Analog Devices

ADM207EANZ - 230 kbps RS-232 Transceiver | Analog Devices

MPN: ADM207EANZ ✓ Aktif
+5 V Vdss 24-pin PDIP Package
MOQ: 1 |

ADM207EANZ Genel Bakış

The Analog Devices ADM207EANZ is a single-chip RS-232 interface transceiver with five transmitters, three receivers, and operation from a single +5 V supply. It supports data rates up to 230 kbps, conforms to the EIA-232E and CCITT V.28 specifications, and is packaged in a 24-pin PDIP. The ADM207E family is designed for robust communications interfaces where modern ±12 V supplies are unavailable.

An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 line levels and converts received RS-232 signals back into CMOS-compatible logic. Within the product hierarchy, it belongs to interface ICs, communication transceivers, and RS-232 line-interface devices. This combination of drivers, receivers, and single-supply operation simplifies equipment requiring bidirectional serial connectivity over longer distances than a logic-level UART alone can support.

The ADM207EANZ provides five driver channels for transmitting data and three receiver channels for receiving data. Its maximum specified data rate of 230 kbps accommodates industrial serial links, point-of-sale equipment, test systems, and legacy peripheral interfaces. Operation from one +5 V supply reduces external power requirements, while CMOS implementation supports integration with digital control logic. The ADM207E product family also provides Shutdown and Enable controls on selected models.

The 24-pin PDIP package supports through-hole PCB assembly and is useful where field replacement, socketed construction, or repairability is important. The five-transmitter, three-receiver arrangement differs from many RS-232 transceivers that provide only one driver and one receiver, allowing several ports to share one interface package. Conversely, designs requiring four receivers should check whether the ADM208EANZ configuration better matches the channel count.

Typical uses include industrial control consoles, laboratory instrumentation, data acquisition equipment, serial adapters, and embedded systems communicating with legacy RS-232 peripherals. Because EIA-232E and CCITT V.28 behavior define the electrical interface, board-level implementation still requires careful treatment of ground references, cable routing, protection, and logic-level compatibility with the connected UART.

The most important design check is channel allocation. Five drivers and three receivers must be mapped against the required DTE or DCE signals before placement. Keep the transceiver and connector grounds together where required, route exposed interface leads away from sensitive logic, and use suitable protection components when cables leave the enclosure or connect to industrial equipment.

This page combines the manufacturer's family specifications with package details, sourced pricing, channel-level comparisons, and practical RS-232 design guidance. It also distinguishes true same-package alternatives from configuration changes that may require different signal assignments, helping engineers evaluate replacement choices before modifying an existing board.

Drop-in alternatifler için ADM207EANZ — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller ADM207EANZ (aynı form faktörü ve ayağa oturma) — farklı olan Maximum Data Rate, Package, Supply Voltage.

Analog Devices
Maximum Data Rate: 230 kbps
Package: 24-pin PDIP
İle Karşılaştır ADM207EANZ →
Analog Devices
Maximum Data Rate: 200 kbps
Package: 24-pin PDIP, 0.300 inch (7.62 mm) pitch
Supply Voltage: 4.5 V to 5.5 V
İle Karşılaştır ADM207EANZ →

ADM207EAN

✅ Yerleştirme
Analog Devices
📦 24-pin PDIP
5 · 3 · 230 kbps · RS-232 · ±15 kV · 8 kV

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

ADM208EANZ

✅ Yerleştirme
📦 24-pin PDIP
Uses the same 24-pin PDIP but changes from five transmitters and three receivers to four transmitters and four receivers, a 20% reduction in transmitters and a 33% increase in receivers.

📋 Katalogda Olmayan Referans Alternatifi

ADM207EANZ Özellikler

Product Type RS-232 interface transceiver
Transmitter Channels 5 channels
Receiver Channels 3 channels
Besleme Gerilimi +5 V
Maximum Data Rate 230 kbps
RS-232 Standard EIA-232E
CCITT Standard CCITT V.28
Technology CMOS
Paket 24-pin PDIP
Montaj Türü Through-hole
Pin Sayısı 24 pins

ADM207EANZ 24-pin pdip Pin Yapısı Kılavuzu

ADM207EANZ (24-pin pdip paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.

24-pin pdip paket pin çizelgesi için ADM207EANZ

Ayrıntılı pin çıkış verisi mevcut değil: ADM207EANZ.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

ADM207EANZ için uygundur 6 uygulamas: Industrial Control Consoles, Point-of-Sale Terminals, Laboratory Test Equipment, Data Acquisition Systems, Legacy Serial Adapters, Embedded Serial Communications.

