Ürünler (44.000+)

MAX3488CPA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver
MAX3488CPA+

MAX3488CPA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver

The Analog Devices MAX3488CPA+ is a 3.3V-powered, slew-rate-limited RS-485/RS-422 interface transceiver with one transmitter and one receiver, a 10Mbps maximum data rate, and an 8-pin PDIP package. The verified product information identifies the device as a single transceiver for full-duplex or half-duplex point-to-point and multidrop communication, depending on wiring and termination. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into differential bus signals and receives differential bus signals back into logic levels. These differential interfaces are used where noise immunity, ground-offset tolerance, and reliable multi-drop communication are more important than single-ended signaling. The MAX3488CPA+ is specifically positioned as a low-power, 3.3V device for industrial, communications, and embedded control systems. Verified specifications include 3.3V single-supply operation, one driver, one receiver, 10Mbps capability, and slew-rate-limited operation intended to reduce EMI and reflections from improperly terminated cables. The verified data also describes interoperability with +5V logic. The 8-pin PDIP package provides through-hole construction for designs that favor socketed, leaded components or straightforward prototype assembly. Its transceiver architecture supports RS-485 and RS-422 signaling while remaining distinct from RS-232 transceivers. Typical uses include industrial control links, sensor and actuator networks, building automation, point-of-sale equipment, instrumentation, and embedded serial buses. In a half-duplex RS-485 network, transceiver direction control determines whether the transmitter or receiver is active. In an RS-422 point-to-point arrangement, the transmitter and receiver may operate independently, subject to the complete circuit configuration. Designers should verify supply tolerance, driver and receiver enable requirements, bus termination, biasing, isolation strategy, grounding, and cable length against the manufacturer datasheet. Slew-rate limiting helps control edge energy and ringing, but it does not remove the need for correct topology, termination, and decoupling. Before production substitution, compare the complete pinout, electrical limits, temperature grade, and package dimensions. This product data consolidates verified manufacturer and distributor information, interface-class context, application guidance, and strict replacement constraints. It is intended to support engineering selection while separating verified facts from parameters that require confirmation in the full manufacturer datasheet.

RFQ İletişim
MAX3488CSA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3488CSA+

MAX3488CSA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3488CSA+ is a 3.3 V powered, one-driver and one-receiver RS-485/RS-422 transceiver rated for data rates up to 10 Mbps, with slew-rate limiting for reduced electromagnetic interference and reflections. It is supplied in an 8-pin NSOIC package. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential line signals and converts received differential signals back into logic levels. The MAX3488 family belongs to the physical-layer transceiver hierarchy: RS-485/RS-422 interface -> differential line driver and receiver -> industrial communication and data-conversion semiconductor. Key features include a 3.3 V power supply, one transmit driver, one receive receiver, operation across RS-485 and RS-422 systems, and a maximum data rate of 10 Mbps. Its slew-rate-limited driver is intended to reduce EMI and cable-reflection problems compared with an unrestricted high-speed edge rate. The part is identified as a low-power, 3.3 V family member and is offered with an 8-pin NSOIC package. The device is suitable for point-to-point RS-422 links and multidrop RS-485 networks where the system designer must control bus topology, cable length, termination, and grounding. The receiver provides the differential input path needed for robust communication over industrial cables, while the driver supplies the balanced output used by the bus. Application-specific timing, logic levels, protection requirements, and maximum bus loading must still be checked against the manufacturer datasheet. Typical uses include industrial control links, sensor networks, building automation equipment, test and measurement instruments, data acquisition systems, and embedded serial interfaces. In a practical design, the transceiver should be placed near the connector, the differential pair should be routed with controlled impedance, and the cable-end termination should be installed only where the bus configuration requires it. The principal design consideration is that MAX3488CSA+ is a communication interface, not a complete UART or isolated transceiver. External logic, grounding, protection devices, and application-specific termination may be required. Verify the complete bus specification, cable length, grounding strategy, and ESD requirements before releasing a production PCB. This page consolidates verified manufacturer and distributor information, package details, application guidance, and design notes to support component selection, PCB integration, and drop-in replacement evaluation without extending beyond the supplied data.

RFQ İletişim
MAX3488CSA+T - 10Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3488CSA+T

MAX3488CSA+T - 10Mbps RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX3488CSA+T is a 3.3V-powered RS-485/RS-422 interface transceiver with one driver and one receiver, 10Mbps data-rate capability, slew-rate-limited signaling, and an 8-pin SOIC package. It is designed for bidirectional industrial and instrumentation links where low-power 3.3V operation, reduced electromagnetic interference, and tolerance of imperfect cable termination are important. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus voltages and receives differential bus signals as logic-level data. In the broader semiconductor hierarchy, it belongs to the interface IC class and connects digital controllers to physically longer, noise-prone industrial communication networks. Its differential signaling improves common-mode rejection and allows reliable communication over cables where single-ended signaling would be more susceptible to interference. The MAX3488 combines a low-power 3.3V supply with a 10Mbps maximum data rate. Its slew-rate-limited driver reduces EMI and reflections associated with improperly terminated RS-485 cables, while the receiver provides a practical path to high-speed data transfer. The device is offered in an 8-pin SOIC package for surface-mount assembly, and the CSA+T ordering code identifies the tape-and-reel production configuration. The MAX3488 family includes devices intended for related RS-485 and RS-422 requirements, but speed and operating-temperature choices remain important during substitution. Some family members are optimized for lower data rates, while others target different environmental ranges or common-mode performance. For that reason, an alternative should be checked against the required bus rate, supply voltage, logic levels, termination strategy, and operating-temperature range rather than selected from the package name alone. Typical uses include industrial serial links, programmable-logic controllers, test equipment, building automation, data acquisition systems, and embedded control boards. The 10Mbps capability is useful for factory links, while the 3.3V supply operation aligns with modern controller and digital logic rails. The 1/1 driver-receiver arrangement supports one communication channel per device. A robust implementation requires correct logic-family interfacing, a bypass capacitor near the supply pin, a controlled ground-return path, and termination appropriate to the cable topology. Designers should also evaluate the transceiver's bus loading and common-mode limits against the longest cable and highest-noise operating condition. Slew-rate control reduces edge energy, but it does not replace correct topology, grounding, and cable-length planning. This product page consolidates the manufacturer's device characteristics, sourcing guidance, compatible alternatives, and practical interface-design considerations into a single engineering-focused reference for evaluating the MAX3488CSA+T in 3.3V RS-485 and RS-422 systems.

