Texas Instruments

DS90LV001TLD-NS - 800 Mbps LVDS Buffer | Texas Instruments

MPN: DS90LV001TLD-NS ✗ Son Kullanım Zamanı
3.3 V single supply Vdss 8-WSON, 3 x 3 mm Package
MOQ: 1 |

DS90LV001TLD-NS Genel Bakış

The Texas Instruments DS90LV001TLD-NS is a single-channel 800 Mbps LVDS-to-LVDS buffer with a typical propagation delay of 1.4 ns and typical peak-to-peak jitter of 100 ps, housed in an 8-WSON surface-mount package measuring 3 x 3 mm. It operates from a single 3.3 V supply and provides a fully differential signal path for backplane and point-to-point LVDS links.

An LVDS buffer is a high-speed interface IC that regenerates a low-voltage differential signaling signal while preserving the logic state and differential signaling characteristics required by the receiver. In the electronics hierarchy, the DS90LV001 belongs to the LVDS interface-buffer class, interface IC category, and broader signal-integrity and data-communication semiconductor family. Its primary role is to isolate and restore signals traveling through controlled-impedance board traces, especially when long traces, connectors, or backplane stubs create loading and reflections.

The device provides an 800 Mbps data rate, 1.4 ns typical propagation delay, and 100 ps typical peak-to-peak jitter when tested with a 2^23 - 1 pseudo-random binary sequence. It is compatible with the ANSI/TIA/EIA-644-A LVDS standard. The manufacturer also specifies an industrial temperature range of -40 °C to +85 °C and offers both 8-pin SOIC and space-saving 8-WSON options, with the WSON body saving approximately 70% of board area relative to the SOIC option.

The fully differential input-to-output architecture helps maintain common-mode control and rejects noise that is common to both conductors. Because the DS90LV001 is designed for 800 Mbps operation, PCB layout remains a critical part of the design. Differential impedance, component placement, return paths, connector geometry, and transmission-line termination must be evaluated together to preserve signal integrity at the intended data rate.

Typical applications include LVDS clock distribution, backplane signal conditioning, point-to-point links between industrial controllers, high-speed instrumentation, test and measurement equipment, and communication systems that distribute differential signals over controlled-impedance interconnect. The buffer is particularly useful when the source and destination are not close enough for a clean direct connection or when a transmission-line segment needs regeneration before another receiver stage.

Use the manufacturer's pin-description table and recommended-layout guidance when assigning PCB tracks. Keep the differential pair continuous with matched geometry, place termination components close to the receiving device, and route over a continuous reference plane. Avoid adding unterminated stubs because they can create reflections that degrade the 800 Mbps edge rate.

This page combines the manufacturer specifications, replacement information, package details, and application-oriented design guidance in one engineering reference. It also distinguishes the exact orderable MPN from other DS90LV001 ordering codes so procurement, footprint review, and signal-integrity validation can be completed against the correct device.

Drop-in alternatifler için DS90LV001TLD-NS — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

DS90LV001TLD/NOPB

✅ Yerleştirme
📦 8-WSON (3 x 3 mm)
Same 800 Mbps LVDS function, 3.3 V supply, and 8-WSON footprint; ordering suffix changes from -NS to /NOPB

📋 Katalogda Olmayan Referans Alternatifi

DS90LV001TLD-NS Özellikler

Fonksiyon Single-channel LVDS-to-LVDS buffer
Maximum Data Rate 800 Mbps
Propagation Delay 1.4 ns typical
Peak-to-Peak Jitter 100 ps typical with PRBS = 2^23 - 1 at 800 Mbps
Besleme Gerilimi 3.3 V single supply
Signal Path Fully differential
LVDS Standard ANSI/TIA/EIA-644-A
Channel Count 1 channel
İşletim Sıcaklığı Aralığı -40 °C to +85 °C
Paket 8-WSON, 3 x 3 mm
Montaj Türü Surface mount
Space Saving Versus SOIC Approximately 70% smaller
Alternative Package 8-pin SOIC

DS90LV001TLD-NS 8-pin soic Pin Yapısı Kılavuzu

DS90LV001TLD-NS (8-pin soic paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.

