Renesas Electronics

ICS571MT - 160MHz 1:2 Zero Delay Buffer | Renesas Electronics

MPN: ICS571MT ✓ Aktif
8-pin SOIC, 3.90 mm width Package 160 MHz Speed
MOQ: 1 |

ICS571MT Genel Bakış

Renesas Electronics ICS571MT is a high-speed, low-phase-noise zero delay buffer (ZDB) designed to distribute one CMOS clock input to two true CMOS outputs. It operates up to 160 MHz, supports a 1:2 input-to-output ratio, and is packaged in an 8-pin SOIC measuring approximately 3.90 mm wide. The part integrates analog and digital phase adjustment to minimize clock skew and preserve low-noise timing performance.

A zero delay buffer is a clock-management IC that uses a phase-adjustable buffer architecture to compensate for propagation delay introduced by clock distribution networks. Within the broader hierarchy, it is a fanout buffer, then a clock buffer, then a clock and timing IC, and finally a semiconductor. By placing a ZDB close to a clock-consuming circuit, designers can reduce the timing penalty associated with board traces, while a 1:2 ratio allows one source clock to feed two independent loads.

Key characteristics include a maximum frequency of 160 MHz, CMOS inputs, CMOS outputs, PLL capability, one input circuit, two true outputs, and an input-to-output ratio of 1:2. The ICS571MT can also operate as a low-phase-noise frequency multiplier according to the manufacturer description. Its low-skew outputs are useful when related clocks must remain closely aligned, and phase noise better than -100 dBc/Hz is described from 10 kHz to 1 MHz offset from the carrier under the cited operating conditions.

The typical application is clock fanout in telecommunications, networking, industrial control, test and measurement, and digital processing systems. It can distribute a common clock to two domains, provide clock buffering between a source and a load, or provide two low-skew copies of a reference signal. The 8-pin SOIC package supports conventional surface-mount assembly and is easier to handle than a fine-pitch BGA package.

Designers should maintain short, impedance-controlled clock traces, use a ground reference close to the device, and verify source and load termination against the clock edge rate. A nominal maximum frequency does not guarantee acceptable timing margin in every board environment; rise time, loading, return paths, and available setup and hold time must be evaluated together.

This page combines the manufacturer-described operating characteristics, packaging information, application guidance, and verified drop-in candidates to support faster component evaluation and board-level sourcing decisions.

Drop-in alternatifler için ICS571MT — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

ICS570MT

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
📦 8-pin SOIC
Same 570-series 8-pin SOIC footprint; family-specific frequency, ratio, and skew ratings require verification

📋 Katalogda Olmayan Referans Alternatifi

ICS574MLF

✅ Yerleştirme
📦 8-pin SOIC
Two true CMOS outputs and lead-free PDSO-8 package; PLL-based architecture differs from the ICS571MT zero-delay function

📋 Katalogda Olmayan Referans Alternatifi

ICS574MLFT

✅ Yerleştirme
📦 8-pin SOIC
Two true CMOS outputs and lead-free PDSO-8 package; PLL-based architecture differs and timing limits require verification

📋 Katalogda Olmayan Referans Alternatifi

ICS571ML

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
📦 8-pin SOIC
Same 571-series and 8-pin SOIC footprint; frequency, ratio, and output configuration require pin-level verification

📋 Katalogda Olmayan Referans Alternatifi

ICS572MT

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
📦 8-pin SOIC
Same 570-series package family; clock ratio, maximum frequency, and propagation-delay characteristics require verification

📋 Katalogda Olmayan Referans Alternatifi

ICS571MT Özellikler

Device Type Fanout buffer (distribution), zero delay buffer IC
Maximum Frequency 160 MHz
Number of Circuits 1
Input-to-Output Ratio 1:2
Input Logic Type CMOS
Output Logic Type CMOS
Number of True Outputs 2
PLL Yes
Architecture Analog/digital phase-adjustable zero delay buffer
Input Clock Frequency at 3.3 V Up to 160 MHz
Phase Noise Better than -100 dBc/Hz from 10 kHz to 1 MHz offset from carrier
Paket 8-pin SOIC, 3.90 mm width
Montaj Türü Surface mount
Lead-Free Status Lead free
Output Drive High output drive

ICS571MT 8-pin soic, 3.90 mm width Pin Yapısı Kılavuzu

ICS571MT (8-pin soic, 3.90 mm width paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.

