KSZ8775CLXIC 5-Port 10/100 Ethernet Switch | Microchip
MPN: KSZ8775CLXIC ✓ AktifKSZ8775CLXIC Genel Bakış
An Ethernet switch is a network-interface integrated circuit that forwards Ethernet frames between a processor, network interface controllers, and physical-layer devices. The KSZ8775 belongs to the managed-switch hierarchy within Ethernet controllers, interface ICs, and broader networking semiconductors. Its Layer 2 architecture reduces the need for discrete switching components while supporting cost-sensitive embedded, industrial, and communications equipment.
The KSZ8775CLXIC's principal advantages include five integrated ports, support for copper links at 10/100 Mbps, and flexible host-facing interfaces on the two upper ports. Its automatic power-saving function helps reduce unnecessary activity in embedded systems, while the wake-up function supports designs that must resume network operation on demand. Power-up and reset configuration provides a deterministic hardware initialization path for systems without a complex manager-boot sequence.
Port 4 is identified as an RMII interface, while Port 5 can use RGMII, GMII, or RMII. These selectable interfaces make the device adaptable to processors, FPGAs, and communication controllers with different host-bus requirements. The combination of three copper-facing ports and two configurable upper-port interfaces creates a compact Ethernet switching hub around a single 3.3 V device.
Typical applications include industrial Ethernet gateways, embedded control systems, factory equipment, network adapters, communications appliances, and compact embedded Ethernet hubs. The device is especially useful when a design needs several 10/100 copper connections plus one or two processor-facing interfaces without implementing a discrete switching layer.
PCB design should preserve pin-compatible placement of the 80-pin LQFP footprint and route each copper-port differential pair according to the manufacturer's layout guidance. Keep the 3.3 V supply and decoupling network close to the device, and provide clean interfaces to the selected processor or FPGA. Because an Ethernet switch integrates high-speed digital links and magnetics-facing circuitry, controlled return paths and disciplined differential-pair routing are central to reliable operation.
This page consolidates the device's port configuration, interface options, sourcing information, practical design guidance, and verified drop-in comparison. The 80-pin LQFP outline and 3.3 V operation make the KSZ8775CLXIC a focused choice for compact Layer 2 switching designs that need multiple 10/100 Mbps copper ports and flexible host connectivity.
Drop-in alternatifler için KSZ8775CLXIC — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
KSZ8775CLXCC
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →KSZ8775CLXIC Maksimum Değerlendirmeler & Elektriksel Özellikler
| Device Type | Layer 2-managed Ethernet switch |
| Total Port Count | 5 ports |
| Copper Port Data Rate | 10/100 Mbps |
| Dedicated 10/100 Mbps Copper Ports | 3 ports |
| Port 4 Interface | RMII |
| Port 5 Interfaces | RGMII, GMII, or RMII |
| Besleme Gerilimi | 3.3 V |
| Wake-Up Function | Supported |
| Automatic Power Saving | Supported |
| Configuration Method | Power-up and reset configuration |
| Switching Layer | Layer 2 |
| Paket | 80-pin LQFP, 10 mm x 10 mm |
| Montaj Türü | Surface mount |
| Ethernet Standard Support | 10/100 Base-T/TX |
| RoHS Durumu | Compliant |
KSZ8775CLXIC 80-pin lqfp, 10 mm x 10 mm Pin Yapısı Kılavuzu
KSZ8775CLXIC (80-pin lqfp, 10 mm x 10 mm paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: KSZ8775CLXIC.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
KSZ8775CLXIC için uygundur 6 uygulamas: Industrial Ethernet Gateway, Embedded Ethernet Hub, Factory Equipment Network Controller, Network Appliance Front Panel, FPGA-Based Communication System, Low-Power Embedded Network Node.
Industrial Ethernet Gateway
The KSZ8775CLXIC fits an industrial Ethernet gateway that must combine three 10/100 Mbps copper links with a processor-facing data path. The three integrated copper ports can connect field equipment, a local controller, or diagnostic equipment, while Port 4 RMII provides a compact connection to a host processor. Port 5 can select RGMII, GMII, or RMII to accommodate a different host or FPGA interface. Operating from 3.3 V simplifies integration with contemporary embedded processors. The 80-pin LQFP package keeps the switching section compact, but designers should implement the manufacturer's differential-pair and decoupling layout, verify startup behavior, and confirm that the exact temperature and qualification grade covers the industrial environment.
Önerilen
Embedded Ethernet Hub
The KSZ8775CLXIC supports a compact embedded Ethernet hub in which multiple 10/100 Mbps endpoints share access to a host processor. Three copper ports can serve sensors, programmable controllers, or service interfaces, while the configurable upper ports provide the required host bandwidth and electrical interface. RMII is useful where a low-pin-count host connection is preferred, whereas RGMII or GMII can serve designs requiring a wider parallel interface. The device's Layer 2-managed architecture reduces the external switching component count. Designers should account for endpoint cable reach, magnetics requirements, firmware-based configuration, and wake-up behavior. The automatic power-saving and wake-up functions are particularly valuable in embedded systems that spend substantial time idle but must reconnect reliably after a network service event.