8-pin soic paket pin çizelgesi için DS90LV001TLD-NS

Ayrıntılı pin çıkış verisi mevcut değil: DS90LV001TLD-NS.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

DS90LV001TLD-NS için uygundur 6 uygulamas: LVDS Backplane Signal Conditioning, High-Speed LVDS Clock Distribution, Industrial Controller Point-to-Point Links, Test and Measurement Equipment, High-Speed Instrumentation Interconnect, Communication Equipment Signal Distribution.

🌐

LVDS Backplane Signal Conditioning

The DS90LV001TLD-NS is suitable for regenerating an 800 Mbps LVDS signal across a backplane segment where trace loading, connector transitions, or receiver stubs could otherwise degrade edge quality. Its fully differential path preserves the encoded logic state while presenting a new LVDS output to the next controlled-impedance segment. The 1.4 ns typical propagation delay and 100 ps typical peak-to-peak jitter provide useful timing margins for properly terminated links. Place the buffer close to the source or split point, maintain continuous differential geometry over a reference plane, and avoid unterminated branches because those discontinuities create reflections that can become significant at an 800 Mbps edge rate.

🖥️

High-Speed LVDS Clock Distribution

The DS90LV001TLD-NS can distribute a differential clock at rates up to 800 Mbps when the source must drive a remote receiver through a board or cable transition. Regenerating the clock provides a cleaner output than relying on the original source across a long or loaded trace. Its typical 1.4 ns propagation delay must be included in clock-budget analysis, while the 100 ps typical peak-to-peak jitter helps characterize timing margin. Keep the clock pair closely coupled, provide the required LVDS termination at the receiver, and use matched connectors and reference planes so the clock sees a controlled-impedance path.

🏭

Industrial Controller Point-to-Point Links

The DS90LV001TLD-NS supports industrial point-to-point communication where a controller and peripheral must exchange an 800 Mbps LVDS signal across a routed board region. Its -40 °C to +85 °C industrial temperature range covers factory equipment, instrumentation, and industrial automation environments. The buffer isolates the transmitting stage from downstream loading and produces a restored differential output for the receiving device. Use it only when the connected devices implement compatible LVDS electrical signaling, and observe the manufacturer's recommended termination arrangement at both ends of the transmission line.

🔧

Test and Measurement Equipment

The DS90LV001TLD-NS fits high-speed test and measurement systems that distribute differential stimulus, trigger, or measurement-clock signals. At 800 Mbps, the buffer can regenerate a signal before it enters a longer instrument interconnect, reducing sensitivity to source loading. The 1.4 ns typical propagation delay should be calibrated out of time-domain measurements, and the 100 ps typical jitter figure provides a reference for edge-quality assessment. Controlled-impedance routing, nearby termination, and careful grounding are essential because laboratory cables and connectors can introduce additional reflections not represented by the IC specifications.

📺

High-Speed Instrumentation Interconnect

The DS90LV001TLD-NS can isolate an instrumentation signal path when a front-end ASIC, converter, or data-capture device drives a remote circuit through a long board trace. The 800 Mbps operation preserves high data-rate capability, while the fully differential topology helps reject common-mode noise and maintain a defined differential output. Use it as a regeneration point rather than as a protocol translator: input encoding, output encoding, clocking, and termination must remain compatible with the rest of the link. Decoupling and return-path continuity should follow the manufacturer layout guidance to prevent supply or reference-plane discontinuities from appearing on the data path.

🌐

Communication Equipment Signal Distribution

The DS90LV001TLD-NS is applicable in communication equipment that sends one LVDS signal between subsystems separated by a connector or extended controlled-impedance trace. Its 800 Mbps data-rate capability and typical 1.4 ns delay suit many internal serial links, and its surface-mount 8-WSON 3 x 3 mm package supports compact boards. The package saves approximately 70% of the area associated with the 8-pin SOIC option according to the manufacturer. The trade-off is tighter layout sensitivity: the compact body requires short capacitor connections, uninterrupted ground reference, and differential routing that maintains consistent spacing throughout the escape and routing regions.

