CD40193BD - 4-Bit Dual-Clock Counter | Texas Instruments
MPN: CD40193BD ✓ AktifCD40193BD Genel Bakış
A binary up/down counter is a sequential logic device that increments or decrements a 4-bit binary value according to the active clock input. The CD40193BD adds preset and reset controls, allowing the counter state to be loaded or cleared independently of its counting inputs. This places it within the CMOS logic IC hierarchy: counter > sequential logic > digital logic > integrated circuit. Unlike a mechanical counter, it provides electronic state storage, programmable count direction, and direct interface logic levels.
The principal functional characteristics are 4-bit counting capacity, dual-clock up/down operation, positive-edge triggering, a 16-pin through-hole CDIP package, and a 500 ns propagation delay. These parameters make the part useful where a compact bidirectional event counter must respond deterministically to separate increment and decrement commands. Preset capability also supports repeatable sequence generation, decade-oriented control functions, and position tracking without additional external state registers.
The counter operates from a single power rail and uses CMOS logic inputs. Its synchronous operation means that the counter state changes on the active clock edge, helping avoid asynchronous data races in sequential control systems. The 500 ns propagation-delay figure is the principal timing constraint when determining the maximum clock rate or the required settling interval before sampling the four output bits.
Typical applications include industrial counters, stepper-motor position accumulators, frequency-divider and sequencing logic, test and measurement systems, and legacy control equipment. It can also implement pulse-domain position tracking when increment pulses represent forward motion and decrement pulses represent reverse motion. In such systems, the preset input initializes a known reference position, while the reset input establishes a clear starting condition.
Designers should route each clock only to the intended count-direction input and account for the 500 ns propagation delay when sampling outputs. Decoupling close to the power pins helps control supply noise, while unused inputs must be tied to a defined logic level. Because the part is packaged as a 16-pin CDIP rather than a surface-mount device, board layout must preserve through-hole footprint clearance and adequate spacing for insertion and soldering.
This product overview combines the manufacturer description, distributor device attributes, package details, timing information, and cross-reference findings into an engineering-focused guide. It also identifies design constraints and package-specific information that help engineers assess CD40193BD suitability before integrating it into a new PCB or replacing an existing counter.
Drop-in alternatifler için CD40193BD — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
CD40193BD/3
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
CD40193BD Maksimum Değerlendirmeler & Elektriksel Özellikler
| Counter Type | Binary up/down counter |
| Counting Element | 1 element |
| Counter Width | 4 bits |
| Logic Family | CMOS |
| Counting Direction | Up or down |
| Clock Inputs | 2 independent clocks |
| Edge Trigger | Positive edge |
| Operating Mode | Synchronous |
| Preset Function | Presettable |
| Reset Function | Resettable |
| Propagation Delay | 500 ns |
| Number of Terminals | 16 terminals |
| Paket | 16-CDIP |
| Package Form | Rectangular DIP |
| Montaj Türü | Through-hole |
| Temperature Grade | Military |
| Seated Height | 5.08 mm |
CD40193BD rectangular dip Pin Yapısı Kılavuzu
CD40193BD (rectangular dip paket) için pin yapısı. Bu dijital IC, GPIO, iletişim arayüzleri (UART, SPI, I2C) ve güç pinleri içerir. Alternatif pin işlevleri ve yapılandırma seçenekleri için üretici veri kitapçığını referans alın. Tünel sistem tasarımı ve PCB yerleşimi için temel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: CD40193BD.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
CD40193BD için uygundur 6 uygulamas: Industrial Pulse Counter, Stepper-Motor Position Accumulator, Digital Frequency Divider, Test and Measurement Sequence Control, Legacy Equipment Repair, Repeatable Timing Sequence.
Industrial Pulse Counter
The CD40193BD is appropriate for an industrial event-counting module that receives forward events on one clock and reverse events on the other. Its 4-bit synchronous counter state records 16 count positions, while the separate positive-edge inputs prevent direction ambiguity. A 500 ns propagation delay allows a moderately paced event stream to be sampled after the clock edge. The 16-CDIP through-hole format also suits repairable control equipment with larger through-hole spacing. The preset function can establish a reference position, and reset can clear the count after a completed cycle. Before finalizing the board, verify the supply limits, logic thresholds, and operating-temperature limits against the manufacturer datasheet.
