ADM3490ARZ - 10Mbps RS-485/422 Transceiver | Analog Devices
MPN: ADM3490ARZ ✓ AktifADM3490ARZ Genel Bakış
A differential line transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable transmission over noisy interconnects. The ADM3490ARZ belongs to the RS-485/RS-422 transceiver hierarchy, combining a line driver, a differential receiver, and an interface supply in one device. Balanced signaling improves noise immunity by rejecting common-mode voltage, while the receiver reconstructs the intended logic state from the difference between two signal conductors.
The principal features include operation from a single 3.3 V supply, a maximum data rate of 10 Mbps, reduced slew rates for low EMI, half- and full-duplex family options, and interoperability with 5 V logic. Its receiver input impedance is 12 kΩ, allowing up to 32 transceivers on a bus. A shutdown function supports low-power operation, while thermal-shutdown protection helps prevent excessive internal heating from sustained fault conditions.
The ADM3490ARZ is designed around a differential driver and differential receiver suitable for point-to-point, multipoint, and multidrop RS-485 networks. The reduced edge rate spreads high-frequency energy more broadly and reduces ringing and radiated emissions compared with an unrestricted 10 Mbps edge rate. Logic-compatible receiver output and driver input interfaces simplify connection to 3.3 V controllers while permitting interoperability with systems containing 5 V logic.
Typical applications include industrial automation, factory equipment, building controls, instrumentation links, and embedded RS-485 networks. It is particularly useful when a design needs more speed than the 250 kbps ADM3483 and ADM3488 class while retaining reduced-slew-rate behavior for electromagnetic compatibility. The SOIC-8 footprint also supports conventional surface-mount assembly and copper-based thermal dissipation.
For robust bus implementation, place the transceiver close to the connector and route the differential pair as a tightly coupled trace over a continuous reference plane.Termination, biasing, and protection components should be placed where they can be changed or inspected without disturbing the signal pair. The manufacturer datasheet should be used to confirm the exact pin assignments, input thresholds, timing limits, and bus loading conditions for the selected system.
This page combines the manufacturer's device characteristics with practical interface guidance, a parameter-focused comparison against same-footprint alternatives, and design notes for PCB routing, termination, and fault protection. These engineering details help distinguish a genuinely drop-in replacement from a transceiver that is only functionally similar but incompatible with the existing ADM3490ARZ footprint.
Drop-in alternatifler için ADM3490ARZ — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller ADM3490ARZ (aynı form faktörü ve ayağa oturma) — farklı olan Package, Product Type, Maximum Data Rate, Logic Compatibility, Receiver Input Impedance.
ADM3485ARZ
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
ADM3486ARZ
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
ADM3488ARZ
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
ADM3491ARZ
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →ADM3490EARZ
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
MAX3490ECSA+
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →ADM3490ARZ Özellikler
| Product Type | Differential RS-485/RS-422 line transceiver |
| Besleme Gerilimi | 3.3 V |
| Maximum Data Rate | 10 Mbps |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Logic Compatibility | Interoperable with 5 V logic |
| Standards Compatibility | EIA RS-422 and RS-485 compliant |
| Receiver Input Impedance | 12 kΩ |
| Maximum Bus Loading | 32 transceivers |
| Slew Rate | Reduced |
| Duplex Support | Half-duplex and full-duplex family options |
| Shutdown Support | Yes |
| Thermal Protection | Thermal shutdown |
| Paket | 8-SOIC, 3.90 mm width |
| Montaj Türü | Surface mount |
| İşletim Sıcaklığı Aralığı | -40°C to +85°C |
ADM3490ARZ Pin Yapısı
| Pin 1 | RO — Receiver output |
| Pin 2 | /RE — Active-low receiver enable |
| Pin 3 | DE — Driver enable |
| Pin 4 | DI — Driver input |
| Pin 5 | GND — Ground |
| Pin 6 | A — Non-inverting differential bus terminal |
| Pin 7 | B — Inverting differential bus terminal |
| Pin 8 | VCC — 3.3 V supply |
Tipik Uygulamalar
ADM3490ARZ için uygundur 6 uygulamas: Industrial Automation Bus, Factory Sensor Network, Building Control Network, Instrumentation Data Link, Embedded Controller Communication, Robust Field-Bus Gateway.
Industrial Automation Bus
The ADM3490ARZ fits industrial automation links that require deterministic differential signaling at speeds up to 10 Mbps. Place it at the bus node between the controller and an RS-485 connector, with separate differential nets for the driver and receiver as required by the selected topology. Its reduced-slew-rate operation limits high-frequency edge energy and radiated emissions, which is valuable around motors, contactors, and switching supplies. The 12 kΩ receiver input impedance also permits up to 32 transceivers on a bus, although cable length, node spacing, termination, and protection requirements still determine the usable communication distance.
Önerilen
Factory Sensor Network
The ADM3490ARZ can connect a controller to remote sensors over a noise-resistant balanced RS-485 bus. Its 10 Mbps maximum rate supports high-refresh sensor traffic, while the reduced slew rate reduces the fast-edge content that can couple into adjacent machinery and sensitive analog circuits. The transceiver should be located close to the line connector, with the A and B conductors routed as a matched pair and common-mode transients handled by appropriately selected protection devices. A 3.3 V supply also permits direct interfacing with modern embedded controllers, subject to the input and output logic levels defined in the manufacturer datasheet.