Önerilen Ürünler Özeti

DS90LV804 LVDS interface family for multi-channel distribution Kullanıldığı Yer: LVDS Backplane Signal Conditioning, High-Speed LVDS Clock Distribution, Test and Measurement Equipment, Communication Equipment Signal Distribution DS90LV001TLD/NOPB Same-family drop-in sourcing option Kullanıldığı Yer: LVDS Backplane Signal Conditioning, High-Speed LVDS Clock Distribution, Industrial Controller Point-to-Point Links, Test and Measurement Equipment, High-Speed Instrumentation Interconnect, Communication Equipment Signal Distribution DS10BR150 Related high-speed differential interface device Kullanıldığı Yer: Industrial Controller Point-to-Point Links, High-Speed Instrumentation Interconnect
What is the DS90LV001TLD-NS?
The DS90LV001TLD-NS is a single-channel 800 Mbps LVDS-to-LVDS buffer from Texas Instruments. According to the manufacturer product page, it provides a fully differential signal path, a typical propagation delay of 1.4 ns, and typical peak-to-peak jitter of 100 ps with a 2^23 - 1 PRBS pattern at 800 Mbps. It is packaged for surface mounting in an 8-WSON 3 x 3 mm body.
What is the maximum data rate of DS90LV001TLD-NS?
The DS90LV001TLD-NS supports data rates up to 800 Mbps. The Texas Instruments product page identifies it as an 800 Mbps LVDS buffer and specifies its jitter as 100 ps peak-to-peak typical when a 2^23 - 1 pseudo-random binary sequence is applied at 800 Mbps. This operating point makes the device suitable for high-speed differential clock and data distribution.
Where can I download the DS90LV001TLD-NS datasheet PDF?
The official DS90LV001 datasheet is linked from the Texas Instruments DS90LV001 product page at https://www.ti.com/product/DS90LV001. Use the manufacturer link for the authoritative electrical characteristics, pin descriptions, recommended operating conditions, and layout guidance. The historical DS90LV001TLD data-sheet listings are also indexed online, but the current TI product page is the preferred starting point for exact DS90LV001TLD-NS documentation.
Where is the pinout for DS90LV001TLD-NS?
The DS90LV001TLD-NS pinout is identified by the manufacturer’s DS90LV001 documentation and its 8-WSON package drawing. The device uses an 8-WSON 3 x 3 mm package, and individual signal names should be taken from the pin-description table in the official datasheet. Before laying out a PCB, confirm the exposed-pad or thermal-pad connection and every supply and ground assignment against that table.
What supply voltage does DS90LV001TLD-NS require?
The DS90LV001TLD-NS operates from a single 3.3 V supply. The Texas Instruments product page explicitly identifies the device as a single +3.3 V supply LVDS buffer. Its bypass and decoupling network should follow the manufacturer layout recommendations, with short supply connections and a continuous ground reference maintained beneath the high-speed signal path.
Is DS90LV001TLD-NS compatible with ANSI/TIA/EIA-644-A LVDS?
Yes, the DS90LV001TLD-NS is compatible with the ANSI/TIA/EIA-644-A LVDS standard. The Texas Instruments product page lists this compliance alongside its 800 Mbps operation and fully differential data path. Compliance supports interface interoperability, although the final system still requires controlled-impedance routing, suitable termination, and careful connector implementation.
What can replace DS90LV001TLD-NS?
The verified direct replacement is DS90LV001TLD/NOPB from Texas Instruments. The manufacturer product page identifies DS90LV001TLD/NOPB as the current no-lead ordering code for the same DS90LV001 800 Mbps LVDS-buffer function in the 8-WSON 3 x 3 mm package. Confirm the exact pin assignments and ordering information in the datasheet before exchanging the devices in production hardware.
Can DS90LV001TLD/NOPB replace DS90LV001TLD-NS?
Yes, DS90LV001TLD/NOPB is the practical same-footprint replacement for DS90LV001TLD-NS. Both identify the Texas Instruments DS90LV001 800 Mbps LVDS buffer in the 8-WSON 3 x 3 mm package, so the functional, speed, and package requirements align. The suffix identifies orderable commercial conditions, while the manufacturer datasheet remains the controlling document for pin-level and ordering details.
When should I choose DS90LV001TLD-NS over another LVDS buffer?
Choose DS90LV001TLD-NS when a system needs one LVDS signal to be regenerated for a 800 Mbps differential link and an 8-WSON 3 x 3 mm footprint is required. Its 1.4 ns typical propagation delay and 100 ps typical peak-to-peak jitter suit high-speed point-to-point or backplane distribution. A multi-channel or internally terminated device should be preferred when those functions are specifically required.
Is DS90LV001TLD-NS suitable for backplane and clock distribution?
Yes, the DS90LV001TLD-NS is suitable for backplane signal conditioning and LVDS clock distribution. The manufacturer describes the buffer as regenerating an LVDS input into an LVDS output for systems where long traces and unterminated receiver stubs can limit speed. Its 800 Mbps capability and 1.4 ns typical delay provide useful margin for properly terminated controlled-impedance links.
What is the best Texas Instruments equivalent for DS90LV001TLD-NS?
The best Texas Instruments equivalent is DS90LV001TLD/NOPB. It is the manufacturer’s no-lead ordering code for the DS90LV001 800 Mbps LVDS buffer in the same 8-WSON 3 x 3 mm package. The matched 800 Mbps data rate and fully differential architecture make it more suitable as a direct substitute than a different-family LVDS device with a different channel count or pin assignment.
Is there a verified cross-brand drop-in replacement for DS90LV001TLD-NS?
No cross-brand drop-in replacement is established for DS90LV001TLD-NS. The available device is a dedicated single-channel 800 Mbps LVDS buffer in an 8-WSON 3 x 3 mm package, and the manufacturer-specific ordering code DS90LV001TLD/NOPB provides the closest verified match. Use the Request a Quote form on this page if an approved alternate-source qualification is required.
How does DS90LV001TLD-NS help LVDS signal integrity?
The DS90LV001TLD-NS regenerates an LVDS input and provides a new LVDS output through a fully differential data path. This helps isolate a source from downstream loading and allows a controlled-impedance segment to feed another receiver. The 1.4 ns typical propagation delay and 100 ps typical jitter define its high-speed timing behavior, while proper termination and layout remain essential.
Where can I request a quote for DS90LV001TLD-NS?
Use the Request a Quote form on this page to request DS90LV001TLD-NS pricing, current availability, lead time, and minimum order quantity. The historical distributor listing identifies the exact MPN as an in-stock item, but inventory and commercial terms can change. Submit the requested quantity and target package or shipment details with the quote request.
What are the key specifications engineers should know about DS90LV001TLD-NS?
The principal DS90LV001TLD-NS specifications are an 800 Mbps maximum data rate, 1.4 ns typical propagation delay, 100 ps typical peak-to-peak jitter, a single 3.3 V supply, a fully differential path, and an industrial temperature range of -40 °C to +85 °C. It is an 8-WSON 3 x 3 mm surface-mount device compatible with ANSI/TIA/EIA-644-A LVDS operation.

