LAN9255-I/ZMX018 - EtherCAT Controller | Microchip
MPN: LAN9255-I/ZMX018 ✓ AktifLAN9255-I/ZMX018 Genel Bakış
An EtherCAT device controller, or ESC, is the dedicated interface between an EtherCAT network and embedded automation hardware. It manages EtherCAT frames, distributed clocks, and slave-controller behavior while exposing a parallel host interface to an application processor. The LAN9255 combines that controller role with a Cortex-M4F microcontroller and two Ethernet PHYs, reducing the number of discrete devices required in a compact industrial control design.
Key features include integration of the LAN9253 EtherCAT controller, dual full-duplex 100BASE-TX transceivers, and a SAM E53J microcontroller with 256 kB of memory. The two integrated PHYs support 100 Mbps 100BASE-TX links for EtherCAT line and power wiring. A USB 2.0 interface and RMII interface provide additional connectivity for configuration, debugging, or host-side integration.
The LAN9255 is implemented as a system-in-package that combines the EtherCAT controller, PHYs, and Cortex-M4F MCU in one 128-pin TQFP package. This integration simplifies board partitioning compared with a discrete ESC, external PHY, and separate microcontroller arrangement. It does not, however, eliminate the need for careful Ethernet layout, clock planning, decoupling, and thermal assessment.
Typical applications include compact EtherCAT slave controllers, industrial I/O modules, motion-control equipment, servo-drive interfaces, factory-automation nodes, and Ethernet-connected embedded control systems. The integrated MCU is especially useful when the slave requires local supervisory logic, diagnostics, or application-specific processing in addition to the EtherCAT datalink function.
The most important design consideration is the 128-pin mixed-signal package. Its Ethernet differential pairs, supply rails, ground structure, and high-speed digital signals require deliberate placement and routing on a multilayer PCB. Keep the PHY connections short and symmetric, provide the prescribed decoupling near the supply pins, and follow the reference layout and component-placement guidance in the manufacturer datasheet.
This product record combines the official LAN9255 datasheet, package and interface identification, lifecycle information, and drop-in comparison data in one engineering-focused reference. It also highlights the practical differences among LAN9255 ordering variants and explains when the integrated MCU, dual PHY, and 128-pin TQFP package justify the consolidation.
Drop-in alternatifler için LAN9255-I/ZMX018 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller LAN9255-I/ZMX018 (aynı form faktörü ve ayağa oturma) — farklı olan Package, Supply Voltage, Operating Temperature, Product Type.
LAN9255-V/ZMX018
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LAN9255-V/ZMX020
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LAN9255/ZMX018
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
LAN9255-I/ZMX018 Özellikler
| Device Type | 2/3-port EtherCAT device controller |
| Integrated MCU Core | 32-bit Arm Cortex-M4F |
| Integrated Memory | 256 kB |
| Integrated Ethernet PHYs | 2 full-duplex 100BASE-TX PHYs |
| Ethernet Data Rate | 100 Mbps |
| Ethernet Standard | IEEE 802.3 |
| USB Interface | USB 2.0 |
| Host Interface | RMII |
| Besleme Gerilimi | 3.3 V |
| Paket | 128-pin TQFP, 14 x 14 mm |
| Montaj Türü | Surface mount |
| EtherCAT Ports | 2/3 ports |
| Processor Architecture | 32-bit |
LAN9255-I/ZMX018 128-pin tqfp, 14 x 14 mm Pin Yapısı Kılavuzu
LAN9255-I/ZMX018 (128-pin tqfp, 14 x 14 mm paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: LAN9255-I/ZMX018.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
LAN9255-I/ZMX018 için uygundur 6 uygulamas: Compact EtherCAT Slave Controllers, Industrial Ethernet I/O Modules, Servo Drive Network Interfaces, Factory Automation Edge Nodes, Embedded EtherCAT Control Modules, Ethernet-Connected Test and Control Equipment.
Compact EtherCAT Slave Controllers
The LAN9255-I/ZMX018 fits compact EtherCAT slave designs because it combines a 2/3-port EtherCAT device controller with two integrated 100BASE-TX PHYs in one 128-pin TQFP package. The on-package Arm Cortex-M4F MCU and 256 kB of memory can handle local control or diagnostics without requiring a separate processor for basic slave logic. Its 100 Mbps PHYs support the standard EtherCAT line interface, while USB 2.0 and RMII provide useful configuration and host-integration paths. The main engineering trade-off is the dense 128-pin mixed-signal footprint, which requires a multilayer PCB and careful assignment of the Ethernet, supply, clock, and digital interfaces.
Önerilen
Industrial Ethernet I/O Modules
The LAN9255-I/ZMX018 is appropriate for industrial Ethernet I/O modules that need EtherCAT connectivity, local diagnostics, and network-facing processing in a compact controller. Its two integrated 100BASE-TX PHYs support 100 Mbps line and power-wire networking, while the Cortex-M4F MCU provides local execution capability and 256 kB of integrated memory for protocol and supervisory code. RMII can connect a host processor when the application separates network management from real-time I/O. The design must preserve the datasheet’s differential-pair routing and grounding strategy so Ethernet performance is not limited by PCB implementation.