8-pin soic, 3.90 mm width paket pin çizelgesi için ICS571MT

Ayrıntılı pin çıkış verisi mevcut değil: ICS571MT.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

ICS571MT için uygundur 6 uygulamas: Telecommunications Clock Fanout, Networking and Ethernet Clock Distribution, Industrial Control Clock Trees, Test and Measurement Instrumentation, High-Speed Digital Processor Clocking, Synchronous Data Acquisition.

🌐

Telecommunications Clock Fanout

The ICS571MT is appropriate for distributing a common clock to two telecommunications or data-processing domains while maintaining low phase noise and low output skew. Its 160 MHz maximum input frequency at 3.3 V provides useful margin for demanding digital logic, while the two true CMOS outputs avoid inversion-related phase surprises. Place the buffer near the clock split or receiver branches, provide a continuous ground reference, and terminate each output according to its actual edge rate and load. The principal trade-off is that a zero delay buffer is not a programmable PLL, so a design requiring synthesized frequencies or independent ratios should use a PLL clock driver instead.

🌐

Networking and Ethernet Clock Distribution

The ICS571MT can fan out a 160 MHz-class source clock into two true CMOS branches used by network controllers, physical-layer devices, or fabric clocking logic. Low-skew outputs help retain alignment between related destinations, and the 1:2 ratio fits designs where two loads share one source. The design should minimize trace mismatch and provide a low-impedance reference plane because skew from unequal routing can consume the available setup margin. Confirm the receiver thresholds, clock edge rate, and supply voltage before release, especially where the source already provides a strong buffer.

🏭

Industrial Control Clock Trees

For industrial control systems, the ICS571MT provides two non-inverted CMOS clock outputs from one input, reducing the loading burden on an upstream oscillator or controller. Its high output drive is useful when driving local logic through a short PCB network, while the low-phase-noise architecture supports deterministic timing in acquisition and control paths. Keep the device away from high-current switching nodes, provide local supply bypassing, and account for temperature and loading changes during worst-case timing analysis. If the system must generate unrelated frequencies for multiple domains, a PLL-based clock driver offers more flexibility than this fixed-ratio buffer.

🖥️

Test and Measurement Instrumentation

The ICS571MT is useful in test and measurement equipment where one precision reference must reach two acquisition, conversion, or processing paths with closely related timing. The 160 MHz upper frequency supports high-speed digital backplanes, and the two true outputs can preserve clock polarity across both destinations. For laboratory-grade performance, characterize phase noise, edge rate, output jitter, and temperature drift on the final board rather than relying only on headline frequency. Maintain symmetric routing where possible and use a quiet ground plane to minimize injected noise and supply-related jitter.

🖥️

High-Speed Digital Processor Clocking

The ICS571MT can buffer a source clock before it reaches a digital processor, FPGA fabric, or multiple sequential logic blocks. Its zero delay function is intended to compensate distribution-path delay, and its low-skew dual output can feed related clock domains from one input. Designers should still verify maximum frequency, propagation delay, output jitter, and setup/hold timing for the selected device speed grade. Keep the source-to-buffer and buffer-to-load paths short, and avoid using the buffer to correct arbitrary routing skew beyond its specified range.

📡

Synchronous Data Acquisition

The ICS571MT is applicable when an ADC, DAC, or data-capture front end requires two low-skew copies of the sampling clock. Its phase-noise performance and 160 MHz maximum frequency can support high-rate conversion systems operating at 3.3 V, provided the required sampling mode and converter clock limits are satisfied. Place the ZDB near the converter clock pins, use a continuous return path, and minimize clock-buffer input capacitance effects on the master oscillator. Validate aperture timing and interface timing together because low buffer phase noise does not remove converter-specific acquisition errors.