RFQ İletişim
MAX3488ECPA+ - 12Mbps 3.3V RS-485/RS-422 | Analog Devices
MAX3488ECPA+

MAX3488ECPA+ - 12Mbps 3.3V RS-485/RS-422 | Analog Devices

Analog Devices MAX3488ECPA+ is a 3.3 V-powered RS-485/RS-422 interface transceiver with one driver and one receiver, 12 Mbps data rate, ±15 kV ESD protection, and an 8-pin PDIP package. It is designed for compact, board-level serial interfaces where both RS-485 and RS-422 operation, low supply voltage, and robust electrostatic-discharge protection are required. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level signals into balanced differential signals and receives differential signals back into logic-level data. The MAX3488E belongs to the transceiver hierarchy: transceiver > bus-line transceiver > differential interface IC > interface IC > semiconductor. Its dual differential implementation supports point-to-point RS-422 links as well as multi-drop RS-485 buses, subject to proper termination and biasing. The device operates from a 3.3 V supply and supports data rates up to 12 Mbps. According to the supplied distributor and manufacturer data, the MAX3488ECPA+ provides ±15 kV ESD protection and slew-rate-limited operation. These characteristics are useful in industrial, instrumentation, and embedded communication systems where connector exposure, reflected bus signals, or electromagnetic interference could otherwise corrupt transmitted data. The MAX3488E architecture combines one transmit channel with one receive channel in a single package. Slew-rate limiting controls the transition rate of the driver output, helping reduce unwanted high-frequency content on the bus. This is important in multi-drop RS-485 networks because the transceiver's edge rate directly affects signal integrity, electromagnetic emissions, and receiver performance. Typical uses include industrial control links, RS-485 sensor buses, RS-422 point-to-point equipment links, building automation interfaces, test and measurement equipment, and industrial data acquisition systems. The 8-pin PDIP package is particularly useful for through-hole designs, prototypes, legacy control boards, and applications where a socketed or leaded package simplifies inspection and assembly. A robust implementation must include correct bus termination, fail-safe biasing where required, grounding, and protection appropriate to the installation environment. Supply decoupling should be placed close to the IC, while the differential route should be kept short and symmetrical. Signal integrity and ESD performance depend on the complete board and cable system, not only on the transceiver specifications. This product page consolidates the verified 3.3 V supply, 12 Mbps data rate, ±15 kV ESD protection, RS-485/RS-422 capability, PDIP-8 packaging, distributor pricing, and documented same-family alternatives. It also adds practical PCB guidance and explicit parameter comparisons to support sourcing and engineering decisions.

RFQ İletişim
MAX3488ECSA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3488ECSA+

MAX3488ECSA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3488ECSA+ is a 3.3 V RS-485/RS-422 transceiver with a maximum data rate of 12 Mbps, ±15 kV ESD protection, and an 8-pin NSOIC package. The device combines one driver and one receiver, while its slew-rate-limited driver reduces electromagnetic interference and reflections associated with improperly terminated cables. These characteristics make it suitable for industrial instrumentation, building controls, data acquisition, and noise-sensitive serial communication systems. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential signals and receives differential signals back as logic-level data. The MAX3488ECSA+ belongs to the transceiver hierarchy alongside RS-485 and RS-422 interface ICs, where balanced signaling improves noise immunity and allows communication over longer cables than a single-ended interface. Its true transceiver architecture supports half-duplex or point-to-point differential communication when configured correctly in the target system. The principal features include operation from a 3.3 V supply, ±15 kV ESD protection on the communication pins, a maximum signaling rate of 12 Mbps, and slew-rate-limited operation. The low-power design is intended to reduce system power consumption while retaining the bandwidth needed for industrial and control networks. The MAX3488 family is specifically identified by Analog Devices as a production family, indicating that the MAX3488ECSA+ remains part of the active product line. Slew-rate limiting is the key electrical feature for robust field-bus communication. By controlling the driver edge rate, the MAX3488ECSA+ reduces high-frequency EMI and lowers the likelihood of signal reflections on imperfectly terminated cables. The 12 Mbps maximum data rate supports high-speed data links, although actual bus length, cable impedance, topology, termination, and transceiver enable timing can limit the usable rate in a practical installation. Typical uses include industrial automation controllers, PLC serial interfaces, sensor and actuator networks, building-management equipment, and isolated or non-isolated data-acquisition systems. The device can also connect MCU-based control boards to differential bus nodes when its driver and receiver pins, enable controls, grounding, and termination are assigned according to the manufacturer's pin and application guidance. A critical implementation consideration is bus termination. Place the correct termination network at the physical ends of the RS-485 or RS-422 bus, and keep the driver disabled while the receiver is active unless the network architecture explicitly supports both functions simultaneously. Validate signal polarity and enable timing to prevent contention on the driver outputs. This product page combines the manufacturer's core electrical specifications, practical interface guidance, application use cases, and confirmed pin-compatible alternatives. It also highlights the differences that matter when reviewing a MAX3488ECSA+ replacement for an existing 8-pin NSOIC circuit-board layout.

RFQ İletişim
MAX3488ECSA+T - 3.3V 12Mbps RS-485/RS-422 Transceiver | ADI
MAX3488ECSA+T

MAX3488ECSA+T - 3.3V 12Mbps RS-485/RS-422 Transceiver | ADI

The Analog Devices MAX3488ECSA+T is a 3.3 V RS-485/RS-422 interface IC with one driver and one receiver, 12 Mbps maximum data rate, ±15 kV ESD protection, and slew-rate-limited true transceivers in an 8-pin SOIC package. The MAX3488ECSA+T combines a differential bus driver and differential receiver for bidirectional or point-to-multipoint serial links. An RS-485/RS-422 transceiver is an interface IC that converts between single-ended logic signals and differential physical-layer signals. RS-485 supports balanced, multipoint communication over relatively long cables, while RS-422 emphasizes balanced point-to-point connections. Both standards belong to the broader wired data-communication and interface-IC hierarchy, where noise immunity, common-mode tolerance, cable termination, and signal integrity determine reliable link performance. Key features include operation from a single 3.3 V supply, data rates up to 12 Mbps, ±15 kV ESD protection, and slew-rate-limited driver outputs. The slew-rate limitation reduces high-frequency EMI and helps limit reflections on improperly terminated cables. Each device contains one driver and one receiver, making it suitable for half-duplex RS-485 networks as well as full-duplex RS-422 links when the relevant driver and receiver pins are connected appropriately. The MAX3488 family is positioned for industrial control, instrumentation, building automation, test equipment, and embedded communications where differential signaling is preferred over single-ended interfaces. Its low-power 3.3 V operation can simplify interfaces with modern processors and field-programmable logic. The ±15 kV protection rating improves robustness at connector-exposed bus pins, although protection ratings do not eliminate the need for correct grounding, routing, and surge-protection design. For PCB implementation, use the manufacturer pin-description table to assign the driver input, receiver output, enable controls, differential bus terminals, supply, and ground. Place bypass capacitance close to the supply pins, route the differential pair as a tightly coupled pair, and keep bus-side traces away from sensitive digital and analog paths. External termination and biasing resistors depend on cable length, topology, node count, and whether the bus is idle. This page organizes the electrical characteristics, package details, drop-in candidates, and application guidance needed for initial design review. It also highlights the distinctions engineers should verify before PCB release, especially enable polarity, receiver thresholds, thermal limits, cable termination, and production ordering options.