Mühendislik referans verileri: DS90LV001TLD-NS — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose DS90LV001TLD-NS when the BOM specifies that exact MPN and the installed design requires a single-channel 800 Mbps LVDS buffer in an 8-WSON 3 x 3 mm footprint. For new production procurement, DS90LV001TLD/NOPB is the verified same-family ordering option because it retains the stated 800 Mbps rate, 3.3 V supply, fully differential path, and package. The device is appropriate for controlled-impedance point-to-point, backplane, and clock-distribution paths where the source-to-destination timing budget includes approximately 1.4 ns typical propagation delay. Do not select a multi-channel DS90LV804-family device as a drop-in replacement because its channel count and pin arrangement differ. A cross-brand alternative should not be assumed: dedicated single-channel 800 Mbps LVDS buffers with the same footprint and pinout were not established. Validate termination, differential impedance, connector behavior, exposed-pad treatment, and the manufacturer’s latest ordering information before releasing a replacement into production.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün DS90LV001TLD/NOPB
Package 8-WSON (3 x 3 mm) 8-WSON (3 x 3 mm)
Brand Texas Instruments Texas Instruments
Function Single-channel LVDS-to-LVDS buffer Single-channel LVDS-to-LVDS buffer
Maximum Data Rate 800 Mbps 800 Mbps
Propagation Delay 1.4 ns typical 1.4 ns typical
Peak-to-Peak Jitter 100 ps typical with PRBS = 2^23 - 1 at 800 Mbps 100 ps typical with PRBS = 2^23 - 1 at 800 Mbps
Supply Voltage 3.3 V single supply 3.3 V single supply
Signal Path Fully differential Fully differential
LVDS Standard ANSI/TIA/EIA-644-A compatible ANSI/TIA/EIA-644-A compatible
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C