What is the ICS571MT?
The ICS571MT is a Renesas Electronics 160 MHz, 1:2, low-phase-noise zero delay buffer with CMOS inputs and two true CMOS outputs in an 8-pin SOIC. According to the manufacturer datasheet description, it integrates proprietary analog and digital phase adjustment to reduce propagation-delay differences through clock distribution networks. Its two outputs provide non-inverted clock copies for systems that need more drive or lower skew than a direct source connection can provide.
What is the maximum operating frequency of ICS571MT?
The ICS571MT supports input clock frequencies up to 160 MHz at 3.3 V. The manufacturer describes the device as a high-speed zero delay buffer with low phase noise, high output drive, and two true outputs. The maximum frequency is a headline operating limit, but the usable bandwidth in a finished system still depends on clock edge rate, PCB trace length, loading, source termination, and receiver setup and hold requirements.
Where can I download the ICS571MT datasheet PDF?
The ICS571MT datasheet PDF is available through the Renesas/Integrated Circuit Systems documentation listed on the product’s datasheet page, with an accessible mirror at the AllDataSheet link on this page. The document identifies the ICS571MT as a low-phase-noise zero delay buffer and provides its feature description and application information. Review the pin-description table and electrical characteristics in the manufacturer datasheet before assigning PCB signals or selecting supply voltage.
Where can I find the ICS571MT pinout?
The ICS571MT uses an 8-pin SOIC, and its exact numbered pin assignments are defined by the manufacturer datasheet. Use the pin-description table in that document when connecting the clock input, two true outputs, supply rails, and ground. Pin names are not reproduced on this page because the available product records confirm the 8-pin SOIC package but do not expose the complete numbered pin table.
Can the ICS571MT multiply a clock frequency?
Yes, the ICS571MT can function as a low-phase-noise times-two multiplier according to the manufacturer feature description. Its normal architecture is described as a one-input, two-output device with a 1:2 input-to-output ratio, so the exact operating configuration must be checked against the datasheet timing diagrams and truth information. Validate output frequency, duty-cycle distortion, and settling behavior in the intended circuit before using it as a frequency synthesizer.
What is the difference between ICS571MT and ICS574MLF?
The ICS571MT is a 160 MHz, 1:2 zero delay buffer, while the ICS574MLF is identified in the cross-reference record as a PLL-based clock driver with two true CMOS outputs in an 8-pin SOIC. Both are identified as lead-free PDSO-8 devices, and the comparison source describes their terminals and packages as consistent. Before replacement, verify propagation delay, skew, phase adjustment, supply range, and application-specific timing in the manufacturer documentation.
When should I choose ICS571MT over a PLL clock driver?
Choose the ICS571MT when the design needs a low-noise clock copy or 1:2 distribution function rather than synthesis of a new output frequency. Its zero delay architecture is intended to compensate clock-distribution delay while preserving a 160 MHz maximum input frequency and providing two true outputs. A PLL-based driver may be preferable when programmable multiplication, division, jitter filtering, or a different output ratio is required.
Is ICS571MT suitable for high-speed digital and communications clocks?
The ICS571MT is suitable for many high-speed digital and communications clock-distribution tasks because it supports up to 160 MHz, provides high output drive, and offers low-skew true outputs. The device can distribute a common clock to two receiver domains in telecommunications, networking, industrial, and test systems. Suitability still depends on edge-rate margin, return-path design, loading, and the receiver’s timing specification.
What can replace the ICS571MT?
The ICS574MLF and ICS574MLFT are verified cross-reference candidates for the ICS571MT because they use a lead-free 8-pin SOIC and provide two true CMOS clock outputs. They are same-family Renesas candidates, but the manufacturer’s function descriptions differ because the ICS574 parts are identified as PLL-based clock drivers. Verify pin-level timing, frequency range, supply requirements, and PLL behavior before approving either part as a production drop-in replacement.
What is the best Renesas equivalent for ICS571MT?
The closest identified Renesas equivalents are the ICS574MLF and ICS574MLFT in the same lead-free 8-pin SOIC format. They differ functionally by being PLL-based clock drivers, so they are most appropriate where a PLL driver can satisfy the board’s frequency-generation and jitter requirements. A qualified replacement must preserve the intended 1:2 zero-delay behavior, two true outputs, clock polarity, supply voltage, and timing margin.
Where can I buy ICS571MT online?
Use the Request a Quote form on this page to request the current ICS571MT price, stock position, lead time, and minimum order quantity. The quote team can confirm the exact 8-pin SOIC ordering code and current channel availability for the Renesas Electronics ICS571MT. This avoids publishing a stale price or treating a general distributor listing as a guaranteed allocation.
What is the price of ICS571MT?
The current ICS571MT price depends on order quantity, sourcing channel, and component condition. Submit a request through the Request a Quote form on this page for a current quotation and quantity breaks. Pricing should be confirmed for the exact ICS571MT suffix and package, rather than inferred from family-level listings or from another member of the 570 clock-driver series.
What is the lead time and stock status of ICS571MT?
Request the current lead time, stock quantity, and minimum order quantity through the Request a Quote form on this page. The visible product records identify ICS571MT as available from multiple channels, but they do not establish a reliable current allocation for the exact MPN. A dated quotation and stock confirmation should therefore be required before committing a production schedule.
How should I layout a PCB around the ICS571MT?
Place the ICS571MT close to the clock receiver or split point, and route each clock output as a short, continuous trace over a continuous reference plane. Keep the ground and supply connections short, use appropriate source termination, and avoid stubs, vias, and long parallel paths beneath the clock network. Validate edge-rate degradation and timing margin with the actual load, connector, and PCB stack-up.
What are the key specifications of ICS571MT that engineers should know?
The key ICS571MT specifications are a 160 MHz maximum input frequency at 3.3 V, one CMOS input, two true CMOS outputs, a 1:2 input-to-output ratio, PLL capability, low phase noise, low-skew outputs, high output drive, and an 8-pin SOIC package. The manufacturer reports phase noise better than -100 dBc/Hz from 10 kHz to 1 MHz offset. These parameters place the part between a clock distributor and a phase-compensating timing device.

