BCM8728BIFBG - Dual 10GbE SFI-to-XAUI PHY | Broadcom
MPN: BCM8728BIFBG ✗ Son Kullanım ZamanıBCM8728BIFBG Genel Bakış
A physical-layer transceiver is the semiconductor block that converts a high-speed serial data stream into a parallel digital interface and handles the electrical signaling required at the device boundary. Within the broader hierarchy, this component is a transceiver IC, then a network interface IC, then an integrated circuit used in networking and telecommunications equipment. The BCM8728BIFBG also supports LAN and WAN equipment architectures where low-latency Ethernet links are required.
The principal documented characteristics are its dual-channel architecture, 10GbE operation, SFI input interface, and XAUI output interface. Electronic decision-making capability, identified in the device description, supports signal-handling functions within the physical layer. These features distinguish the BCM8728BIFBG as a dedicated high-speed Ethernet interface rather than a general-purpose serial transceiver or a complete Ethernet controller.
The SFI-to-XAUI conversion architecture places the BCM8728BIFBG between optical or copper-facing SFI sources and an XAUI interface on a network processor, Ethernet switch, or router. Operating two channels in one device can simplify multiport designs where parallel 10GbE links are required. The XAUI interface provides a parallel high-speed connection to digital switching logic, while SFI provides the serial-facing connection used by 10GbE physical-layer implementations.
Typical use cases include 10GbE switches, routers, line cards, aggregation equipment, WAN appliances, and network interface cards. It is particularly relevant where two 10GbE channels must be exposed to an XAUI-capable host processor. Design selection also requires confirming the host XAUI electrical interface, board-level channel requirements, thermal conditions, and the reference design associated with the exact Broadcom device variant.
The primary engineering consideration is that SFI and XAUI are not interchangeable interfaces. PCB routing must preserve the signal integrity required by each side of the device, including controlled-impedance XAUI traces and appropriately terminated SFI connections. Designers should follow the Broadcom reference design and layout guidance for the exact package and board revision rather than infer dimensions or pin assignments from the ordering code.
This product record combines the available manufacturer and distributor technical identification with practical interface, layout, and sourcing guidance. It highlights where the BCM8728BIFBG fits in a 10GbE design, distinguishes its documented SFI-to-XAUI function from complete Ethernet controllers, and provides a structured basis for comparing future drop-in options when verified package-level and pin-level cross-reference data becomes available.
Drop-in alternatifler için BCM8728BIFBG — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu ürüne yer değiştirme seçenekleri mevcut değil.
Alternatifleri Talep EdinBCM8728BIFBG Maksimum Değerlendirmeler & Elektriksel Özellikler
| Product Type | Dual-channel 10GbE SFI-to-XAUI LAN/WAN physical-layer transceiver |
| Channel Count | 2 channels |
| Veri Hızı | 10 Gb/s per channel |
| Serial Input Interface | SFI |
| Parallel Output Interface | XAUI |
| Network Role | LAN/WAN physical-layer transceiver |
| Signal-Decision Feature | EDC electronic decision-making capability |
| Semiconductor Category | Integrated circuit |
| Interface Category | Telecom interface IC |
BCM8728BIFBG standard Pin Yapısı Kılavuzu
BCM8728BIFBG (standard paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: BCM8728BIFBG.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
BCM8728BIFBG için uygundur 6 uygulamas: 10GbE Enterprise Switches, 10GbE Router Interfaces, WAN Edge Appliances, Network Line Cards, Traffic Aggregation Platforms, Network Interface Cards.
10GbE Enterprise Switches
The BCM8728BIFBG fits enterprise switching platforms that need two 10GbE SFI-facing links connected to an XAUI-capable switching ASIC. Its dual-channel architecture can reduce the number of physical-layer transceiver devices needed on a multiport line card. The design must preserve SFI and XAUI signal integrity, provide the required reference and supplies, and follow the Broadcom reference layout. Review the exact electrical limits and thermal data before production release because the available component record does not establish package-level operating limits.
