LAN91C111-NC 10/100 Ethernet MAC/PHY | Microchip Technology
MPN: LAN91C111-NC ✗ Son Kullanım ZamanıLAN91C111-NC Genel Bakış
An Ethernet MAC-and-PHY controller provides the bridge between a host processor and a physical network connection. The MAC manages frame handling and CSMA/CD access, while the integrated PHY handles the physical signaling required for 10BASE-T or 100BASE-TX links. Integrating both functions into one device reduces component count and allows a host processor to connect to copper Ethernet without requiring a separate transceiver.
The LAN91C111-NC supports data rates of 10 Mbps and 100 Mbps and implements the MAC and PHY portions of the CSMA/CD protocol. Its host interface can operate with 32-bit, 16-bit, or 8-bit data widths, helping the device accommodate processors with different bus capabilities. The internal MII connection between the MAC and PHY helps maintain throughput without using a separate external PHY bus.
Internal transmit and receive FIFO memory is dynamically configurable and totals 8 KB. This buffering allows the host interface and Ethernet network activity to proceed at different effective rates, improving tolerance of host-bus access intervals. The MII interface also provides a standardized connection for additional physical-layer equipment and simplifies integration with related network-interface circuitry.
Typical uses include industrial embedded systems, factory automation equipment, building controls, test equipment, print controllers, and compact embedded servers. A 100 Mbps link provides sufficient bandwidth for supervisory data, configuration traffic, telemetry, and moderate local file transfer. The selectable host-bus width is especially useful when adapting the controller to legacy parallel processor buses.
The principal design task is matching the host-bus timing, interrupt structure, address mapping, and I/O voltage to the system processor. Place the device and its required external network components close together, route MII and host signals as controlled-impedance traces, and terminate unused inputs according to the manufacturer datasheet. Validate signal integrity and recovery behavior across the full set of line-rate and environmental conditions.
This product record combines the Ethernet function description, package details, sourcing guidance, practical PCB considerations, and application-specific engineering context. It also distinguishes the device from true pin-compatible alternatives by applying a strict same-package and pin-compatibility requirement rather than presenting merely similar Ethernet controllers.
Drop-in alternatifler için LAN91C111-NC — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
LAN91C111I-NU
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
LAN91C111-NC Özellikler
| Product Type | 10/100 Non-PCI Ethernet MAC and PHY Controller |
| Supported Data Rates | 10 Mbps and 100 Mbps |
| Host Interface Widths | 32-bit, 16-bit, and 8-bit |
| Internal Interface | MII |
| Protocol Support | CSMA/CD |
| Ethernet Standard | IEEE 802.3 |
| Physical Layer Modes | 10BASE-T and 100BASE-TX |
| Internal FIFO Memory | 8 KB |
| FIFO Configuration | Dynamically configurable transmit and receive |
| Supply Voltage Range | 2.97 V to 3.63 V |
| Paket | 128-pin TQFP, 14 mm x 14 mm |
| Montaj Türü | Surface mount |
| Device Classification | Mixed-signal analog/digital semiconductor |
LAN91C111-NC 128-pin tqfp, 14 mm x 14 mm Pin Yapısı Kılavuzu
LAN91C111-NC (128-pin tqfp, 14 mm x 14 mm paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: LAN91C111-NC.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
LAN91C111-NC için uygundur 6 uygulamas: Industrial Automation Controllers, Factory Monitoring Equipment, Building Control Systems, Embedded Test Instruments, Print and Network Peripherals, IoT Edge Gateways.
Industrial Automation Controllers
The LAN91C111-NC fits industrial automation controllers that must exchange commands, diagnostics, and sensor data over a 10/100 Mbps Ethernet link. Its integrated MAC and PHY reduce board area, while the selectable 8-bit, 16-bit, or 32-bit host interface can match the embedded processor bus. The internal 8 KB transmit and receive FIFO buffers help isolate Ethernet traffic from irregular processor access intervals. For industrial equipment, keep the Ethernet magnetics and controller layout away from high-current switching paths, and validate recovery across cable insertion, link interruption, and sustained traffic conditions.
Önerilen
Factory Monitoring Equipment
The LAN91C111-NC is suitable for monitoring equipment that reports measurements, alarms, and configuration data through an embedded Ethernet network. A 100 Mbps connection provides sufficient bandwidth for supervisory traffic without requiring a high-performance host processor. The device's non-PCI architecture permits use with microcontrollers and DSPs that expose a parallel host bus. Designers should confirm host-bus timing and interrupt latency in the system clock domain, and should test packet-buffer behavior when the network is continuously loaded while supervisory software periodically stalls its bus.
Building Control Systems
The LAN91C111-NC can support Ethernet-enabled building controllers for HVAC, access, lighting, and energy-management equipment. Its 10/100 Mbps capability is appropriate for supervisory command traffic, diagnostics, and configuration updates. The selectable host width allows integration with legacy 8-bit and 16-bit embedded controllers, while the integrated PHY reduces the external Ethernet interface footprint. In building installations, follow isolation and grounding recommendations for the network magnetics, provide controlled network-port routing, and verify reboot, link-flap, and offline behavior in the controller firmware.