Ana Farklılayıcılar

  • Exact same-family sourcing path for an obsolete-ordering-code transition (karşılaştırma:DS90LV001TLD/NOPB)
  • High-speed timing with a compact footprint (karşılaştırma:DS90LV001TLD/NOPB)
  • Direct compatibility with standard LVDS interconnects (karşılaştırma:DS90LV001TLD/NOPB)

Tasarım Notları

Route the LVDS input and output as a tightly coupled differential pair over a continuous reference plane. Maintain uniform spacing and avoid plane changes, vias, and split-plane transitions wherever possible. Because the device supports 800 Mbps, even a small impedance discontinuity can create a reflected edge. Keep the pair away from noisy switching paths and preserve a continuous return-current path beneath both conductors.

Do not add unterminated stubs to an LVDS trace. The DS90LV001 is intended to regenerate signals for controlled-impedance transmission lines, not to compensate for arbitrary branch geometry. Follow the manufacturer termination recommendations at the receiver and ensure that connector or test-point branches are properly terminated. Otherwise, reflected signals can overlap the next bit and degrade jitter or produce data errors.

Use the manufacturer’s recommended decoupling arrangement and place the input, output, and supply connections as short as practical. The compact 8-WSON body saves approximately 70% of the board area of the SOIC option, but that same compactness requires disciplined escape routing. Check the package drawing for the exposed-pad connection and ensure its thermal and electrical treatment matches the official land pattern.

Budget the 1.4 ns typical propagation delay when assessing source-to-destination timing, especially in clocked or round-trip systems. The 100 ps typical peak-to-peak jitter specification was measured with a 2^23 - 1 PRBS pattern at 800 Mbps; actual board jitter can be higher because of reflections, loss, connector transitions, and power-supply noise. Validate the complete channel with representative termination and enclosure conditions.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The manufacturer material explicitly identifies ANSI/TIA/EIA-644-A LVDS compatibility and an industrial temperature range. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established for the exact -NS orderable MPN.

İlgili Aramalar

ds90lv001tld nopb DS90LV001TLD-NS datasheet DS90LV001TLD-NS pinout DS90LV001TLD-NS datasheet pdf DS90LV001TLD-NS replacement DS90LV001TLD-NS equivalent DS90LV001TLD-NS 800 Mbps DS90LV001TLD-NS 8-WSON DS90LV001TLD/NOPB price DS90LV001TLD/NOPB stock Texas Instruments DS90LV001TLD-NS DS90LV001TLD-NS LVDS buffer DS90LV001TLD-NS propagation delay DS90LV001TLD-NS cross reference

İlgili Bileşenler ve Terimler

Texas Instruments DS90LV001TLD-NS DS90LV001TLD/NOPB DS90LV804 DS10BR150 LVDS buffer LVDS-to-LVDS buffer interface IC semiconductor signal buffer signal repeater fully differential signal path 800 Mbps 1.4 ns propagation delay 100 ps peak-to-peak jitter 3.3 V power supply ANSI/TIA/EIA-644-A 8-WSON package WSON family surface-mount package controlled-impedance routing backplane signal distribution LVDS clock distribution industrial temperature range
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle