ICS571MT - 160MHz 1:2 Zero Delay Buffer | Renesas Electronics
MPN: ICS571MT ✓ 啟用中ICS571MT 概覽
A zero delay buffer is a clock-management IC that uses a phase-adjustable buffer architecture to compensate for propagation delay introduced by clock distribution networks. Within the broader hierarchy, it is a fanout buffer, then a clock buffer, then a clock and timing IC, and finally a semiconductor. By placing a ZDB close to a clock-consuming circuit, designers can reduce the timing penalty associated with board traces, while a 1:2 ratio allows one source clock to feed two independent loads.
Key characteristics include a maximum frequency of 160 MHz, CMOS inputs, CMOS outputs, PLL capability, one input circuit, two true outputs, and an input-to-output ratio of 1:2. The ICS571MT can also operate as a low-phase-noise frequency multiplier according to the manufacturer description. Its low-skew outputs are useful when related clocks must remain closely aligned, and phase noise better than -100 dBc/Hz is described from 10 kHz to 1 MHz offset from the carrier under the cited operating conditions.
The typical application is clock fanout in telecommunications, networking, industrial control, test and measurement, and digital processing systems. It can distribute a common clock to two domains, provide clock buffering between a source and a load, or provide two low-skew copies of a reference signal. The 8-pin SOIC package supports conventional surface-mount assembly and is easier to handle than a fine-pitch BGA package.
Designers should maintain short, impedance-controlled clock traces, use a ground reference close to the device, and verify source and load termination against the clock edge rate. A nominal maximum frequency does not guarantee acceptable timing margin in every board environment; rise time, loading, return paths, and available setup and hold time must be evaluated together.
This page combines the manufacturer-described operating characteristics, packaging information, application guidance, and verified drop-in candidates to support faster component evaluation and board-level sourcing decisions.
直接替換替代品,適用於 ICS571MT — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
ICS570MT
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ICS574MLF
✅ 直接替換📋 參考替代品(不在目錄中)
ICS574MLFT
✅ 直接替換📋 參考替代品(不在目錄中)
ICS571ML
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ICS572MT
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ICS571MT 規格
| Device Type | Fanout buffer (distribution), zero delay buffer IC |
| Maximum Frequency | 160 MHz |
| Number of Circuits | 1 |
| Input-to-Output Ratio | 1:2 |
| Input Logic Type | CMOS |
| Output Logic Type | CMOS |
| Number of True Outputs | 2 |
| PLL | Yes |
| Architecture | Analog/digital phase-adjustable zero delay buffer |
| Input Clock Frequency at 3.3 V | Up to 160 MHz |
| Phase Noise | Better than -100 dBc/Hz from 10 kHz to 1 MHz offset from carrier |
| 封裝 | 8-pin SOIC, 3.90 mm width |
| 安裝類型 | Surface mount |
| Lead-Free Status | Lead free |
| Output Drive | High output drive |
ICS571MT 8-pin soic, 3.90 mm width 腳位配置指南
ICS571MT(8-pin soic, 3.90 mm width 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ICS571MT.
請參閱 資料表 以查看完整腳位配置。
典型應用
ICS571MT 適用於 6 應用s: Telecommunications Clock Fanout, Networking and Ethernet Clock Distribution, Industrial Control Clock Trees, Test and Measurement Instrumentation, High-Speed Digital Processor Clocking, Synchronous Data Acquisition.
Telecommunications Clock Fanout
The ICS571MT is appropriate for distributing a common clock to two telecommunications or data-processing domains while maintaining low phase noise and low output skew. Its 160 MHz maximum input frequency at 3.3 V provides useful margin for demanding digital logic, while the two true CMOS outputs avoid inversion-related phase surprises. Place the buffer near the clock split or receiver branches, provide a continuous ground reference, and terminate each output according to its actual edge rate and load. The principal trade-off is that a zero delay buffer is not a programmable PLL, so a design requiring synthesized frequencies or independent ratios should use a PLL clock driver instead.
推薦
Networking and Ethernet Clock Distribution
The ICS571MT can fan out a 160 MHz-class source clock into two true CMOS branches used by network controllers, physical-layer devices, or fabric clocking logic. Low-skew outputs help retain alignment between related destinations, and the 1:2 ratio fits designs where two loads share one source. The design should minimize trace mismatch and provide a low-impedance reference plane because skew from unequal routing can consume the available setup margin. Confirm the receiver thresholds, clock edge rate, and supply voltage before release, especially where the source already provides a strong buffer.
推薦
Industrial Control Clock Trees
For industrial control systems, the ICS571MT provides two non-inverted CMOS clock outputs from one input, reducing the loading burden on an upstream oscillator or controller. Its high output drive is useful when driving local logic through a short PCB network, while the low-phase-noise architecture supports deterministic timing in acquisition and control paths. Keep the device away from high-current switching nodes, provide local supply bypassing, and account for temperature and loading changes during worst-case timing analysis. If the system must generate unrelated frequencies for multiple domains, a PLL-based clock driver offers more flexibility than this fixed-ratio buffer.
推薦
Test and Measurement Instrumentation
The ICS571MT is useful in test and measurement equipment where one precision reference must reach two acquisition, conversion, or processing paths with closely related timing. The 160 MHz upper frequency supports high-speed digital backplanes, and the two true outputs can preserve clock polarity across both destinations. For laboratory-grade performance, characterize phase noise, edge rate, output jitter, and temperature drift on the final board rather than relying only on headline frequency. Maintain symmetric routing where possible and use a quiet ground plane to minimize injected noise and supply-related jitter.
推薦
High-Speed Digital Processor Clocking
The ICS571MT can buffer a source clock before it reaches a digital processor, FPGA fabric, or multiple sequential logic blocks. Its zero delay function is intended to compensate distribution-path delay, and its low-skew dual output can feed related clock domains from one input. Designers should still verify maximum frequency, propagation delay, output jitter, and setup/hold timing for the selected device speed grade. Keep the source-to-buffer and buffer-to-load paths short, and avoid using the buffer to correct arbitrary routing skew beyond its specified range.
推薦
Synchronous Data Acquisition
The ICS571MT is applicable when an ADC, DAC, or data-capture front end requires two low-skew copies of the sampling clock. Its phase-noise performance and 160 MHz maximum frequency can support high-rate conversion systems operating at 3.3 V, provided the required sampling mode and converter clock limits are satisfied. Place the ZDB near the converter clock pins, use a continuous return path, and minimize clock-buffer input capacitance effects on the master oscillator. Validate aperture timing and interface timing together because low buffer phase noise does not remove converter-specific acquisition errors.
推薦
推薦產品摘要
工程參考資料,適用於 ICS571MT — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ICS570MT | ICS574MLF | ICS574MLFT | ICS571ML | ICS572MT |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC, 3.90 mm width | 8-pin SOIC | Lead-free PDSO-8 | Lead-free PDSO-8 | 8-pin SOIC | 8-pin SOIC |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Device Function | Fanout buffer (distribution), zero delay buffer | 570-series clock driver | PLL-based clock driver | PLL-based clock driver | 571-series clock driver | 570-series clock driver |
主要差異化特點
- Fixed zero delay function (對比ICS574MLF)
- Explicit maximum input frequency (對比ICS574MLFT)
- Low phase-noise fanout architecture (對比ICS570MT)
設計說明
Place the ICS571MT near the point where the clock splits or near the most timing-sensitive receiver. Route both outputs over a continuous ground plane, keep the paths short, and avoid test pads, long stubs, and unnecessary layer transitions. Maintain approximately matched geometry when low skew is important, because trace-length differences and load capacitance can reduce the benefit obtained from the zero delay architecture.
Verify the complete clock path at the actual edge rate rather than judging the circuit by the 160 MHz carrier frequency alone. Check source impedance, output drive, receiver capacitance, trace loss, and termination using the final PCB stack-up. An underdamped or heavily capacitive output can exhibit overshoot, ringing, or threshold-crossing distortion that consumes receiver timing margin even when the nominal clock frequency remains within specification.
Use the manufacturer-specified operating supply and local bypass arrangement. Place input and output decoupling capacitors close to their associated pins, with the shortest possible ground-return path, and keep the clock device away from inductors, switching regulators, and high-current return paths. Confirm ground bounce and supply ripple at the pins under maximum output-drive and maximum-frequency conditions, because both can translate into clock jitter or an apparent phase-noise increase.
Do not treat a same-package cross-reference as a qualified substitute without checking propagation delay, output skew, jitter, phase-noise limits, supply range, and enable or output-control behavior. The ICS574MLF and ICS574MLFT are PLL-based clock drivers rather than exact functional copies of the ICS571MT. Validate the replacement using the manufacturer timing diagrams and the receiver’s setup-and-hold requirements before releasing it to production.
合規資訊
The cross-reference record identifies the ICS571MT and the ICS574 candidates as lead-free devices. RoHS, REACH, halogen-free, and conflict-minerals status are not explicitly confirmed in the available product records.