RFQ İletişim
MAX3488EEPA+ - 12Mbps RS-485/422 Transceiver | Analog Devices
MAX3488EEPA+

MAX3488EEPA+ - 12Mbps RS-485/422 Transceiver | Analog Devices

The Analog Devices MAX3488EEPA+ is a 3.3V-powered, 12Mbps RS-485/RS-422 interface transceiver with ±15kV ESD protection, slew-rate-limited true RS-485/RS-422 operation, and an 8-pin PDIP package. The device combines one driver and one receiver for full-duplex point-to-point communications over balanced cabling. An RS-485/RS-422 transceiver is a differential interface IC used to connect digital logic to industrial communication networks. These interfaces use differential signaling to improve noise immunity and reject common-mode interference. The MAX3488EEPA+ belongs to the transceiver hierarchy of interface ICs, where its driver converts logic-level signals into balanced differential outputs and its receiver converts differential inputs into complementary logic outputs. The principal operating specifications are a 3.3V supply, 12Mbps maximum signaling rate, and ±15kV ESD protection. Its slew-rate-limited driver reduces high-frequency transitions on the bus, which can help limit electromagnetic interference and reflections associated with improperly terminated cables. The package is an 8-pin PDIP, providing a through-hole footprint for industrial-control, instrumentation, and communications equipment. The MAX3488E family combines low-power 3.3V operation with high-speed differential signaling. The E suffix identifies the enhanced ESD-protected family, while the exact temperature range and operating limits must be confirmed in the manufacturer data sheet for each ordering code. Its one-driver, one-receiver arrangement supports full-duplex RS-422 links and multi-driver RS-485-compatible networks when system-level bus arbitration, termination, and grounding are implemented correctly. Typical uses include industrial automation links, data-acquisition systems, building controls, test equipment, and embedded serial networks. The 12Mbps capability suits short, point-to-point or properly terminated balanced connections, while the slew-rate-limited output helps reduce EMI in cabinet-mounted systems. Designers should still evaluate cable length, topology, termination, and ground potential because transceiver speed alone does not determine reliable bus distance. For PCB implementation, place the transceiver close to the connector and route the differential pair as a tightly coupled pair over a continuous reference plane. Add the required bus termination at appropriate physical endpoints and provide low-impedance connections between the interface ground and the equipment ground. Disable unused driver and receiver paths where appropriate to avoid an active output driving the network unnecessarily. This page combines the verified manufacturer and distributor information with practical interface-design guidance, transparent pricing context, and clearly qualified replacement analysis. It distinguishes confirmed drop-in variants from lower-information package alternatives rather than presenting every electrically similar device as a safe PCB replacement.

RFQ İletişim
MAX3488EESA+ - 12Mbps RS-485/422 IC | Maxim Integrated
MAX3488EESA+

MAX3488EESA+ - 12Mbps RS-485/422 IC | Maxim Integrated

Maxim Integrated MAX3488EESA+ is a 3.3V-powered, slew-rate-limited RS-485/RS-422 transceiver with one driver, one receiver, 12Mbps maximum data rate, and ±15kV ESD protection in an 8-pin SOIC package. The MAX3488EESA+ combines true differential bus operation with low-power 3.3V design, making it appropriate for industrial control, instrumentation, data acquisition, and communication equipment operating over longer cables than conventional single-ended interfaces. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential signals for reliable data transmission over wired networks. RS-485 supports multi-drop buses and common-mode noise rejection, while RS-422 provides a point-to-point differential interface with strong drive capability. The MAX3488EESA+ supports both standards and functions as a half-duplex interface with one driver and one receiver, allowing a system to transmit and receive data over a shared pair of conductors. The device operates from a 3.3V supply and provides ±15kV ESD protection on its bus-facing pins. Its slew-rate-limited driver reduces high-frequency harmonics, electromagnetic interference, and cable reflections caused by poor impedance matching. The manufacturer describes the MAX3488 family as low-power, 3.3V transceivers intended to minimize electromagnetic emissions and enable error-free communication at data rates up to 250kbps when conservative slew-rate-limited operation is used. Faster operation up to 12Mbps is available for appropriately terminated point-to-point links. The MAX3488EESA+ uses a differential driver and differential receiver architecture to reject common-mode voltage present on industrial wiring. Its driver produces complementary differential outputs, while the receiver responds to the voltage difference between the bus pair. This architecture supports robust links between a controller, sensor, converter, or data-acquisition module and a remote system. Because the interface is half duplex, software or hardware flow control is needed when the same pair carries both transmit and receive signals. Typical uses include industrial sensor networks, motor-control equipment, PLC peripheral interfaces, factory data buses, instrumentation, building automation, and remote-control links. The 8-pin SOIC package simplifies assembly for conventional PCB designs and supports automated production. The low 3.3V operating voltage also allows direct interfacing with 3.3V microcontrollers, DSPs, and programmable logic when their I/O levels are compatible with the transceiver thresholds. Designers should verify the exact driver, receiver, ground, and supply connections in the pin-description table before routing the PCB. Place the transceiver close to the cable connector, provide a solid ground reference, use proper differential pair routing, and install the protection network recommended by the manufacturer. Cabling, topology, termination, and grounding can be more important than nominal logic speed in determining field reliability. This product resource summarizes the MAX3488EESA+ electrical identity, package, application fit, and compatible interface options. It also highlights practical bus-layout and ESD-protection considerations that help engineers compare the device against other 3.3V RS-485/422 transceivers before committing to a PCB footprint.

RFQ İletişim
MAX3488EESA+T - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3488EESA+T

MAX3488EESA+T - 12Mbps RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX3488EESA+T is a 3.3 V powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, 12 Mbps maximum data rate, ±15 kV ESD protection, and slew-rate-limited signaling. The device is supplied in an 8-pin SOIC package and is configured for 3 V to 3.6 V operation. Its transceiver architecture supports bidirectional point-to-point and multidrop industrial communication links. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential signals and reconstructs logic-level data from received differential signals. Within the interface hierarchy, this device combines an RS-485/RS-422 line driver, a line receiver, ESD protection, and slew-rate control in one semiconductor package. It supports the physical layer used by industrial automation, building controls, instrumentation, and data-acquisition equipment. The MAX3488EESA+T provides a 12 Mbps data rate, ±15 kV ESD-protected inputs, and a slew-rate-limited driver. The low-power 3.3 V design supports systems in which transceiver power must remain compatible with modern digital logic. One driver and one receiver per package make the device appropriate for half-duplex buses that share a physical cable pair, subject to the operating requirements of the selected network topology. Slew-rate limitation reduces the high-frequency content of transmitted transitions, helping limit electromagnetic interference and reflections on cables that may not be perfectly terminated. The integrated ESD protection is a major system-level benefit for field-facing equipment because it strengthens the interface against electrostatic discharge encountered during installation, servicing, or connection of external cables. Typical applications include industrial RS-485 control networks, building-automation equipment, factory data acquisition, remote instrumentation, and isolated or non-isolated industrial communication modules. In a multidrop bus, the designer must preserve the transceiver enable state during receive intervals, configure termination correctly, and verify that all connected nodes use compatible data rates and polarity. For a new design, place the MAX3488EESA+T close to the connector and protection network, route the balanced pair as a tightly coupled differential pair, and provide local bypassing. Confirm that the board ground and cable shield strategy meet the grounding requirements of the industrial installation; the transceiver's ESD rating does not replace an external surge or lightning-protection design. This product overview combines the manufacturer's interface description with drop-in family options, package guidance, application examples, and practical PCB considerations. It highlights the MAX3488EESA+T's 3.3 V supply, 12 Mbps speed, ±15 kV ESD protection, and 8-pin SOIC implementation to support faster component selection and first-pass hardware planning.

RFQ İletişim
MAX3488EPA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver
MAX3488EPA+

MAX3488EPA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver

The Analog Devices MAX3488EPA+ is a 3.3 V powered, 10 Mbps, slew-rate-limited true RS-485/RS-422 transceiver with one driver and one receiver, housed in an 8-pin PDIP package. It supports a 3.0 V to 3.6 V supply range and is designed for low-power point-to-point and multidrop serial links. An RS-485/RS-422 transceiver is an interface IC that converts logic-level transmit and receive signals into balanced differential line signals. These differential signals reject common-mode noise and are used for reliable communication over cables, industrial buses, and distributed equipment. The MAX3488EPA+ combines a driver, receiver, and bus-direction control in one compact interface device. The MAX3488EPA+ operates at 10 Mbps and uses slew-rate limiting to reduce unwanted reflections and electromagnetic interference on longer or poorly terminated interconnects. Its 3.3 V supply operation is suitable for modern embedded systems, while the one-driver, one-receiver arrangement supports RS-422 point-to-point links and RS-485 multidrop networks when configured with appropriate bus transceivers. Typical applications include industrial control links, building automation, instrumentation, data acquisition, serial interfaces between microcontrollers and remote sensors, and embedded communication networks. The device is also appropriate where a compact through-hole package simplifies prototyping and repair. Designers should verify supply voltage, termination, biasing, grounding, and logic levels against the system requirements. The verified snippets identify the MAX3488EPA+ as a 3.3 V, 10 Mbps, slew-rate-limited RS-485/RS-422 transceiver, but complete pin-level electrical data and package dimensions should be taken from the manufacturer datasheet before production release. This page combines verified distributor and manufacturer-search information with application guidance and comparison context for engineers evaluating the MAX3488EPA+ interface IC.

RFQ İletişim
MAX3488ESA+ - 3.3V 10Mbps RS-485/RS-422 | Maxim
MAX3488ESA+

MAX3488ESA+ - 3.3V 10Mbps RS-485/RS-422 | Maxim

The Analog Devices MAX3488ESA+ is a 3.3V-powered, slew-rate-limited RS-485/RS-422 transceiver rated for data rates up to 10Mbps in an 8-pin SOIC package. It combines one driver and one receiver in a half-duplex interface arrangement, providing bidirectional half-duplex communication over a differential bus. The verified product information identifies the MAX3488 as a true RS-485/RS-422 transceiver and highlights its low-power 3.3V operation. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into differential differential-pair signals for communication over longer cables or noisy industrial environments. The RS-485 standard is commonly associated with half-duplex multidrop buses, while RS-422 provides differential signaling and can support point-to-point links. The MAX3488 combines these physical-layer functions with integrated driver and receiver circuitry. The principal verified feature is slew-rate limiting, which reduces the rate at which the driver output changes. This can help reduce unwanted reflections and electromagnetic interference on suitably terminated buses. The 10Mbps capability supports higher-speed links than basic 250kbps transceivers, while the low 3.3V supply is appropriate for modern embedded systems. The MAX3488 family also includes related devices, but the specific package and ordering suffix must be checked before substitution. Typical uses include industrial control equipment, sensor networks, building automation, instrumentation, data acquisition, and embedded serial links where differential signaling is required. The MAX3488ESA+ is particularly relevant when a board needs a compact, integrated RS-485 or RS-422 physical-layer solution rather than discrete driver and receiver stages. Designers should verify the complete pinout, supply requirements, driver and receiver enable behavior, bus termination, common-mode limits, and maximum cable length against the manufacturer datasheet before production. Do not infer unverified electrical limits or pin names from a distributor listing.

RFQ İletişim
MAX3488ESA+T - 10Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3488ESA+T

MAX3488ESA+T - 10Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3488ESA+T is a 3.3V-powered RS-485/RS-422 interface transceiver with one driver and one receiver, supporting data rates up to 10Mbps. The device is supplied in an 8-SOIC package measuring 0.154 inches wide and 3.90mm long, with MAX3488ESA+T configurations offered in tape-and-reel packaging. Its slew-rate-limited transmitter is designed to reduce electromagnetic interference and cable reflections while maintaining reliable balanced-data communication. An RS-485/RS-422 transceiver is an interface integrated circuit that converts logic-level signals into differential bus levels and receives differential bus signals back into logic-level outputs. The MAX3488 belongs to the RS-485 transceiver hierarchy, which also includes half-duplex and full-duplex bus interface devices used in industrial automation, communications equipment, instrumentation, and embedded control systems. RS-422 commonly supports point-to-point links, while RS-485 allows multiple nodes on a shared bus. Key verified features include a 3V to 3.6V supply range, one transmitter and one receiver, support for both RS-422 and RS-485 protocols, and operation at data rates up to 10Mbps. The slew-rate-limited driver is specifically intended to minimize EMI and reduce reflections caused by improperly terminated cables. An extended variant identified as MAX3488E is listed with ±15kV ESD protection and a 12Mbps maximum data rate, but those extended ratings should not be assumed for the ESA suffix without confirmation from the manufacturer. The MAX3488 family combines low-power 3.3V operation with a differential bus interface. The verified distributor data identifies MAX3488ESA+ as a full RS-422/RS-485 transceiver in an 8-SOIC package. Different family members provide distinct combinations of operating speed, supply range, and full-duplex versus half-duplex behavior, so an engineer should compare pin functions and electrical limits rather than relying only on the family name when making a drop-in substitution. Typical applications include industrial RS-485 links, factory automation controllers, building-control equipment, instrumentation gateways, and embedded serial communications modules. In these systems, the transceiver can interface a microcontroller UART to a balanced bus while the slew-rate-limited output helps control edge-rate-induced EMI. Board design must still provide correct bus topology, termination, grounding, and protection appropriate to the installation environment. A key design consideration is that the MAX3488ESA+T operates from a 3V to 3.6V supply, so its logic levels and interface limits must be compatible with the connected processor. Designers should also distinguish the standard MAX3488 from the MAX3488E extended product because the verified source lists different maximum speeds and ESD protection levels. Tape-and-reel notation identifies the shipping format and should not be treated as a functional difference. This product page combines verified manufacturer and distributor information, packaging details, source-backed technical facts, drop-in replacement analysis, and practical RS-485 design guidance. It also distinguishes confirmed values from parameters that require confirmation from the complete manufacturer datasheet, helping engineers avoid unsupported assumptions during schematic capture and PCB layout.

RFQ İletişim
MAX3490AEGSA+ - 3.3V 20Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3490AEGSA+

MAX3490AEGSA+ - 3.3V 20Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3490AEGSA+ is a 3.3V-powered, full-duplex RS-485/RS-422 transceiver rated for data rates up to 20Mbps, with ±20kV ESD protection in an 8-pin SOIC package. It combines one driver and one receiver for bidirectional point-to-point communication over long cables, including industrial control links, instrumentation, and noisy industrial environments. The low-voltage supply and slew-rate-limited operation make it suitable for systems using modern low-voltage logic and requiring controlled edge rates. An RS-485/RS-422 transceiver is an interface IC that converts digital logic-level signals into differential cable signals and receives differential cable signals back into digital logic. The MAX3490AEGSA+ operates in the voltage-regulator hierarchy of industrial communications: it sits between a host controller, such as a UART or processor, and a physical RS-485 or RS-422 cable. Differential signaling improves noise immunity over longer cable runs and allows reliable communication between separated equipment. The MAX3490AEGSA+ family is designed for 3.3V operation and provides 20Mbps maximum data rate with slew-rate-limited drivers. The ±20kV ESD protection helps improve robustness when cables are exposed to electrostatic discharge during installation or operation. Its full-duplex configuration provides separate transmit and receive paths, which is useful when the design requires continuous communication in both directions rather than a shared half-duplex bus. The device is supplied in an 8-pin SOIC package, allowing direct assembly into conventional surface-mount PCB layouts. The MAX3490AEGSA+ family is identified by Analog Devices as a production 3.3V-powered, slew-rate-limited, true RS-485/RS-422 transceiver. The related MAX3490AE page lists a 10Mbps product family overview, while the MAX3490AEGSA+ listing identifies the 20Mbps-rated version. Typical applications include industrial PLC-to-PLC links, factory-floor data acquisition, building automation, security equipment, and embedded instrumentation. When designing the interface, provide correct termination, biasing, common-mode protection, and cable routing according to the system topology. The differential pair should be routed as a controlled-impedance pair, with protection and ground-return arrangements evaluated for the installation environment. This page combines the manufacturer product information with distributor listings and application-oriented engineering guidance. It also organizes the device's RS-485/RS-422 role, electrical limits, package details, replacement considerations, and practical layout practices into a concise selection reference for engineers.

RFQ İletişim
MAX3490AEGSA+T - 20Mbps RS-485/RS-422 Transceiver | ADI
MAX3490AEGSA+T

MAX3490AEGSA+T - 20Mbps RS-485/RS-422 Transceiver | ADI

The Analog Devices MAX3490AEGSA+T is a 3.3V-powered RS-485/RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 20Mbps, and ±20kV ESD protection, housed in an 8-pin SOIC package. Its slew-rate-limited driver reduces EMI and cable reflections, while true RS-485/RS-422 operation supports robust point-to-point and multidrop communications. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus voltages and converts received differential signals back into digital logic. The differential signaling provides common-mode rejection and noise immunity, making these transceivers useful for industrial control, telecommunications, instrumentation, and data links operating over longer cables than single-ended interfaces. The MAX3490AEGSA+T combines a 3.3V supply with a 20Mbps maximum signaling rate. Its slew-rate-limited output reduces high-frequency harmonics and ringing, which can improve interoperability in systems where cable length, connectors, or imperfect termination create reflections. Integrated ±20kV ESD protection strengthens the interface against electrostatic discharge encountered during installation or handling. Each device contains one transmitter and one receiver, allowing one half-duplex bus node to drive a differential line and receive the corresponding differential bus state. The 8-pin SOIC package supports conventional surface-mount assembly while reducing board area compared with larger transceiver packages. The +T suffix identifies the tape-and-reel ordering form for production handling. Typical uses include industrial-control networks, building automation equipment, telecommunications interfaces, instrumentation links, and EMI-sensitive RS-422 connections. Designers should match the bus topology, cable impedance, termination method, grounding strategy, and logic-level supply requirements before finalizing the system interface. Place the transceiver close to the connector and route the differential pair as a controlled-impedance pair. Keep the driver and receiver grounds consistent with the interface reference plane, and use the manufacturer pin description and application guidance when assigning PCB tracks. The slew-rate-limited output should be evaluated together with maximum cable length and system data rate. This page organizes the manufacturer specifications, interface requirements, comparison points, and practical PCB guidance needed to evaluate the MAX3490AEGSA+T as a 3.3V, 20Mbps RS-485/RS-422 transceiver.

RFQ İletişim
MAX3490CPA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver
MAX3490CPA+

MAX3490CPA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver

The Analog Devices MAX3490CPA+ is a 3.3V-powered, 10Mbps, slew-rate-limited true RS-485/RS-422 transceiver with one driver and one receiver, supplied in an 8-pin PDIP package. It is designed for point-to-point and multidrop industrial data links where low-voltage digital systems must communicate over longer, noise-prone cabling. The verified product data identifies full RS-422 and RS-485 operation, a 1/1 transceiver configuration, and a maximum data rate of 10Mbps. An RS-485/RS-422 transceiver is an interface IC that converts logic-level transmit and receive signals into balanced differential bus signals and back again. Differential signaling improves common-mode noise immunity and allows reliable communication over cables where single-ended logic signals would be more susceptible to interference. The MAX3490CPA+ belongs to the transceiver hierarchy: interface transceiver, RS-485/RS-422 interface, wired-communication semiconductor, and signal-conditioning component. The MAX3490 family includes one driver and one receiver, allowing a node to both transmit and receive data. Its 3.3V operation supports systems powered from modern low-voltage rails, while slew-rate limiting reduces unwanted transmit-edge energy and helps control electromagnetic emissions. The device is also described as a true RS-485/RS-422 interface solution, making it suitable for industrial controls, instrumentation links, and communications equipment. The MAX3490CPA+ is a through-hole PDIP-8 device, which is useful when a design needs socketed assembly, prototype flexibility, or a leaded package rather than a surface-mount footprint. The verified distributor listings identify the package as 8-PDIP or DIP-8, with a 0.300-inch, 7.62mm body. The exact pin assignments, electrical limits, temperature range, termination requirements, and recommended operating conditions should be confirmed in the manufacturer datasheet before layout or production release. Typical applications include industrial RS-485 buses, data acquisition systems, remote sensor interfaces, RS-422 point-to-point links, embedded control networks, and communications equipment operating from a 3.3V rail. In a practical bus, the transceiver connects a controller UART to a twisted-pair network, while external termination and biasing may be required according to the bus topology and system requirements. Keep the differential trace pair short, matched, and away from noisy switching paths. This product page consolidates verified distributor and manufacturer information, current sourcing links, and design context for the MAX3490CPA+. Pricing, availability, lifecycle details, and detailed electrical parameters should be refreshed at the source before purchase because distributor data changes over time.