10GbE Router Interfaces
The BCM8728BIFBG is appropriate for router and aggregation interfaces where two serial 10GbE links must interface to an XAUI network processor. It separates the physical-layer signaling function from packet processing performed by the host processor. This division allows the router architecture to reuse a high-speed parallel host interface while facing external links through SFI. Validate clocking, reference-design topology, board channel loss, and implementation timing against the manufacturer documentation before integrating the device.
WAN Edge Appliances
The BCM8728BIFBG can support LAN/WAN edge appliances requiring a dedicated dual-channel 10GbE physical-layer interface. Its SFI-to-XAUI conversion supports designs that terminate high-speed serial links into an XAUI-capable ASIC rather than implementing the physical layer in the host device. This is useful for edge aggregation, branch routing, and traffic-inspection systems. Deployment still depends on exact operating-temperature, supply-voltage, lifecycle, and compliance requirements being confirmed for the target enclosure and industry.
Network Line Cards
A multiport 10GbE line card can use the BCM8728BIFBG where each card needs paired 10GbE physical-layer channels linked to an XAUI switching or packet-processing ASIC. The integrated dual-channel arrangement helps maintain a consistent high-speed interface architecture across the card. Designers should budget connector reach, optical or copper module requirements, channel skew, and thermal paths when planning the board. Exact pin assignments and package land patterns must come from the Broadcom package drawing rather than be inferred from the MPN.
Traffic Aggregation Platforms
Traffic aggregation platforms benefit from the BCM8728BIFBG when the backplane or uplink architecture uses two 10GbE serial links and an XAUI host connection. The device provides the physical-layer bridge between those interface domains, allowing the aggregation ASIC to handle packet processing. Board implementation should preserve controlled-impedance XAUI routing and provide clean SFI connections to the appropriate module or backplane transceiver. Compliance and environmental requirements should be assessed separately for the complete system.
Network Interface Cards
The BCM8728BIFBG is suitable for a dedicated dual-port 10GbE network interface card built around an XAUI-capable controller. Each channel provides a serial 10GbE SFI-side connection while the controller handles higher-level communication and traffic processing. This arrangement can simplify high-throughput server, storage, and test systems requiring deterministic Ethernet links. Confirm host-controller timing, power sequencing, thermal performance, connector configuration, and the manufacturer's board guidance before fabricating production hardware.
Mühendislik referans verileri: BCM8728BIFBG — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün |
|---|---|
| Brand | Broadcom |
| Channel Count | 2 channels |
| Data Rate | 10 Gb/s per channel |
| Serial Interface | SFI |
| Parallel Interface | XAUI |
| Network Role | LAN/WAN physical-layer transceiver |
| EDC Capability | Electronic decision-making capability |
Tasarım Notları
Treat the SFI and XAUI interfaces as separate high-speed design domains. Route XAUI as controlled-impedance, length-matched traces on the stack-up specified by the Broadcom reference design, and follow its launch and termination requirements. Place SFI connection and decoupling structures close to the relevant pins. Confirm the exact package and pin names in the manufacturer pin-description table before assigning any board net.
Use the package land pattern, pin-one orientation, exposed-pad geometry, and solder-mask requirements from the datasheet drawing. Do not derive the footprint from the BIFBG ordering suffix. Review via-in-pad or thermal-via recommendations, solder-mask clearance, and copper keepouts against the package drawing, especially if the package contains a thermal pad that must connect to a ground plane.
Separate supply rails and sensitive signal connections according to the reference schematic, and place required bypass capacitors at the package-side power pins. Estimate total rail dissipation only after the exact voltage and current conditions are established from the datasheet. Use the calculated dissipation and the package thermal model to determine whether additional copper, airflow, or thermal relief is necessary.
Do not treat the BCM8728BIFBG as a full 10GbE MAC, switch, or packet processor; it is a dual SFI-to-XAUI physical-layer transceiver. Avoid selecting a replacement solely because it also supports 10GbE. A true drop-in decision requires identical package geometry, pin-to-pin assignments, supply rails, timing behavior, reference-clock requirements, EDC configuration, and thermal constraints.
Uyumluluk Bilgisi
Compliance attributes are not stated in the Broadcom product identification and should be confirmed from the exact manufacturer documentation or declarations before procurement.