Analog Devices

AD648KR - Dual Low-Power Precision BiFET Op Amp | Analog Devices

料号: AD648KR ✗ 停产
1 mV max Vdss 10 pA max, warmed up Id 8-pin SOIC, 3.90 mm × 4.90 mm body Package
最小起订量: 1 |

AD648KR 概述

Analog Devices AD648KR is a dual precision, low-power BiFET operational amplifier with a maximum input bias current of 10 pA, a maximum quiescent current of 400 µA, and a 1 MHz unity-gain bandwidth, packaged in an 8-pin SOIC. It combines low offset voltage, low voltage drift, high common-mode rejection, and low 1/f noise for precision analog signal conditioning.

A BiFET operational amplifier is an input stage built with field-effect transistors. This low-input-bias architecture places the AD648 in the wider hierarchy of operational amplifier, analog amplifier, and semiconductor. Unlike general-purpose bipolar operational amplifiers, the AD648 is optimized for measuring systems where source leakage, drift, and power consumption can corrupt small signals or limit battery-powered operation.

The AD648 uses ion-implanted FET input devices and laser wafer trimming. Its maximum input offset voltage is 1 mV, maximum offset drift is 2 µV/°C, and maximum output noise is 2 V p-p. Common-mode rejection reaches 82 dB minimum, while the dual 1 MHz amplifiers support precision instrumentation, low-level current measurement, and buffered sensor interfaces.

The AD648KR is offered in the 8-pin SOIC package and is pin compatible with established dual operational amplifiers such as the LF442, TL062, and AD642. Its low quiescent current makes it appropriate for battery-powered equipment, while its input characteristics reduce errors in high-impedance sources. The manufacturer lists the AD648 family as not recommended for new designs, so engineers should assess lifecycle constraints during sourcing decisions.

Typical uses include precision instrument front ends, CMOS DAC buffers, pH and electrochemical sensor interfaces, photodiode signal chains, and low-power sensor conditioning. Each amplifier can operate from dual supplies, and its low input bias current is especially useful when leakage from sensors, guards, or PCB contamination becomes comparable to the measured signal.

The main design consideration is dynamic performance. A 1 MHz unity-gain bandwidth is suitable for precision and low-frequency measurements but is much slower than modern high-speed amplifiers. Confirm source impedance, capacitive loading, required noise bandwidth, supply voltage, and settling behavior before using the device in higher-bandwidth signal chains.

This product page combines manufacturer specifications, lifecycle guidance, pin information, drop-in alternatives, and application-focused design guidance. It also helps engineers distinguish genuine pin-compatible replacements from parts that merely offer similar low-power precision amplifier functions.

直接替换替代料: AD648KR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: AD648KR (相同外形与封装尺寸) ——差异在于 Package, Mounting Type, Amplifier Type, Maximum Input Bias Current, Number of Channels.

Analog Devices
Package: 8-pin hermetically sealed metal-can TO-99
Mounting Type: Through-hole
Amplifier Type: Precision dual BiFET operational amplifier
对比 AD648KR →
Microchip Technology
Package: 44-QFN (8x8 mm) with exposed pad

AD648KRZ

✅ 直接替换
📦 8-pin SOIC
Same 8-pin SOIC footprint and matching functional characteristics; ordering-code temperature-grade meaning must be checked before use.

📋 参考替代料(不在目录中)

AD642SH

✅ 直接替换
Analog Devices
📦 8-pin SOIC
2 · Precision dual BiFET operational amplifier · 3500 uV · 1 MHz · 35 pA when warmed up · 500 uV maximum · 2 uV p-p · High

联系询价

查看数据手册 →

PIC18LF4420-I/ML

✅ 直接替换
Microchip Technology
📦 8-pin SOIC
PIC 18F · PIC18 8-bit RISC · Flash · 16 KB (8K x 16) · 768 bytes · 256 bytes · 40 MHz · 2.0 V to 5.5 V

联系询价

查看数据手册 →

TL062

✅ 直接替换
📦 8-pin SOIC
Pin-compatible dual amplifier; power dissipation can differ by as much as 85% when replacing the AD648 with the AD648.