Önerilen
Factory Equipment Network Controller
The KSZ8775CLXIC is useful in factory equipment that needs a compact Ethernet connection hub for machine control, diagnostics, and service access. Three 10/100 Mbps copper ports can connect a controller, engineering workstation, and remote I/O device without adding a separate switching chipset. A host processor can attach through the Port 4 RMII interface, while Port 5 can be configured for RGMII, GMII, or RMII according to the processor interface architecture. Because the KSZ8775 operates from 3.3 V, it can share a conventional embedded supply rail with supporting digital devices. The design must provide suitable copper magnetics, robust grounding, controlled differential routing, and correct power-up configuration. Confirm the industrial temperature grade and qualification requirements before deployment in a factory environment.
Önerilen
Network Appliance Front Panel
The KSZ8775CLXIC can organize front-panel Ethernet connections in a compact network appliance, communications controller, or service gateway. Three copper ports provide links to a management network, an upstream equipment connection, and a local service interface, while Port 4 RMII and configurable Port 5 connectivity link the switch to an embedded host. The Layer 2-managed five-port architecture supports cost-conscious systems that need centralized switching without a complex multi-gigabit PHY arrangement. Automatic power saving can reduce link activity during idle periods, while wake-up supports recovery from low-power states. Firmware should initialize the device through the documented power-up and reset configuration path and verify interface timing after wake-up. The 80-pin LQFP footprint requires careful fanout and differential-pair routing in compact appliance designs.
Önerilen
FPGA-Based Communication System
The KSZ8775CLXIC fits an FPGA-based communication system where an FPGA needs both network-facing copper links and a flexible processor-side interface. The three 10/100 Mbps copper ports serve external links, while Port 4 RMII offers a straightforward low-pin-count host connection and Port 5 can be selected among RGMII, GMII, or RMII. This allows the design to reserve the upper-port interface that best matches the FPGA logic and clocking resources. The 3.3 V device operates from the same supply class commonly used by embedded communication equipment. Designers should use the manufacturer's pin and timing documentation to constrain interfaces, preserve a continuous ground plane, and implement the recommended Ethernet trace geometry. Startup configuration should be coordinated with FPGA initialization so that attached PHY or processor interfaces begin in a controlled state.
Önerilen
Low-Power Embedded Network Node
The KSZ8775CLXIC supports low-power embedded network nodes that need several 10/100 Mbps links but cannot justify a large discrete switching design. Three copper ports can support local service, control, and monitoring connections, while Port 4 RMII offers an efficient path to a low-power microcontroller or application processor. Port 5 can use RMII, RGMII, or GMII when a host requires a wider interface. Automatic power saving reduces activity on unused links, and the wake-up function allows the system to reactivate network communication after an idle event. The correct power-management policy must be coordinated with the host and attached PHYs to avoid link flapping or interface synchronization errors. Decoupling placement, return-path continuity, and magnetics implementation remain critical to reliable Ethernet performance.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: KSZ8775CLXIC — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | KSZ8775CLXCC |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 80-LQFP (10 mm x 10 mm) | 80-LQFP (10 mm x 10 mm) |
| Device Type | Layer 2-managed Ethernet switch | Layer 2-managed Ethernet switch |
| Total Port Count | 5 ports | 5 ports |
| Copper Port Data Rate | 10/100 Mbps | 10/100 Mbps |
| Dedicated 10/100 Mbps Copper Ports | 3 ports | 3 ports |
| Port 4 Interface | RMII | RMII |
| Port 5 Interfaces | RGMII, GMII, or RMII | RGMII, GMII, or RMII |
| Supply Voltage | 3.3 V | 3.3 V |
| Wake-Up Function | Supported | Supported |
| Automatic Power Saving | Supported | Supported |
| Power-Up and Reset Configuration | Supported | Supported |
Ana Farklılayıcılar
- Five-port integration in one 80-pin LQFP device (karşılaştırma:KSZ8775CLXCC)
- Flexible upper-port host connectivity (karşılaştırma:KSZ8775CLXCC)
- Embedded power-state support (karşılaştırma:KSZ8775CLXCC)
Tasarım Notları
Create the PCB land pattern from the manufacturer's 80-pin LQFP drawing and verify it against the 10 mm by 10 mm body size and stated lead pitch. Place input and output decoupling capacitors adjacent to their corresponding supply pins, provide a continuous ground reference beneath the switching section, and preserve the manufacturer-recommended geometry for all 10/100 Mbps differential pairs. Check the copper-port and host-interface layout together rather than optimizing either group independently.
RGMII, GMII, and RMII have different clocking and timing requirements, so select one Port 5 configuration early in the architecture. Route the selected interface as a coordinated signal group, maintain the required return path, and apply the manufacturer's interface timing and layout constraints. Coordinate reset and power-up configuration with the host or FPGA so that all connected interfaces begin from a defined state and recover coherently after wake-up.
The device operates from 3.3 V, so the supply network must remain within the electrical limits documented by Microchip while providing low-impedance decoupling for switching activity. Use separate local bypass paths where recommended and keep high-current Ethernet connections away from sensitive host-interface routing. Validate startup current and worst-case activity in the complete system, then confirm that the chosen temperature grade and package dissipation capability suit the enclosure temperature.
Do not treat the I and C ordering suffixes as automatically interchangeable. Before substituting KSZ8775CLXCC for KSZ8775CLXIC, compare the manufacturer ordering table for temperature range, qualification, lifecycle, and configuration differences. Also verify that the attached magnetics or PHYs match the port arrangement and that Port 4 and Port 5 are assigned to interfaces supported by the host processor. A matching package alone does not establish complete system compatibility.
Uyumluluk Bilgisi
The 80-pin LQFP listing identifies the device as RoHS compliant. No explicit REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was identified, so those fields remain unknown.