RFQ İletişim
MAX3490CSA+ - 3.3V 10Mbps RS-422/RS-485 | Analog Devices
MAX3490CSA+

MAX3490CSA+ - 3.3V 10Mbps RS-422/RS-485 | Analog Devices

The Analog Devices MAX3490CSA+ is a 3.3V-powered, 10Mbps RS-422/RS-485 interface transceiver in an 8-pin SOIC package. It combines one driver and one receiver for bidirectional differential data links and supports the low-voltage supply range stated in the manufacturer datasheet. The MAX3490 family is intended for industrial, instrumentation, and embedded communication systems where a compact differential interface is required. An RS-422/RS-485 transceiver is an interface IC that converts between logic-level digital signals and balanced differential signals on a communication bus. RS-422 commonly supports point-to-point, full-duplex links, while RS-485 commonly supports multipoint, half-duplex networks. The MAX3490 combines both interface standards in one device, with separate driver and receiver sections and direction control handled by the host logic. The MAX3490CSA+ is identified as a 3.3V-powered, 10Mbps, slew-rate-limited, true RS-485/RS-422 transceiver. Its low-power 3.3V operation suits modern controller platforms and reduces supply demand compared with legacy 5V interface designs. The 10Mbps capability makes it relevant for factory equipment, data acquisition, industrial controllers, and other systems requiring a higher-speed differential serial interface. The device uses one driver and one receiver, allowing a compact implementation of a full-duplex RS-422 connection or a half-duplex RS-485 connection with external direction control. Differential signaling improves noise immunity over single-ended links and helps support reliable communication over longer cables when the bus is properly terminated and laid out. For RS-485 networks, place termination resistors at the physical ends of the bus, bias the idle differential state appropriately, and keep transceiver stub branches short. For RS-422 links, use the receiver and driver pins associated with the intended full-duplex topology and confirm the manufacturer pin configuration before PCB release. Designers should verify supply voltage, driver enable polarity, receiver enable polarity, common-mode limits, cable length, termination, and transceiver direction timing against the MAX3490 datasheet. This page combines verified manufacturer and distributor information, commercial sourcing context, and practical interface-design guidance for evaluating the MAX3490CSA+.

RFQ İletişim
MAX3490CSA+T 3.3V 10Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3490CSA+T

MAX3490CSA+T 3.3V 10Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3490CSA+T is a 3.3V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, supporting data rates up to 10Mbps in an 8-pin SOIC package. Its low-power architecture is designed for industrial communication links where a compact interface is required for bidirectional serial data. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and converts received differential signals back into logic levels. RS-485 supports multipoint buses with bidirectional communication, while RS-422 provides a point-to-point differential link. The MAX3490CSA+T belongs to the interface IC family within the broader semiconductor and industrial-control hierarchy. Key features include operation from a 3.0V to 3.6V supply, a maximum data rate of 10Mbps, one driver and one receiver, and slew-rate-limited operation for reduced EMI and reflection control. The device also includes short-circuit protection and thermal shutdown according to the manufacturer product information. Its 8-SOIC package supports conventional surface-mount PCB assembly. The MAX3490CSA+T uses true differential RS-485/RS-422 signaling, allowing communication over longer cable runs than single-ended interfaces while improving noise immunity. The receiver supports fail-safe operation when the bus is idle, and the driver places its output in a high-impedance state during thermal shutdown. These characteristics suit industrial controllers, instrumentation, data acquisition systems, and factory automation equipment. Typical applications include industrial sensor networks, RS-485 motor-control links, building automation equipment, test and measurement instruments, and embedded control systems. The 3.3V supply is convenient for systems built around modern low-voltage processors, while the 10Mbps capability supports higher-speed factory and data-acquisition links. For PCB design, place the transceiver close to the connector and route the balanced differential pair as a controlled-impedance pair. Connect the bus termination and biasing components according to the system topology, and keep the ground reference continuous between the transceiver and cable interface. Verify the supply voltage, idle-bus behavior, and cable length before releasing the design. This product page combines the manufacturer’s MAX3490 technical information with practical selection guidance, application positioning, and package-level design considerations. It is intended to help engineers identify the correct transceiver for low-voltage, high-speed RS-485 and RS-422 interfaces without conflating protocol requirements, electrical termination, and PCB layout decisions.

RFQ İletişim
MAX3490ECPA - 12Mbps RS-485 Transceiver | Maxim Integrated
MAX3490ECPA

MAX3490ECPA - 12Mbps RS-485 Transceiver | Maxim Integrated

The Maxim Integrated MAX3490ECPA is a 3.3 V-powered, ±15 kV ESD-protected RS-485/RS-422 transceiver that supports data rates up to 12 Mbps and uses an 8-pin PDIP package. The device combines one driver and one receiver in a single package, with slew-rate-limited operation intended to reduce unwanted signal transitions on unbalanced communication lines. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus voltages and converts received differential voltages back into digital logic. The MAX3490ECPA belongs to the MAX3483E family of low-power transceivers designed for industrial, instrumentation, and data-communication links where both long-distance noise immunity and compact integration are important. The principal operating characteristics include a 3.3 V supply, ±15 kV ESD protection, operation at up to 12 Mbps, and slew-rate-limited true RS-485/RS-422 operation. Its one-driver/one-receiver configuration supports point-to-point and multidrop network arrangements when the bus topology, termination, and grounding strategy are designed correctly. The 8-pin PDIP package also supports conventional through-hole PCB assembly and prototyping. Slew-rate limiting reduces the rate at which the differential driver changes state, limiting high-frequency energy that can couple into adjacent circuitry. This behavior is particularly useful on long cables or in systems where reducing edge-related ringing and crosstalk is more important than maximizing data rate. The device should still be evaluated with the intended cable length, topology, termination network, and grounding arrangement. Typical applications include industrial control networks, instrumentation links, data acquisition systems, building automation equipment, and point-to-point data communications. The MAX3490ECPA is appropriate when the system uses 3.3 V logic, requires integrated transmit and receive functions, and can tolerate the operating-speed limitations of a through-hole PDIP package. For a new design, confirm the exact driver-enable and receiver-enable polarity, supply decoupling, bus termination, and fail-safe behavior against the manufacturer pin description and datasheet before fabrication. Place the device near the bus connector when practical to minimize unprotected trace length and reduce ESD exposure. This product record combines the manufacturer’s family-level functional information, package details, operating characteristics, and practical interface design guidance. It also provides drop-in family alternatives, comparison parameters, and application-focused engineering context to support component selection before schematic capture.