Mühendislik referans verileri: ICS571MT — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the ICS571MT when a system needs to distribute one CMOS clock to two true outputs at up to 160 MHz while compensating distribution delay and preserving low phase noise. It is especially suitable for deterministic telecommunications, industrial, acquisition, and digital-processing clock trees where two related domains must receive aligned non-inverted clocks. The ICS574MLF and ICS574MLFT are appropriate alternatives when a lead-free 8-pin SOIC PLL-based clock driver is acceptable, but their PLL behavior and timing parameters must be checked rather than assumed identical. The ICS570MT, ICS571ML, and ICS572MT are same-family candidates that may share the footprint, yet their frequency ratings, ratios, and pin functions require direct comparison. For any substitution, validate supply range, propagation delay, output skew, jitter, phase noise, clock polarity, and receiver timing on the final PCB before production release.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün ICS570MT ICS574MLF ICS574MLFT ICS571ML ICS572MT
Package 8-pin SOIC, 3.90 mm width 8-pin SOIC Lead-free PDSO-8 Lead-free PDSO-8 8-pin SOIC 8-pin SOIC
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Device Function Fanout buffer (distribution), zero delay buffer 570-series clock driver PLL-based clock driver PLL-based clock driver 571-series clock driver 570-series clock driver

Ana Farklılayıcılar

  • Fixed zero delay function (karşılaştırma:ICS574MLF)
  • Explicit maximum input frequency (karşılaştırma:ICS574MLFT)
  • Low phase-noise fanout architecture (karşılaştırma:ICS570MT)

Tasarım Notları

Place the ICS571MT near the point where the clock splits or near the most timing-sensitive receiver. Route both outputs over a continuous ground plane, keep the paths short, and avoid test pads, long stubs, and unnecessary layer transitions. Maintain approximately matched geometry when low skew is important, because trace-length differences and load capacitance can reduce the benefit obtained from the zero delay architecture.

Verify the complete clock path at the actual edge rate rather than judging the circuit by the 160 MHz carrier frequency alone. Check source impedance, output drive, receiver capacitance, trace loss, and termination using the final PCB stack-up. An underdamped or heavily capacitive output can exhibit overshoot, ringing, or threshold-crossing distortion that consumes receiver timing margin even when the nominal clock frequency remains within specification.

Use the manufacturer-specified operating supply and local bypass arrangement. Place input and output decoupling capacitors close to their associated pins, with the shortest possible ground-return path, and keep the clock device away from inductors, switching regulators, and high-current return paths. Confirm ground bounce and supply ripple at the pins under maximum output-drive and maximum-frequency conditions, because both can translate into clock jitter or an apparent phase-noise increase.

Do not treat a same-package cross-reference as a qualified substitute without checking propagation delay, output skew, jitter, phase-noise limits, supply range, and enable or output-control behavior. The ICS574MLF and ICS574MLFT are PLL-based clock drivers rather than exact functional copies of the ICS571MT. Validate the replacement using the manufacturer timing diagrams and the receiver’s setup-and-hold requirements before releasing it to production.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Yes
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The cross-reference record identifies the ICS571MT and the ICS574 candidates as lead-free devices. RoHS, REACH, halogen-free, and conflict-minerals status are not explicitly confirmed in the available product records.

Veri doğrulanma tarihi: 2026-11-11 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

ICS571MT datasheet ICS571MT pinout ICS571MT datasheet pdf ICS571MT equivalent ICS571MT replacement ICS571MT cross reference ICS571MT vs ICS574MLF ICS571MT price ICS571MT stock Renesas ICS571MT ICS571MT 160MHz zero delay buffer ICS571MT SOIC-8 ICS571MT clock fanout ICS571MT application circuit ICS571MT phase noise

İlgili Bileşenler ve Terimler

Renesas Electronics ICS571MT ICS570MT ICS574MLF ICS574MLFT ICS571ML ICS572MT zero delay buffer ZDB fanout buffer clock buffer clock and timing IC semiconductor CMOS phase noise output skew propagation delay 160 MHz 3.3 V 1:2 clock fanout PLL 8-pin SOIC PDSO-8 surface mount lead-free
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle