ISL8483EIP - 5V ESD-Protected RS-485/RS-422 Transceiver | Renesas
料号: ISL8483EIP ✓ 量产中ISL8483EIP 概述
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over cables and longer distances. RS-422 emphasizes point-to-point, balanced signaling, while RS-485 supports multidrop buses and driver-enable control. This device bridges the single-ended digital domain and the differential bus, placing it within the interface IC, communication IC, and semiconductor hierarchy.
Key features include one half-duplex transmitter, one receiver, 5 V operation, and device-level ESD protection of ±15 kV. Driver short-circuit current limits help protect the outputs when a bus node is driven against another active node. Thermal shutdown adds a secondary protection mechanism when sustained contention or abnormal loading raises internal dissipation.
The ISL8483 family combines BiCMOS implementation with low-power operation and two signal-rate options identified by the ISL8483 and ISL8485 family members. The E version adds enhanced ESD protection, while the receiver and driver control arrangement supports implementation of half-duplex nodes. Exact data rate, propagation delay, slew rate, and common-mode limits should be selected from the family datasheet for the intended bus topology.
Typical uses include industrial RS-485 field buses, building automation equipment, factory data links, RS-422 point-to-point links, and industrial control modules. The device is particularly suitable when a design needs a single transceiver, balanced differential signaling, 5 V supply operation, and reinforced ESD protection near a connector or externally accessible cable.
PCB implementation should keep the transceiver close to the connector, route the differential pair as a tightly matched pair, and provide a low-impedance return path. Decoupling capacitors should connect to the ground plane with short traces, and unused or unused-condition control inputs must be driven to defined logic levels to prevent an indeterminate bus state.
直接替换替代料: ISL8483EIP ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ISL8483EIP (相同外形与封装尺寸) ——差异在于 Mounting Type, Package, ESD Protection, Product Type.
ISL8483IP
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →ISL8483CP
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
ISL8485EIP
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
ISL8483EIP 规格参数
| Device Type | Single RS-485/RS-422 transceiver |
| Transmitter and Receiver Count | 1 transmitter and 1 receiver |
| 电源电压 | 5 V |
| ESD Protection | ±15 kV |
| Supported Standards | RS-485 and RS-422 |
| Implementation Technology | BiCMOS |
| Driver Short-Circuit Protection | On-chip short-circuit current limiting |
| Thermal Protection | On-chip thermal shutdown |
| 封装 | 8-pin PDIP |
| 引脚数量 | 8 pins |
| 安装类型 | Through-hole |
| RoHS 状态 | Compliant |
ISL8483EIP 引脚配置
| 引脚 1 | ROUT — Receiver output |
| 引脚 2 | RE — Receiver enable input |
| 引脚 3 | DE — Driver enable input |
| 引脚 4 | DI — Driver input |
| 引脚 5 | GND — Ground |
| 引脚 6 | A — Differential driver output A |
| 引脚 7 | B — Differential driver output B |
| 引脚 8 | VCC — Positive supply voltage |
典型应用
ISL8483EIP 适用于 6 应用s: Industrial RS-485 Field Bus, RS-422 Point-to-Point Link, Building Automation Controller, Factory Data Acquisition Equipment, Industrial Control Module, External Communication Connector.
Industrial RS-485 Field Bus
The ISL8483EIP is appropriate for a half-duplex industrial RS-485 node because it combines one transmitter, one receiver, 5 V operation, and ±15 kV ESD protection in an 8-pin PDIP package. Place the transceiver between the controller UART and the isolated or non-isolated bus connector, using the enable controls to prevent more than one node from driving the bus simultaneously. Its short-circuit current limiting and thermal shutdown improve robustness during contention. The exact maximum data rate and bus length must be selected from the datasheet for the installed cable, termination, topology, and common-mode environment.
推荐
RS-422 Point-to-Point Link
The ISL8483EIP can terminate a point-to-point RS-422 link when the design uses a single balanced channel and 5 V interface voltage. The transmitter converts the UART logic signal into differential bus levels, while the receiver returns a single-ended signal to the controller. Driver-enable and receiver-enable pins support controlled half-duplex operation where both directions are not required simultaneously. The ±15 kV ESD rating is valuable near an external connector, although cable routing, grounding, and the exact receiver thresholds remain critical to reliable communication.