Embedded Test Instruments
The LAN91C111-NC is appropriate for embedded test and measurement products that must upload results or accept remote-control commands through Ethernet. Its selectable host-bus width supports processor architectures with different parallel interfaces, and the 8 KB FIFO provides useful separation between frame processing and host transactions. The 100 Mbps mode supports moderate result transfers while 10 Mbps mode can serve management-only networks. For reliable laboratory operation, use the MII and host-bus timing information in the manufacturer datasheet, isolate the Ethernet section from analog or high-energy circuitry, and test sustained transfers rather than only short packet bursts.
Print and Network Peripherals
The LAN91C111-NC suits print controllers, compact network appliances, and legacy embedded peripherals that need an economical 10/100 Mbps Ethernet path. The device combines the MAC, PHY, MII connection, and FIFO in one package, reducing the number of components compared with a separated design. A narrow 8-bit or 16-bit host bus can connect to a resource-constrained controller while the FIFO absorbs short host-access stalls. Engineers should check DMA or interrupt handling, buffer ownership, and recovery from underrun conditions, and should avoid assuming that every newer controller supports the same register map.
IoT Edge Gateways
The LAN91C111-NC can serve as the wired Ethernet interface in an IoT edge gateway that collects local sensor data and forwards status or configuration information. Its integrated 10/100 MAC and PHY support copper Ethernet links in panels and cabinets where wireless access is impractical. The choice of an 8-bit, 16-bit, or 32-bit host bus allows the gateway's existing processor to be reused. For deployment, account for the controller's 2.97 V to 3.63 V supply range, validate electrostatic-discharge protection at the network connector, and design firmware to reconnect logically after link loss or system resume.
Önerilen Ürünler Özeti
Mühendislik referans verileri: LAN91C111-NC — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün |
|---|---|
| Brand | Microchip Technology |
| Package | 128-pin TQFP, 14 mm x 14 mm |
| Product Function | Integrated 10/100 Ethernet MAC and PHY |
| Supported Data Rates | 10 Mbps and 100 Mbps |
| Host Interface Width | 32-bit, 16-bit, and 8-bit |
| Internal FIFO Memory | 8 KB dynamically configurable TX/RX |
| Supply Voltage Range | 2.97 V to 3.63 V |
| MAC-to-PHY Interface | Internal MII |
| Protocol | IEEE 802.3 CSMA/CD |
Ana Farklılayıcılar
- Integrated Ethernet MAC and PHY (karşılaştırma:Generic 10/100 Ethernet controller)
- Flexible parallel host interface (karşılaştırma:Fixed-width non-PCI Ethernet controller)
- Integrated frame buffering (karşılaştırma:Ethernet controller requiring external frame-buffer interface)
- Legacy embedded connectivity (karşılaştırma:Modern controller requiring a serial device interface)
Tasarım Notları
Use the manufacturer package drawing to establish the 128-pin TQFP land pattern and confirm the 14 mm by 14 mm body dimensions. Place the LAN91C111-NC according to the reference-layout guidance in the manufacturer datasheet, with the Ethernet magnetics and associated passive components positioned to minimize differential-pair discontinuity. Verify courtyard clearance, solder-mask geometry, and paste volume during PCB-library review rather than relying on a generic 128-pin symbol.
Treat the MII and parallel host-bus signals as timing-sensitive interfaces. Use the pin-description and timing tables in the manufacturer datasheet to assign address, control, interrupt, and data signals, then constrain clock and synchronous interface paths according to the implemented host bus width. Leave unused inputs in their defined states and avoid long stubs. Validate the interface at the intended host-clock and 100 Mbps operating conditions with an eye-diagram or protocol-focused test.
Do not substitute an Ethernet controller solely because both devices advertise 10/100 Mbps operation. A safe replacement must match the 128-pin TQFP footprint, host-bus width and timing, FIFO behavior, MII signals, interrupts, reset requirements, supply voltage, and register compatibility. Review each package pin and the software driver before release, and preserve the original controller's initialization sequence unless Microchip Technology explicitly documents a change.
Design the 2.97 V to 3.63 V core supply and any required I/O rails independently, following the recommended capacitor values and sequencing shown in the manufacturer datasheet. Place bulk and high-frequency decoupling capacitors close to their assigned supply pins, and verify startup, current-limit, and power-state behavior with the actual processor and network magnetics. Treat the internal 8 KB FIFO as data storage rather than a substitute for adequate supply decoupling.
Exercise firmware recovery paths before production release. Test link-down and link-up events, repeated PHY resets, malformed frames, oversized frames, FIFO pressure, and simultaneous host transmit and receive activity. Confirm that interrupt handlers clear all relevant status bits and that the driver does not overrun its buffer. These checks are particularly important when the controller was originally designed around a narrow 8-bit or 16-bit host bus.
Uyumluluk Bilgisi
Compliance declarations for the exact LAN91C111-NC orderable suffix are not stated in the manufacturer product-page text or the retrieved listings.