📋 参考替代料(不在目录中)

AD648S

✅ 直接替换
📦 8-pin SOIC
Same AD648 electrical family and 8-pin SOIC pin arrangement; package option and ordering-code grade require confirmation.

📋 参考替代料(不在目录中)

AD648KR 最大额定值与电气特性

Amplifier Type Dual precision low-power BiFET operational amplifier
Number of Channels 2 channels
Unity-Gain Bandwidth 1 MHz
Maximum Input Bias Current 10 pA max, warmed up
Maximum Quiescent Current 400 µA max
Maximum Input Offset Voltage 1 mV max
Maximum Offset Voltage Drift 2 µV/°C max
Maximum Output Noise 2 V p-p
Minimum Common-Mode Rejection 82 dB
Slew Rate 1 V/µs
封装 8-pin SOIC, 3.90 mm × 4.90 mm body
安装类型 Surface mount

AD648KR 引脚配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
引脚 1 OUTA — Output of amplifier A
引脚 2 INA− — Inverting input of amplifier A
引脚 3 INA+ — Noninverting input of amplifier A
引脚 4 V− — Negative supply voltage
引脚 5 INB+ — Noninverting input of amplifier B
引脚 6 INB− — Inverting input of amplifier B
引脚 7 OUTB — Output of amplifier B
引脚 8 V+ — Positive supply voltage

典型应用

AD648KR 适用于 6 应用s: Precision Instrument Front Ends, Battery-Powered Sensor Conditioning, CMOS DAC Buffering, Electrochemical and pH Sensors, Photodiode Signal Chains, Low-Power Data Acquisition.

🔧

Precision Instrument Front Ends

The AD648KR fits precision instrument front ends that must measure low-level signals while consuming little power. Its maximum input bias current of 10 pA when warmed and maximum input offset voltage of 1 mV reduce errors from high-impedance sources. The two amplifiers can condition differential inputs or form cascaded gain stages around sensor bridges, strain gauges, and laboratory probes. A 1 MHz unity-gain bandwidth is appropriate for precision measurements operating below megahertz signal bandwidth, while the 400 µA maximum quiescent current supports portable instruments. Designers should still verify input common-mode limits, output swing, noise bandwidth, and stability for the selected operating point.

🔋

Battery-Powered Sensor Conditioning

The AD648KR is appropriate for battery-powered sensor conditioning because it combines a 400 µA maximum quiescent current with very low input bias current. These characteristics limit the loading imposed on electrochemical, resistive, or capacitive sensors while reducing overall instrument power consumption. The 1 mV maximum input offset and 2 µV/°C maximum drift help preserve measurement stability as supply voltage or temperature changes. Use the device for gain stages near the sensor rather than after long cable runs, and account for the amplifier’s 1 MHz bandwidth when filtering noise and settling. Guard traces and clean dielectrics remain important when the source impedance is high enough for picoamp bias current to matter.

📡

CMOS DAC Buffering

The AD648KR can buffer CMOS DAC outputs where low bias current and low offset error help preserve small-signal accuracy. Its matched dual-amplifier configuration supports two buffered outputs or independent channels, and the low 400 µA maximum quiescent current reduces power overhead in portable equipment. The 1 MHz unity-gain bandwidth is suitable for precision DAC outputs and low-frequency control loops, but the settling behavior and capacitive load capability must be checked at the required frequency. Follow the Analog Devices AD648 data sheet for recommended application circuits and include output isolation where the DAC or downstream load could otherwise violate stability or output-swing conditions.

🧪

Electrochemical and pH Sensors

The AD648KR is well matched to electrochemical and pH sensor interfaces because leakage from the sensor, solution, or PCB can create errors comparable to the useful signal. A maximum input bias current of 10 pA when warmed helps limit that error, while the 82 dB minimum common-mode rejection supports rejection of common-mode interference. The amplifier can be configured as a low-noise voltage follower or transimpedance stage around the sensing electrode. Keep input traces short, use guarding where practical, and confirm the actual input bias-current temperature behavior. The 1 MHz bandwidth is more than adequate for many slow electrochemical measurements but should be balanced against noise and stability requirements.