推荐
Building Automation Controller
Building automation controllers often distribute sensor and actuator commands over RS-485 wiring that may pass near doors, lighting panels, and maintenance interfaces. The ISL8483EIP offers a compact 8-pin PDIP implementation with 5 V operation and ±15 kV protection against ESD encountered at external wiring points. Its one-driver, one-receiver configuration is suitable for a half-duplex controller node, while short-circuit limiting and thermal shutdown help the interface survive bus conflicts. Final qualification should include the controller's UART timing, termination strategy, grounding arrangement, and applicable building-system EMC requirements.
推荐
Factory Data Acquisition Equipment
Factory acquisition equipment can use the ISL8483EIP to connect a controller to remote sensors, counters, or programmable instruments over a balanced RS-485 bus. The transceiver's single transmitter and receiver reduce the interface footprint, while the 5 V supply requirement supports integration into conventional embedded control hardware. ESD protection is important when acquisition modules connect to long cables or user-accessible equipment. Designers should still verify propagation delay against the required polling rate, account for bus-stub reflections, and provide the termination and biasing required by the selected network topology.
推荐
Industrial Control Module
The ISL8483EIP is suitable for a compact industrial control module that exchanges commands and diagnostic data over a wired RS-485 or RS-422 link. Its through-hole 8-pin PDIP package supports conventional plated-through-hole assembly and rework, while the 5 V operating rail simplifies integration with logic powered from the same supply. Connecting the transceiver close to the field connector helps direct ESD currents away from sensitive controller circuitry. The control firmware should enforce bus-enable arbitration, and the hardware design should verify receiver fail-safe behavior, driver loading, and thermal performance at the intended ambient temperature.
推荐
External Communication Connector
An external communication connector exposed to cables and service access is a common ESD entry point for electronics. Placing the ISL8483EIP near that connector provides ±15 kV ESD protection on the driver outputs and receiver inputs, reducing stress on the controller and isolating the digital logic from the balanced bus. The 8-pin PDIP package offers a straightforward through-hole implementation, and the short-circuit-limited driver helps manage accidental bus conflicts. For reliable protection, use the shortest practical route to the connector, maintain a continuous ground reference, avoid stubs, and follow the datasheet's recommended bus-side layout.
推荐
推荐产品汇总
工程参考数据: ISL8483EIP ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ISL8483IP | ISL8483CP | ISL8485EIP |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Transmitter and Receiver Count | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V |
| Supported Standards | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
关键差异点
- Enhanced ESD protection in the E-version (对比 ISL8483IP)
- Direct same-package family interchange (对比 ISL8485EIP)
- Choice of signal-rate behavior without changing the footprint (对比 ISL8483CP)
设计说明
Place the ISL8483EIP close to the external connector so ESD and cable-transient currents are intercepted before reaching the controller. Route the A and B conductors as a matched differential pair over a continuous ground plane, keep the pair length uniform, and avoid stubs. Connect the transceiver ground pins directly to the ground plane with short paths rather than routing return current through the differential pair.
Decouple the 5 V supply at the transceiver with a short trace to the ground plane. Keep the supply and ground connections away from the A and B bus traces to minimize differential crosstalk. Provide local bypass capacitance according to the family datasheet and ensure the supply source can support the transmitter's enabled load and the receiver's operating current without excessive rail droop during data transmission.
Do not allow more than one node to enable its driver simultaneously. The RS-485 bus can sustain contention, and the ISL8483EIP includes short-circuit current limiting and thermal shutdown, but sustained contention still wastes power and creates thermal stress. Use deterministic enable control in firmware, define a safe state for the enable inputs during reset, and avoid floating control or logic inputs.
Choose the family variant according to the required edge rate rather than selecting solely by maximum data rate. Faster slew rates can reduce cable-related signal loss but may increase emissions and common-mode disturbance; a slew-rate-limited version can be preferable on slower or noisier industrial wiring. Confirm propagation delay, receiver threshold, bus loading, termination, and biasing together before freezing the PCB design.
Thermal shutdown is a fault-protection feature rather than a substitute for correct bus arbitration. Verify continuous transmitter current, ambient temperature, and package dissipation for the selected operating mode. If the driver can remain enabled during repeated bus conflicts, consider system-level mitigation such as controlled shutdown, fault monitoring, or a physical bus design that prevents simultaneous active drivers.
合规信息
The product listing identifies the ISL8483EIP as RoHS compliant. No additional REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification information is stated for this exact suffix.