🏭

Industrial Control Consoles

The ADM207EANZ fits industrial consoles that must connect several RS-232 peripherals through one interface package. Its five transmitters and three receivers provide more line-level channels than a basic one-driver, one-receiver transceiver, while single +5 V operation simplifies the power architecture. The 230 kbps maximum rate supports many legacy controller and data-acquisition protocols. Engineers should map each DTE or DCE signal before layout, then separate exposed cable routing from sensitive digital traces. The major trade-off is channel imbalance: applications needing a fourth receiver should evaluate ADM208EANZ instead.

🖥️

Point-of-Sale Terminals

The ADM207EANZ can support point-of-sale equipment that connects a printer, scanner, display interface, or other legacy peripheral through RS-232. Its five driver channels allow several outbound commands and status signals to share an interface IC, while three receivers can accept inbound device data. The 230 kbps capability is more than adequate for many peripheral protocols, subject to UART baud-rate and cable-length limits. Single +5 V operation also helps systems that lack legacy ±12 V rails. Pin assignment, logic levels, and connector polarity must match the selected DTE or DCE role.

🔧

Laboratory Test Equipment

The ADM207EANZ is suitable for laboratory instruments that must communicate with older RS-232 analyzers, programmable supplies, or test fixtures. Multiple transmitter channels can drive separate control signals, and the three receiver channels can collect responses without requiring three separate interface packages. Its maximum 230 kbps rate supports instrument-control protocols operating within that limit. The CMOS implementation operates from +5 V and integrates well with digital control circuitry, although the receive logic thresholds must be compatible with the host. Use the family pin table for exact functions and protect external cables as required by the installation environment.

📡

Data Acquisition Systems

The ADM207EANZ can bridge a multi-channel data-acquisition controller to RS-232 instruments or legacy sensors. Three receiver channels support incoming measurement results or acknowledgments, while five transmitter channels can provide commands, enables, and routing signals. Operation from a single +5 V rail simplifies system partitioning around modern processors and FPGAs, and the 230 kbps maximum data rate suits many moderate-speed acquisition links. The interface still requires careful signal mapping, grounding, and isolation decisions. If the acquisition architecture requires four inbound channels, the ADM208EANZ's 4/4 configuration may be a better functional fit.

🔌

Legacy Serial Adapters

The ADM207EANZ is appropriate for legacy serial adapters that add several RS-232 lines to a modern embedded controller. The five transmitters and three receivers can support multiple command and status paths while keeping the host side on a single +5 V supply. Its 230 kbps ceiling accommodates many legacy UART protocols without requiring a high-speed differential interface. The PDIP package remains practical for repairable or socketed industrial electronics. A critical design check is the relationship between host UART direction and the available driver and receiver counts; unused RS-232 lines should be handled according to the manufacturer's recommended circuit configuration.

🧩

Embedded Serial Communications

The ADM207EANZ can provide a multi-channel RS-232 boundary for embedded systems connected to older service equipment or external controllers. Its single +5 V operation aligns with modern digital rails, while CMOS implementation supports compact communication logic. Five drivers and three receivers allow more flexible command, enable, and status routing than a conventional one-channel RS-232 interface. The 24-pin PDIP package is especially useful where through-hole maintenance is preferred. Designers must still validate UART logic levels, connector signaling, cable length, and ground references; when only one RS-232 direction is needed, a smaller transceiver may reduce board area.

