions occur, which helps control edge-generated EMI and reduces the possibility of unwanted reflections on poorly terminated interconnects. The 20kV ESD rating strengthens its suitability for interfaces exposed to electrostatic discharge in industrial and communications equipment. Each device integrates one driver and one receiver, allowing a compact node implementation with both transmit and receive paths. The driver converts a differential logic input into balanced driver outputs, while the receiver converts a differential input into a single-ended receiver output. Because the MAX3488 supports both RS-485 and RS-422 applications, design decisions involving bus topology, termination, grounding, and driver enable control remain central to successful deployment. Typical uses include industrial sensor gateways, programmable logic controller communication, motor-control equipment, data acquisition units, building-automation controllers, and isolated supervisory-control equipment. The 8-pin SOIC footprint simplifies assembly in conventional surface-mount production and provides a practical transition from higher-voltage interface designs to a 3.3V system supply. Designers should confirm the exact receiver threshold, driver enable timing, common-mode limits, and package pin assignments in the manufacturer datasheet before final routing. Termination strategy must be selected for the cable length, topology, and signal rate. Keep the differential pair routed with continuous reference, minimize stubs, and place termination components where the signal can be physically disconnected during testing. This product page combines the exact orderable part number, family-level electrical characteristics, package information, application guidance, design notes, and clearly qualified replacement analysis to support faster component selection and PCB planning.

RFQ İletişim
MAX3488AEGSA+T 20Mbps RS-485 Transceiver | Analog Devices
MAX3488AEGSA+T

MAX3488AEGSA+T 20Mbps RS-485 Transceiver | Analog Devices

The Analog Devices MAX3488AEGSA+T is a 3.3 V-powered RS-485/RS-422 interface transceiver with a maximum data rate of 20 Mbps, ±20 kV ESD protection, and slew-rate-limited drivers. It is packaged in an 8-pin SOIC and uses a +T suffix for tape-and-reel ordering. The device provides one driver and one receiver for bidirectional differential bus communication. An RS-485 transceiver is an interface IC that converts logic-level signals into differential RS-485 signals and converts received differential signals back into CMOS-compatible digital levels. Within the interface hierarchy, MAX3488AEGSA+T belongs to the RS-485/RS-422 transceiver class, which supports longer cables and greater noise immunity than single-ended communication. It is used where robust point-to-point or multipoint data links are required. The 3.3 V supply operation suits modern industrial, telecommunications, and embedded control systems. Its 20 Mbps maximum signaling rate supports faster industrial links than the lower-rate members of the MAX348x family. The ±20 kV ESD rating protects exposed bus pins from electrostatic discharge, while slew-rate-limited operation reduces high-frequency EMI and edge-rate stress associated with rapidly switching cable drivers. Each device contains a differential driver and a differential receiver. The receiver can typically operate with a logic-level enable control, while the transmitter uses a separate enable control for bus-direction management. This arrangement permits a compact interface containing both signaling directions without relying on an external transceiver. The SOIC-8 package also provides a standard surface-mount footprint suitable for production PCB assembly. Typical applications include industrial-control networks, factory automation equipment, telecommunications equipment, instrumentation links, and EMI-sensitive RS-485 or RS-422 buses. The MAX3488AEGSA+T is particularly appropriate when the design requires a low-voltage 3.3 V interface, high maximum data rate, and enhanced ESD protection without introducing a separate external protection network for every exposed bus terminal. Designers should follow the manufacturer's pin-description and application-circuit guidance when assigning driver-enable and receiver-enable functions. The PCB should preserve a continuous return path between the transceiver and connector ground, and external protection or termination components should be selected according to cable length, topology, data rate, and grounding requirements rather than inferred from the transceiver's ESD rating alone. This product page combines the manufacturer's interface description, exact orderable MPN information, package details, application guidance, parameter comparisons, and practical PCB considerations into a design-oriented reference. It highlights where the MAX3488AEGSA+T fits within the MAX348x transceiver family and the engineering checks that should be completed before assigning it to a new RS-485 or RS-422 link.

RFQ İletişim