RFQ İletişim
MAX3490ECSA+T - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3490ECSA+T

MAX3490ECSA+T - 12Mbps RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX3490ECSA+T is a 3.3 V powered RS-485/RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 12 Mbps, and ±15 kV ESD protection in an 8-pin SOIC package. The integrated slew-rate-limited driver reduces unwanted ringing and electromagnetic interference on long, point-to-point communication links. An RS-485/RS-422 transceiver is an interface IC that converts between CMOS/TTL logic levels and balanced differential signals. It belongs to the transceiver hierarchy within interface ICs, where differential signaling improves noise immunity and allows reliable communication over longer cable distances than ordinary single-ended logic. The MAX3490E family combines low-power 3.3 V operation, fault-tolerant differential drivers, and enhanced electrostatic-discharge protection for industrial and instrumentation networks. Key features include operation from a single 3.3 V supply, a 12 Mbps maximum signaling rate, ±15 kV ESD protection on the bus pins, and one transmit and one receive channel per device. The partially slew-rate-limited driver helps control edge rates, reducing reflections and radiated emissions on suitable terminated networks. The receiver provides differential input detection for RS-422 links, while the device can also participate in half-duplex RS-485 networks when its direction-control interface is used correctly. The MAX3490E series belongs to the MAX3483E family of low-power transceivers. Its internal architecture combines a differential line driver, a differential receiver, bus-direction logic, and protection structures within one compact package. This integration reduces the number of discrete components required for isolated or non-isolated industrial links while preserving a standardized differential bus interface. Designers must still provide appropriate termination, biasing, protection, and grounding for the selected RS-422 or RS-485 topology. Typical uses include industrial sensor networks, programmable logic controller communication, building-automation equipment, test and measurement instruments, data-acquisition modules, and embedded serial links. It is particularly useful when a compact PCB area, 3.3 V supply, moderate-to-high data rates, and direct-contact ESD robustness are required. The 8-pin SOIC footprint also simplifies assembly in designs already using surface-mount interface components. Design considerations include placing the transceiver close to the connector, maintaining a continuous ground reference between the logic side and the cable interface, and using the termination method appropriate to the topology. Differential pairs should be routed with consistent geometry, while surge or isolation components may be required when the cable leaves the protected enclosure. Verify signal polarity, driver-enable logic, receiver output levels, and supply sequencing before releasing a new PCB. This page combines the manufacturer's product specifications, package and interface guidance, comparison criteria, and practical PCB considerations to support faster engineering evaluation of the MAX3490ECSA+T in industrial communications designs.

RFQ İletişim
MAX3490EEPA+ - 12Mbps RS-485 Transceiver | Analog Devices
MAX3490EEPA+

MAX3490EEPA+ - 12Mbps RS-485 Transceiver | Analog Devices

Analog Devices MAX3490EEPA+ is a 3.3 V-powered, slew-rate-limited RS-485/RS-422 transceiver with a maximum data rate of 12 Mbps and ±15 kV ESD protection, packaged in an 8-pin PDIP. It is designed for industrial, instrumentation, communications, and data-acquisition systems that require a true differential transceiver rather than a single-ended RS-232 interface. An RS-485 transceiver is an interface IC that combines a differential line driver with a differential receiver, allowing information to be transmitted reliably over longer cable runs than a single-ended interface. The MAX3490EEPA+ belongs to the broader hierarchy of interface ICs, communication transceivers, physical-layer devices, and semiconductors. Its differential signaling supports noise-resistant communication between equipment located at different ground potentials. The principal operating characteristics are a 3.3 V supply, a 12 Mbps maximum data rate, ±15 kV ESD protection, and slew-rate-limited outputs. The 12 Mbps capability permits the device to handle high-speed command, control, data, and instrumentation links. Slew-rate limiting reduces the high-frequency content of driver transitions, which helps limit electromagnetic interference and reduces the potential for reflections and data errors on suitable bus layouts. This device supports both RS-485 and RS-422 communication modes. RS-485 is commonly used for multidrop buses connecting multiple nodes, while RS-422 is commonly used for point-to-point or limited-driver configurations. The MAX3490EEPA+ combines these functions in one transceiver package, allowing the same physical interface circuit to be configured according to the system’s grounding and bus topology. Typical uses include industrial control systems, test and measurement equipment, building automation, data-acquisition units, motor-control systems, and industrial communications adapters. The 8-pin PDIP package is also convenient for prototyping and systems assembled through through-hole insertion rather than surface-mount automation. PCB implementation should preserve the transceiver’s high-speed signal integrity. Route the differential bus as a closely coupled pair, terminate the line at appropriate physical endpoints, and avoid adding unnecessary stubs. Place the transceiver close to the connector and keep ground returns short. The manufacturer datasheet remains the controlling reference for pin assignments, supply decoupling, driver enable behavior, receiver enable behavior, and absolute maximum ratings. This product page combines the exact manufacturer and distributor identifiers, separates functionally useful alternatives by package and data rate, and adds implementation guidance for evaluating the MAX3490EEPA+ in a new RS-485 or RS-422 design.

RFQ İletişim
MAX3490EESA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3490EESA+

MAX3490EESA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3490EESA+ is a 3.3 V, single-channel RS-485/RS-422 transceiver with one driver, one receiver, 12 Mbps maximum data rate, and ±15 kV ESD protection in an 8-pin SOIC package. Its slew-rate-limited driver supports reliable point-to-point and multidrop industrial communication while helping reduce cable reflections and electromagnetic interference. The MAX3490EESA+ is identified as a production part by the manufacturer. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential bus signals and converts received differential signals back into logic levels. It belongs to the communication-interface hierarchy: transceiver → RS-485/RS-422 interface IC → interface IC → integrated circuit. These transceivers are designed for longer-distance, noise-resistant data links than single-ended interfaces, making them suitable for industrial equipment, building controls, instrumentation, and long cable runs. The MAX3490EESA+ combines 12 Mbps operation with 3.3 V power operation. Its one-driver, one-receiver arrangement allows a node to transmit and receive data, although the driver and receiver enable functions determine the operating direction. The manufacturer describes the MAX3490E family as slew-rate-limited, true RS-485/RS-422 devices with ±15 kV ESD protection. The 8-pin SOIC package supports compact surface-mount layouts while exposing the standard transceiver functions needed for balanced bus implementations. At the system level, the MAX3490EESA+ bridges a host controller or programmable logic and a differential communication bus. The receiver evaluates the difference between the two bus conductors, providing common-mode rejection for a noise-affected industrial environment. The differential bus also enables ground-potential differences between connected equipment to be tolerated within the interface's specified operating limits. The exact common-mode range, receiver thresholds, and electrical limits must be confirmed in the manufacturer datasheet before final sign-off. Typical uses include industrial control links, factory automation equipment, building-automation nodes, test and measurement systems, and embedded data acquisition. The 12 Mbps capability is useful when a design must transfer short, high-volume data bursts over a modest cable distance rather than operate as a slow long-distance field bus. The part can also pair with isolation or interface components when a design requires galvanic separation, surge protection, or additional bus transceivers. Designers should verify the differential-impedance-controlled trace and cable geometry, provide the bus termination specified by the system architecture, and connect the transceiver reference or common-mode network according to the manufacturer application guidance. Placement near the connector can reduce exposure of sensitive receive paths to radiated and conducted noise. Decoupling should also follow the datasheet recommendations, while ESD protection should be evaluated at the connector rather than assumed to replace an external protection network. This product page consolidates the verified manufacturer, distributor, and cross-reference information with practical selection guidance, packaging details, interface comparisons, and application notes. It is intended to help engineers identify the correct 8-SOIC transceiver while separating documented parameters from values that still require datasheet confirmation.