Önerilen Ürünler Özeti

What is the ADM207EANZ?
The ADM207EANZ is a single-chip, single-supply RS-232 interface transceiver manufactured by Analog Devices. It contains five transmitters and three receivers, operates from +5 V, supports data rates up to 230 kbps, and is offered in a 24-pin PDIP package. According to the Analog Devices ADM207E product page, the family conforms to the EIA-232E and CCITT V.28 interface specifications.
How many RS-232 drivers and receivers does ADM207EANZ have?
The ADM207EANZ has five RS-232 transmitter channels and three receiver channels. This channel arrangement supports systems that need to drive more than one RS-232 line while receiving three signals from connected equipment. DigiKey identifies the exact ADM207EANZ device as a full 5/3 RS-232 transceiver, and the manufacturer describes the ADM207E family as a CMOS interface family operating from a single +5 V supply.
What is the maximum data rate of ADM207EANZ?
The ADM207EANZ supports RS-232 operation at up to 230 kbps. According to the Analog Devices ADM207E product page, devices in this family fully conform to the EIA-232E and CCITT V.28 specifications and operate at data rates up to 230 kbps. This rate is suitable for industrial control links, legacy peripherals, test equipment, and serial adapters when UART timing and cable limitations are handled correctly.
What supply voltage does ADM207EANZ require?
The ADM207EANZ operates from a single +5 V supply. This allows RS-232 line-level conversion without separate +12 V and -12 V rails. The ADM207E family is implemented in CMOS technology and is intended for communication interfaces where ±12 V is unavailable. Logic interfacing still requires confirmation that the UART supply levels match the receiver and driver-control input thresholds.
What package is used by ADM207EANZ?
The ADM207EANZ is packaged in a 24-pin PDIP. The through-hole package is identified in distributor listings as PDIP-24 and is appropriate for conventional through-hole assembly, sockets, repairable equipment, and industrial controller boards. Because the RS-232 transceiver is available in multiple package technologies within the ADM207E family, verify the complete ordering code before substituting a surface-mount variant.
Where can I download the ADM207EANZ datasheet PDF?
The official ADM207EANZ documentation is available from the Analog Devices ADM207E product page at https://www.analog.com/en/products/adm207e.html. The manufacturer page provides the family datasheet and ordering information, including the ADM207EANZ 24-pin PDIP configuration. Use the pin-description table and absolute-maximum-rating section in the manufacturer datasheet when assigning PCB functions and validating power and signal conditions.
Where is the ADM207EANZ pinout located?
The ADM207EANZ pinout is shown in the pin-configuration table of the Analog Devices ADM207E manufacturer datasheet. The exact device uses a 24-pin PDIP, but pin names and signal assignments must be taken from that table rather than inferred from another package in the family. The pin-description table should be used when assigning transmitter outputs, receiver inputs, supply, ground, and any control functions.
Where can I buy ADM207EANZ online?
Use the Request a Quote form on this page to request ADM207EANZ pricing, stock confirmation, and order handling for the exact 24-pin PDIP ordering code. The form allows buyers to identify the required quantity and confirm current supply without relying on a stale listing. Request the manufacturer datasheet with the quotation so the line assignment, package, and environmental requirements can be verified before release.
What is the price of ADM207EANZ?
Use the Request a Quote form on this page for the current ADM207EANZ unit price and volume quotation. The form is preferable to a static price because component pricing, availability, and allocation can change while an order is being prepared. Submit the exact MPN, ADM207EANZ, together with the required quantity, packaging preference, and target delivery location for a current quotation.
What is the lead time for ADM207EANZ?
Request the current lead time through the Request a Quote form on this page. Lead time depends on manufacturer inventory, order quantity, component allocation, and the delivery location, so it should be confirmed for the current order rather than treated as a fixed device characteristic. Include the desired delivery date in the request to allow the supplier to identify available production and expedited options.
Is ADM207EANZ in stock?
Stock for ADM207EANZ should be confirmed through the Request a Quote form on this page using the exact 24-pin PDIP MPN. An active distributor listing does not by itself guarantee the quantity available for a new order. State the required order quantity, target date, and shipment destination in the request so the seller can confirm allocation and the expected fulfillment schedule.
ADM207EANZ vs ADM208EANZ: which is better?
Choose the ADM207EANZ when the design needs five RS-232 drivers and three receivers, and choose the ADM208EANZ when four drivers and four receivers better match the port allocation. Both devices use the same 24-pin PDIP package, but their channel counts differ by one driver and one receiver. The correct choice is the one whose available transmitter and receiver channels can be assigned without leaving a required RS-232 signal unsupported.
What is the difference between ADM207EANZ and ADM207EAN?
The ADM207EAN and ADM207EANZ are both listed as 24-pin PDIP ADM207E devices, with the ADM207EANZ carrying the Z ordering suffix. Their primary distinction is the exact ordering-code and temperature-grade treatment rather than a change in the fundamental five-transmitter, three-receiver RS-232 architecture. For a new replacement, compare the complete manufacturer ordering table, temperature range, and RoHS package information before approving either part.
When should I choose ADM207EANZ over ADM208EANZ?
Choose ADM207EANZ when the board needs to transmit on five RS-232 lines and receive on three, particularly for DTE or DCE arrangements where the extra transmit capability is more valuable than the fourth receive channel. Choose ADM208EANZ when the interface is receive-heavy or uses four independent inbound lines. Because both parts occupy a 24-pin PDIP, the channel configuration and board-level signal assignment should determine the choice.
What is the best drop-in replacement for ADM207EANZ?
The closest same-package replacement is the ADM207EAN, while the ADM208EANZ is a configuration alternative in the same 24-pin PDIP family. No cross-brand drop-in replacement is established here, so verify the complete pin and signal map before substitution. The ADM208EANZ changes the transmitter-to-receiver ratio from five-to-three to four-to-four, meaning software, cabling, and board assignments must be checked rather than assuming every function is interchangeable.
Can ADM207EANZ replace ADM208EANZ?
The ADM207EANZ can be considered for an ADM208EANZ position only when the required interface can operate with five transmitters and three receivers instead of four transmitters and four receivers. Both are 24-pin PDIP devices, but the different channel counts can change which RS-232 lines are supported. Confirm the pin-by-pin signal map, UART direction, cable configuration, and any unused-line handling before treating the change as a drop-in replacement.