Önerilen
Servo Drive Network Interfaces
For compact servo-drive and motion-control interfaces, the LAN9255-I/ZMX018 combines EtherCAT slave-controller functionality with two 100BASE-TX PHYs and a Cortex-M4F MCU. The integrated MCU can support state-machine logic, fault handling, and local parameter management close to the network interface, reducing the number of chips needed for a basic embedded control section. Its 128-pin TQFP package requires disciplined power and ground partitioning, especially where motor-control power stages and sensitive Ethernet circuitry coexist. Copper keepouts, controlled impedance, and isolation strategy should be designed against the manufacturer reference layout.
Önerilen
Factory Automation Edge Nodes
The LAN9255-I/ZMX018 can serve as the communications and local-processing core of a factory-automation edge node. Two integrated full-duplex 100BASE-TX PHYs eliminate separate PHY placement for typical EtherCAT line interfaces, while the Cortex-M4F MCU executes local diagnostics and supervisory functions. USB 2.0 provides a practical configuration path during commissioning, and RMII offers a connection to a separate host when the architecture separates EtherCAT traffic from higher-level control. The principal limitation is package density: the 128-pin TQFP demands careful fanout, multilayer routing, and component-placement planning to preserve signal and thermal performance.
Önerilen
Embedded EtherCAT Control Modules
The LAN9255-I/ZMX018 is useful in embedded control modules where EtherCAT functionality, Ethernet physical layers, and application processing must share a compact board area. The integrated 32-bit Cortex-M4F MCU provides local execution capability, and the 256 kB of memory reduces external component requirements for moderate firmware footprints. Its 100 Mbps dual-PHY architecture suits 100BASE-TX EtherCAT networks, while USB 2.0 can support configuration, firmware loading, or diagnostic functions. Designers should still budget external memory if the application exceeds the integrated capacity and verify the required clock, reset, and power sequencing against the manufacturer recommendations.
Önerilen
Ethernet-Connected Test and Control Equipment
The LAN9255-I/ZMX018 can form the networking core of compact test and measurement equipment requiring EtherCAT slave behavior and embedded control. The two integrated 100BASE-TX PHYs support deterministic 100 Mbps network links, and the Cortex-M4F MCU can manage local acquisition sequencing, configuration, and fault reporting. RMII can be used when a higher-performance host processor owns the main application workload, while USB 2.0 offers a convenient control or service interface. For laboratory instruments, the design should provide appropriate isolation and grounding rather than assuming that integration alone eliminates common-mode and EMC constraints.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: LAN9255-I/ZMX018 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | LAN9255-V/ZMX018 | LAN9255-V/ZMX020 | LAN9255/ZMX018 |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
Ana Farklılayıcılar
- Controller, PHYs, and MCU consolidated in one package (karşılaştırma:LAN9255-V/ZMX018)
- Integrated local processing and memory (karşılaştırma:LAN9255-V/ZMX020)
- Dual integrated 100BASE-TX Ethernet PHYs (karşılaştırma:LAN9255/ZMX018)
Tasarım Notları
Implement the Ethernet differential pairs as short, symmetrical routes with a continuous reference plane and no stubs or unnecessary vias. Follow the manufacturer reference layout for the 100BASE-TX PHYs because trace geometry, component placement, and return-path continuity directly affect signal integrity. Keep the controller, PHY, magnetics, and connector placement tightly grouped, and avoid routing Ethernet signals beneath switching-power or motor-drive circuitry.
Partition the 3.3 V supply into the controller, MCU, and Ethernet-related domains as directed by the manufacturer power architecture. Place decoupling capacitance at the associated supply pins with short ground returns, and preserve a low-impedance plane connection beneath the 128-pin TQFP. Validate startup, current transients, and supply sequencing with the complete load arrangement rather than only the idle controller.
Plan the 128-pin TQFP footprint and escape routing before placing the rest of the circuit. Separate Ethernet, RMII, USB, and clock routes from noisy power-converter paths, and maintain the package’s thermal and ground connectivity. Because the device integrates an EtherCAT controller, PHYs, and Cortex-M4F MCU, small routing mistakes can affect protocol timing, radio-frequency behavior, and Ethernet signal quality at the same time.
Do not approve LAN9255-V/ZMX018, LAN9255-V/ZMX020, or LAN9255/ZMX018 solely because the PCB footprints appear compatible. Verify the complete ordering suffix, temperature grade, qualification status, memory configuration, and firmware requirements in Microchip’s ordering information. Also confirm the required packing method and pin-1 orientation before releasing a production order.
Uyumluluk Bilgisi
The available manufacturer and distributor information does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for this ordering code. The product is an industrial Ethernet controller rather than an automotive-qualified device in the information available.