RFQ İletişim
MAX3490EESA+T - 12Mbps RS-485 Transceiver | Analog Devices
MAX3490EESA+T

MAX3490EESA+T - 12Mbps RS-485 Transceiver | Analog Devices

Analog Devices MAX3490EESA+T is a 3.3V-powered, single-channel RS-485/RS-422 transceiver with one driver and one receiver, supporting data rates up to 12Mbps in an 8-pin SOIC package. The MAX3490E combines true RS-485 and RS-422 operation with slew-rate-limited signaling and ±15kV ESD protection, making it appropriate for industrial communication links where both high throughput and surge robustness are required. An RS-485/RS-422 transceiver is a physical-layer interface integrated circuit that converts logic-level signals into balanced differential bus voltages and converts incoming differential signals back into digital logic. The differential signaling improves common-mode noise immunity and allows reliable data transmission over longer cable runs. Positioned within the hierarchy of interface ICs, communications transceivers, and data-bus interface devices, the MAX3490E supports point-to-point RS-422 links as well as multi-drop RS-485 networks when the bus topology, termination, and biasing are designed correctly. Principal features include a 3.3V supply, a maximum data rate of 12Mbps, ±15kV ESD protection, and slew-rate-limited driver outputs. The EESA variant provides an extended -40°C to +85°C operating range, while the +T suffix identifies the tape-and-reel ordering option. The device also includes a receiver with a fail-safe bias network, which helps determine a defined logic state when the bus is idle, disconnected, or shorted. The MAX3490E architecture uses a differential driver and a differential receiver in one package, reducing board area compared with separate driver and receiver ICs. Slew-rate limiting reduces high-frequency EMI and helps suppress reflections on imperfectly terminated cables. Because the device supports both RS-485 and RS-422 standards, one transceiver can cover point-to-point industrial links, multidrop buses, motor-control networks, and data-acquisition equipment when the appropriate termination and idle-bias components are installed. Typical applications include industrial PLC and factory-automation links, instrumentation buses, motor-driver control interfaces, building-automation equipment, and embedded data-acquisition systems. The 12Mbps capability supports demanding factory and motor-control traffic, while the 3.3V supply simplifies interfacing with modern low-voltage controllers, FPGAs, and microprocessors. Design the bus network carefully: terminate both ends of a long RS-485 cable, avoid star branches, keep stub lengths short, and provide a bias resistor only at one location when the transceiver configuration requires idle biasing. Validate differential swing, common-mode range, isolation requirements, and ESD grounding before releasing the PCB layout.

RFQ İletişim
MAX3490EPA+ - 10Mbps RS-485/RS-422 Transceiver | Analog Devices
MAX3490EPA+

MAX3490EPA+ - 10Mbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices MAX3490EPA+ is a 3.3V-powered, full-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 10Mbps, and an 8-pin PDIP package. It operates from a 3V to 3.6V supply and is designed for low-power industrial communication links. According to the verified product data, the device supports RS-485 and RS-422 interfaces, uses slew-rate-limited signaling, and includes short-circuit and thermal protection on the driver. An RS-485/RS-422 transceiver is an interface IC that converts digital logic-level signals into differential bus signals and converts received differential signals back into CMOS-compatible data. These differential links are used in industrial automation, instrumentation, building controls, and data communications because they are more resistant to common-mode noise than single-ended interfaces. The MAX3490EPA+ belongs to the transceiver class within interface ICs and supports point-to-point or multipoint differential communication architectures. The principal verified features include one driver and one receiver, full duplex operation, a 3V to 3.6V supply range, and operation up to 10Mbps. The MAX3490EPA+ is identified as a true RS-485/RS-422 transceiver, while the slew-rate-limited driver helps control edge rates and reduce unwanted reflections and EMI. The verified distributor listing also identifies the package as 8-pin PDIP and lists the device as a 1/1 transceiver. The device is suited to interfaces where low-voltage digital control communicates with a field bus over a cable. Its 10Mbps capability can support high-speed data transfer, industrial control links, and equipment-to-equipment communication. The driver’s short-circuit current limiting and thermal shutdown protection help protect the output stage when a bus fault or improper termination creates excessive output stress. Applications must still observe the manufacturer’s absolute maximum ratings and recommended external-circuit requirements. For PCB implementation, use the 8-pin PDIP footprint and route the differential bus with controlled impedance when cable length, data rate, or EMI requirements justify it. Keep transceiver supply bypassing close to VCC and GND, connect the receiver and driver interface pins according to the datasheet, and select termination appropriate to the cable topology. The verified operating temperature range is -40°C to 85°C, making the part suitable for industrial temperature environments when the surrounding system requirements are met. This page consolidates verified manufacturer and distributor information, pricing references, interface selection guidance, and practical design notes for engineers evaluating the MAX3490EPA+. It does not infer unverified electrical parameters; unavailable values are explicitly marked for follow-up against the manufacturer datasheet.

RFQ İletişim
MAX3490ESA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver
MAX3490ESA+

MAX3490ESA+ - 3.3V 10Mbps RS-485/RS-422 Transceiver

The Maxim Integrated MAX3490ESA+ is a 3.3V low-power RS-485/RS-422 transceiver with one driver and one receiver, designed for data rates up to 10Mbps and housed in an 8-SOIC package. According to the verified product data, it is slew-rate limited and supports true RS-485 and RS-422 communication. The low 3.3V supply makes it suitable for industrial control, instrumentation, communications, and embedded systems where a compact differential interface is required. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into differential signals for reliable communication over wired networks. In this product category, the transmitter drives a differential bus, while the receiver converts the differential bus voltage back into a logic-level signal. RS-422 commonly supports point-to-point communication, while RS-485 supports multipoint bus arrangements. The MAX3490ESA+ combines these functions in one package, reducing the number of external interface components. The verified listing identifies the MAX3490 family as 3.3V, low-power transceivers for RS-485 and RS-422 communication. The MAX3490 device is listed by Analog Devices as a 3.3V-powered, 10Mbps, slew-rate-limited, true RS-485/RS-422 transceiver. The + suffix denotes the lead-free ordering configuration commonly shown by distributors, while the exact package and suffix conventions should be confirmed against the manufacturer ordering guide before production release. Slew-rate limiting helps control the transition speed of the driver, reducing electromagnetic interference and cable reflections associated with faster edges. This is particularly useful when the transceiver drives longer cables or imperfectly terminated buses. The 10Mbps capability supports high-speed point-to-point links, but cable length, topology, termination, grounding, and signal integrity must be evaluated as a complete system rather than treated as an isolated IC specification. Typical applications include industrial RS-485 links, building and factory automation, data acquisition equipment, motor-control systems, security equipment, and embedded communications modules. The 3.3V supply is convenient for systems using 3.3V microcontrollers, DSPs, FPGAs, or other digital controllers. Designers should verify voltage levels, driver and receiver enable timing, bus termination, protection requirements, and operating-temperature limits against the manufacturer datasheet before release. The primary design consideration is ensuring the transceiver operates within the electrical limits of the intended bus. Differential routing should use controlled impedance where practical, the ground reference should be maintained, and unused inputs should not be left floating. This page combines the verified manufacturer and distributor information with practical application guidance, packaging information, and engineering selection criteria for evaluating the MAX3490ESA+.

RFQ İletişim