ADS774KU - 12-Bit 125 kSPS SAR ADC | Texas Instruments
MPN: ADS774KU ✗ Son Kullanım ZamanıADS774KU Genel Bakış
An ADC is an interface IC that converts an analog voltage into a digital code for processing, measurement, or control. The successive-approximation, or SAR, architecture compares the sampled input against an internal CDAC and internal reference through a sequence of conversion steps. The ADS774 family follows the hierarchy of data-converter IC, analog-to-digital converter, and microprocessor-compatible sampling ADC, reducing the need for external sample-and-hold and supporting direct connection to parallel microprocessor buses.
The primary electrical features include 12-bit resolution, one single-ended analog input, a maximum sampling rate of 125 kSPS, and a maximum conversion time of 8.5 microseconds over temperature. The converter can operate from a single +5 V supply and supports analog input ranges extending to ±16.5 V in the cited family information. Its internal reference, clock, sampling network, and byte-wide parallel interface make it suitable for compact data-acquisition and industrial-control systems.
Internally, the ADS774 uses a low-power CMOS capacitor-array DAC and successive-approximation conversion sequence. Internal sampling captures the input before conversion, while the reference and oscillator support a self-contained measurement channel. The byte-wide parallel outputs suit microprocessors and control logic that read the converted code directly. Designers should still verify acquisition timing, bus timing, input settling, and reference requirements against the manufacturer datasheet for the exact operating conditions.
Typical uses include industrial process monitoring, sensor signal acquisition, laboratory measurement equipment, embedded control systems, and legacy microprocessor-based data acquisition. The 28-pin SOIC package also supports board-level migration to documented pin-compatible ADS774 family variants when temperature grade, accuracy, or lifecycle requirements differ.
Layout and signal-integrity practices are as important as nominal converter performance. Keep analog input traces short, place input and reference bypass components close to their associated pins, and route digital outputs away from sensitive analog nodes. Confirm acquisition time against the source-impedance and sampling-capacitor requirements before selecting the input buffer or external network.
This page organizes the ADS774KU specifications, lifecycle information, package details, drop-in family alternatives, comparison data, and application guidance into one engineering reference. Use the manufacturer datasheet for the definitive pin description, timing diagrams, electrical limits, and ordering information.
Drop-in alternatifler için ADS774KU — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
ADS774JU/1K
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
ADS774HIBDW
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
ADS774HIDW
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
ADS774KU Maksimum Değerlendirmeler & Elektriksel Özellikler
| Çözünürlük | 12 bit |
| Maximum Sampling Rate | 125 kSPS |
| Maximum Conversion Time | 8.5 us over temperature |
| Architecture | Successive approximation (SAR) |
| Converter Type | Sampling CMOS ADC |
| Number of Analog Inputs | 1 |
| Input Type | Single-ended |
| Internal Conversion Mechanism | 12-bit capacitor-array DAC (CDAC) |
| Reference | Internal |
| Clock | Internal |
| Output Interface | Byte-wide parallel |
| Sampling Circuit | Internal |
| Besleme Gerilimi | +5 V |
| Analog Supply Range | ±16.5 V |
| İşletim Sıcaklığı Aralığı | -40 C to +85 C |
| Paket | 28-pin SOIC (DW) |
| Montaj Türü | Surface mount |
| RoHS Durumu | Compliant |
ADS774KU 28-pin soic (dw) Pin Yapısı Kılavuzu
ADS774KU (28-pin soic (dw) paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: ADS774KU.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
ADS774KU için uygundur 6 uygulamas: Industrial Sensor Acquisition, Process Control Monitoring, Laboratory Data Acquisition, Embedded Control Systems, Sensor Signal Conditioning, Legacy Interface Replacement.
Industrial Sensor Acquisition
The ADS774KU fits industrial sensor-acquisition channels that require a compact, self-contained 12-bit SAR ADC. Its internal sampling circuit, reference, clock, and byte-wide parallel interface reduce the number of external analog and timing components, while the 125 kSPS maximum rate supports acquisition of moderately fast process variables. Place the converter close to the sensor or conditioning network, and select an input buffer and acquisition components that settle the ADC input within the manufacturer-defined acquisition window.
Önerilen
Process Control Monitoring
ADS774KU is appropriate for pressure, temperature, level, and other slow-to-medium-speed process measurements where 12-bit resolution is useful and parallel data can be captured by embedded control logic. The 125 kSPS maximum conversion rate permits rapid sequential channel updates, and the internal reference and clock simplify deterministic measurement channels. Design the analog input network for the required source impedance and avoid routing high-current digital return paths beneath the analog input or reference connections.
Önerilen
Laboratory Data Acquisition
The ADS774KU supports laboratory and instrumentation designs requiring repeated analog measurements with a processor-readable digital result. Its 12-bit SAR converter, 125 kSPS maximum sampling rate, internal sampling network, and 8.5 microsecond maximum conversion time provide a useful combination of speed and integration. For instrumentation-grade results, account for input noise, reference performance, grounding, calibration, and the acquisition interval needed by the source rather than treating the maximum conversion rate as the complete system throughput.
Önerilen
Embedded Control Systems
ADS774KU can serve as the acquisition front end in a legacy or parallel-bus embedded controller because it provides a byte-wide parallel output alongside an internal reference, clock, and sampling network. The interface supports direct microprocessor reads, while the 28-pin SOIC package is practical for established through-hole-to-surface-mount board redesigns. Firmware must account for the required conversion-start, acquisition, busy, and read timing defined by the manufacturer datasheet.
Önerilen
Sensor Signal Conditioning
The ADS774KU is suitable for digitizing conditioned outputs from resistive, bridge, and low-level voltage sensors when a 12-bit result is sufficient. Internal sampling removes the need for a separate sample-and-hold stage in most applications, while the single +5 V supply and parallel output simplify mixed analog-digital implementation. Select the amplifier, protection network, and input-series resistance together so the source settles accurately before each conversion and transient protection does not degrade the required signal bandwidth.
Önerilen
Legacy Interface Replacement
ADS774KU supports design continuity for boards originally built around the ADC574, ADC674, or ADC774 families because the manufacturer identifies it as a drop-in replacement in most applications. The integrated sampling network, internal reference and clock, CMOS implementation, and single +5 V operation can simplify replacement of older complete data-converter assemblies. Before substituting it into an existing design, verify pin-level functions, input polarity, acquisition timing, bus timing, supply sequencing, and any legacy external sample-and-hold components.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: ADS774KU — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | ADS774JU/1K | ADS774HIBDW | ADS774HIDW |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-pin SOIC (DW) | 28-pin SOIC - same | 28-pin SOIC - same | 28-pin SOIC - same |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit |
| Architecture | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) |
| Number of Channels | 1 | 1 | 1 | 1 |
| Input Type | Single-ended | Single-ended | Single-ended | Single-ended |
| Maximum Sampling Rate | 125 kSPS | 117 kSPS | 117 kSPS | 117 kSPS |
| Output Interface | Byte-wide parallel | Byte-wide parallel | Parallel | Parallel |
Ana Farklılayıcılar
- Higher maximum conversion rate within the same ADS774 family (karşılaştırma:ADS774JU/1K)
- Faster maximum sampling rate than the documented HI-grade successor (karşılaştırma:ADS774HIBDW)
- Faster maximum sampling rate with the same package and interface class (karşılaştırma:ADS774HIDW)
Tasarım Notları
Treat the analog input path as a settling network rather than a direct connection. Select the source impedance, series resistance, and acquisition duration so the external network charges the ADC sampling capacitor to the required accuracy within the acquisition window defined by the manufacturer datasheet. Keep the analog trace short, minimize parasitic capacitance, and place any input-series or filter components close to the converter.
Separate analog input and reference routing from the byte-wide digital output bus. Use a continuous ground reference beneath the analog section where the package and board design permit, keep bypass connections short, and route converter-control signals away from sensitive input nodes. Check the package pin assignment and recommended layout directly in the manufacturer datasheet before finalizing tracks and component placement.
Do not base system throughput solely on the 125 kSPS headline rate. The usable rate also depends on acquisition time, conversion completion, bus-read timing, and processor service time. When replacing older ADC574-, ADC674-, or ADC774-based assemblies, verify input polarity, pin functions, control timing, output coding, supply requirements, and any external sample-and-hold components.
Uyumluluk Bilgisi
The product comparison identifies ADS774KU as RoHS compliant. Other environmental and material-compliance fields are not established by the available catalog information.