Mühendislik referans verileri: ADM207EANZ — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose ADM207EANZ when the system needs a single +5 V RS-232 interface with five transmit channels and three receive channels, particularly for industrial, test, or legacy communications equipment. Its 24-pin PDIP and 230 kbps capability make it suitable for repairable through-hole designs. Choose ADM207EAN when the exact suffix and environmental-grade treatment better match an approved BOM. Choose ADM208EANZ when four drivers and four receivers provide a better match for receive-heavy interfaces, but verify its signal map rather than assuming automatic equivalence. A smaller device such as MAX3221EIDBR may be preferable when only one RS-232 direction is required and board area matters. No cross-brand drop-in alternative was established, so any proposed substitute requires package, pin-function, logic-level, channel-count, and lifecycle verification before PCB release.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün ADM207EAN ADM208EANZ
Package 24-pin PDIP 24-pin PDIP 24-pin PDIP
Brand Analog Devices Analog Devices Analog Devices
Transmitter Channels 5 channels 5 channels 4 channels
Receiver Channels 3 channels 3 channels 4 channels
Mounting Type Through-hole Through-hole Through-hole
Ordering Suffix Z Non-Z ordering code Z

Ana Farklılayıcılar

  • Higher transmit-channel count than the ADM208EANZ (karşılaştırma:ADM208EANZ)
  • Retains the five-transmitter, three-receiver architecture in an alternate ordering code (karşılaştırma:ADM207EAN)
  • Single-supply operation avoids external ±12 V rails (karşılaştırma:ADM208EANZ)
  • Multi-channel RS-232 integration reduces interface IC count (karşılaştırma:MAX3221EIDBR)

Tasarım Notları

Assign every RS-232 line before routing the PCB. The ADM207EANZ provides five transmitter outputs and three receiver inputs, so a design requiring four inbound signals may require the ADM208EANZ or another transceiver. Confirm DTE versus DCE signal roles, UART direction, logic polarity, and connector pin numbering against the manufacturer pin-description table. Treat unused outputs and inputs according to the family's recommended termination rather than leaving them unexamined.

Keep the IC, supply decoupling, and connector interface routing compact, but keep external RS-232 conductors away from sensitive clocks, sensor inputs, and high-speed digital traces. Connect the transceiver and connector ground according to the system grounding strategy, especially when the cable introduces an earth potential difference. Route driver outputs directly toward their connector pins without long shared segments or sharp stubs. This separation reduces capacitive coupling and common-mode disturbance while preserving signal integrity.

Do not assume that the ADM207EANZ and ADM208EANZ are interchangeable solely because both use a 24-pin PDIP. Their transmitter-to-receiver ratios are 5/3 and 4/4 respectively, so one configuration may remove a required transmit path while adding a receive path. Validate the complete signal map, software expectations, cable wiring, and termination arrangement. Also confirm the UART logic levels and supply conditions before power-up because the RS-232 line interface does not eliminate all logic-level compatibility constraints.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The available ADM207E information references the EU EMC directive for the family, but no explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 declaration for ADM207EANZ is stated here. AEC-Q100 is not applicable to this general-purpose interface device.

Veri doğrulanma tarihi: 2026-11-19 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

ADM207EANZ datasheet ADM207EANZ pinout ADM207EANZ datasheet pdf ADM207EANZ 24 pin PDIP ADM207EANZ RS-232 transceiver ADM207EANZ 230 kbps ADM207EANZ replacement ADM207EANZ equivalent ADM207EANZ vs ADM208EANZ Analog Devices ADM207EANZ ADM207EANZ price ADM207EANZ stock ADM207EANZ RS-232 application circuit ADM207EANZ lead time

İlgili Bileşenler ve Terimler

Analog Devices ADM207EANZ ADM207EAN ADM208EANZ MAX3221EIDBR RS-232 EIA-232E CCITT V.28 RS-232 transceiver interface IC communication transceiver CMOS 5/3 transceiver 230 kbps single +5 V supply 24-pin PDIP DIP package through-hole mounting surface mount UART DTE DCE industrial control data acquisition RoHS
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle