AD648KR - Dual Low-Power Precision BiFET Op Amp | Analog Devices
MPN: AD648KR ✗ Son Kullanım ZamanıAD648KR Genel Bakış
A BiFET operational amplifier is an input stage built with field-effect transistors. This low-input-bias architecture places the AD648 in the wider hierarchy of operational amplifier, analog amplifier, and semiconductor. Unlike general-purpose bipolar operational amplifiers, the AD648 is optimized for measuring systems where source leakage, drift, and power consumption can corrupt small signals or limit battery-powered operation.
The AD648 uses ion-implanted FET input devices and laser wafer trimming. Its maximum input offset voltage is 1 mV, maximum offset drift is 2 µV/°C, and maximum output noise is 2 V p-p. Common-mode rejection reaches 82 dB minimum, while the dual 1 MHz amplifiers support precision instrumentation, low-level current measurement, and buffered sensor interfaces.
The AD648KR is offered in the 8-pin SOIC package and is pin compatible with established dual operational amplifiers such as the LF442, TL062, and AD642. Its low quiescent current makes it appropriate for battery-powered equipment, while its input characteristics reduce errors in high-impedance sources. The manufacturer lists the AD648 family as not recommended for new designs, so engineers should assess lifecycle constraints during sourcing decisions.
Typical uses include precision instrument front ends, CMOS DAC buffers, pH and electrochemical sensor interfaces, photodiode signal chains, and low-power sensor conditioning. Each amplifier can operate from dual supplies, and its low input bias current is especially useful when leakage from sensors, guards, or PCB contamination becomes comparable to the measured signal.
The main design consideration is dynamic performance. A 1 MHz unity-gain bandwidth is suitable for precision and low-frequency measurements but is much slower than modern high-speed amplifiers. Confirm source impedance, capacitive loading, required noise bandwidth, supply voltage, and settling behavior before using the device in higher-bandwidth signal chains.
This product page combines manufacturer specifications, lifecycle guidance, pin information, drop-in alternatives, and application-focused design guidance. It also helps engineers distinguish genuine pin-compatible replacements from parts that merely offer similar low-power precision amplifier functions.
Drop-in alternatifler için AD648KR — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller AD648KR (aynı form faktörü ve ayağa oturma) — farklı olan Package, Mounting Type, Amplifier Type, Maximum Input Bias Current, Number of Channels.
AD648KRZ
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
AD642SH
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PIC18LF4420-I/ML
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →TL062
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
AD648S
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
AD648KR Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Type | Dual precision low-power BiFET operational amplifier |
| Number of Channels | 2 channels |
| Unity-Gain Bandwidth | 1 MHz |
| Maximum Input Bias Current | 10 pA max, warmed up |
| Maximum Quiescent Current | 400 µA max |
| Maximum Input Offset Voltage | 1 mV max |
| Maximum Offset Voltage Drift | 2 µV/°C max |
| Maximum Output Noise | 2 V p-p |
| Minimum Common-Mode Rejection | 82 dB |
| Slew Rate | 1 V/µs |
| Paket | 8-pin SOIC, 3.90 mm × 4.90 mm body |
| Montaj Türü | Surface mount |
AD648KR Pin Yapısı
| Pin 1 | OUTA — Output of amplifier A |
| Pin 2 | INA− — Inverting input of amplifier A |
| Pin 3 | INA+ — Noninverting input of amplifier A |
| Pin 4 | V− — Negative supply voltage |
| Pin 5 | INB+ — Noninverting input of amplifier B |
| Pin 6 | INB− — Inverting input of amplifier B |
| Pin 7 | OUTB — Output of amplifier B |
| Pin 8 | V+ — Positive supply voltage |
Tipik Uygulamalar
AD648KR için uygundur 6 uygulamas: Precision Instrument Front Ends, Battery-Powered Sensor Conditioning, CMOS DAC Buffering, Electrochemical and pH Sensors, Photodiode Signal Chains, Low-Power Data Acquisition.
Precision Instrument Front Ends
The AD648KR fits precision instrument front ends that must measure low-level signals while consuming little power. Its maximum input bias current of 10 pA when warmed and maximum input offset voltage of 1 mV reduce errors from high-impedance sources. The two amplifiers can condition differential inputs or form cascaded gain stages around sensor bridges, strain gauges, and laboratory probes. A 1 MHz unity-gain bandwidth is appropriate for precision measurements operating below megahertz signal bandwidth, while the 400 µA maximum quiescent current supports portable instruments. Designers should still verify input common-mode limits, output swing, noise bandwidth, and stability for the selected operating point.
Önerilen
Battery-Powered Sensor Conditioning
The AD648KR is appropriate for battery-powered sensor conditioning because it combines a 400 µA maximum quiescent current with very low input bias current. These characteristics limit the loading imposed on electrochemical, resistive, or capacitive sensors while reducing overall instrument power consumption. The 1 mV maximum input offset and 2 µV/°C maximum drift help preserve measurement stability as supply voltage or temperature changes. Use the device for gain stages near the sensor rather than after long cable runs, and account for the amplifier’s 1 MHz bandwidth when filtering noise and settling. Guard traces and clean dielectrics remain important when the source impedance is high enough for picoamp bias current to matter.