Önerilen
Building Control Network
The ADM3490ARZ is suitable for controller nodes in building-management networks where reliable communication must coexist with lighting, switching, and relay noise. The differential receiver rejects common-mode disturbance that would corrupt a single-ended link, and the reduced-slew-rate driver lowers EMI compared with a faster-edge implementation. In a panel design, terminate only the physical ends of the bus, avoid unnecessary cable stubs, and place surge protection near the external connector. The 3.3 V operating supply supports low-power nodes, and the shutdown function can reduce consumption when a controller periodically powers down its bus interface.
Önerilen
Instrumentation Data Link
The ADM3490ARZ can carry commands and measurement data between an instrumentation controller and remote test equipment over a balanced RS-422 or RS-485 connection. A 10 Mbps ceiling allows the link to service higher-rate digital payloads while the controlled transition rate improves compatibility with longer cables and sensitive test environments. Keep the bus driver near the connector to minimize stub lengths, and observe the receiver's common-mode range and enabled-state behavior. The low-power 3.3 V architecture is useful in compact instrumentation, although the system designer must confirm cable-length timing margins and grounding strategy.
Önerilen
Embedded Controller Communication
The ADM3490ARZ provides a compact interface between an embedded controller and a 3.3 V RS-485 peripheral bus. The driver and receiver permit bidirectional half-duplex communication when the circuit uses the appropriate enable controls, while 5 V logic interoperability expands compatibility with mixed-voltage equipment. Because the part supports up to 32 bus nodes, it can consolidate several remote modules without exceeding the stated receiver loading. Firmware must control driver enable so that multiple transmitters do not contend on the bus, and the PCB should preserve symmetry between the A and B routes to minimize differential-mode noise pickup.
Önerilen
Robust Field-Bus Gateway
The ADM3490ARZ can serve as the physical-layer element in a field-bus gateway that translates between an embedded processor and an external RS-485 network. Its 10 Mbps capability supports burst data transfer, and the reduced slew rate helps limit emissions in compact equipment where connector filtering and board area are constrained. Place the transceiver near the edge connector, use a continuous ground reference under the pair, and include protection selected for the cable's surge and ESD environment. The shutdown feature may be used during low-activity periods, but the system must ensure that bus contention and receiver enable timing remain compatible with the network protocol.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: ADM3490ARZ — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | ADM3485ARZ | ADM3486ARZ | ADM3488ARZ | ADM3491ARZ | ADM3490EARZ | MAX3490ECSA |
|---|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Maxim Integrated |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Interface Standards | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 |
| Number of Drivers | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| Number of Receivers | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
Ana Farklılayıcılar
- Provides substantially higher link rate than the 250 kbps ADM3488 option (karşılaştırma:ADM3488ARZ)
- Maintains the same 3.3 V and 8-SOIC implementation as the ADM3490E alternative (karşılaştırma:ADM3490EARZ)
- Uses the same core RS-485/RS-422 function and reduced-slew-rate approach as ADM3485 (karşılaştırma:ADM3485ARZ)
- Combines a compact SOIC footprint with cross-brand sourcing options (karşılaştırma:MAX3490ECSA)
Tasarım Notları
Route the ADM3490ARZ A and B conductors as a closely coupled differential pair over a continuous ground plane. Keep the transceiver near the connector, avoid stubs on unused bus nodes, and maintain symmetrical spacing to minimize differential-mode emissions and susceptibility. Place termination and protection components near the cable interface, but keep switching nodes and digital edges away from the bus pair. Use the manufacturer pin configuration and recommended-layout guidance when assigning the SOIC-8 footprint.
Do not enable the driver and receiver simultaneously unless the protocol and bus topology require that state. Firmware must release the bus before another node transmits, preventing driver contention and excess current. Check the active-low receiver-enable function and the DE driver-enable polarity against the firmware and pull-up or pull-down arrangement. Also confirm that the selected alternative's enable behavior matches the ADM3490ARZ rather than relying on the common package name alone.
The reduced slew rate is intended to lower EMI, but PCB and cable layout still determine radiated and conducted noise. Keep the bus path short from transceiver to connector, use a solid reference plane, avoid split-plane crossings, and provide a low-impedance ground return. External cables should include appropriately rated surge and ESD protection. Verify that added protection capacitance does not distort the intended 10 Mbps signal and that the bus remains within the receiver's common-mode limits.
Place the local 3.3 V bypass capacitor close to the VCC and ground pins, with the return connected directly to the device ground. The bypass network should suppress supply noise without creating long current loops in the differential pair. Check the complete supply range and current draw against the Analog Devices manufacturer datasheet, especially when the shutdown function is active or the transceiver operates at the stated maximum bus-loading limit.
Uyumluluk Bilgisi
The ADM3490 is an industrial interface IC rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation in the manufacturer's current product documentation or declaration files.