Önerilen
Stepper-Motor Position Accumulator
A stepper-motor axis can use the CD40193BD to accumulate commanded position by routing forward-step pulses to the up-count clock and reverse-step pulses to the down-count clock. The 4-bit output provides a modulo-16 position state, and preset allows the axis to be re-zeroed at a known coordinate. Because counting is synchronous and positive-edge triggered, the direction input can change without introducing a ripple-style count sequence. The stated 500 ns propagation delay defines the interval before the counter outputs should be considered settled. This application is best suited to low-speed positioning where the 4-bit range and listed timing are adequate.
Önerilen
Digital Frequency Divider
The CD40193BD can divide a periodic input into a lower-rate count sequence by applying the source signal to one of its clock inputs. The four counter outputs then represent successive binary states, allowing downstream logic to derive divided timing or discrete sequencing intervals. Positive-edge triggering gives a defined sampling point, and the 500 ns propagation delay provides the minimum interval before the outputs are used. The part is most appropriate for moderate-frequency control signals where a 4-bit counter is sufficient. Engineers should derive the actual maximum input frequency from the required settling margin and confirm the electrical operating limits before fixing the clock source.
Önerilen
Test and Measurement Sequence Control
In a test instrument, the CD40193BD can track successive fixture steps or measurement events in a compact 4-bit sequence. The preset control initializes the sequence at a defined state, while reset supports restarting a measurement pass. Separate count clocks allow motion or acquisition-complete events to advance the sequence in opposite directions. Its listed 500 ns propagation delay helps the controller determine when output bits are stable for sampling. The 16-CDIP package is useful in laboratory instruments designed for through-hole construction and serviceability. The design must still account for the limited 4-bit range and verify supply, noise, and temperature constraints from the manufacturer documentation.
Önerilen
Legacy Equipment Repair
The CD40193BD is useful for maintaining older industrial and laboratory equipment that used a through-hole 16-pin bidirectional counter. Its military temperature grade and 5.08 mm seated height are explicitly identified for the device, helping engineers match the mechanical characteristics of the original board. The 4-bit synchronous counting function can replace a failed counter without redesigning the surrounding logic. Board restoration should still verify pin orientation, supply voltage, reset polarity, and clock behavior against the equipment schematic. The package is suitable for conventional through-hole soldering and axial or radial insertion where sufficient board clearance is available.
Önerilen
Repeatable Timing Sequence
The CD40193BD can generate a repeatable sequence of up to 16 timing states when driven from a periodic clock. Preset establishes the first state, while the binary outputs advance on each positive edge and provide decoded timing-enable signals. The 500 ns propagation delay should be included in the setup and hold requirements of any logic driven by the outputs. This approach is practical for legacy sequencing controllers and automated test fixtures that need simple modulo-16 behavior without a microcontroller. Validate clock rise and fall times, supply-noise tolerance, and output loading against the manufacturer specifications before using the counter with long external traces.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: CD40193BD — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | CD40193BD/3 |
|---|---|---|
| Brand | Texas Instruments | RCA |
| Package | 16-CDIP | 16-CDIP |
| Counter Type | Binary up/down counter | Binary up/down counter |
| Counter Width | 4 bits | 4 bits |
| Counting Element | 1 element | 1 element |
| Clock Configuration | Dual clock | Dual clock |
| Triggering | Positive edge | Positive edge |
Ana Farklılayıcılar
- Independent positive-edge count directions (karşılaştırma:CD40193BD/3)
- Documented 500 ns propagation delay (karşılaştırma:CD40193BD/3)
- Explicit military-grade designation (karşılaştırma:CD40193BD/3)
- Mechanical height documented for legacy-board restoration (karşılaştırma:CD40193BD/3)
Tasarım Notları
Use the 500 ns propagation delay as the minimum settling reference after an active positive clock edge. Sample the four counter outputs only after this interval, and ensure any external logic connected to those outputs satisfies the input setup and hold requirements. Keep clock traces short and away from noisy switching nodes because the counter responds to edges rather than voltage levels.
Do not allow both count-direction clocks to switch without deliberate system timing. Routing unrelated signals to the unused clock can create unintended increments or decrements. When the unused clock is disabled, connect it to a defined inactive logic level, and verify reset and preset polarity directly from the manufacturer terminal-description table before making PCB assignments.
Plan the board around the 16-CDIP footprint rather than a generic 16-pin DIP position without checking the exact body and lead geometry. Maintain adequate clearance around the counter for through-hole insertion and soldering, including the stated 5.08 mm seated height. Place the bypass capacitor close to the power and ground pins and route clock and counter-output traces away from switching-power nodes.
Uyumluluk Bilgisi
The available product and distributor records do not state exact-MPN RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. The military temperature grade must not be interpreted as AEC-Q100 automotive qualification.