💡

Photodiode Signal Chains

The AD648KR can serve in low-light photodiode measurement chains where input leakage and offset error determine detectability. Its maximum warmed input bias current of 10 pA reduces bias-current-induced error, while the low-power architecture supports portable optical instruments. The dual configuration allows a signal channel and a reference or transimpedance stage, and the 82 dB minimum common-mode rejection helps control coupled interference. Use guarded, short signal paths and low-leakage board materials around the photodiode. The 1 MHz bandwidth is suitable for many precision optical measurements, but total input capacitance, diode capacitance, and feedback stability must be evaluated before increasing bandwidth.

🖥️

Low-Power Data Acquisition

The AD648KR supports low-power data-acquisition systems requiring two precision analog channels with minimal quiescent-current demand. The 400 µA maximum quiescent current and 10 pA maximum warmed input bias current are valuable when multiplexed sensor inputs include high-impedance sources. Its 1 MHz unity-gain bandwidth can handle signals well beyond many slow industrial measurement channels, although filtering and settling should match the acquisition rate. Two independent channels reduce component count when implementing differential input stages, reference buffers, or programmable gain front ends. Validate the input common-mode range, output swing, settling time, and channel matching for the selected gain and supply configuration.

推荐产品汇总

AD648KRZ Same-family SOIC alternative 用于: Precision Instrument Front Ends, Battery-Powered Sensor Conditioning, Electrochemical and pH Sensors, Photodiode Signal Chains AD642 Pin-compatible precision amplifier family 用于: Precision Instrument Front Ends, Electrochemical and pH Sensors, Low-Power Data Acquisition LF442 Pin-compatible low-power dual amplifier 用于: Battery-Powered Sensor Conditioning, Photodiode Signal Chains AD648S Same-family amplifier option 用于: CMOS DAC Buffering, Low-Power Data Acquisition TL062 Pin-compatible dual amplifier family 用于: CMOS DAC Buffering
What is the AD648KR?
The AD648KR is a dual precision, low-power BiFET operational amplifier with a maximum input bias current of 10 pA, a maximum quiescent current of 400 µA, and a 1 MHz unity-gain bandwidth in an 8-pin SOIC package. According to the Analog Devices AD648 data sheet, it is intended for dual-supply applications requiring low power and precise DC and AC performance.
Where can I download the AD648KR datasheet PDF?
The official AD648KR datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/AD648.pdf. The document covers electrical characteristics, pin definitions, typical performance curves, applications, and ordering information for the AD648 family. Use the package and ordering-information sections to confirm the AD648KR suffix and its 8-pin SOIC configuration.
What are the key specifications of AD648KR that engineers should know?
The AD648KR combines a maximum input bias current of 10 pA, maximum quiescent current of 400 µA, 1 MHz unity-gain bandwidth, 1 V/µs slew rate, and 1 mV maximum input offset voltage. According to the Analog Devices AD648 data sheet, it also provides 2 µV/°C maximum offset drift, 82 dB minimum common-mode rejection, and 2 V p-p maximum output noise.
What is the AD648KR pinout?
The AD648KR uses a standard 8-pin SOIC dual-operational-amplifier arrangement: pin 1 is OUTA, pin 2 is INA−, pin 3 is INA+, pin 4 is V−, pin 5 is INB+, pin 6 is INB−, pin 7 is OUTB, and pin 8 is V+. According to the Analog Devices AD648 data sheet, this arrangement is compatible with industry-standard dual operational amplifiers.
Is the AD648KR suitable for low-power instrumentation?
Yes, the AD648KR is suitable for low-power instrumentation because it limits quiescent current to 400 µA max while maintaining 10 pA max input bias current when warmed. According to the Analog Devices AD648 data sheet, the combination reduces source-loading and power-consumption errors in precision instrument front ends and battery-powered measurement systems.
What is the difference between AD648KR and AD648KRZ?
The AD648KR and AD648KRZ are both 8-channel, 8-pin SOIC dual J-FET amplifier solutions associated with the AD648 family. The FindIC comparison identifies AD648KRZ as a complete replacement with consistent terminals, package, and principal performance characteristics. The exact ordering-code and temperature-grade meanings should be confirmed in Analog Devices ordering documentation before substitution.
When should I choose AD648KR over LF442?
Choose the AD648KR when a precision low-power BiFET stage with a specified 10 pA max warmed input bias current, 400 µA max quiescent current, and 1 MHz unity-gain bandwidth is required. The AD648 data sheet states that the AD648 is pin compatible with the LF442 and can reduce power dissipation by as much as 85% for designs that meet the AD648 electrical limits.
When should I choose AD648KR over TL062?
Choose the AD648KR when its specified precision and low-power characteristics better match the signal chain than the TL062. The Analog Devices AD648 data sheet identifies the AD648 as pin compatible with the TL062 and states that the AD648 can reduce power dissipation by up to 85%. Verify input offset, bias current, noise, and bandwidth against the actual operating conditions before replacement.
AD648KR vs AD642: which is better for low-power precision designs?
The AD648KR is the better choice when the required 1 MHz unity-gain bandwidth, 400 µA max quiescent current, and 10 pA max warmed input bias current align with the design. The AD642 appears in the Analog Devices AD648 data sheet as a pin-compatible industry-standard dual operational amplifier. The final choice requires a parameter-by-parameter comparison against the operating voltage, noise bandwidth, and required offset accuracy.
What can replace the AD648KR on an existing PCB?
The AD648KRZ is a direct same-package option, while the AD642, LF442, and TL062 are identified by Analog Devices as pin-compatible dual operational-amplifier families. A valid replacement must match the SOIC footprint, supply arrangement, input common-mode range, output swing, noise, bias current, stability, and temperature requirements rather than relying only on the eight-pin outline.
Can AD648KR replace a TL062 without PCB changes?
Yes, the AD648KR can fit the TL062 pin arrangement according to the Analog Devices AD648 data sheet. Pin compatibility does not guarantee identical performance, so confirm operating-point conditions, input common-mode range, output swing, offset voltage, bias current, noise, and capacitive-load stability before approving the replacement.
Where can I request a quote and current lead time for AD648KR?
Use the Request a Quote form on this page to request current pricing, stock, minimum order quantity, lead time, and delivery details for the AD648KR. The Analog Devices product page marks the AD648 as not recommended for new designs, so procurement planning should account for potential lifecycle constraints and a clearly identified approved second source.
Is the AD648KR in stock?
Current stock should be confirmed through the Request a Quote form on this page because inventory and lifecycle conditions can change independently of the product page. The AD648 family is marked by Analog Devices as not recommended for new designs. For production planning, request the exact AD648KR suffix, quantity, delivery date, and traceability requirements in writing.
What is the price of the AD648KR?
Use the Request a Quote form on this page for the current AD648KR price and quantity schedule. Pricing is maintained as a separate commercial field so that the technical description does not present stale figures. The exact query should include the AD648KR ordering code, required quantity, and any reel, tray, or other delivery requirements.
How does the AD648KR behave with high-impedance sensors?
The AD648KR is well suited to high-impedance sensing because its maximum warmed input bias current is only 10 pA and bias current is guaranteed across the common-mode range. According to the Analog Devices AD648 data sheet, this reduces leakage-induced errors in precision front ends. Board cleanliness, guard-ring design, dielectric absorption, and input capacitance still require careful evaluation.
What lifecycle status does Analog Devices list for AD648KR?
Analog Devices lists the AD648 as not recommended for new designs, which is reflected here as NRND for the AD648KR family ordering code. Existing designs may still require support, but new-product decisions should compare lifecycle risk, availability, and qualified alternatives. Use the Request a Quote form to confirm current supply for the exact ordering code.
Does the AD648KR require special layout for low-noise performance?
Yes, low-noise operation requires attention to source impedance, grounding, input-capacitance management, and leakage around high-impedance nodes. According to the Analog Devices AD648 data sheet, the AD648 reduces output errors in low-level and precision applications. Use short input paths, clean PCB materials, appropriate guarding, and stable reference and bypass layouts.

工程参考数据: AD648KR ——对比、设计指导和合规信息。

选型指南

Choose the AD648KR when a legacy design requires a dual precision BiFET amplifier with a maximum warmed input bias current of 10 pA, maximum quiescent current of 400 µA, and 1 MHz unity-gain bandwidth in an 8-pin SOIC. Choose AD648KRZ when that ordering code better matches the required grade and procurement conditions, after checking temperature-grade terminology. The AD642, LF442, and TL062 are pin-compatible families that can simplify board reuse, but they should be selected only after comparing offset, drift, noise, bandwidth, common-mode range, and power requirements. Because Analog Devices marks the AD648 family as not recommended for new designs, use it primarily for continuity of an existing qualified design unless lifecycle, availability, and long-term support risks have been formally reviewed.

与替代料对比

参数 本产品 AD648KRZ AD642 AD648S LF442 TL062
Manufacturer Analog Devices Analog Devices Analog Devices Analog Devices Linear Technology Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Amplifier Configuration Dual precision BiFET operational amplifier Dual precision BiFET operational amplifier Dual precision BiFET operational amplifier Dual precision BiFET operational amplifier Dual low-power operational amplifier Dual low-power operational amplifier

关键差异点

  • Lower power dissipation in compatible dual-amplifier designs (对比 LF442)
  • Lower power dissipation in compatible dual-amplifier designs (对比 TL062)
  • Precision BiFET performance with very low bias current (对比 AD648KRZ)
  • Two precision amplifiers in one 8-pin package (对比 AD642)

设计说明

Do not treat the 8-pin SOIC outline as sufficient proof of replacement compatibility. Before substituting the LF442 or TL062, compare input common-mode range, output swing, offset voltage, bias current, noise, bandwidth, slew rate, and capacitive-load stability at the actual supply voltage. The Analog Devices AD648 data sheet specifically identifies the AD648 as pin compatible with these dual-amplifier families, but the electrical requirements still govern functional equivalence.

Keep the two inputs of each amplifier close together and route them away from power-supply switching nodes and high-current return paths. For high-impedance sources, shorten traces, avoid solder-flux residue near inputs, use guard traces where practical, and select PCB materials with low leakage. The AD648’s maximum warmed input bias current of 10 pA makes leakage control more important than it would be for a conventional bipolar-input precision amplifier.

Set the feedback network according to the selected gain and verify settling before operation at the intended measurement bandwidth. A 1 MHz unity-gain bandwidth can create sensitivity to excess loop gain or source capacitance in follower and transimpedance configurations. Add output isolation for capacitive loads and include the input, output, and bypass capacitors recommended by Analog Devices in the AD648 application circuits.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The AD648 is a general-purpose precision operational amplifier rather than an AEC-Q100 automotive-qualified device. Specific material-compliance declarations should be confirmed for the exact ordering code and package.

数据核验日期: 2026-11-18 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

AD648KR datasheet AD648KR datasheet pdf AD648KR pinout AD648KR equivalent AD648KR replacement AD648KR cross reference AD648KR vs AD648KRZ AD648KR vs AD642 AD648KR price AD648KR stock Analog Devices AD648KR AD648KR SOIC footprint AD648KR precision instrumentation AD648KR 1 MHz 10 pA

相关元器件 & 术语

Analog Devices AD648 AD648KR AD648KRZ AD648S AD642 LF442 TL062 dual operational amplifier precision BiFET op amp J-FET input stage analog amplifier semiconductor input bias current quiescent current input offset voltage offset voltage drift unity-gain bandwidth slew rate common-mode rejection CMOS DAC buffer electrochemical sensor photodiode signal chain 8-pin SOIC SOIC package family surface-mount package RoHS REACH
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情