Önerilen
CMOS DAC Buffering
The AD648KR can buffer CMOS DAC outputs where low bias current and low offset error help preserve small-signal accuracy. Its matched dual-amplifier configuration supports two buffered outputs or independent channels, and the low 400 µA maximum quiescent current reduces power overhead in portable equipment. The 1 MHz unity-gain bandwidth is suitable for precision DAC outputs and low-frequency control loops, but the settling behavior and capacitive load capability must be checked at the required frequency. Follow the Analog Devices AD648 data sheet for recommended application circuits and include output isolation where the DAC or downstream load could otherwise violate stability or output-swing conditions.
Önerilen
Electrochemical and pH Sensors
The AD648KR is well matched to electrochemical and pH sensor interfaces because leakage from the sensor, solution, or PCB can create errors comparable to the useful signal. A maximum input bias current of 10 pA when warmed helps limit that error, while the 82 dB minimum common-mode rejection supports rejection of common-mode interference. The amplifier can be configured as a low-noise voltage follower or transimpedance stage around the sensing electrode. Keep input traces short, use guarding where practical, and confirm the actual input bias-current temperature behavior. The 1 MHz bandwidth is more than adequate for many slow electrochemical measurements but should be balanced against noise and stability requirements.
Önerilen
Photodiode Signal Chains
The AD648KR can serve in low-light photodiode measurement chains where input leakage and offset error determine detectability. Its maximum warmed input bias current of 10 pA reduces bias-current-induced error, while the low-power architecture supports portable optical instruments. The dual configuration allows a signal channel and a reference or transimpedance stage, and the 82 dB minimum common-mode rejection helps control coupled interference. Use guarded, short signal paths and low-leakage board materials around the photodiode. The 1 MHz bandwidth is suitable for many precision optical measurements, but total input capacitance, diode capacitance, and feedback stability must be evaluated before increasing bandwidth.
Önerilen
Low-Power Data Acquisition
The AD648KR supports low-power data-acquisition systems requiring two precision analog channels with minimal quiescent-current demand. The 400 µA maximum quiescent current and 10 pA maximum warmed input bias current are valuable when multiplexed sensor inputs include high-impedance sources. Its 1 MHz unity-gain bandwidth can handle signals well beyond many slow industrial measurement channels, although filtering and settling should match the acquisition rate. Two independent channels reduce component count when implementing differential input stages, reference buffers, or programmable gain front ends. Validate the input common-mode range, output swing, settling time, and channel matching for the selected gain and supply configuration.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: AD648KR — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | AD648KRZ | AD642 | AD648S | LF442 | TL062 |
|---|---|---|---|---|---|---|
| Manufacturer | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Linear Technology | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Configuration | Dual precision BiFET operational amplifier | Dual precision BiFET operational amplifier | Dual precision BiFET operational amplifier | Dual precision BiFET operational amplifier | Dual low-power operational amplifier | Dual low-power operational amplifier |
Ana Farklılayıcılar
- Lower power dissipation in compatible dual-amplifier designs (karşılaştırma:LF442)
- Lower power dissipation in compatible dual-amplifier designs (karşılaştırma:TL062)
- Precision BiFET performance with very low bias current (karşılaştırma:AD648KRZ)
- Two precision amplifiers in one 8-pin package (karşılaştırma:AD642)
Tasarım Notları
Do not treat the 8-pin SOIC outline as sufficient proof of replacement compatibility. Before substituting the LF442 or TL062, compare input common-mode range, output swing, offset voltage, bias current, noise, bandwidth, slew rate, and capacitive-load stability at the actual supply voltage. The Analog Devices AD648 data sheet specifically identifies the AD648 as pin compatible with these dual-amplifier families, but the electrical requirements still govern functional equivalence.
Keep the two inputs of each amplifier close together and route them away from power-supply switching nodes and high-current return paths. For high-impedance sources, shorten traces, avoid solder-flux residue near inputs, use guard traces where practical, and select PCB materials with low leakage. The AD648’s maximum warmed input bias current of 10 pA makes leakage control more important than it would be for a conventional bipolar-input precision amplifier.
Set the feedback network according to the selected gain and verify settling before operation at the intended measurement bandwidth. A 1 MHz unity-gain bandwidth can create sensitivity to excess loop gain or source capacitance in follower and transimpedance configurations. Add output isolation for capacitive loads and include the input, output, and bypass capacitors recommended by Analog Devices in the AD648 application circuits.
Uyumluluk Bilgisi
The AD648 is a general-purpose precision operational amplifier rather than an AEC-Q100 automotive-qualified device. Specific material-compliance declarations should be confirmed for the exact ordering code and package.